622Mbps SFP Optical Transceiver

 Up to 40 km on 9/125μm SMF
 Single +3.3V Power Supply
 Monitoring Interface Compliant with
SFF-8472
 Low power dissipation <600mW
typically
 Industrial /Extended/ Commercial
operating temperature range: -40°C to
85°C/-5°C to 85°C/-0°C to 70°C Version
available
Features:
 Up to 622M b/s Data Links
 Hot-Pluggable Applications:
 1310nm DFB laser transmitter  SONET OC-12/SDH STM-4
 Duplex LC connector  Other Optical Links
 RoHS compliant and Lead Free

Description:
MWS-06-31-XX Transceiver is a high performance, cost effective module which have a Duplex
LC optics interface. Standard AC coupled CML for high speed signal and LVTTL control andmonitor
signals.
The receiver section uses a PIN receiver and the transmitter uses 1310 nm DFB laser, up to 25dB
link budge ensure this module SONET OC-12/SDH STM-4 40Km application.
 Absolute Maximum Ratings
Parameter Symbol Min. Typical Max. Unit
Storage Temperature TS -40 +85 °C
Supply Voltage VCCT, R -0.5 4 V
Relative Humidity RH 0 85 %
Industrial -40 85
Case Operating Temperature Extended Top -5 85 °C
Commercial 0 70

 Recommended Operating Environment:

Parameter Symbol Min. Typical Max. Unit
Industrial -40 85 °C
Case operating Temperature Extended TC -5 85 °C
Commercial 0 70 °C
Supply Voltage VCCT, R 3.0 3.6 V
 622Mbps SFP Optical Transceiver

 Electrical Characteristics (TO P = 0 to 70 °C, VCC = 3.0 to 3.60 Volts)

Parameter Symbol Min. Typical Max. Unit Note
Supply Voltage Vcc 3.0 3.30 3.60 V
Supply Current Icc 160 280 mA
Inrush Current Isurge Icc+30 mA
Maximum Power Pmax 1.0 W
Transmitter Section:
Input differential impedance Rin 90 100 110 Ω 1
Single ended data input swing Vin P P 200 1200 mVp-p
Transmit Disable Voltage VD Vcc – 1.3 Vcc V 2
Transmit Enable Voltage VEN Vee Vee+ 0.8 V
Transmit Disable Assert Time T dessert 10 us
Receiver Section:
Single ended data output swing Vout,pp 300 1000 mv 3
Data output rise time tr 1300 ps 4
Data output fall time tf 1300 ps 4
LOS Fault Vlosfault Vcc – 0.5 VCC_host V 5
LOS Normal Vlos norm Vee Vee+0.5 V 5
Power Supply Rejection PSR 100 mVpp 6
Note:
1. AC coupled.
2. Or open circuit.
3. Into 100 ohm differential termination.
4. 20 – 80 %
5. LOS is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected.
6. All transceiver specifications are compliant with a power supply sinusoidal modulation of 20 Hz to
1.5MHz up to specified value applied through the power supply filtering network shown on page 23 of the
Small Form-factor Pluggable (SFP) Transceiver Multi-Source Agreement (MSA), September 14, 2000.

 Optical Parameters(TO P = 0 to 70 °C, VCC = 3.00 to 3.60 Volts)

