Operating and Service Manual

RO-MP-2 500x400
2000 v.1

PACKAGING TECHNOLOGY EN ISO 9001

70 100 M 745

EAM-MOSCA Corp.
RO-MP-2 1- 1
CONTENTS RO-MP-2

A. INTRODUCTION
1. Introduction and Safety Procedures . . . . . . . . . . . . . . . . . . . . . . 1.6 - 1.16
Application Principles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.8
Machine Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.8
Machine and Operating Elements . . . . . . . . . . . . . . . . . . . . . 1.9
General Safety Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.10
Safety Regulations for Specific Operational Phases . . . . . . . 1.11
Precautions Against Particular Hazards . . . . . . . . . . . . . . . . . 1.12
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.13
Safe Operating Principles . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.15
Description of Safety Arrangements . . . . . . . . . . . . . . . . . . . . 1.16

2. Operating and Technical Information . . . . . . . . . . . . . . . . . . . . . 2.1 - 2.12

Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2
Electrical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3
Component Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4
Operating and Functional Description . . . . . . . . . . . . . . . . . . 2.6
Strap Spool Installing and Threading . . . . . . . . . . . . . . . . . . . 2.8
Sequence of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.10
Sealer Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.11

3. Maintenance and Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 3.1 - 3.16

Preventive Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.1
Maintenance and Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . 3.2
Sealer Position Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . 3.4
Track Slide Plate Position . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5
Solenoid Adjustments ME 2209 & ME 2136 . . . . . . . . . . . . . . 3.6
Heater Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.7
Knife Press-Bar Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8
Tension Relief Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.9
Detailed Description of Strap Threading Process . . . . . . . . . . 3.10
Troubleshooting List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.12

4. Shipping Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1 - 4.2

Shipping Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1

RO-MP-2 1- 2
CONTENTS RO-MP-2

• WHEN REQUESTING SERVICE OR

REPLACEMENT PARTS

Included in this manual are assembly drawings with

complete replacement parts lists. When requesting
service please refer to the identification plate (detail at
right), that is found on or near the electrical
component box.

1. Contact EAM-MOSCA technical service department. MODEL # SERIAL #

2. Give the Model #, Serial # and Year.

VOLTAGE
3. Give part number and complete description from the
parts list.
YEAR

B. PARTS IDENTIFICATION
Main Shaft Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
1620-0110-00 4/14/1997

Cam Shaft Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4

1620-0111-00 12/9/96

Upper Slide Plate Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

1620-0120-00 4/7/1997

Sealer Knife-Gripper Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8

0101-013000-16 8/15/1997

Sealer Right Gripper Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10

0101-0130-17 8/21/1997

Sealer Left Gripper Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12

0401-0130-01 8/21/1997

RO-MP-2 1- 3
CONTENTS RO-MP-2

PARTS IDENTIFICATION (CONT'D)

Sealer Knife & Gripper Bars Assembly . . . . . . . . . . . . . . . . . . . . 5-14
1601-013000-16 3/5/1999

Sealer Housing Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-16

1620-0140-00 4/14/1997

Heater Assembly - 24V DC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18

0901-0160-00 5/22/1996

Strap Feed Pull-Back, Tension Assembly . . . . . . . . . . . . . . . . . . 5-20

1699-016900-00 9/26/1997

Heater Arm Assembly - 24V DC . . . . . . . . . . . . . . . . . . . . . . . . . . 5-24

2601-0170-00 8/24/1996

Slide Plate Lever Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-26

1620-018000-00 10/28/1996

Caster Frame Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-28

500 1620-021000-00 6/18/1998

Foot Pedal Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-30

500 1620-0220-00 12/20/1995

Side Panels & Rear Cover Assembly . . . . . . . . . . . . . . . . . . . . . . 5-32

500 1620-0230-00 1/30/1998

Front Door & Extension Cover Assembly . . . . . . . . . . . . . . . . . . 5-34

500 1620-024000-00 6/3/1997

Table Plate Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-36

500 1630-0250-00 5/29/1996

Center Frame Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-38

500 1620-0260-00 11/27/1996

Dispenser Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-40

1601-0310-00 10/6/1997

RO-MP-2 1- 4
CONTENTS RO-MP-2

PARTS IDENTIFICATION (CONT'D)

Dispenser Support Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-42
1620-032000-00 6/17/1996

Accumulator Fill Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-44

1620-0710-00 2/19/1997

Accumulator Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-48

500 1620-0730-00 6/19/1997

Outer Strap Track Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-50

500/400 1621-0810-00 9/29/1997

Inner Strap Track Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-52

500/400 1621-0820 5/31/99

Strap Frame Cover Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-56

500/400 1621-0830-00 11/21/97

Strap Track Opener Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-58

500/400 1621-0840-00 1/30/96

Fan Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-60

1620-0850-00 7/7/97

Electrical Components Assembly . . . . . . . . . . . . . . . . . . . . . . . . 5-62

1620-1100-00 12/3/97

Control Panel Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-64

1620-1130-00 8/27/97

Support Frame Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-66

500/400 1621-1401-00 2/12/1998

Double Compactor Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-68

500/400 1621-1501-00 1/04/1999

Photo Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-72

1511-0090-00 4/6/99

RO-MP-2 1- 5
INTRODUCTION & SAFETY PROCEDURES

APPLICATION PRINCIPLES

• An automatic strapping machine for bundles from sizes 15.7" x 11.8" (390mm x 290mm)
to 65" x 39.4" (1640mm x 990mm).

• Best suited for all types of packages as in, printed materials, cartons, etc.

MACHINE DESCRIPTION

• Operator controlled strapping machine for polypropylene strapping.

• Light weight - operator friendly.

• Operator initiates strapping cycle by pressing foot switch pedal.

• Simple, safe, reliable, easy operating and handling.

• Processes cost-effective and environmentally friendly strapping.

• Strap tension electronically variable.

• Automatic strap loop ejection.

• Automatic strap end eject.

• Quick strap spool exchange.

• High cycle rate.

• Electronic heater temperature control.

• No wear, one piece, cam controlled strap track.

• Energy saving drives.

• Completely self-contained and portable.

• 2 Swivel casters with brakes for solid positioning and 2 fixed casters for stability.

• Strap width: 5mm fixed, 6-12mm adjustable.

RO-MP-2 1- 6
 INTRODUCTION & SAFETY PROCEDURES
MACHINE AND OPERATING ELEMENTS

10
2

17

7
6

11
5

16 15
9
14 8

13

12

1. Machine Frame 12. Main Switch

2. Strap Track Frame 13. Indicator - Machine On - (Optional Photo Control
3. Front Table Switch)
4. Rear Table 14. Weld Temperature Indicator
5. Roller Casters with Brake 15. Illuminated Push Button - Soft Tension
6. Dispenser Cover 16. Potentiometer - Tension Adjustment
7. Strap Spool 17. Safety Warning Labels
8. Foot Pedal
9. Roller Caster
10. Control Panel
11. Door Knob

RO-MP-2 1- 7
INSTRUCTION & SAFETY PROCEDURES

GENERAL SAFETY INSTRUCTIONS

Key Rules
• Before start-up, read the operating and safety instructions.

• Always keep the operation instuctions within easy reach at the side of the
machine/system.

• Observe the maintenance schedules specified or described in the operating instruc-

tions.

• The machine is built in accordance with state of the art technology and the accepted
rules of industrial safety. Yet, danger to life and limb of the operator or third persons,
as well as damage to the machine and other resources, may still occur.

• Operate this machine/system only while it is in perfect condition and in

accordance with the specifications contained in this manual.

• Be aware of hazards and safety issues and adhere to these operating instructions.

Immediately correct any malfunction that could prove detrimental to

safety, or have someone else correct it.

Organizational Measures
• In addition to the operating instructions, observe and teach generally applicable legal
and other binding regulations for the prevention of accidents and for the protection of
environment.

• All operating personnel must wear protective hair covering to contain long hair; no
loose clothing or jewlery, including rings, may be worn. Injury may result from getting
caught or pulled into the machinery.

• Whenever necessary, or as required by regulation, use personal protective gear.

• Observe all safety and warning labels on the machine.

• Maintain all safety and warning labels on the machine in legible condition.

• Do not let personnel with general training operate the machine/system, except under
the constant supervision of an experienced operator.

• Any work on electrical components of the machine/system may be performed only by

a qualified electrician or by trained personnel under the direction and supervision of
a qualified electrician and in accordance with applicable electrical codes.

RO-MP-2 1- 8
 INTRODUCTION & SAFETY PROCEDURES

SAFETY REGULATIONS FOR SPECIFIC OPERATIONAL

PHASES

• Refrain from any work practice that may be unsafe.

• Make sure that the machine/system is operated in safe and good working order.
Do not operate the machine/system, unless all protective and safety devices,
such as removable machine guards, emergency shut-off switches, and
vacuum systems, are in place and in working order.

• At least once during each shift, you should check the machine for any external
damages and defects. Any changes (including changes in performance) must
promptly be reported to the competent department/person. If necessary,
immediately stop and secure the machine.

• In case of a malfunction, the machine/system must be stopped and secured immedi-

ately. Promptly correct the malfunction or have it corrected.

• Before you put the machine/system in operation, make sure that no one is put at risk
by the machine during start-up.

• Inform operating personnel before you begin to perform any special or maintenance
work. Designate a supervisor.

• If necessary, clear and secure a space around the area where maintenance is being
performed.

• Always tighten any screw connections which were loosened during maintenance
and repair.

• Should safety devices have to be dismantled during set-up, maintenance or repairs,

reassembly and inspection of the safety devices must ensue immediately after
completion of such maintenance and repair work.

• Provide for the safe and environmentally friendly disposal of operating and auxiliary
materials, as well as spare parts.

• Before moving a machine, always check that all accessories are securely stored.

• Discontinue any work practice that could destabilize the machine.

• Keep off conveyors and/or table tops..

RO-MP-2 1- 9
INTRODUCTION & SAFETY PROCEDURES

PRECAUTIONS AGAINST PARTICULAR HAZARDS

Electric Energy
• Use only original fuses with the specified amperage! If a breakdown of the electrical
power supply should occur, the machine must be shut down immediately.

• Work on any electrical system or equipment, may be performed only by a qualified

electrician or by trained personnel under the direction and supervision of a qualified
electrician and in accordance with electrical codes.

• If so specified, machine and system components that are to be inspected,

maintained or repaired must be switched to zero voltage. Any such disconnected
components must first be examined for voltage leaks, then grounded and shorted,
while adjoining voltage carrying components must be insulated.

