On Common Ground

Service Tools Catalog

www.teamoiltools.com
© 2012 TEAM Oil Tools. All rights reserved.
 www.teamoiltools.com
© 2012 TEAM Oil Tools. All rights reserved.
 On Common Ground

TABLE OF CONTENTS

P/N Product Description Page

Type “P” Index Valve #001 1

Type “P” Index Valve #002 1

Selective Treating Assembly #024 2

Type 10-20 Hydraulic Setting Tool #025 3

T525 SC Unloader 4

T572 “K” Connector Valve 5

T574 DFV Fluid Control Valve 6

T577 TS-U Spring Loaded Retrieving Tool 7

T613 HD Compression Packer 8

T621 32A Tension Set Packer 9

T727 TSW Bridge Plug 10

T1060 Model “G” Hydraulic Setting Tool 11

For more information, go to TeamOilTools.com or call 281.602.7815

© 2012 TEAM Oil Tools. All rights reserved. 042512
 On Common Ground

Type “P” Index Valve # 001 / #002

Type “P” Index Valve # 001

The “P” Index Valve is primarily used to convert a double grip mechanical set packer into a
retrievable bridge plug. This high pressure valve provides a system to run a retrievable bridge
plug with the valve open and set the bridge plug then close the valve.

features and benefits

 Large by-pass for running and retrieving
 Proven reliable seal and design method
 By-pass locked in the closing

Type “P” Index Valve # 002

The Type “P” Retrieving Tool is used to control the setting and releasing of double grip mechanical
set bridge plugs using the type “P” index valve, product 001.

features and benefits

 Controls the index valve locking and unlocking system
 Circulates fluid to wash debris prior to or after latching onto the index

For more information, go to TeamOilTools.com or call 281.602.7815

© 2012 TEAM Oil Tools. All rights reserved. Patents: www.teamoiltools.com/Innovation/TEAM-Patents 042512

1
 On Common Ground

Selective Treating Assembly #024

The S.T.A. is a cup type selective treating assembly, which is designed to selectively acidize
predetermined perforated intervals. The S.T.A. will isolate intervals from 12 inches. To any length
by the addition of standard tubing pups joints, A large built-in annular bypass, make the S.T.A.
easy to run and retrieve. Drag blocks, using Inconel springs, provide drag for a positive method of
controlling the circulating valve. The retrievable control bar is used to blank off the lower portion
below the stimulation ports

Operations
The assembly is run into the well with the circulating valve open and the assembly positioned just
above the perforated interval to be stimulated. The circulation valve is closed and the control bar
is dropped from surface or is run with the S.T.A., to pressure test the S.T.A.’s complete assembly.
Opening the circulation valve will equalize the tubing to annulus. The S.T.A. tool can now be
returned to the proper stimulation interval by dropping the fluid control valve and closing the
circulation valve, a feed rate can be taken. Opening the circulation valve will permit the treating
fluid to be circulated to the S.T.A. tool for treatment. By closing the circulation valve the stimulation
treatment can be performed. To move the S.T.A. tool to a new interval for further treatment, pick up
on the work string each interval until completed. To test the treated intervals, move the complete
assembly above the perforations and set the packer. To retrieve the assembly, open the circulating
valve and remove the work string from the well.

Control Bar Specifications

Fishing Neck Size
1in. OTIS RB 1.25in. OTIS RB Pulling Tool
Pulling Tool
Size Size Size
Inches (mm) Inches (mm) Inches (mm)
4.500 (114.30) 5.500 (139.70) 7.000 (177.80)
0.750 (19.05) 1.187 (30.15) 1.187 (30.15)

For more information, go to TeamOilTools.com or call 281.602.7815

© 2012 TEAM Oil Tools. All rights reserved. Patents: www.teamoiltools.com/Innovation/TEAM-Patents 042512

2
 On Common Ground

Type 10-20 Hydraulic Setting Tool #025

The Type 10-20 Hydraulic Setting Tool is designed to be run on drill pipe ,tubing, endless tubing or
other handling equipment that can transmit pressure to the setting tool for the purpose of setting
bridge plugs, cement retainers, retainer production packers, and services plugs or packers
normally set by wireline. It is especially applicable to setting plugs or packers in deviated wells or
in locations where a wireline unit is not available or practical.