Parameter Symbol Min. Typical Max. Unit Note
Transmitter Section:
Center Wavelength λc 1260 1310 1355 nm 1
Spectral Width(-20dB) σ 1 nm
Optical Output Power Pout -3 +2 dBm 2
Optical Rise/Fall Time tr / tf 1300 ps 3
Extinction Ratio ER 9.2 dB
Compliant with Eye Mask Defined in IEEE 802.3
Eye Mask for Optical Output
standard
Receiver Section:
Optical Input Wavelength λ 1260 1600 nm
Optical Input Power Pin -28 -3 dBm 4.5
Receiver Reflectance 12 dB
 622Mbps SFP Optical Transceiver
Receiver Overload Pol -3 dBm 4.5
RX Sensitivity Sen -28 dBm 4.5
RX_LOS Assert LOS A -40 dBm
RX_LOS Deassert LOS D -30 dBm
RX_LOS Hysteresis LOS H 2 2.5 dB
General Specifications
Data Rate BR 622 Mb/s
-12
Bit Error Rate BER 10
Max. Supported Link Length on 120 km 6
LMAX
9/125μm SMF@155Mb/s
Total System Budget LB 25 dB 7
Note
1. Also specified to meet curves in FC-PI 13.0 Figures 18 and 19, which allow trade-off between wavelength
spectral width.
2. Class 1 Laser Safety per FDA/CDRH and EN (IEC) 60825 regulations.
3. Unfiltered, 20-80%. Complies with IEEE 802.3 (Gig. E), FC 1x and 2x eye masks when filtered.
4. Measured with conformance signals defined in FC-PI 13.0 specifications.
31 -12
5. Measured with PRBS 2 -1at 10 BER
6. Dispersion limited per FC-PI Rev. 13
7. .Attenuation of 0.25 dB/km is used for the link length calculations. Distances are indicative only. Please
refer to the Optical Specifications in Table IV to calculate a more accurate link budget based on specific
conditions in your application.

 Digital Diagnostic Monitor Characteristics

The following digital diagnostic characteristics are defined over the Recommended Operating
Environment unless otherwise specified. It is compliant to SFF8472 Rev10.2 with internal calibration mode.
For external calibration mode please contact our sales stuff..
Parameter Symbol Min. Max. Unit
Temperature monitor absolute error DMI_Temp -3 3 degC
Laser power monitor absolute error DMI_TX -3 3 dB
RX power monitor absolute error DMI_RX -3 3 dB
Supply voltage monitor absolute error DMI_VCC -0.08 0.08 V
Bias current monitor DMI_Ibias -10% 10% mA

 Block Diagram of Transceiver:

 622Mbps SFP Optical Transceiver

+TX_ DAT
LD
-TX_ DAT LD
Driver

TX_ Disable
TOSA
TX_ Fault

MOD_DEF(0)
MOD_DEF(1)
MOD DEF
MOD_DEF(2)
ROSA
+RX_DAT
Pre-Amp
-Rx_ DAT Post-Amp
Rx_ LOS

Figure1: Block Diagram

 Pin Assignment:

Figure2:Diagram of Host Board Connector Block Pin Numbers and Names

622Mbps SFP Optical Transceiver

Figure 3. SFP Host Board Mechanical Layout

Figure 4. SFP Host Board Mechanical Layout(Cont)

 622Mbps SFP Optical Transceiver
 Pin Description:
Pin No Name Function Plug Seq Notes
1 VeeT Transmitter Ground 1 1
2 TX Fault Transmitter Fault Indication 3
3 TX Disable Transmitter Disable 3 2
4 MOD-DEF2 Module Definition 2 3
5 MOD-DEF1 Module Definition 1 3 3
6 MOD-DEF0 Module Definition 0 3 3
7 Rate Select Not Connected 3 4
8 LOS Loss of Signal 3 5
9 VeeR Receiver Ground 1 1
10 VeeR Receiver Ground 1 1
11 VeeR Receiver Ground 1
12 RD- Inv. Received Data Out 3 6
13 RD+ Received Data Out 3 6
14 VeeR Receiver Ground 3 1
15 VccR Receiver Power 2 1
16 VccT Transmitter Power 2
17 VeeT Transmitter Ground 1
18 TD+ Transmit Data In 3 6
19 TD- Inv. Transmit In 3 6
20 VeeT Transmitter Ground 1
Notes:
1. Circuit ground is internally isolated from chassis ground.
2. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V.
3. Should be pulled up with 4.7k - 10 kohms on host board to a voltage between 2.0V and
3.6V.MOD_DEF(0) pulls line low to indicate module is plugged in.
4. Rate select is not used
5. LOS is open collector output. Should be pulled up with 4.7k – 10 kohms on host board to a voltage
between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.
6. AC Coupled

 Recommended Circuit:
 622Mbps SFP Optical Transceiver

Host Board SFP Module

VCC(3.3V) VCCT
4K7 to10KΩ
TX_Disable
TX_Fault

Z=50Ω
Laser
PECL Z=50Ω 100Ω
Driver

Z=50Ω

PECL 100Ω Amplifer

Z=50Ω

RX_LOS
4K7 to10KΩ
VCC(3.3V)