• The electrical equipment of the system/machine must be inspected/tested regularly.

Defects, such as loose connections or damaged cables must be eliminated.

• Should it become necessary to perform work on live components, a second person

must be added to work the emergency shut-off switch or the master switch. Close
off the work area with a red and white chain, and put up a warning sign.
Use only insulated tools.

• When working on high voltage units, disconnect from voltage, ground power supply
cable and short components, such as capacitors with a grounding rod.

• Carefully remount and refasten any components that were disconnected during
transport before returning the machine to service.

• Even minor changes in location require that the machine or the system be
disconnected from each external energy source.

• Before the machine is returned to operation, it must be properly reconnected to its

power source.

Lockout feature on Main Switch Q1 for safe work environment during

maintenance.

Q1

Currently in the
off position.

Lockout Feature
Attach padlock or
taglock at this point.

Main Switch Detail

RO-MP-2 1- 10
 INTRODUCTION & SAFETY PROCEDURES

SAFETY INSTRUCTIONS

The following list of safety instructions must be read before operating the
strapping machine or the strapping system.

Miscellaneous Instructions
• Please observe the accident prevention regulations as well as the safety and
protection
recommendations of the trade or professional associations.

• The machine may only be used in accordance with regulations.

• If safety changes should occur in the machine/system or its performance, the

machine/system must be stopped immediately and the competent person/depart-
ment must be informed of the problem.

Operation
• Machines may only be operated by trained personnel.

• Training of the customer's operating personnel is available by EAM-MOSCA

customer
service.

• The hazard zone is off limits.

• Keep off conveyors or table tops.

• Keep all safety and hazard warnings on the machine/system in legible condition.

• Do not reach into a machine that is running.

• Never step into or under lifting devices.

• After closing time, always shut the machine down by turning the main switch off.

Safety Devices
• Emergency-off switches must never be by-passed or deactivated.

• Safety devices, not included in the delivery, such as protective grids, must be
installed by the customer in coordination with the competent employer's liability
insurance association.

• Do not undertake any alterations, additions or modifications to the machine/system

that could affect safety without authorization from the supplier. This also applies to
the installation and the adjustment of safety devices and safety valves and to any
machining of load-bearing parts.

RO-MP-2 1- 11
INTRODUCTION & SAFETY PROCEDURES

SAFETY INSTRUCTIONS (CONT'D)

• Do not operate the machine/system unless all protective devices and security
features, such as removable protection devices and emergency-off devices are in
place and functional.

• If safety devices should have to be dismantled during set-up, maintenance, or

repairs, reassembly and inspection of the safety devices must ensue immediately
after completion of such maintenance and repair work.

The following list of safety instructions must be read before operating the
strapping machine or the strapping system.

Repair
• Before any tune-up or repair work can be performed, the machine must be
disconnected from the mains and secured against unauthorized reconnection.

• Tools and single components should not be placed on or in the machine.

• When replacing any parts of the system, components and larger units must be
carefully attached to hoisting equipment in a way that precludes any hazard.

• Use only suitable and technically sound hoisting equipment as well as lifting
devices with sufficient carrying capacity.

• Never stand or work under suspended loads.

• Components must meet the manufacturer's technical specifications. This is

guaranteed when using genuine replacement parts from the manufacturer.

• Hydraulic and pneumatic installations may only be worked on by personnel

specifically trained and experienced in the use of hydraulics and pneumatics.

Electrical Equipment
• Work on any electric installations of the machine/system may only be performed by
a qualified electrician or by trained personnel under the direction and supervision of
a qualified electrician and in accordance with electrical codes.

• Machine/system components undergoing maintenance or repairs must be

disconnected from their power source and closed off.

• The electrical equipment of a machine/system must be inspected/tested regularly.

Defects, such as loose connections, damaged cables, and defective devices must
immediately be eliminated.

• If work needs to be done on live components, a second person must be added to

work the emergency-off switch or the master switch.

• Close off the work area with a red and white safety chain and put up a warning sign.
Use insulated tools only!

RO-MP-2 1- 12
 INTRODUCTION & SAFETY PROCEDURES
SAFE OPERATING PRINCIPLES

Operate this machine with polypropylene strap only. Using other strapping
can cause health risk.

S1
2

S2

CAUTION!
Risk of burn injury
in heater area.

• The pinch points are covered with the table top and in front with the door. Sides and
rear have fixed panels.

• Lifting the table (1) or opening the door (2) 3-5mm, releases the safety interlock S1
and S2, respectively, which prevents cycling the machine.

• When moving the machine on level ground, make sure to release both caster brakes
to position the machine.

RO-MP-2 1- 13
INTRODUCTION & SAFETY PROCEDURES

DESCRIPTION OF SAFETY ARRANGEMENTS

• With power on the machine and main switch Q1 on, the machine will be operational
after approximately 1 minute of heat-up time.

• The machine operation is stopped by any of the following:

- Opening the front door.
- Opening the front table.
- Blown fuses.

• For machines with the press option;

- If a safety circuit is interrupted, the press returns
to the up position.

• The heater is on as long as the main switch Q1 is on 1.

RO-MP-2 1- 14
OPERATING AND TECHNICAL INFORMATION

RO-MP-2 2- 1
 OPERATING AND TECHNICAL INFORMATION
TECHNICAL DATA
A B

H G

F
E

Sealer Center
C (C1)

I
D (D1)

Work Area Width

Strap Weld :
Thermal mm 400 500 600 800
Strap Width :
5&6mm or 7-12mm
A 875 875 875 875
Strap Tension :
Infinitely variable or Soft Tension
Strap Coil :
200mm Dia. and 280mm Dia. B 590 590 590 590
Strap Spool :
Up to 6000m / 23,000ft.
Weight :
135kg - 145kg
C 1180-1285 1280-1385 1380-1485 1480-1585
Electric Power :
110V / 60Hz C1 1105-1210 1205-1310 1305-1410 1405-1510
230V / 50Hz
240V / 50Hz D 815-920 815-920 815-920 815-920
400V / 50Hz D1 740-845 740-845 740-845 740-845
Noise Emission : 79db (A) Measured to
DIN 45635 Part 27 E 300 400 500 600
F 400 500 600 800
Dimensions C1 and D1, are for low frame
machines. G 185 185 185 185
H 110 110 110 110
I 405 405 405 405
Strap Cycle per Minute
ca. 50 48 46 44

RO-MP-2 2- 2
 OPERATING AND TECHNICAL INFORMATION
ELECTRICAL DATA

Electrical Power Line: 1~ + N + PE

Power output: 0.5 kW
Load Amperage: 2.4 Amp.- 4.8 Amp.
Voltage: 230V / 115 V.
Frenquency: 50 / 60 Hz
Current type: 1 AC

Electrical Power Requirement

• The supply line for the machine must be a minimum 3 wire. 1.5mm (14AWG) 15A.

• The line protection fuse shall be not more than 15 Amp.

• The line connector shall be a grounded 3 pole (1~ + N + PE).

• The machine shall be operated only in a dry environment.

Do not remove sticker with

program number on it. It
will erase the program.
EEPROM DETAIL

WINDOW

SOCKET DETAIL

NOTE: The notch in EEPROM and Socket should be on the same side
when inserting chip.

CAUTION: Pins on EEPROM can bend easily.

RO-MP-2 2- 3
 OPERATING AND TECHNICAL INFORMATION
COMPONENT LAYOUT

Control Panel Detail

on the following page.

St

B11

M5 M1
M3

M4
M2 B1

S1

B13.1 Y9 Y10
Y10.1
B7 B13
S2

S6

B6

B8

Y4

Page 1 of 2

RO-MP-2 2- 4
 OPERATING AND TECHNICAL INFORMATION
COMPONENT LAYOUT

B1 Proximity Sensor - Strap Feed Stop

B6 Proximity Sensor - Foot Switch, Strap Feed,
Cycle start Sealer to Home Position.
B7 Proximity Sensor - Strap End Sensing
B8 Proximity Sensor - Accumulator Fill
B11 Proximity Sensor - Strap Track and Slide Plate Closed
B13 Proximity Sensor - Sealer Home Position
B13.1 Proximity Sensor - Sealer Stop Position 1-2-3
S1 Safety Switch - Front Table
S2 Safety Switch - Front Door
S5 Illuminated Push Button - Soft Tension
S6 Push Button - Dispenser Brake Release
H1 Selector Switch - Photo Control Power On
H2 Indicator - Machine On
Q1 Main Switch
Y4 Dispenser Brake
Y9 Solenoid - Strap Threading
Y10 Solenoid - Strap Tension
Y10.1 Solenoid - Strap Pull-Back
M1 Strap Tension Motor
M2 Sealer Motor
M3 Accumulator Motor
M4 Strap Drive Motor
M5 Exhaust Fan
R1 Potentiometer
V1 Weld Temperature Indicator
St Electrical Enclosure

R1 R1 S5
S5

V1 V1

H2 H1

Q1 Q1

Control Panel Detail Control Panel with Photo Control Option

Page 2 of 2

RO-MP-2 2- 5
OPERATING AND TECHNICAL INFORMATION
OPERATING AND FUNCTIONAL DESCRIPTION
R1 S5
V1

H2

Q1

Control Panel Detail

St

B11

M5 M1
M3

M4
M2 B1
S1

B13.1 Y10
Y9
Y10.1
B7 B13
S2
S6

B6

B8
Y4

1. Turn on the main switch (Q1). This sends power to the heater and
control circuit.

2. After approximately 1 minute of heating time, from initial start-up, the

welding unit is ready for operation indicated by steady Weld Temperature
Indicator light. (V1).

3. Install the strap spool and thread the strap as indicated in the threading
diagram. (see page 2.8 & 2.9)

RO-MP-2 2- 6
 OPERATING AND TECHNICAL INFORMATION
OPERATING AND FUNCTIONAL DESCRIPTION (CONT'D)

4. Operate the foot switch, the strap will be fed into the strap track until
proximity switch B1 is activated.

5. Place the package to be strapped on the table over the strap line and
top slide plate.

6. When foot pedal is operated a second time, the sealer motor starts up
until proximity sensor B13.1 is deactivated. The strap pull-back starts, until
the selected tension is reached.

7. After the welding cycle is completed, the package is strapped. The strap
track frame closes and the sealer moves into home position via. proximity
sensor B13. The strap is automatically fed through the strap track and into
sealer.