Optional By-Pass
A large integral by-pass allows the setting tool to be run with fluid entering the running string
establishing circulation prior to the setting operation.

features and benefits

 Run on drill pipe, tubing or endless tubing
 By-pass may be run open or closed
 Pressure stages may be added or removed depending on setting pressure generated
 Running string may be drained or closed after setting

Type 10-20 Hydraulic Setting Tool #025

Size Range Max O.D. Setting Setting
Inches (mm) Inches (mm) stroke force
Inches (mm) lbs (daN)
4.500-5.000 (114.3-127.0) 3.630 (92.20) 8.250 (209.55) 35,000 (15,570)
5.500-13.375 (139.7-339.7) 4.390 (111.51) 8.250 (209.55) 50,000 (22,240)

Setting Chamber
Sq Area/Stage
First Stage - 7.060
Additional Stage - 5.840

For more information, go to TeamOilTools.com or call 281.602.7815

© 2012 TEAM Oil Tools. All rights reserved. Patents: www.teamoiltools.com/Innovation/TEAM-Patents 042512

3
 On Common Ground

SC Unloader

The T525 SC Tension Unloader is usually run above the T621 32A Tension Set Service Packer to
equalize tubing and annulus pressure differentials and facilitate the packer being unset and either
relocated or retrieved. It is run and retrieved with the latching collet in the open position to allow
fluid through the packer mandrel and minimize flow around the elements reducing swabbing.
When tension is applied to set the packer this also closes the unloader and the collet latches in
place and remains there until sufficient compressive forces are applied. The tool is full open
matching the packer I.D.

features and benefits

 Rugged heavy duty collet allows repeated use.
 Large by-pass area.
 Simple operation-tension to close, compression to open.
 Full bore I.D. matching the tension packer.
 Remains open when running or retrieving thus minimizing swabbing tendencies.

SC Unloader
Size Max O.D. Min I.D. SEAL Product
Inches (mm) Inches (mm) Inches (mm) Number
1.625 (41.28) 3.250 (82.55) 1.610 (40.89) NITRILE T525-16A-000
2.375 (60.33) 3.750 (95.25) 1.985 (50.42) NITRILE T525-20A-000
2.875 (73.03) 4.515 (114.68) 2.485 (63.12) NITRILE T525-25A-000
3.500 (88.90) 5.469 (138.91) 1.985 (50.42) NITRILE T525-35A-000

For more information, go to TeamOilTools.com or call 281.602.7815

© 2012 TEAM Oil Tools. All rights reserved. Patents: www.teamoiltools.com/Innovation/TEAM-Patents 042512

4
 On Common Ground

“K” Connector Valve

The T129 “K” Connector Valve is a high pressure mechanically operated valve used to convert a
double grip retrievable packer to a bridge plug. The T129 “K” Connector design allows pressure to
equalize above and below before the packer is released. The running retrieving tool is locked to the
valve eliminating accidental separation.

Running
Run the bridge plug to depth and pick up holding left-hand torque, set down while maintaining left-
torque (this will engage j-pin in locked position) and pick up holding left hand torque will release the
running retrieving tool from the valve.

Retrieving
Circulate debris from top of Bridge Plug and lower retrieving tool until engaged. Apply right hand
torque and pick up allowing pressure to equalize before proceeding with packer release.

features and benefits

 Equalizes pressure before packer is released
 Bonded seals for repeated use under pressure
 Auto Jay retrieving tool for easy connecting
 10,000 psi pressure rating