3X4K7 to10KΩ
MOD_DEF(2)

MOD_DEF(1) EEPROM
MOD_DEF(0)
RGND

Figure 5. SFP Host Recommended Circuit

 Serial ID Memory Contents:

Data Length Name of
Description and Contents
Address (Byte) Length
Base ID Fields
0 1 Identifier Type of Serial transceiver (03h=SFP)
1 1 Reserved Extended identifier of type serial transceiver (04h)
2 1 Connector Code of optical connector type (07=LC)
3-10 8 Transceiver SONET
11 1 Encoding SONET Scrambled
12 1 BR,Nominal Nominal baud rate, unit of 100Mbps
13 1 Reserved (0000h)
14 1 Length(9um,km) Link length supported for 9/125um fiber, units of km
15 1 Length(9um) Link length supported for 9/125um fiber, units of 100m
16 1 Length(50um) Link length supported for 50/125um fiber, units of 10m
17 1 Length(62.5um) Link length supported for 62.5/125um fiber, units of 10m
18 1 Length(Copper) Link length supported for copper, units of meters
19 1 Reserved
20-35 16 Vendor Name SFP vendor name:
36 1 Reserved
37-39 3 Vendor OUI SFP transceiver vendor OUI ID
40-55 16 Vendor PN Part Number: “MWS-06-55-120” (ASCII)
56-59 4 Vendor rev Revision level for part number
60-61 2 Wavelength Laser wavelength
62 1 Reserved
63 1 CCID Least significant byte of sum of data in address 0-62
 622Mbps SFP Optical Transceiver
Extended ID Fields
Indicates which optical SFP signals are implemented(001Ah
64-65 2 Option
= LOS, TX_FAULT, TX_DISABLE all supported)
66 1 BR, max Upper bit rate margin, units of %
67 1 BR, min Lower bit rate margin, units of %
68-83 16 Vendor SN Serial number (ASCII)
84-91 8 Date code Manufacturing date code
92 1 Diagnostic Type Diagnostics
93 1 Enhanced Options Diagnostics
94 1 SFF-8472 Diagnostics
95 1 CCEX Check code for the extended ID Fields (addresses 64 to 94)
Vendor Specific ID Fields
96-127 32 Readable Vendor specific date, read only

 Diagnostics Memory Contents(A2h):

Data Length Name of
Description and Contents
Address (Byte) Length
Diagnostic and control/status fields
0-39 40 A/W Thresholds Diagnostic Flag Alarm and Warning Thresholds
40-55 16 Unallocated
56-91 16 Ext Cal Constants Diagnostic calibration constants for optional External Calibration
92-94 3 Unallocated
95 1 CC_DMI Check code for Base Diagnostic Fields (addresses 0 to 94)
96-105 10 Diagnostics Diagnostic Monitor Data (internally or externally calibrated)
106-109 4 Unallocated
110 1 Status/Control Optional Status and Control Bits
111 1 Reserved Reserved for SFF-8079
112-113 2 Alarm Flags Diagnostic Alarm Flag Status Bits
114-115 2 Unallocated
116-117 2 Warning Flags Diagnostic Warning Flag Status Bits
118-119 2 Ext Status/Control Extended module control and status bytes
General use fields
120-127 8 Vendor Specific Vendor specific memory addresses
128-247 120 User EEPROM User writable non-volatile memory
248-255 8 Vendor Control Vendor specific control addresses

 References
1. Small Form-factor Pluggable (SFP) Transceiver Multi-source Agreement (MSA) September
14, 2000.
2. Bellcore GR-253 and ITU-T G.957 Specifications.

 Mechanical Dimensions:
 622Mbps SFP Optical Transceiver

Figure 6. Mechanical Drawing

Ordering information
Part Number Product Description
MWS-06-85-M Multimode 850nm, 622Mbps, LC, 500m, 0°C~+70°C
MWS-06-31-S Singlemode 1310nm, 622Mbps, LC, 2km, 0°C~+70°C
MWS-06-31-20 Singlemode 1310nm, 622Mbps, LC, 20km, 0°C~+70°C
MWS-06-31-40 Singlemode 1310nm, 622Mbps, LC, 40km, 0°C~+70°C