Pentadur HB Zinc Primer 8537
PRODUCT DESCRIPTION
Pentadur HB Zinc 8537 is a two component polyamide cured Epoxy Primer with high loading of metallic
super fine Zinc which imparts Cathodic protection to base metal and also prevents under film creeping
corrosion. This is a fast drying type primer which help early recoatability. Product contains 80% Zinc in
dry film and confirms to SSPC-Paint 20 Type-II-level-II Organic Zinc Rich Primer, Zinc Dust
confirming to ASTM D-520 Type II
INTENDED USES As a long life primer on steel subjected to moderately to severely corrosive marine and industrial
environment, eg. Sluice gates, crest gates, penstocks, floating roofs of tanks, bunk houses, structural steel
in docks, refineries, thermal power station. Also approved for defence use
__________________________________________________________________________
PRACTICALINFORMATION FOR Pentadur HB Zinc Primer 8537
Color Grey
Gloss Level Matt
Volume Solids 65%
Typical Thickness 75-100 microns
Theoretical Coverage 6.5 – 8.67 m2/liter at 75-100 microns D.F.T.
Practical Coverage Allow appropriate loss factors
Method of Application Airless spray, Brush
Temperature Resistance Up to 120 oC (Dry heat)
Drying Time & Over Coating Intervals.
Over coating Interval
of Pentadur HB Zinc Primer 8537
Surface Hard
Temperature Dry Dry Minimum Maximum
_______________________________________________________________________
20oC (77oF) 3 hours 20 hours 10 hours 30 days
30oC (95oF) 1 hours 14 hours 6 hours 30 days
________________________________________________________________________
REGULATORY DATA Flash Point Base (Part A) C/A (Part B) Mixed
36oC (97oF) 31oC (88o F) 35oC (95oF)
________________________________________________________________________________
SYSTEMS COMPATABILITY
Where a cosmetically acceptable topcoat is required, the following products are recommended.
Pentadur MIO, Pentadur Epoxy Topcoat, Pentathane Topcoats
_________________________________________________________________________________
SURFACE PREPARATION
The performance of this product will depend upon the degree of surface preparation. The surface to be
coated must be clean, dry and free from contamination. Prior to paint application all surfaces should be
assessed and treated in accordance with ISO 8504:1992. Accumulated dirt and soluble salts must be
removed.
Pentadur HB Zinc Primer 8537
Abrasive Blast Cleaning
For atmospheric exposure performance will be achieved when Pentadure HB Zinc Primer 8537 is
applied to surfaces prepared to a minimum of Sa2½ (ISO 8501-1:1988) or SSPC-SP 10. Surface defects
revealed by the blast cleaning process, should be ground, filled or treated in the appropriate manner. A
surface profile of 50-65 microns (2- 3 mils) is recommended.
This product will perform best when applied on Surface preparation to SA-3 ( ISO-8501) or NACE 1 or
SSPC -SP-5 .
_________________________________________________________________________________
APPLICATION Mixing Material is supplied in two containers as a unit. Always mix a complete unit
in the proportions supplied. Once the unit has been mixed it must be used
within the working pot life specified.
(1) Agitate Base (Part A) with a power agitator.
(2) Combine entire contents of Curing Agent (Part B)
with Base (Part A) and mix thoroughly with power agitator
Mix Ratio 4.0 parts: 1.00 parts by volume
Working Pot 15o C 30oC 40o C
Life 8 hours 5 hours 4 hour
Airless Spray Recommended - Tip range 15-23 thou)
- Total output fluid pressure at spray tip not
Less than 176 kg/cm2 (2,500 p.s.i)
Brush Recommended for small areas, Typically 50-100 microns
Thinner Thinner 145 Do not thin more than allowed by local
Environmental legislation.
Clean Up Clean up all equipment immediately after use with Thinner 145 . It is good working
practice to periodically flush out spray equipment during the course of the working
day. Frequency of cleaning will depend upon amount sprayed, temperature and
elapsed time, including any delays. All surplus
materials and empty containers should be diagnosed of in accordance with
appropriate regional regulations / legislation.
_____________________________________________________________________
SAFETY PRECAUTIONS
This product is intended for use only by professional applicators in industrial situations in
accordance with the advice given on this sheet, the Material Safety Data Sheet and the container(s), and
should not be used without reference to the Material Safety Data sheets (MSDS) which Grauer & Weil
India Ltd has provided to its customers.
All work involving the application and use of this product should be performed in compliance with all
relevant national, Health, Safety and Environmental standards and regulations.
In the event welding or flame cutting is performed on metal coated with this product, dust and fumes will
be emitted which will require the use of appropriate personal protective equipment and adequate local
exhaust ventilation.
If in doubt regarding the suitability of use of this product, consult Grauer & Weil India Ltd for further
advice.
________________________________________________________________________________
Pentadur HB Zinc Primer 8537
PACK SIZE
20 litres unit Pentadur HB Zinc Primer 8537
________________________________________________________________________________________________________
STORAGE Shelf Life 12 months minimum at 25 deg C (77 deg F). Store in cool & Dry place
___________________________________________________________________________________________
Disclaimer
The data provided in this sheet in not intended to be exhaustive and any person using the product for any purpose other than that specifically recommended in this sheet
without first obtaining written confirmation from us as to the suitability of the product for the intended purpose does so at his own risk. While we endeavor to ensure that all
advice we give about the product either in this sheet or otherwise is correct we have no control over either the quality or condition of the substrate or the many factors
affecting the use and application of the product.
Therefore, unless we specifically agree in writing to do so, we do not accept any liability whatsoever or howsoever arising f or the performance of the product or for any loss
or damage arising out of the use of the product. The information contained in this sheet is liable to Change from time to time in the light of exp erience and our policy of
continuous product development.
It is the user’s responsibility to check that this sheet is current prior to using the product. Issue date :KC April 2020