8. Remove the package from the machine. If the foot switch is operated again,
a new strap cycle will begin.

NOTE: Refer to page 2.6 for the Component Layout.

RO-MP-2 2- 7
OPERATING AND TECHNICAL INFORMATION
STRAP SPOOL INSTALLING AND THREADING
Threading Components
A Main Switch K Idler Roller
B Machine On Indicator L Strap End Sensor Guide
C Weld Temperature Indicator M Feed Roller
D Illuminated Push Button - Soft Tension N Pressure Roller
E Strap Tension Potentiometer O Strap Guide Mark
F Foot Pedal P Strap Threading Gate
G Dispenser Knob Q Tension Drive Roller
H Dispenser Cover R Tension Pressure Roller
I Accumulator Fill Sensor S Strap Drive Roller
J Dispenser Brake Release T Pressure Roller Lever
U Pressure Roller

D C B A
E

N M L
O

R Strap
S
T
N M
U
P Detail of Strap

O K

L
J

G
I
Bend the strap tip down
H before inserting.

RO-MP-2 2- 8
 OPERATING AND TECHNICAL INFORMATION
STRAP SPOOL INSTALLING AND THREADING (CONT'D)
Strap Threading
DO NOT TURN POWER OFF DURING THE THREADING PROCESS.
1. If machine is in threading position (strap track is open) proceed to step 3.

2. To set threading position, the machine must be cleared of any existing strap in the
threading areas. To remove strap, cut strap between (L) and (K). Open the
accumulator door, pull strap ONLY towards the left side wall of the machine. Not
forward, or to the right where the strap will jam between the drive rollers. After strap
is removed, close door and press foot pedal once. The track will open and the feed
motor will turn.

With the machine in the threading position (the strap track will be open), follow these
steps to install and thread a new spool of strap:

3. Open the front door of the machine.

4. Turn knob (G) counterclockwise, and remove dispenser cover (H).

5. Remove the old spool and all cardboard inserts and discard.

6. Place the new strap spool on the dispenser making sure that it unwinds in the
counterclockwise direction.

7. Replace the dispenser cover (H) and tighten knob (G).

8. Remove all adhesive tape strips and other fastening material.

9. Press and hold push-button (J) to release the dispenser brake and unwind about 18
inches of strap from the spool.

10. Thread the end of the strap behind roller (K), and into strap threading guide (L).

11. The strap threading gate (P) will close automatically when the strap end passes
through strap threading guide (L).

Note: If threading gate (P) does not close when the strap passes guide (L) or opens during the
threading operation (the threading operation is limited to 30 seconds), remove the strap, close
the front door and depress the foot pedal twice. Continue with step 10. If the machine will not
enter the strap threading position, contact your supervisor for assistance.

12. When the strap presses against the pressure roller (N), turn the feed roller (M)
clockwise (while continuing to apply pressure to the strap) and feed strap around
until the end appears somewhere in the red zone indicated by (O).

13. Close and secure the front door and depress the foot pedal.

14. Strap will then be fed into the feed rollers and then into the accumulator. When the
accumulator is full, as indicated by sensor B8 (I), strap will feed around the track.

Note: A detailed description of the strap threading process is given on pages 3.10 & 3.11,
along with inputs and outputs for strap threading troubleshooting

RO-MP-2 2- 9
OPERATING AND TECHNICAL INFORMATION
SEQUENCE OF OPERATION

1. Position the bundle to be strapped over the center of the top slide plate.

2. Operate the foot pedal to start the first part of the sealer cycle, feeding the strap from
the accumulator through the strap track and into the sealer.

3. Operate the foot pedal a second time to start the sealer. The right gripper will raise to
clamp the top piece of strap, the strap track is opened, and the strap is pulled around
the bundle. The unused strap is fed back into the accumulator.

4. When the strap tension is reached, the left gripper clamps the strap end and the
lower slide plate moves back to allow the heater to move between the strap ends.

5. As the knife-bar moves up, it cuts the strap, then presses the heater tongue between
the strap ends melting the surfaces.

6. The knife-bar drops down, and the heater pulls out. The knife-bar then moves up a
second time pressing both molten surfaces together to form a weld.

7. Once weld cooling is completed, the knife-bar and both grippers drop down. The top
slide plate moves back ejecting the seal. The strap track closes and the slide plates
move forward completing the cycle.

8. This completes the sealer cycle, with a strapped package. Once the strap track is
closed, the strap is automatically fed into the sealer activating sensor B1 indicating
the strap and sealer are ready.

Note: The machine has an automatic strap eject system. When the strap spool is
empty, the machine ejects the remaining strap from the accumulator out of
the strap track and onto the table.

RO-MP-2 2- 10
 OPERATING AND TECHNICAL INFORMATION
SEALER SEQUENCE
Operating the Sealer Manually
Since the sealer unit controls the strap tensioning, gripping, cutting, and welding of the
strap, at times it is necessary to check the individual movements. All movements are cam
operated-spring return, on one main cam shaft.
• To check proper operation of all sealer components, the operator may turn the sealer
unit by hand. In order to do this, perform the following 2 steps, then follow the below
sequence to troubleshoot machine.
1. Turn off the main power switch.

2. Turn knurled knob on sealer drive motor M2 in the direction of arrow indicated.

Sealer Sequence
1. At sealer neutral stop (home position), sensors B13 and B11 are activated, indicator
lights are on.

2. The first action in the sealer is that the right gripper bar is lifted, clamping the top strap
end against the top slide plate. Check strap to see if it is clamped tight.

3. The strap track opens to allow the strap to be pulled out. Make sure the track moves
freely.

4. When the track is almost fully open, the sealer continues to drive until pullback position,
sensor B13.1 is activated.

5. In pullback position, solenoid Y10.1 and strap motor M4 are activated to initiate pullback
of the strap.

6. When pullback is completed, final tension is applied to the strap. Motor M1 and
solenoid Y10 are activated.

7. When the tension cycle is complete, the left gripper bar moves up to clamp the bottom
strap against the top plate (check to see if strap is clamped tight).

8. At the same time, the heater begins to move into the weld area.

9. When the bottom strap is clamped, the center knife-press bar starts to move up while
the heater continues to move in between the top and bottom strap.

10. The lower slide plate is pulled back at the same time the heater moves into the sealing
area. (The heater tongue should not contact the lower slide plate.)

11. As the knife-press bar moves up, it cuts the bottom strap and then presses the two
strap ends firmly against the heater. Make sure the straps are clamped tight against
the top plate.

12. After a short time, the knife-press bar moves down about 1/4" to allow the heater to
move out. As the heater clears the bar, the knife-press bar moves up to press the two
molted surfaces together to form a weld.

Note: It is very important that the knife-press bar moves down (pulled by the spring). If the
bar sticks and can't free the heater tongue, it pulls the bottom strap out and when the
bar comes up, the strap ends can be misaligned causing a break in the weld.

RO-MP-2 2- 11
OPERATING AND TECHNICAL INFORMATION
SEALER SEQUENCE (CONT'D)

13. At the end of the seal and cooling time, the three bars are pulled down by their
springs. Then the top slide plate is pulled back releasing the strap against the
bundle.

14. The top and lower slide plates move forward and the track closes, activating sensor
B11.

15. The sealer continues to drive until sensor B13 is activated, stopping the sealer shaft
movement. (Home Position)

16. With sensors B11 and B13 activated, the strap drive motor M4 is activated to feed
strap around the track.

17. Strap is fed around the track until sensor B1 is activated. At this point, the machine
is ready to cycle.

SEALER UNIT

E
A

B D

A Top Slide Plate with Lower Slide Plate

B Left Gripper (clamp)
C Knife-Press Bar
D Right Gripper-Cutting Edge
E Knife

RO-MP-2 2- 12
 MAINTENANCE AND TROUBLESHOOTING
PREVENTIVE MAINTENANCE
1. Check all electrical plug-connections.

2. Make sure the supply line voltage matches machine voltage.

3. Check the P.C. board connections. Reseat the plugs periodically.

Do not force PC Board connectors when re-installing.

4. Clean the exhaust fan periodically.

5. Machines equipped with plug in relays, reseat relays periodically.

6. Check all proximity sensors; the mounting, the gaps, and clean when needed.

7. Check the temperature control setting. The heater temperature should be checked at the
heater tongue tip at 260º C (500ºF). If needed, adjust the temperature with the
potentiometer on the controller R1.

8. Check all screws every 6 months and tighten when necessary.

9. Clean daily with an air hose or brush:

• strap feed roller assembly
• strap guide (with track open)
• top and bottom slide plate assembly
• grippers and knife-press bar
• accumulator feed rollers
• accumulator chamber

10. Clean out the inner strap track area periodically and lubricate the linkages with light oil.

11. Make sure to clean and lubricate regularly as per instruction. (See page 3.3 & 3.4)

12. After the initial 500 hours of operation and every 100-150 hours of operation there after,
perform the following procedures.
• Clean and lubricate top and bottom slide plates. Check the bumper ring, washer
and spring. Replace if worn.
• Check B11 strap sensor finger and adjust if loose.
• Remove the strap track front cover. Lubricate the strap track opener and strap
track swing linkages.
• Clean and lubricate grippers and knife-press bars; remove the slide plate assembly,
pull out the grippers and knife-press bar. Clean thoroughly, especially the
corners of the casting slots. Check wear marks and make sure the cam rollers are
free and lubricated.
• Clean and lubricate slide plates and guides.

13. Work on the electrical control system must only be done by qualified personnel.

When cleaning the dust from the machine, don't hold the air nozzle directly on
bearing seals-shield or knife-gripper bar sliding surfaces. You may force the
dust into the bearing surface. Make sure to lubricate the cleaned areas.

RO-MP-2 3 - 1
MAINTENANCE AND TROUBLESHOOTING
MAINTENANCE AND LUBRICATION

Maintenance
• With proper maintenance, the strapping machine will perform at its optimum level
under standard operating conditions.

• Keep the strap drive and sealer clean and free of paper, dust and strap
pieces.

• Clean out the following with a brush or blow out with air weekly;
- The Accumulator and Accumulator Fill Drive .
- The Strap Guides.
- The Heater.
- The Gripper Areas.

Lubrication
• The sealer gripper and slide plates should be lubricated weekly with light,
clear, non-gumming oil.

• Track opener and track swing linkages should also be lubricated weekly.

