Timber

MOULDINGS
QUALITY PRODUCED WITH PRIDE
 PurePine Radiata
Decorative
Profiles
1
Mouldings are available in fingerjointed radiata, radiata clears,
untreated/H3.1 treated, unprimed/primed, white

2
Fingerjointed mouldings are manufactured in 5.4m lengths, door jambs
in 4.2m lengths. Preprimed treated weatherboards
and fascia in 6.0m lengths

Clear radiata mouldings or profiles are supplied in random lengths only

Important Notice to all our Customers

All our product is supplied kiln dried to an average 12% moisture content at the time of dispatch.
Merchants and end users must ensure that care is taken to maintain the product in a dry environment
at all times. Moisture uptake is easily detected by swelling between the joints in finger jointing and
raised grain in finger jointing and clear profiles.

We do not warranty product that has become wet or damp for any reason, and is showing defects to
the finished surface as described above.

A dry storage environment is also required for treated preprimed product. Primer coats are not
designed as a sealer coat but simply as a holding coat.

So remember - always store all PurePine Radiata Decorative Profiles out of the weather! Always
store well supported either vertical or horizontal, and keep off the ground or floor.

1
 General Information
1 Mouldings are available in fingerjointed radiata and radiata clears.

2 Fingerjointed mouldings are 5.4m lengths. Pre-primed weatherboards and fascias are 6.0m
lengths.

3 We accept with pleasure orders and enquiries for non-standard profiles. Such orders and
enquiries will be by quotation only and cannot be cancelled or returned once the order is
confirmed.

4 All radiata and fingerjointed profiles are available in H3.1 (treated) specification if required.

5 Always store PurePine profiles out of the weather. This includes pre-primed products. Always
store well supported either vertical or horizontal and keep off the ground or the floor. Always
handle with care.

6 All prices are subject to change without prior warning.

Bundle Specifications

20 piece FJ 108m 15 piece FJ 81m 10 piece FJ 54m 5 piece FJ 27m Single pieces 5.4m
Clears 100m Clears 75m Clears 50m Clears 25m Clears random

Profile No. Profile No. Profile No. Profile No. Profile No.

14 1 2 022 103 3 16 20A 30 94 22A 31 95 99 96 111 823B

4 5 6 7 8 101B 113 813 110 114 115
9 10 11 12 822 823 822A 823A
816 46 13 13A 40x27
13B 13C 13D Eaves Mould
18 19 19A 20
21 22 23 24
24A 25 26
26A 27 28 28A
29 101 101A
102 T7 T8
326 42 43
48 725 725A
91 92 93 105
106 108 109

2
 Specific Information

Kiln
l dried timber will be dried to an average of 12% moisture content by the time of dispatch.
However, care must be taken when product is in merchants care or on site, that the product
remains so.

Panelling
l profiles require certain fixing techniques to ensure durability.
- It is important that the following steps be taken to avoid movement of product:

1. Product must be stored indoors and protected from direct sunlight.

2. Seal all around before fixing.

3. Fix by face nailing using adequate nails and glue to all fixing surfaces. (Secret nailing may
not be sufficient to stop all movement of product).

4. Stain, polyurethane or paint.

PurePine
l will provide whatever product the merchant specifies. However, no liability will be
taken for incorrectly specified product.

3
 PurePine Treated and Preprimed Products

PurePine treated and preprimed products are produced with a high level of care and expertise.

Our aim is to always be in the forefront with technology. We have installed the latest high tech paint
line which provides an outstanding finish.

PurePine uses 100% acrylic paint and PUR glue from Switzerland to ensure that we use only the most
environmentally friendly products. This improves the health of our staff and reduces risk of exposure
to harmful substances to our customers. We are the first in NZ to be approved to treat H3.1 using
water-born methods over solvent based treatments.

We apply a two coat system on all our preprimed products, so no additional primer or undercoat will
be required. Before the second coat of primer is applied, each board passes through a denibber which
smoothes all surfaces and creates a high quality surface finish.