“K” Connector Valve

Size Casing Weight Max O.D. Min I.D. Running Product
Inches (mm) lbs/ft (kg/m) Inches (mm) Inches (mm) tool Number Number
4.500 (114.30) 9.5-13.5 (14.1-20.9) 3.750 (95.25) 1.750 (44.45) T128-45A-000 T129-45A-000
5.000 (127.00) 11.5-15.0 (17.1-22.3) 3.750 (95.25) 1.750 (44.45) T128-45A-000 T129-45A-000
5.000 (127.00) 18.0-20.8 (26.8-31.0) 3.750 (95.25) 1.750 (44.45) T128-45A-000 T129-45A-000
5.500 (139.70) 13.0-20.0 (19.3-29.8) 4.500 (114.30) 1.750 (44.45) T128-55A-000 T129-45A-000
5.500 (139.70) 20.0-23.0 (29.8-34.2) 4.500 (114.30) 1.750 (44.45) T128-55A-000 T129-45A-000
7.000 (177.80) 17.0-26.0 (25.3-38.7) 5.400 (137.16) 1.750 (44.45) T128-70A-000 T129-45A-000
7.000 (177.80) 26.0-32.0 (38.7-47.6) 5.400 (137.16) 1.750 (44.45) T128-70A-000 T129-45A-000

For more information, go to TeamOilTools.com or call 281.602.7815

© 2012 TEAM Oil Tools. All rights reserved. Patents: www.teamoiltools.com/Innovation/TEAM-Patents 042512

5
 On Common Ground

DFV Fluid Control Valve

The T574 Fluid Control Valve is a high pressure, ball type, tubing actuated fluid control valve. The
DFV Fluid control valve holds pressure from above and below, rotates open or closed with 1⁄2 turn
at the valve, and can be assembled to open with right or left hand rotation making it operational
with a variety of production packers. The DFV valve applications range from tubing tester, washing,
acidizing, fracing and converting double grip production packer into temporary bridge plug.

features and benefits

 Holds pressure from above and below
 1/2 Turn to open and close
 Assembles for right or left hand rotation to open
 Tubing can be left in tension, compression or neutral

DFV Fluid Control Valve

Tubing Size Max O.D. min i.d. Product
Inches (mm) Inches (mm) Inches (mm) Number
2.375EUE (60.30) 3.771 (95.78) 1.750 (44.45) T574-20A-000

For more information, go to TeamOilTools.com or call 281.602.7815

© 2012 TEAM Oil Tools. All rights reserved. Patents: www.teamoiltools.com/Innovation/TEAM-Patents 042512

6
 On Common Ground

TS-U Spring Loaded Retrieving Tool

The T577 Spring Loaded Retrieving Tool is used with the TS-U Retrievable Bridge Plug. The
spring loaded design minimizes the possibility of the bridge plug coming free during running and
retrieving. The strong compression spring keeps the bridge plug J- pins securely locked in the
retrieving tool jay until sufficient weight collapses the spring allowing the retrieving tool to be
removed.

features and benefits

 Spring loaded design
 Full bore design for maximum circulation
 Durable construction

TS-U Spring Loaded Retrieving Tool

Size Casing Weight Max O.D. min i.d. Product
Inches (mm) lbs/ft (kg/m) Inches (mm) Inches (mm) Number
4.500 (114.30) 9.5-13.5 (14.1-20.1) 3.750 (95.25) 2.000 (50.80) T577-45A-000
5.000 (127.00) 11.5-15.0 (17.1-22.3) 3.750 (95.25) 2.000 (50.80) T577-45A-000
5.000 (127.00) 18.0-20.8 (26.8-31.0) 3.750 (95.25) 2.000 (50.80) T577-45A-000
5.500 (139.70) 13.0-20.0 (19.3-29.8) 4.500 (114.30) 2.000 (50.80) T577-55A-000
5.500 (139.70) 20.0-23.0 (29.8-34.2) 4.500 (114.30) 2.000 (50.80) T577-55A-000
5.500 (139.70) 13.0-20.0 (19.3-29.8) 4.500 (114.30) 2.375 (60.30) T577-56A-000
5.500 (139.70) 20.0-23.0 (29.8-34.2) 4.500 (114.30) 2.375 (60.30) T577-56A-000
7.000 (177.80) 17.0-26.0 (25.3-38.7) 5.875 (149.23) 2.500 (60.80) T577-70A-000
7.000 (177.80) 26.0-32.0 (34.2-43.2) 5.875 (149.23) 2.500 (60.80) T577-70A-000

For more information, go to TeamOilTools.com or call 281.602.7815

© 2012 TEAM Oil Tools. All rights reserved. Patents: www.teamoiltools.com/Innovation/TEAM-Patents 042512

