Technical data sheet LF24-S
Rotary actuator fail-safe for adjusting dampers
in technical building installations
• Air damper size up to approx. 0.8 m²
• Torque motor 4 Nm
• Nominal voltage AC/DC 24 V
• Control Open/close
• with integrated auxiliary switch
Technical data
Electrical data Nominal voltage AC/DC 24 V
Nominal voltage frequency 50/60 Hz
Nominal voltage range AC 19.2...28.8 V / DC 21.6...28.8 V
Power consumption in operation 5W
Power consumption in rest position 2.5 W
Power consumption for wire sizing 7 VA
Power consumption for wire sizing note Imax 5.8 A @ 5 ms
Auxiliary switch 1x SPDT, 0...100%
Switching capacity auxiliary switch 1 mA...3 A (0.5 A inductive), DC 5 V...AC 250 V
Connection supply / control Cable 1 m, 2x 0.75 mm²
Connection auxiliary switch Cable 1 m, 3x 0.75 mm²
Parallel operation Yes (note the performance data)
Functional data Torque motor 4 Nm
Torque fail-safe 4 Nm
Direction of motion motor selectable by mounting L/R
Direction of motion fail-safe selectable by mounting L/R
Manual override No
Angle of rotation Max. 95°
Angle of rotation note Adjustable 37...100% with integrated
mechanical limitation
Running time motor 75 s / 90°
Running time fail-safe <20 s @ -20...50°C / <60 s @ -30°C
Sound power level, motor 50 dB(A)
Mechanical interface Universal shaft clamp 8...16 mm
Position indication Mechanical
Service life Min. 60'000 fail-safe positions
Safety data Protection class IEC/EN III, Safety Extra-Low Voltage (SELV)
Protection class auxiliary switch IEC/EN II, reinforced insulation
Degree of protection IEC/EN IP54
EMC CE according to 2014/30/EU
Low voltage directive CE according to 2014/35/EU
Certification IEC/EN IEC/EN 60730-1 and IEC/EN 60730-2-14
Hygiene test According to VDI 6022 Part 1 / SWKI VA
104-01, cleanable and disinfectable, low
emission
Type of action Type 1.B
www.belimo.com LF24-S • en-gb • 2023-12-12 • Subject to change 1/3
Technical data sheet LF24-S
Technical data
Safety data Rated impulse voltage supply / control 0.8 kV
Rated impulse voltage auxiliary switch 2.5 kV
Pollution degree 3
Ambient humidity Max. 95% RH, non-condensing
Ambient temperature -30...50°C [-22...122°F]
Storage temperature -40...80°C [-40...176°F]
Servicing maintenance-free
Weight Weight 1.5 kg
Safety notes
• This device has been designed for use in stationary heating, ventilation and air-conditioning
systems and must not be used outside the specified field of application, especially in aircraft
or in any other airborne means of transport.
• Outdoor application: only possible in case that no (sea) water, snow, ice, insolation or
aggressive gases interfere directly with the device and that it is ensured that the ambient
conditions remain within the thresholds according to the data sheet at any time.
• Only authorised specialists may carry out installation. All applicable legal or institutional
installation regulations must be complied with during installation.
• The device may only be opened at the manufacturer's site. It does not contain any parts that
can be replaced or repaired by the user.
• Cables must not be removed from the device.
• To calculate the torque required, the specifications supplied by the damper manufacturers
concerning the cross-section and the design, as well as the installation situation and the
ventilation conditions must be observed.
• The device contains electrical and electronic components and must not be disposed of as
household refuse. All locally valid regulations and requirements must be observed.
Product features
Operating mode The actuator moves the damper to the operating position at the same time as tensioning the
return spring. The damper is turned back to the safety position by spring energy when the
supply voltage is interrupted.
Simple direct mounting Simple direct mounting on the damper shaft with a universal shaft clamp, supplied with an
anti-rotation device to prevent the actuator from rotating.
Adjustable angle of rotation Adjustable angle of rotation with mechanical end stops.
High functional reliability The actuator is overload protected, requires no limit switches and automatically stops when
the end stop is reached.
Flexible signalling With adjustable auxiliary switch (0...100%)
Accessories
Electrical accessories Description Type
Auxiliary switch 2x SPDT S2A-F
Feedback potentiometer 1 kΩ P1000A-F
Mechanical accessories Description Type
Shaft extension 170 mm ø10 mm for damper shaft ø6...16 mm AV6-20
Shaft clamp reversible, clamping range ø16...20 mm K6-1
Ball joint suitable for damper crank arm KH8 / KH10 KG10A
Ball joint suitable for damper crank arm KH8 KG8
Damper crank arm Slot width 8.2 mm, clamping range ø10...18 mm KH8
Actuator arm, clamping range ø8...16 mm, Slot width 8.2 mm KH-LF
www.belimo.com LF24-S • en-gb • 2023-12-12 • Subject to change 2/3
Technical data sheet LF24-S
Accessories
Description Type
Angle of rotation limiter, with end stop ZDB-LF
Form fit adapter 8x8 mm ZF8-LF
Mounting kit for linkage operation for flat installation ZG-LF1
Mounting kit for linkage operation for side installation Slot width 6.2 ZG-LF3
mm
Anti-rotation mechanism 180 mm, Multipack 20 pcs. Z-ARS180L
Electrical installation
Supply from isolating transformer.
Parallel connection of other actuators possible. Observe the performance data.
Wire colours:
1 = black
2 = red
S1 = violet
S2 = red
S3 = white
Wiring diagrams
AC/DC 24 V, open/close Auxiliary switch
Dimensions
Spindle length
Min. 84
Min. 20
Clamping range
www.belimo.com LF24-S • en-gb • 2023-12-12 • Subject to change 3/3