MAINTENANCE INSTRUCTIONS

1. The temperature of the heater is measured on the heater tongue and should
read 260°C or 500°F. Adjustment is made with the potentiometer on temperature
control N1, found in the electrical enclosure box.

2. The exhaust fan must be cleared periodically.

3. Check the proximity sensors and photo controls for proper mounting and
adjustment.

4. Keep the inside of the machine clean and look for possible damage to cables
and switches.

5. Make sure only properly trained personnel (Electrician) will work on the
control system.

RO-MP-2 3 - 2
 MAINTENANCE AND TROUBLESHOOTING
MAINTENANCE AND LUBRICATION

• Lubricate weekly with small doses: between grippers and knife-press bar, slide plates,
and strap track assembly bushing.
• Use only, light-clear oil.
• All other assemblies are lubricated for life.
• Keep the strapping machine, especially the strap guides and sealer, in clean
condition.
• Make sure that the lubricant does not get into any areas the strap travels through.
• Make sure to place slide plate lever pin in between forks of slide plate properly.
• Make sure sealer sensor flag(s) are not loose.
• Make sure upper slide plate shoulder bolt is not loose.
• Make sure gripper springs are not worn out.

RO-MP-2 3 - 3
MAINTENANCE AND TROUBLESHOOTING
SEALER POSITION ADJUSTMENT

Note: Sealer moves counterclockwise through positions 1-3, looking at the

sealer from the left side.

"X"
View "X"

A
C

B13

B13.1

M2

A Track Opener Cam

B Sealer Position Pointer (points to dimple in cam) (Home position timing mark).
C Sealer Position Sensor Flag
B13 Sealer Home Position Sensor
B13.1 Sealer Tension Position and Weld Cooling Position
M2 Hand Wheel Sealer Motor

Sealer Home Position

1. The sealer home position is signaled by proximity sensor B13. The right gripper is at
its lowest position possible. The dimple on track opener cam A is lined up with pointer
B.
• Adjust the position by moving the B13 sensor flag.

2. The strap pull-back position is signaled by proximity sensor B13.1. The correct
position is when the strap track is fully open and the heater starts to move toward the
strap.
• Adjust with the first sensor flag of B13.1.

3. The weld cooling position is also signaled by sensor B13.1. The correct position is,
after the heater moves out, and the center knife-press bar moves up fully.
• Adjust with the second sensor flag of B13.1

RO-MP-2 3 - 4
 MAINTENANCE AND TROUBLESHOOTING
TRACK SLIDE PLATE POSITION
Strap Sensor Detail
Sealer Housing
Set Screw NT 891
Proximity Switch B1/S1

Post

Top View
Side View
Note: Make sure to install the
spring with the smaller diameter
end against the pin shoulder. 1mm Gap between
Strap Sensor Pin Slide Plate & Switch
Actuator
Switch Actuator
1

2
5

4
Track
3

Sealer Detail 6

B1/S1

B11

Sealer Components
1 Strap Sensor Actuator
2 Top Slide Plate
3 Lower Slide Plate
4 Strap Sensor Spring
5 Strap Sensor Pin
6 Track Position Bracket
B1/S1 Strap Sensor Proximity Switch
B11 Slide Plates and "Track Closed" Proximity Sensor

Adjustments
1. Adjust the strap sensor (B1/S1) to have light "on" when the strap sensor flag (1) is
pushed toward the sensor, 2/3 of total travel distance.

2. Adjust the track position bracket (6), to have the light of (B11) off when the strap
track is open approximately 1/8" and the slide plates are fully closed.

RO-MP-2 3 - 5
 MAINTENANCE AND TROUBLESHOOTING
SOLENOID ADJUSTMENTS Y10 & Y10.1 ME 2209 (High Tension) & ME 2136

A - Feed Spring
B - Pressure Lever
C - Hex Nuts
D - Socket Cap Screw
F - Pull-Back Spring
G - Hex Nuts

D 1.0mm

B
Y10 Y10.1
Tension Pull-Back
A
60V / DC 24V / DC
40% ED 100% ED
white black
red green

C
Push solenoid rod into the G F
end position manually.

The Sealer must be in the home position with strap threaded in.

1. Feed - Adjust spring tension (A) to provide enough roller pressure to feed the strap,
using socket cap screw (D).

2. Pull-back - Set pull-back pressure with spring (F) by adjusting the double lock
nuts (G). The strap should pull around the top plate in the time set with S7.
(without strap hangup)

Note: The tension adjustment of the solenoid is made with the solenoid rod pushed fully to
the left as indicated by the arrow.

3. Tension - This adjustment is made with the solenoid plunger fully bottomed out,
push the lever (B) to the left. The solenoid plunger bottoms out. Turn double
lock nuts (C) up against lever (B). Turn the double nuts clockwise an additional 1.5
revolutions.

Note: When pushing the solenoid rod in-fast, the plunger bottoming sound should not be heard.

RO-MP-2 3 - 6
 MAINTENANCE AND TROUBLESHOOTING
HEATER ADJUSTMENTS
Heater
1/16" clearance
Top Plate
1/32" clearance

Lower Plate

Right Gripper
Left Clamp
Knife

Heater Tongue
Top Plate
24V. Heater
1/16" or within
clearance

Mounting Plate

Spring

Hex Nuts

NOTES: In order to adjust the heater to the above shown clearances:

1. Turn the machine power off.
2. Turn the sealer motor using the white plastic hand wheel to bring
the heater into the weld area.
3. Remove the spring.
4. Loosen the hex nuts in the mounting plate.
5. Move the heater into the correct position and tighten the top nut.
6. Turn the sealer motor to bring the heater out.
7. Tighten both “hex nuts” firmly.`
8. Replace the spring.
9. Make sure to check adjustment after tightening the “hex nuts”.

RO-MP-2 3 - 7
MAINTENANCE AND TROUBLESHOOTING
KNIFE PRESS-BAR ADJUSTMENT

Top Plate

Right Gripper

Cutting Edge

Left Gripper
Knife

Knife-Press Bar

To Align knife edge against the Right Gripper:

1. Turn the sealer in reverse, to manually lift the knife-press bar to align both cutting
edges.

2. Loosen the knife screw, then tighten the screw while lightly pressing the knife against
the right gripper. Make sure the screw top is flush with the top of the knife.

RO-MP-2 3 - 8
 MAINTENANCE AND TROUBLESHOOTING
TENSION RELIEF ADJUSTMENT
Detail 1

Strap

2m
m

Detail 2

• To prevent strap end splitting during the strap cut-off, tension roller (A) must be lifted
off the strap before cut-off.

• Turn the sealer to bring the high point of cam (C) to the cam roller (B).

• A 2mm space should be available between rollers (D) and (E) when roller (B) is
pushed down making contact with cam (C).

• The strap should move freely between all rollers with the solenoid (Y10) energized.

RO-MP-2 3 - 9
MAINTENANCE AND TROUBLESHOOTING
DETAILED DESCRIPTION OF STRAP THREADING PROCESS

STRAP EJECTION Refer to page 2.8 for the Strap Threading Diagram.
• The RO-MP-2 machine is equipped with Auto-strap eject function when the strap
spool is empty.
• The machine will automatically recognize the strap spool has run out of strap,
providing the correct Input/Output (I/O) orientation is achieved.

1. During operation of the machine, the accumulator fill sensor (I) will detect a low
amount of strap and activate the accumulator drive assembly (M) and (N). Strap will
be pulled from the strap spool to refill the accumulator chamber as needed. The
machine will sense there is no strap remaining on the spool when the end of strap is
pulled through point (L).

2. When the end of the strap is pulled through point (L) and the strap end actuator flag
has dropped down, the strap end sensor B7 input (E9) will be off and accumulator fill
sensor B8 input (E6) will be on.

3. The strap will then be pulled through the accumulator feed rollers, (M) and (N),
moved into the accumulator chamber, and fed out onto table top area by the strap drive
motor assembly for easy removal.

NOTE: The accumulator fill sensor B8, input (E6), must be on. If sensor B8 is not on, the
machine will not pull strap through the accumulator feed rollers, sensing the
accumulator is full of strap.

STRAP THREADING
• The RO-MP-2 machine is outfitted with a semi-automatic threading assembly.
• To assist the feeding process, a feed gate (P) in the accumulator will drop down to
direct strap through the accumulator to the strap drive. It is important to have the
correct (I/O) orientation and to follow the correct procedure when trying to feed strap
into the machine.
• Before strap threading, the machine must be cleared of any existing strap in
the threading areas. To remove strap, cut strap between (L) and (K), open the
accumulator door and remove all strap. When removing strap from the
accumulator area, pull strap ONLY toward the left side wall of the machine,
not forward.

1. Close swing table top and front access door to ensure all safety switches are
activated, input (E11) on. Due to safety concerns, DO NOT operate the machine
with the safety switches bypassed. If safety switches are bypassed, the strap
threading sequence will not work properly.

2. Turn the main switch (A) on. Do not turn machine power off during the
threading operation. Once the heater reaches operating temperature, the
weld temperature indicator (C) will remain lit.

3. Reset the machine memory by pressing the foot pedal (F) twice. As the machine
memory is clearing, the green strap track will cycle open and close, then re-open
followed by the strap drive motor (M4) running momentarily.

RO-MP-2 3 - 10
 MAINTENANCE AND TROUBLESHOOTING
DETAILED DESCRIPTION OF STRAP THREADING PROCESS
CONT'D
STRAP THREADING CONT'D
4. The (I/O) configuration should be as follows when the machine has completed
resetting memory: sensor B13.1 input (E5), sensor B8 input (E6), N1 signal
input (E10), safety switches S1 & S2 input (E11), and output (A12) should all be "ON",
for threading to work properly.

5. Turn knob (G) counterclockwise, and remove dispenser cover (H).

6. Remove and discard any existing cardboard guide rings and spool tube.

7. Place the new spool of strap on the dispenser holder making sure it unwinds in the
counterclockwise direction.

8. Replace the dispenser cover (H) and tighten knob (G) until it locks into place.

9. Remove all adhesive strips and other fastening material.

10. Push and hold button (J) to release the dispenser brake and unwind about 18 inches
of strap from the top of the spool. Make sure there is no twist in strap during
threading procedure.

11. Thread the end of the strap behind roller (K), and into strap sensor guide (L). The
threading gate (P) will close automatically once strap is inserted into guide (L) by
activating sensor B7, input (E9). If thread gate (P) does not close when strap is
inserted, remove strap from guide (L), close front door and press foot pedal
twice. Machine will run through a memory reset cycle as noted in step 3. ** If
problem with threading gate (P) continues, check if accumulator fill sensor B8, input
(E6) is on, and strap end sensor B7, input (E9) is off.