7
 On Common Ground

HD Compression Packer

The T613 HD is a heavy duty compression set retrievable packer, designed for general purpose
service work, which can hold high differential pressures from above or below. It is set by a
quarter turn at the packer followed by set down weight and the hydraulically operated upper hold-
down buttons anchor the packer when it is subject to high differential pressures from below. The
HD packer may be run with a mechanical set bridge plug for straddling intervals and can perform
multiple procedures in a single run. The packer’s internal unloader allows circulation below the
hold-down buttons making it easier to retrieve. The internal bypass also provides for circulation
around the tool thereby allowing faster trip time with less tendency of swabbing.

features and benefits

 Tubing connections are standard on the full-bore mandrel.
 Pressure-balanced mandrel hold-downs counteract pressure from below.
 Set by a quarter turn at the packer and released by picking up.
 Can be dressed to set with a quarter turn to the right or left as required.
 Can be dressed with carbide slips and hold down buttons for long life.
 The large-diameter hold-down buttons reduce casing damage.

HD Packer
Size Max O.D. min i.d. Temp. Pressure Product
Inches (mm) Inches (mm) Inches (mm) rating rating Number
°F (°C) psi (bar)
4.500 (114.30) 3.656 (92.86) 1.859 (47.22) 300 (148.89) 10,000 (689.48) T613-45B-000
4.500 (114.30) 3.750 (95.25) 1.859 (47.22) 300 (148.89) 10,000 (689.48) T613-45A-000
4.500 (114.30) 3.812 (96.82) 1.859 (47.22) 300 (148.89) 10,000 (689.48) T613-45D-000
5.000 (127.00) 4.000 (101.60) 1.859 (47.22) 300 (148.89) 10,000 (689.48) T613-50B-000
5.000 (127.00) 4.125 (104.78) 1.859 (47.22) 300 (148.89) 10,000 (689.48) T613-50A-000
5.500 (139.70) 4.500 (114.30) 1.984 (50.39) 300 (148.89) 10,000 (689.48) T613-55B-000
5.500 (139.70) 4.625 (117.48) 1.984 (50.39) 300 (148.89) 10,000 (689.48) T613-55A-000
6.625 (168.28) 5.375 (136.53) 2.484 (63.09) 300 (148.89) 10,000 (689.48) T613-65D-000
6.625 (168.28) 5.500 (139.70) 2.484 (63.09) 300 (148.89) 10,000 (689.48) T613-65A-000
6.625 (168.28) 5.750 (146.05) 2.484 (63.09) 300 (148.89) 10,000 (689.48) T613-65B-000
7.000 (177.80) 5.875 (149.23) 2.484 (63.09) 300 (148.89) 10,000 (689.48) T613-70A-000
7.000 (177.80) 5.969 (151.61) 2.484 (63.09) 300 (148.89) 10,000 (689.48) T613-70C-000
7.000 (177.80) 6.000 (152.40) 2.484 (63.09) 300 (148.89) 10,000 (689.48) T613-70B-000
7.650 (193.68) 6.453 (163.91) 2.484 (63.09) 300 (148.89) 10,000 (689.48) T613-75A-000
7.650 (193.68) 6.672 (169.47) 2.484 (63.09) 300 (148.89) 10,000 (689.48) T613-75C-000
8.625 (219.08) 7.531 (191.29) 2.984 (75.79) 300 (148.89) 8,000 (551.58) T613-85A-000
9.625 (244.48) 8.250 (209.55) 3.938 (100.03) 300 (148.89) 8,000 (551.58) T613-95A-000

For more information, go to TeamOilTools.com or call 281.602.7815

© 2012 TEAM Oil Tools. All rights reserved. Patents: www.teamoiltools.com/Innovation/TEAM-Patents 042512

8
 On Common Ground

32A Tension Set Packer

The T621 32A Tension Set Service Packer is a versatile tool, set by a 1/3 turn at the packer with
applied tension and released by compression. When set it holds pressure differential both from
above and below. Its’ rugged design facilitates multiple set/unset/reset cycles to be performed on
a single trip and it can be used for a variety of operations such as squeeze cementing, simulation,
straddle operations in combination with a retrievable bridge plug etc. The full bore design avoids
restrictions and allows access for thru tubing tools. It has a left-hand thread emergency release
system activated by right-hand rotation which allows the cone to move and the slips can fully
retract.

features and benefits

 Set by tension, released by compression.
 Bidirectional slips allow it to hold pressure from above or below.
 Rugged heavy duty construction allows multiple setting cycles in a single trip.
 Emergency safety joint release allows circulation above the slips.
 Available in left or right hand set.
 Full opening design.
 Available with premium elastomers and construction material upon special order.