4
 STANDARD STOCK & COMMERCIAL MOULDINGS

2 1 103
3
022 12mm
12mm
18mm QUAD 18mm
BUNGALOW
25mm QUAD BUNGALOW
QUAD

18

4 5 6 7 10

30mm

BEV. CORNICE
28mm 28mm
35mm
BUNGALOW SCOTIA SCOTIA
15
O

19A 15 O
15O
18
8
18
10 19 10 18 10

40mm 40mm
40mm
SINGLE BEVELLED DOUBLE BEVELLED BEV. CORNICE
ARCHITRAVE ARCHITRAVE
15 O

20A 15 O

18
10 20 10 813
60mm 90mm
SINGLE BEVELLED ARCHITRAVE BULL NOSED SKIRTING
15 O

822A 15 O

18 18
10 822 10 22 22A
90mm 60mm 90mm
SINGLE BEVELLED SKIRTING BULL NOSED ARCHITRAVE
24 18 18

10 21
24
25
18 24 24A 18
40mm
BULL NOSED ARCHITRAVE
5

D4S D4S
30mm
D4S
30mm
28A 18

26A 10

40mm
12
30mm 40mm

23
18 28
12 10
26 10
27
D4S D4S D4S D4S
5
10 31
135mm
D4S

10
30 14 COVE
16 COVE

90mm
28mm
D4S
44mm

10
29
60mm

D4S
50

30
25
18 101 101B
725
12
725A
101A
18mm 12mm 25mm 30mm 50mm
ANGLE FILLET ANGLE FILLET ANGLE FILLET ANGLE FILLET ANGLE FILLET

816 8
12 6.5 46 7.5 11 6.5
40mm 30mm 25mm 18mm
D/MOULD D/MOULD D/MOULD D/MOULD

27
42 11 43 11
48 12
4.5 6 6
14 12 14 12 6
20mm
DADO DADO ASTRAGAL
40mm
EAVES MOULD

13B 18 13A 18 13C 18 13D 18

25mm 25mm 30mm 40mm

SCRIBER SCRIBER SCRIBER SCRIBER

9
12
T7 12
T8 6 7
13 10
4 102 4
30mm 18mm 9mm 40mm
BEAD BEAD BEAD SCRIBER

20
16 9.5

326 9
9 6 10 9.5

20mm 16mm
GIB MOULD
PAINT MOULD PAINT MOULD
6
 COLONIAL MOULDINGS
This page subject to availability

96 18

135mm

SKIRT

95 18
94 18

90mm 60mm
ARCH/SKIRT ARCHITRAVE

20 50

18 823A
823 18 18

60mm 90mm
GOVT ARCH GOVT ARCH

18 823B 18

135mm

GOVT ARCH

99

15
91 11
92 7 93
60mm Cover 30mm 22mm 10mm
90mm SCOTIA BEAD BEAD BEAD

7
 This page subject to availability

11 105
66mm

COLONIAL

115
11
106
42mm

COLONIAL 62mm Cover

90mm COLONIAL

11 108 18
114
66mm

COLONIAL 91mm

COLONIAL

11
109 18
113
68mm

COLONIAL 66mm

COLONIAL

18
110
90mm

COLONIAL

18
111
140mm

COLONIAL
8
 PANELLING / SARKING
Available in random lengths & various grades

81

10

90 x 10 TG & V (Cover 81)

128

10

135 x 10 TG & V (Cover 128)

172

10

180 x 10 TG & V (Cover 172)

81

18

90 x 18 TG & V (Cover 81)

128

18

135 x 18 TG & V (Cover 128)

172

18

180 x 18 TG & V (Cover 172)

9
 STANDARD D4S

18 18

65 90

18

113

18

135

18

180

42 42

42 65

10
 42

90

42

135

40

7.5

34

26

4
29

BEAZLEY SILL
Available on special order only

11
 JAMBS
Supplied in 4.2m lengths

135
P/R 3mm

J2 30

10
10

135
P/R 3mm

J8 25

10

10

114

P/R 3mm

J1 30

10

10

96 39

11

P/R 3mm

J6 30

10

10

12
 96 39

9.5

P/R 3mm
J6A
20.5
7

10

73 39
P/R 3mm
10

J4
22

112

P/R 2mm

J9 18

1mm

135
P/R 2mm

J7 18
7
10

13
 CAVITY BATTEN
Available in FJ or solid random lengths

21

45

BATTENS
Available either smooth or Band Sawn face

6 3
6

18

40

10 3
6
18

65

10 3
6
18

90

10 3
6
18

110

14
 FASCIA
H3.1 treated FJ Clear Primed White
Standard 6.0 lengths

135

69 18
7

12 8
15

180

70 18
7
12 8
15

135

71 29

12 8
15

180

72 29

12 8
15

180

73 25

7
4
25 8 20
15

15
 WEATHERBOARDS
Ship Lap profiles available on request

10
3
12
110

61A
COVER

140

3
12

12
110

61A
140
COVER
18

18

93
12

8
18

16
 50 85

9.5
67 18

25
Cover 110

50 130

68 18
9.5

Cover 155 25

17
 WINDOW REVEALS
Available in 5.4m and 6.3m lengths. Clear grade supplied in random lengths.

125
P/R 2mm

18.5

8
12 13

GROOVED NOT GROOVED CLEARS GROOVED

92 92 92
107 116 116
116 125 180
125 140
132 180
140
180

Other sizes may be available on request.

18
 PurePine would like
to thank you
for your valued custom

Main Road, Te Puke Phone: (07) 573-9163 Fax: (07) 573-4189

P.O. Box 41 Te Puke, Bay of Plenty 3071, New Zealand