12. Continue to feed strap until a resistance to strap occurs. Apply pressure to strap
while turning roller (M) and advance strap to red zone (O). If strap threading gate
opens during procedure, strap must be removed from strap end sensor guide
(L), front door closed, and foot pedal (F) must be pressed twice. This will reset
machine and continue with step 11. (The thread gate operation is limited to
30 seconds.)

13. Close and secure front door and press foot pedal (F) once. By operating the foot
pedal, strap will be fed up to the strap drive.

14. Once strap is fed up to strap drive, strap will continue feeding into accumulator
assembly. When accumulator fill sensor B8, input (E6), is off, accumulator will be full
of strap and strap drive motor (M4) will activate and feed strap around green strap
track.

15. Machine should be ready to operate. When machine is ready and sealer is in home
position, the following (Input) configuaration is needed to cycle machine: sensor
B13, input (E1), sensor B11, input (E2), sensor B1, input (E3), N1 signal, input (E10),
safety switches S1 & S2 signal, input (E11), all need to be "ON". Other inputs may
be on, however, the inputs listed above NEED to be "ON" to operate machine.

Refer to page 2.8 for Strap Threading Diagram.

RO-MP-2 3 - 11
MAINTENANCE AND TROUBLESHOOTING

TROUBLESHOOTING LIST

Trouble C au se Remedy

Strap not feeding through track The strap is twisted in the Remove the strap and re-thread
arch. accumulator. according to diagram pg. 2.8.
Make sure no twist exists.

Strap is jammed between the carton Loosen dispenser cover, and free
disc and the spool cover. strap.

Accumulator sensor flag does not Remove all foreign particles from
move freely. accumulator. Make sure the sensor
flag moves freely.

Spool unwinds in the wrong direction. Remove the dispenser cover, and
replace the spool so the strap
unwinds in a counterclockwise
direction. (see pg. 2.8)

Strap feed roller does not advance Clean out upper and lower strap
strap. guides, and adjust feed pressure
roller according to diagram. pg. 3.9

The dispenser brake is too tight. Adjust the brake gap to 0.005 inches
(Check brake by using push button all around.
S6. Dispenser should spin freely
while push button is pushed.)

The top slide plate is not in full Sensor B11 is not on. Clean top
forward posiition. slide plate assembly. Make sure
sensor B11 is actuated 1/8" before
full forward position.

The track is not completely closed. Clean out track assembly. Make
sure sensor B11 is actuated just
before the track is completely closed.

The strap makes contact with the Check the guide pins and bushings.
right gripper. (Home position). The Loosen the bridge screws and adjust
track is too low. the track exit point.

Grippers in sealer do not move down Clean and lubricate properly. Check
with the cams. springs for fatigue.

Strap is pulled back, past the The strap sensor B1 is held "on" by Clean out area. Replace sensor if
feed pull-back roller. the switch actuator flag, or sensor is necessary.
bad.

Right gripper not clamping strap or Check if right gripper and/or cam
strap slips. follower are worn. Check for up and
down movement in the slide plate
assembly.

RO-MP-2 3 - 12
 MAINTENANCE AND TROUBLESHOOTING
TROUBLESHOOTING LIST (CONT'D)

Trouble C au se R emedy

The strap is pulled around the The tensi oni ng roller sli ps on the 1. C heck i f the motor i s turni ng.
bundle, but is not tightening. strap. 2. C heck i f the tensi on solenoi d
i s pulli ng the lever to the left si de.
3. Adjust the tensi on solenoi d.
See di agram pg. 3.6

Thread gate w ill not close. The machi ne has not establi shed C lose all doors and acti vate the
Gate closes w hen; a fault. foot pedal twi ce.
-no strap in accumulator
-B 7 senses no strap
-Strap feed takes longer than B7 sensor actuator i s not movi ng C lean sensor area. Replace
10 seconds and the pow er is freely, and/or B7 sensor i s bad. sensor B7 i f bad.
not off = Fault.
-Turning pow er off after a The solenoi d to gate crank Adjust the two nuts to the ri ght of
fault signal w ill reset the fault. posi ti on i s too low. the solenoi d to allow for a hi gher
crank posi ti on.

Sealer does not move to Safety swi tch s1 and/or S2 not Make sure all tables and doors
home position. operated. (Swi tch loose) are closed to complete safety
ci rcui t.

Sli de plate lever not properly Make sure pi n on sli de plate arm
hooked i nto lower sli de plate. i s i nserted between fork on lower
sli de plate.

Proxi mi ty swi tch B13 loose or Adjust and secure sensor i f

defecti ve. necessary.

Motors do not start up. Plug connecti ons on motor C heck plug connecti ons at
cables are not plugged properly. motors.

Strap i s jammed i n the strap Remove debri s and clean area

gui de. properly. If gui de i s removed,
make sure gui de does not bi nd
wi th movi ng parts when re-
i nstalled.

RO-MP-2 3 - 13
MAINTENANCE AND TROUBLESHOOTING
TROUBLESHOOTING LIST (CONT'D)

Trouble C au se R emedy

Strap w eld breaks apart or The front swi ng table "strap Adjust the swi ng table strap
poor w eld but holding. gui de" i s out of ali gnment. gui de to the strap wi dth.

The kni fe-press bar does not 1. Make sure the kni fe-press bar
move down when the heater moves freely.
moves out from i n between the 2. C lean and lubri cate the bar
heated strap ends. and sli de area, check i f the strap
The lower strap end i s pulled out track contacts the ri ght gri pper
wi th the heater. when the gri pper i s i n i ts up
posi ti on.
3. C heck the roll pi n on the Kni fe
Gri pper assembly to see that i t i s
not hi nderi ng the movement of
the cam roller.

The heater tongue needs 1. Remove heater assembly

cleani ng and the temperature i s when cool and clean wi th fi ne
too low. emery cloth.
2. Be careful not to bend the
heater tongue.
3. C heck heater for defects.

The heater assembly i s too ti ght 1. Make sure the heater

i n the arm pi ns. assembly i s loosely held (not
It cannot center i tself properly bi ndi ng) by the arm pi ns.
between the two straps. 2. Turn the sealer to where the
heater tongue i s clamped
between the kni fe-press bar and
top sli de plate.
3. C heck and make sure the the
heater i s free to ali gn i tself
properly.

The heater arm spri ng i s weak, Replace the spri ng.

does not pull the heater fully i nto
the strap weld area.

1. Temperature control plug i s Plug i n properly. C heck i f

loose. contacts are clean.
2. Temperature control i s Replace i f defecti ve.
defecti ve.

RO-MP-2 3 - 14
 MAINTENANCE AND TROUBLESHOOTING
TROUBLESHOOTING LIST (CONT'D)

Trouble C au se Remedy

Strap cycle not starting. Proximity switch B6 loose or defective. Adjust & secure if necessary. Sensor
B6 should activate when foot pedal is
pressed.

Strap is not threading in. Proximity switch B7 is defective. Replace sensor if necessary.

Sensor flag of proximity switch B7 is Remove debris and clean area.

jammed. Sensor flag should freely drop down
through cover.

Feed-pullback position not adjusted See adjustments on page 3.6

properly.

Threading solenoid Y9 or guide Make sure thread gate moves and

jammed. retracts freely. check position of strap
guide from thread gate to fee pull-back
drive roller.

Machine is not in thread-in position Reset machine and begin strap thread
(operate foot switch). process. See page 2.8 or 3.10 for
more detail.

**For further help, please call the EAM-MOSCA service department.**

RO-MP-2 3 - 15
MAINTENANCE AND TROUBLESHOOTING
NOTES:

RO-MP-2 3 - 16
 SHIPPING PROCEDURE

SHIPPING PROTECTION

A
Lift strap load capacity
shall be 150kg - 300kg each.

Center of Gravity

min. 300mm

• The strapping machine is shipped on a pallet. The machine is lifted on a pallet with a
hoist using lift straps (A). For protection against moisture, the machine is wrapped
inside a plastic foil.

• With straps (B), the machine is fastened to the pallet to prevent sliding.
Use Caution when cutting these straps. Use proper eye protection when cutting.

• Lift straps shall be used to lift the machine off the pallet.

CAUTION: Care should be taken when cutting or disposing of metal strapping.

Wear proper clothing including gloves and safety glasses. Dispose of loose
strapping immediately.

RO-MP-2 4- 1
NOTES:

RO-MP-2 4- 2
PARTS IDENTIFICATION

RO-MP-2 4- 3
PARTS IDENTIFICATION

RO-MP-2 5-1
MAIN SHAFT ASSEMBLY
1620-0110-00 4/14/1997

RO-MP-2 5-2
MAIN SHAFT ASSEMBLY
1620-0110-00
Item Part Number: Description: Qty: Notes:
1 1620-0111-00 Cam Set Assembly Complete 1
10 1620-0110-10 Motor Bracket 1
12 1620-0110-12 Strap Track Cam 1
13 1620-0110-13 Sensor Flag 2
14 1620-0110-14 Hand Adjustment 1
15 1620-0110-15 Sensor Flag 1
16 1620-0110-16 Cam 1
19 2670-0110-19 Coupling 1
20 2670-0110-20 Coupling 1
21 0401-0110-11 Left Bearing Block 1
22 0401-0110-12 Right Bearing Block 1
23 NT 72 Washer 3
26 NT 176 Lock Washer 3
27 NT 74 Lock Washer 5
28 NT 1672 Lock Washer 4
29 NT 7 Snap Ring 2
31 NT 9 ** Bearing 2
32 NT 18 Socket Cap Screw 2
33 NT 76 Socket Cap Screw 5
34 NT 891 Set Screw 2
35 NT 1008 Set Screw 1
36 NT 259 Socket Cap Screw 4
37 NT 872 Set Screw 1
38 NT 475 Hex Screw 3
39 NT 2445 Woodruff Key 1
40 NT 36 Key 1
41 NT 80 Key 1
42 NT 999 Roll Pin 1
43 NT 2222 Lock Washer 2
44 NT 2129B02 Coupling Insert 1
47 ME 1882 Motor (over 600mm) 1
48 ME 2120 Motor (Up to 600mm) 1