32A Tension Set Service Packer

Size Max O.D. min i.d. Temp. packing Product
Inches (mm) Inches (mm) Inches (mm) rating element Number
°F (°C)
2.875 (73.03) 2.250 (57.15) 0.735 (18.67) 275 (135.00) 80-80 NITRILE T620-25A-000
3.500 (88.90) 2.750 (69.85) 0.735 (18.67) 275 (135.00) 80-80 NITRILE T620-30A-000
4.000 (101.60) 3.250 (82.55) 1.610 (40.89) 250 (121.11) 90-70-90 NITRILE T621-40A-000
4.500 (114.30) 3.750 (95.25) 1.923 (48.84) 250 (121.11) 90-70-90 NITRILE T621-45A-000
5.000 (127.00) 4.000 (101.60) 1.923 (48.84) 250 (121.11) 90-70-90 NITRILE T621-50B-000
5.000 (127.00) 4.125 (104.78) 1.923 (48.84) 250 (121.11) 90-70-90 NITRILE T621-50A-000
5.500 (139.70) 4.500 (114.30) 1.985 (50.42) 250 (121.11) 90-70-90 NITRILE T621-55B-000
5.500 (139.70) 4.625 (117.48) 1.985 (50.42) 250 (121.11) 90-70-90 NITRILE T621-55A-000
6.625 (168.28) 5.625 (142.88) 2.485 (63.12) 250 (121.11) 90-70-90 NITRILE T621-65E-000
7.000 (177.80) 5.875 (149.23) 2.485 (63.12) 250 (121.11) 90-70-90 NITRILE T621-70A-000
7.000 (177.80) 6.000 (152.40) 2.485 (63.12) 250 (121.11) 90-70-90 NITRILE T621-70B-000
7.625 (193.68) 6.453 (163.91) 2.485 (63.12) 250 (121.11) 90-70-90 NITRILE T621-75A-000
7.625 (193.28) 6.625 (168.28) 2.485 (63.12) 250 (121.11) 90-70-90 NITRILE T621-75B-000
7.625 (193.28) 6.672 (169.47) 2.485 (63.12) 250 (121.11) 90-70-90 NITRILE T621-75C-000
8.625 (219.08) 7.500 (190.50) 2.485 (63.12) 250 (121.11) 90-70-90 NITRILE T621-85A-000
9.625 (244.48) 8.250 (209.55) 2.985 (75.82) 250 (121.11) 90-70-90 NITRILE T621-95A-000
10.750 (273.05) 9.437 (239.70) 3.452 (87.68) 250 (121.11) 90-70-90 NITRILE T621-10B-000

For more information, go to TeamOilTools.com or call 281.602.7815

© 2012 TEAM Oil Tools. All rights reserved. Patents: www.teamoiltools.com/Innovation/TEAM-Patents 042512

9
 On Common Ground

TSW Bridge Plug

The T727 TSW Bridge Plug is a high pressure retrievable bridge plug suitable for use in selective
treating and testing of multiple zones. It is typically set mechanically on tubing or drillpipe but
can be supplied in an electric line set version for special applications. The design includes a large
internal by-pass area, to prevent swabbing while running or retrieving. The by-pass closes off
during the setting process and re-opens during the retrieving process prior to the upper slips
releasing so as to equalize pressure across the plug before it unsets. It can be set in tension
making it ideal for use in boh shallow applications, such as testing wellheads, and in deep set
operations.

features and benefits

 Suitable for use at any depth.
 Standard tool is set and released by a 1/4 turn to the right and pipe reciprocation.
Other J-slot configurations are available.
 Large by-pass area to prevent swabbing.
 The pressure across the tool is equalized before unsetting.
 Available in electric line set version.
 An emergency shear release mechanism is part of the design.