RO-MP-2 5-3
CAM SHAFT ASSEMBLY
1620-0111-00 12/9/96

RO-MP-2 5-4
CAM SHAFT ASSEMBLY
1620-0111-00
Item Part Number: Description: Qty: Notes:
10 1620-0111-10 Shaft 1
11 1620-0111-11 Slide Plate Cam (Cam 27) 1 5-6mm Strap
12 1620-0111-12 Left Gripper Cam (Cam 28) 1
13 1620-0111-13 Knife Bar Cam (Cam 29) 1
17 0120-0111-03 Right Gripper Cam (Cam 21) 1
19 2902-010101-06 Heater Cam (Cam 38) 1
20 2101-2110-09 Spacer Bushing 1
25 NT 7 Retaining 2
27 NT 36 Key 1
29 NT 1582 Spacer 1
30 NT 1067 Spacer 1

RO-MP-2 5-5
UPPER SLIDE PLATE ASSEMBLY
1620-0120-00 4/7/97

RO-MP-2 5-6
UPPER SLIDE PLATE ASSEMBLY
1620-0120-00
Item Part Number: Description: Qty: Notes:
1 2125-0120-01 Strap Sensor Flag 1
2 2125-0120-02 Pin 1
7 0101-0121-01 Lower Slide Plate 1
8 0101-0120-01 ** Upper Slide Plate - Long 1
9 0401-0120-04 Shoulder Bolt 1
10 0401-0120-05 Washer 1
11 0101-0120-05 ** Bumper 1
21 NT 522 Du-Bushing 2
22 NT 663 ** Compression Spring 1
23 NT 891 Set Screw 1

RO-MP-2 5-7
SEALER: KNIFE-GRIPPER ASSEMBLY
0101-013000-16 8/15/1997

RO-MP-2 5-8
SEALER KNIFE-GRIPPER ASSEMBLY
0101-013000-16
Item Part Number: Description: Qty: Notes:
1 0101-013000-02 Knife Pressure Bar 1
2 0101-013000-03 ** Knife 1
3 0101-013000-08 ** Compression Spring 1
4 0101-013000-10 Spring Pin 1
5 0101-013000-20 Cam Roller Complete 1
15 NT 181 Roll Pin 1
16 NT 179 Socket Cap Screw 1

RO-MP-2 5-9
SEALER RIGHT GRIPPER ASSEMBLY
0101-0130-17 8/21/1997

RO-MP-2 5-10
SEALER RIGHT GRIPPER ASSEMBLY
0101-013000-17
Item Part Number: Description: Qty: Notes:
25 0101-013000-04 Right Gripper Bar 1
26 0101-013000-20 Cam Roller Complete 1
27 0101-013000-08 ** Compression Spring 1
28 0101-013000-10 Spring Pin 1
29 0101-013000-12 Spring Pin 1
31 NT 181 Roll Pin 1

RO-MP-2 5-11
SEALER LEFT GRIPPER ASSEMBLY
0401-0130-01 8/21/1997

RO-MP-2 5-12
SEALER LEFT GRIPPER ASSEMBLY
0401-0130-01
Item Part Number: Description: Qty: Notes:
2 0101-013000-01 Left Gripper Bar 1
3 0101-013000-10 Cam Roller Complete 1
4 0101-013000-08 ** Compression Spring 1
6 0101-013000-10 Spring Pin 1
8 NT 181 Roll Pin 1

RO-MP-2 5-13
SEALER KNIFE & GRIPPER BARS ASSEMBLY
1601-013000-16 3/5/1999

RO-MP-2 5-14
SEALER KNIFE & GRIPPER BARS ASSEMBLY
1601-013000-16
Item Part Number: Description: Qty: Notes:
1 0401-013000-01 Left Gripper Complete 1
11 0101-013000-16 Knife Pressure Bar Complete 1
24 0101-013000-17 Right Gripper Complete 1
34 0101-013000-13 Cover Plate 1
35 0101-013000-14 ** Tension Spring 1
61 NT 66 Lock Washer 4
62 NT 22 Socket Cap Screw 4
63 NT 567 ** Tension Spring 2

RO-MP-2 5-15
SEALER HOUSING ASSEMBLY
1620-0140-00 4/14/97

RO-MP-2 5-16
SEALER HOUSING ASSEMBLY
1620-0140-00
Item Part Number: Description: Qty: Notes:
10 1620-0140-10 Sealer Housing 1
11 1620-0140-11 Sensor Plate 1
12 1620-0140-12 Base Plate 1
13 1620-0140-13 Spacer Plate 1
18 2125-0100-10 Left Gib 1
19 2125-0100-11 Right Gib 1
20 2125-0100-13 Sensor Support Angle 1
21 2125-0100-14 Bumper Plate 1
23 0401-0100-01 Poly. Bumper 1
24 0401-0100-03 Nut Plate 1
25 0401-0100-04 Sensor Pin 1
26 0401-0100-05 ** Compression Spring 1
27 0401-0800-27 Pointer 1
35 NT 473 Socket Cap Screw 1
36 NT 523 Socket Cap Screw 1
37 NT 32 Washer 2
38 NT 74 Lock Washer 2
39 NT 61 Lock Washer 3
42 NT 995 Internal Snap Ring 2
43 NT 564 Internal Snap Ring 2
46 NT 874 Socket Cap Screw 4
47 NT 18 Socket Cap Screw 4
48 NT 171 Socket Cap Screw 6
49 NT 81 Socket Cap Screw 1
50 NT 141 Socket Cap Screw 1
51 NT 163 Socket Cap Screw 1
55 NT 502 Set Screw 1
58 NT 16 Hex Nut 1
60 NT 474 Nylock Nut 1
62 NT 454 Spacer 1
64 NT 111 Roll Pin 2
65 NT 233 Roll Pin 2
68 NT 1672 Lock Washer 6
70 NT 82 Washer 1
71 NT 1353 ** Bearing 2
74 ME 2247 ** Proximity Sensor 3
75 NT 533 Lock Washer 3
76 NT 870 Washer 2

RO-MP-2 5-17
HEATER ASSEMBLY - 24V. DC
0901-0160-00 5/22/96

NOTE: Screw (27) is welded on the

under side of mounting plate (4).

NOTE: Heater assembly does not

include Terminal Wire No. 41.

RO-MP-2 5-18
HEATER ASSEMBLY
0901-0160-00
Item Part Number: Description: Qty: Notes:
1 0901-0160-00 ** Heater Assembly 1
2 2601-0150-09 Heating Plate 1
3 0901-0160-01 Terminal Plate 1
4 2601-0150-03 Mounting Plate 1
5 2601-0150-04 Support Plate 1
6 2601-0150-06 Leaf Spring 1
20 NT 874 Socket Cap Screw 1
21 NT 450 Star Washer 1
22 NT 33 Hex Nut 6
24 NT 74 Lock Washer 1
25 NT 48 Hex Nut 2
26 NT 2132 VA Flat Head Screw 1
27 NT 2170 VA Flat Head Screw 1
28 NT 12 Washer 1
29 NT 774 Star Washer 2
30 NT 449 Socket Cap Screw 1
31 NT 32 Washer 1
32 NT 535 Nylock Nut 1
33 NT 1569 Hex Screw 1
34 NT 879 Socket Cap Screw 1
40 ME 193 Terminal Block 1
41 ME 1884A110 Terminal Wire 1
42 ME 1978 Ground Connector 1
43 ME 661 Wire Clamp 1

RO-MP-2 5-19
STRAP FEED PULL-BACK, TENSION ASSEMBLY
1699-016900-00 9/26/97

RO-MP-2 5-20
STRAP FEED PULL-BACK, TENSION ASSEMBLY
1699-016900-00 (5mm Strap)
Item Part Number: Description: Qty: Notes:
1 1620-016100-00 Brushless Motor with Adapter 1
10 1620-0160-10 Lower Strap Guide Cover 1 5-6mm Strap
11 1620-0160-11 Lower Strap Guide 1 5-6mm Strap
13 1620-0160-61 Upper Strap Guide Cover 1 5-6mm Strap
14 1620-0160-14 Gear 1 5-6mm Strap
16 1620-0160-16 Pilot Shaft 1
17 1620-0160-17 Feed Wheel 1 5-6mm Strap
18 1620-0160-18 Gear 1
20 1699-0165-69 ** Tension Roller 1 5-6mm Strap
21 1620-0160-21 Pivot 1
22 1620-0160-72 Roller Lever 1
24 1620-0160-77 Shaft for Roller Lever 1
25 1699-0161-10 Shaft 1
27 1620-0160-27 Clamp Bar 1
28 1620-0160-28 Solenoid Plate 1
29 1699-0163-29 Pressure Roller 1 5-6mm Strap
30 1699-0161-11 Spacer 1
31 1620-0160-31 Motor Support 1
44 1620-0160-44 Strap Guide Block 1
52 1620-0160-52 Adjustment Angle 1
53 1620-0160-71 Solenoid Angle Support 1
56 1620-0160-56 Strap Guide Block 1
57 1620-0160-57 Upper Strap Guide 1 5mm Strap
60 1620-0160-60 Spacer Plate 1
61 0101-0140-12 Gear 1
62 0101-0141-03 Threaded Bolt 1
63 0401-0710-04 Spring Pin 1
64 0401-0121-02 ** Tension Spring 1
65 0101-0140-48 Retaining Washer 1
66 NT 2321 Hex Nut 1
67 0401-0142-03 Spring Guide 1
69 1620-0160-70 Cam Roller Support Block 1
70 NT 76 Socket Cap Screw 1
71 NT 74 Lock Washer 11
72 NT 1899 Key 1
73 NT 545 Key 1
74 NT 24 Retaining Ring 3
75 NT 278 ** Bearing 2
77 NT 677A0210 Clutch Coil 1
78 NT 1706 Socket Cap Screw 7
79 NT 176 Lock Washer 19
80 NT 489 Spacer 0
81 NT 327 Spacer 0
82 NT 1353 ** Bearing 1
83 NT 433 Socket Cap Screw 3
84 NT 1107 Rib Washer 3
85 NT 891 Set Screw 1
86 NT 276 Socket Cap Screw 4
87 NT 72 Washer 6
88 NT 76 Socket Cap Screw 3
89 NT 685 ** Compression Spring 1

RO-MP-2 5-21
 STRAP FEED PULL-BACK, TENSION ASSEMBLY
1699-016900-00 (5mm Strap)
Item Part Number: Description: Qty: Notes:
90 NT 23 Socket Cap Screw 2
91 NT 13 Hex Nut 2
92 NT 8 Socket Cap Screw 8
93 NT 2150 Roll Pin 4
95 NT 80 Key 1
96 NT 92 Socket Cap Screw 2
98 NT 987 Flat Head Screw 2
99 NT 389 ** Bearing 2
100 NT 12 Washer 3
101 NT 717 Spacer 0
102 NT 101 Retaining Ring 1
104 NT 458 Nylock Nut 3
104 NT 15 Washer 2
106 NT 325 Hex Nut 4
107 NT 339 Washer 1
108 NT 6 Socket Cap Screw 1
109 NT 66 Lock Washer 3
110 NT 1636 ** Bearing 2
111 NT 2325 Retaining Ring 1
112 NT 520 Retaining Ring 1
113 NT 649 Set Screw 1
114 NT 6 Socket Cap Screw 1
115 NT 2328 Washer 1
116 NT 2261 Woodruff Key 1
118 NT 95 Socket Cap Screw 5
119 NT 309 Washer 1
120 NT 568 Cam Roller 1
121 NT 171 Socket Cap Screw 1
122 NT 339 Washer 1
128 ME 892A02 Clutch Armature 1
130 ME 2136 Double Solenoid 1
131 ME 2170 Motor 60 V. DC 1
140 NT 92 Socket Cap Screw 4
142 NT 176 Lock Washer 4
144 NT 1839 Key 1

RO-MP-2 5-22
NOTES:

RO-MP-2 5-23
HEATER ARM ASSEMBLY - 24 V. DC
2601-0170-00 8/24/96

RO-MP-2 5-24
HEATER ARM ASSEMBLY
2601-0170-00
Item Part Number: Description: Qty: Notes:
1 26001-0171-00 Heater Arm Complete 1
2 2601-0170-08 Arm Shaft 1
3 0101-0151-03 Spring Bolt 1
4 0101-0151-04 Bushing 1
5 0101-0151-05 Spring Pin 1
6 0101-0151-06 Socket Cap Screw 2
31 NT 406 Snap Ring 2
34 NT 474 Nylock Nut 2
35 NT 16 Hex Nut 2
38 NT 2203 ** Tension Spring 1
39 NT 1634 Collar Bushing 2
40 NT 61 Lock Washer 1
42 NT 66 Lock Washer 1
46 NT 339 Flat Head Screw 1
47 NT 14 Hex Nut 1
48 NT 1923 ** Tension Spring 1
49 NT 69 Flat Head Screw 1
53 NT 13 Hex Nut 1

RO-MP-2 5-25
SLIDE PLATE LEVER ASSEMBLY
1620-018000-00 10/28/96

RO-MP-2 5-26
SLIDE PLATE LEVER ASSEMBLY
1620-018000-00
Item Part Number: Description: Qty: Notes:
10 1620-0180-10 Shaft 1
12 1620-0180-12 Slide Plate Lever 1
16 0401-0121-01 Sensor Flag 1
17 0101-0130-11 Spring Pin 1
23 NT 176 Lock Washer 2
25 NT 1706 Socket Cap Screw 2
26 NT 891 Set Screw 1
29 NT 16 Hex Nut 1
31 NT 555 Dowel Pin 1
33 NT 1634 Flange Bushing 2
37 NT 568 Cam Follower 1
38 NT 29 Set Screw 1

RO-MP-2 5-27
CASTER FRAME ASSEMBLY
500-600-800-1000 MACHINES 1620-021000-00 6/18/1998

RO-MP-2 5-28
CASTER FRAME ASSEMBLY
500, 600, 800, 1000 MACHINES 1620-021000-00
Item Part Number: Description: Qty: Notes:
1 1620-021100-00 Frame Assembly Right 2
2 1699-0201100-10 Frame Assembly Left 2
5 1699-020100-10 Washer 2
6 0401-010000-03 Nut Plate 1
9 NT 32 Washer 2
10 NT 490 Socket Cap Screw 2
11 1620-021000-10 Washer 4
12 NT 2364 Caster with Brake 2
13 NT 2412 Caster without Brake 2
16 1620-021000-16 Caster Reinforcement 2
17 1620-021000-17 Restriction Plate 1
19 ME 2247 ** Proximity Sensor 1
20 ME 1444 Bushing 8mm 1
21 NT 2412 Caster Non-Swivel 2
22 NT 64 Roll Pin 2
23 NT 1706 Socket Cap Screw 2
24 NT 176 Lock Washer 2
25 NT 72 Washer 2
26 NT 647 Socket Cap Screw 2

RO-MP-2 5-29
FOOT PEDAL ASSEMBLY
500-600-800 MACHINES 1620-0220-00 12/20/95

RO-MP-2 5-30
FOOT PEDAL ASSEMBLY
500 & 600 1620-0220-00
800 1630-0220-00
Item Part Number: Description: Qty: Notes:
1 1620-0221-00 Foot Rail Assembly 500 & 600 1
2 1630-0221-00 Foot Rail Assembly 800 1
10 1601-0220-10 Shaft 2
20 NT 1039 Bushing 8mm 4
21 NT 43 Retaining Ring 4
22 NT 697 ** Tension Spring 2

RO-MP-2 5-31
SIDE PANELS & REAR COVER ASSEMBLY
500-600-800 MACHINES 1620-0230-00 1/30/98

RO-MP-2 5-32
SIDE PANELS & REAR COVER ASSEMBLY
500 & 600 1620-0230-00
800 1630-0230-00
Item Part Number: Description: Qty: Notes:
1 1620-0231-00 Right Side Plate Assembly 1
2 1620-0232-00 Left Side Plate Assembly 1
3 1620-0233-00 Rear Cover Assembly 1 500 & 600
4 1620-0234-00 Rear Cover Roller Assembly 1 500 & 600
5 1620-0236-00 Support Bar 1 500 & 600
6 1630-0233-00 Rear Cover Assembly 1 800
8 1630-0234-00 Rear Cover Roller Assembly 1 800
9 NT 2623 Hand Rail 1
10 2101-1200-22 Stand Off 6
11 1620-0230-11 Nut Plate 1
13 1630-0235-00 Support Bar 1 800
14 NT 737 Lock Bolt 6
15 NT 2108 Button Head Screw 4
16 NT 228 Hex Screw 8
17 NT 1124 Flat Head Screw 2
18 NT 822 Washer 2
19 NT 535 Nylock Nut 2
20 NT 14 Hex Nut 6
21 NT 66 Lock Washer 6
22 NT 290 Socket Cap Screw 2
23 NT 12 Washer 2
24 NT 74 Lock Washer 2
25 ME 1823 Safety Switch 1 Schmersal ( )
26 NT 46 Bearing 2
27 NT 3 Retaining Ring 2
28 NT 738 Lock Bolt 1
30 0401-0200-37 Dispenser Idler Roller 1
31 0401-0200-38 Shaft 2
39 NT 87 Lock Washer 2
40 NT 228 Hex Screw 2
42 ME 2587 Safety Switch 1 Bernstein ( )

RO-MP-2 5-33
FRONT DOOR & EXTENSION COVER ASSEMBLY
500-600 MACHINES 1620-0240-00 6/3//97

RO-MP-2 5-34
FRONT DOOR & EXTENSION COVER ASSEMBLY
500 & 600 1620-0240-00
Item Part Number: Description: Qty: Notes:
1 1620-0241-00 Front Door Complete 1
10 1620-0240-10 Support Bar 1
11 2101-1200-22 Stand Off 2
14 NT 737 Lock Screw 2
15 NT 1209D Lock Complete with Knob 1
16 NT 1764 Door Hinge 2
17 ME 1825 ** Safety Switch Actuator 1 Schmersal ( )
19 NT 571 Flat Head Screw 2
20 NT 66 Lock Washer 4
21 NT 175 Hex Screw 2
22 NT 14 Hex Nut 2
23 ME 1191 Vinyl Data Pocket 1
24 ME 2683 ** Safety Switch Actuator 1 Bernstein ( )

RO-MP-2 5-35
TABLE PLATE ASSEMBLY
500-600- 800 MACHINES 1630-0250-00 5/29/96

RO-MP-2 5-36
TABLE PLATE ASSEMBLY Corning
1630-0250-00-A
Item Part Number: Description: Qty: Notes:
4 1630-0251-00 Front Table Plate 800 1
10 1630-0250-10 Rear Table Plate 800 1
12 1622-0250-11 Table Support 1
13 1630-0250-11 Shaft 800 1
15 0401-0210-09 Nut Plate 4
16 0120-0200-12 Hinge Block 2
17 0101-0100-17 Table Bumper 1
30 NT 439 Flat Head Screw 4
31 NT 535 Nylock Nut 4
32 NT 571 Flat Head Screw 2
33 NT 390 Flat Head Screw 2
34 NT 81 Socket Cap Screw 2
35 NT 15 Washer 2
36 NT 61 Lock Washer 2
37 NT 266 Socket Cap Screw 1
38 NT 239 Hex Nut 1
40 ME 1825 Switch Actuator 1
41 NT 171 Socket Cap Screw 2
42 NT 66 Lock Washer 2

RO-MP-2 5-37
CENTER FRAME ASSEMBLY
500-600 MACHINES 1620-0260-00 11/27/96

RO-MP-2 5-38
CENTER FRAME ASSEMBLY
500 & 600 1620-0260-00
Item Part Number: Description: Qty: Notes:
1 1620-0261-00 Frame Complete 1
2 1620-0262-00 Support Plate Complete 1
11 1620-0260-11 Cover 1
18 NT 176 Lock Washer 4
19 NT 72 Washer 2
21 NT 180 Roll Pin 4
22 NT 179 Socket Cap Screw 2
26 NT 95 Socket Cap Screw 2
27 NT 1149 Lock Screw 4
31 ME 1356 Cable Clamp 2
32 ME 1444 Bushing 8mm 2
33 ME 1791 Push Button 1
34 ME 771 Cover 1