TSW Bridge Plug

Size Max O.D. Temp. Running Wireline Product
Inches (mm) Inches (mm) rating tool adaptor kit Number
°F (°C)
4.500 (114.30) 3.625 (92.08) 275 (135) T577-45B-000 T719-45B-000 T727-45B-000
4.500 (114.30) 3.750 (95.25) 275 (135) T577-45B-000 T719-45A-000 T727-45A-000
5.000 (127.00) 4.000 (101.60) 275 (135) T577-45A-000 T719-45A-000 T727-50B-000
5.000 (127.00) 4.125 (104.78) 275 (135) T577-45A-000 T719-45A-000 T727-50A-000
5.500 (139.70) 4.406 (111.91) 275 (135) T577-45A-000 T719-45A-000 T727-55E-000
5.500 (139.70) 4.500 (114.30) 275 (135) T577-55A-000 T719-55A-000 T727-55B-000
5.500 (139.70) 4.625 (117.48) 275 (135) T577-55A-000 T719-55A-000 T727-55A-000
6.000 (152.40) 5.188 (131.78) 275 (135) T577-55A-000 T719-55A-000 T727-60A-000
6.625 (168.28) 5.500 (139.70) 275 (135) T577-65A-000 T719-65A-000 T730-65A-000
6.625 (168.28) 5.750 (146.05) 275 (135) T577-65B-000 T719-65B-000 T730-65B-000
7.000 (177.80) 5.875 (149.23) 275 (135) T577-70A-000 T719-70A-000 T730-70A-000
7.000 (177.80) 6.000 (152.40) 275 (135) T577-70A-000 T719-70A-000 T730-70B-000
7.000 (177.80) 5.969 (151.61) 275 (135) T577-70A-000 T719-70A-000 T730-70C-000
7.625 (193.68) 6.453 (163.91) 275 (135) T577-75A-000 T719-75A-000 T730-75A-000
7.625 (193.68) 6.672 (169.47) 275 (135) T577-75A-000 T719-75A-000 T730-75C-000
US PAT # 7,082,991

For more information, go to TeamOilTools.com or call 281.602.7815

© 2012 TEAM Oil Tools. All rights reserved. Patents: www.teamoiltools.com/Innovation/TEAM-Patents 042512

10
 On Common Ground

Model G Hydraulic Setting Tool

The T1060 Model G Hydraulic Setting Tool is designed for use in setting permanent or retrievable
type seal bore production packers on pipe using a standard wireline adapter kit. It can be used
with any wireline adapter kit, which is compatible with a standard size #20 E-4 type electric line
setting tool, to set packers size 6-5/8” and larger. It has a 1.75” bore allowing circulation while
running in the well and is operated by circulating a 1” setting ball to a 0.808” ID seat at the bottom
of the tool and applying pressure from surface. Once the packer has been set, overpressure
shears out the ball and seat and opens a drain port so that circulation or draining can occur while
pulling out.

features and benefits

 Can be used to set any seal bore packer, permanent or retrievable.
 Compatible with standard wireline adapter kits.
 Provides the ability to circulate at any time while running in.
 Dual setting chambers each with an area of 10.652sq. in. providing high setting force
capabilities.
 When activated and released from the packer, ports are opened in the tool to allow fluid
circulation or drainage.
 Top connection is 2-3/8” EU Box.
 Minimum ID 1.75” through the tool and 0.808” through the ball seat.

Model G Hydraulic Setting Tool

Size Max O.D. min i.d. Temp. pressure Product
Inches (mm) Inches (mm) Inches (mm) rating rating Number
°F (°C) psi (bar)
7.000 (177.80) 5.470 (138.94) 0.808 (20.52) 300 (148.89) 10,000 (689.48) T1060-70A-000

For more information, go to TeamOilTools.com or call 281.602.7815

© 2012 TEAM Oil Tools. All rights reserved. Patents: www.teamoiltools.com/Innovation/TEAM-Patents 042512

11
 www.teamoiltools.com
© 2012 TEAM Oil Tools. All rights reserved.
On Common Ground

www.teamoiltools.com
© 2012 TEAM Oil Tools. All rights reserved.