RO-MP-2 5-39
DISPENSER ASSEMBLY
1601-0310-00 10/6/97

RO-MP-2 5-40
DISPENSER ASSEMBLY
1601-0310-00
Item Part Number: Description: Qty: Notes:
7 1601-0310-09 Knob 1
8 1601-0310-10 Bayonet Plate 1
9 1601-0310-11 Guide Bushing 1
10 1601-0310-12 Bayonet Shaft 1
11 1601-0310-13 Bell Housing 1
12 1601-0310-15 Washer 1
13 0101-0300-19 Dispenser Foam Pad - Thick 8
14 1601-0310-17 Dispenser Foam Pad - Thin 8
15 1601-0310-18 Front Disc 1
16 1601-0310-19 Rear Disc 1
17 1601-0310-20 Front Brace 4
18 1601-0310-21 Rear Brace 4
19 1601-0310-22 Leaf Spring 4
31 NT 184 Socket Cap Screw 8
32 NT 12 Washer 8
33 NT 535 NyLock Nut 8
34 NT 932 Hex Screw M5x6 8
36 NT 1398 Rivet 16
37 NT 81 Socket Cap Screw 1
48 NT 1397 Dowel Pin 1
49 NT 50 Snap Ring 2
50 NT 993 Washer 1
51 NT 660 Compression Spring 1
52 NT 612 Arrow 4
54 NT 61 Lock Washer 1

RO-MP-2 5-41
DISPENSER SUPPORT ASSEMBLY
1620-032000-00 6/17/96

RO-MP-2 5-42
DISPENSER SUPPORT ASSEMBLY
1620-032000-00
Item Part Number: Description: Qty: Notes:
1 1620-0321-00 Brake Support Complete 1
10 1620-0320-10 Bearing Block 1
14 0401-0300-08 Spacer Ring 1
15 0401-0300-07 Shaft 1
25 NT 102 E-clip 1
26 NT 681 Spacer Ring 1
27 NT 717 Spacer Ring 1
28 NT 192 Bearing Block 2
29 NT 85 Flat Head Screw 3
30 NT 74 Lock Washer 4
31 NT 8 Socket Cap Screw 4
32 NT 35 Key 2
34 ME 46E00 Brake (KEB) 1

RO-MP-2 5-43
ACCUMULATOR FILL ASSEMBLY
1620-0710-00 2/19/97

RO-MP-2 5-44
ACCUMULATOR FILL ASSEMBLY
1620-0710-00 (5-6mm Strap)
Item Part Number: Description: Qty: Notes:
1 1620-0711-00 Strap Threading Gate Complete 1 5-6mm Strap
6 1620-0716-00 Motor 60 V. DC (DUNKER) 1
7 1620-071700-00 Motor 60 V. DC (GEFEG) 1
10 1620-0710-10 Motor Support 1
11 1620-0710-11 Stop Bar 1
12 1620-0710-12 Strap Guide 1 5-6mm Strap
13 1620-0710-13 Strap Guide 1 5-6mm Strap
14 1620-0710-14 Stand Off 1
15 1620-0710-15 Flanged Bearing Housing 2
16 0101-0140-48 Spacer Washer 1
17 1620-0710-17 Eccentric Shaft 1
19 1620-0710-19 Spacer Ring 1
20 1620-0710-20 Adjustment Collar 1
22 1620-0710-22 Strap Cover 1 5-6mm Strap
23 1620-0710-23 Drive Roller 1
33 1620-0710-33 Flanged Bushing Housing 1
34 1620-0710-34 Sensor Bracket 1
35 1620-0710-35 Strap Guide 1 5-6mm Strap
36 1620-0710-36 Cover Plate 1
40 1620-0710-40 ** Pressure Roller 1 5-6mm Strap
44 1620-0710-44 Bushing 1
48 1699-0162-12 Threaded Rod 1
49 2601-0700-20 Retaining Washer 1
50 2601-0730-16 Auto Feed Sensor Actuator 1
51 2601-0700-17 Connecting Link 1
52 0401-0810-23 Shoulder Bolt 1
53 0401-0710-12 Shoulder Bolt 1
54 0401-0710-11 Collar 1
55 0401-0710-10 Guide Roller 1
56 0401-0710-18 Spacer Ring 1
57 0401-0710-09 Collar 1
65 NT 95 Socket Cap Screw 8
66 NT 176 Lock Washer 12
67 NT 939 Flat Head Screw 2
68 NT 877 Socket Cap Screw 2
69 NT 32 Washer 2
70 NT 339 Hex Nut 2
71 NT 2150 Roll Pin 1
72 NT 8 Socket Cap Screw 7
73 NT 532 Clevis with Safety 1
74 NT 48 Hex Nut 3
75 NT 1361 Compression Spring 1
77 NT 642 Set Screw 1
78 NT 72 Washer 2
79 NT 871 Flat Head Screw 2
80 NT 1706 Socket Cap Screw 2
81 NT 13 Hex Nut 3
82 NT 474 Nylock Nut 1
83 NT 117 Socket Cap Screw 1
84 NT 43 Retaining Ring 2
85 NT 52 DU-Bushing 2

RO-MP-2 5-45
 ACCUMULATOR FILL ASSEMBLY
1620-0710-00 (5-6mm Strap)
Item Part Number: Description: Qty: Notes:
86 NT 92 Socket Cap Screw 3
87 NT 461 Spacer 1
88 NT 46 ** Bearing 2
89 NT 45 Snap Ring 1
90 NT 3 E-Clip 1
91 NT 458 Nylock Nut 1
92 NT 74 Lock Washer 3
94 NT 973 Set Screw 4
97 NT 556 Socket Cap Screw 8
98 NT 85 Flat Head Screw 3
99 NT 156 ** Bearing 2
100 NT 344 Snap Ring 1
101 NT 1509 ** Tension Spring 1
102 NT 2324 Bearing 1
105 ME 2247 Proximity Sensor 1
106 ME 1247 ** Solenoid 24 V. DC 1
108 NT 757 Bushing 1
109 NT 699 Bushing 1
110 NT 2292 Washer 1
111 NT 445 Nylock Nut 1
112 NT 76 Socket Cap Screw 4
114 NT 533 Lock Washer 2

RO-MP-2 5-46
NOTES:

RO-MP-2 5-47
ACCUMULATOR ASSEMBLY
500-600 MACHINE 1620-0730-00 6/19/97

NOTE: DO NOT overtighten

mounting screws (51). Fasten
mounting screws tight enough to
hold accumulator plate (10)
securely and then back out 1/8th
turn to have washers float. The
plexiglas must have room for
expansion.

RO-MP-2 5-48
ACCUMULATOR ASSEMBLY
500 & 600 1620-0730-00
Item Part Number: Description: Qty: Notes:
8 1620-073000-10 Accumulator Front Cover 10mm Thick 1
9 1620-073000-11 Accumulator Door 10mm Thick 1
10 1620-072000-10 Accumulator Front Cover 8mm Thick 1
11 1620-072000-11 Accumulator Door 8mm Thick 1
12 1620-072000-12 Right Support Angle 1
13 1620-072000-13 Bottom Support Angle 1
14 1620-072000-14 Top Support Angle 1
15 1699-072100-15 Latch 1
17 1620-072000-17 Sensor Actuator Lever 1
18 1620-072000-18 Proximity Sensor Bracket 1
21 1620-072000-21 Spring Adjustment Angle 1
22 1620-073000-22 Support Angle for 10mm Cover 1
22 1620-0720-22 Support Angle for 8mm Cover 1
25 0401-070000-19 Bushing 1
30 NT 653 Hex Screw 8
31 NT 176 Lock Washer 6
32 NT 72 Washer 12
33 NT 27 Socket Cap Screw 1
34 NT 309 Washer 5
37 NT 2644 Socket Cap Screw 8
38 NT 692 Hinge 2
41 NT 939 Flat Head Screw 4
42 NT 691 Socket Cap Screw 2
43 NT 32 Washer 2
44 NT 95 Socket Cap Screw 2
45 NT 1211 Latch Support 1
46 NT 2331 ** Tension Spring 1
47 NT 162 Socket Cap Screw 2
49 ME 2247 Proximity Sensor 1
51 NT 2643 Hex Screw 11
52 NT 203 Socket Cap Screw 1
53 NT 13 Hex Nut 1
54 NT 870 Washer 8

RO-MP-2 5-49
OUTER STRAP TRACK ASSEMBLY
500/400 MACHINE 1621-0810-00 9/29/97

RO-MP-2 5-50
OUTER STRAP TRACK ASSEMBLY
500/400 1621-0810-00
Item Part Number: Description: Qty: Notes:
2 1621-0811-00 Outer Strap Track 500/400 1
11 1620-0810-16 Spacer 2
12 1621-1140-10 Cable Channel 500/400 1
13 1620-0810-13 Safety Switch Support Plate 1
18 1601-0800-25 ** Left Stripper 1
19 1601-0800-56 ** Right Stripper 1
20 1601-0800-23 Support Angle 1
21 1601-0800-07 Spacer Bolt 2
22 1601-0810-60 ** Ejector Pin Bracket Complete 1
23 1620-0810-60 ** Ejector Pin Bracket Complete 1
24 0101-0140-48 Washer 4
29 NT 48 Hex Nut 2
30 NT 12 Washer 4
31 NT 41 Socket Cap Screw 4
32 NT 44 Socket Cap Screw 4
33 NT 66 Lock Washer 6
35 NT 1773 Lock Screw 2
37 NT 2108 Button Head Screw 6
38 NT 16 Hex Nut 6
39 NT 61 Lock Washer 6
40 NT 15 Washer 6
41 NT 74 Lock Washer 6
42 NT 8 Socket Cap Screw 2
43 NT 184 Socket Cap Screw 2
44 ME 1823 Safety Switch 1 Schmersal ( )
45 NT 503 Roll Pin 4
46 NT 19 Washer 4
47 NT 322 Socket Cap Screw 1
48 NT 1 Hex Screw 1
49 NT 76 Socket Cap Screw 2
50 NT 1109 Frame Cap 1
52 NT 2365 Socket Cap Screw 4
53 NT 822 Washer 2
56 ME 2131 Grommet 1
57 ME 2587 Safety Switch 1 Bernstein ( )

RO-MP-2 5-51
INNER STRAP TRACK ASSEMBLY
500/400 MACHINE 1621-0820-00 5/31/1999

RO-MP-2 5-52
INNER STRAP TRACK ASSEMBLY
500/400 1621-0820-00 (5-6mm Strap)
Item Part Number: Description: Qty: Notes:
1 1603-0810-01 Inner Strap Track Frame 500/400 1
2 1621-0821-00 Right Bar Assembly 500/400 1
11 1620-0820-11 Collar 2
13 1621-0820-13 Strap Track 500/400 1 5-6mm Strap
15 1620-0820-15 Bottom Strap Guide Left 1 5-6mm Strap
17 0401-0810-21 Frame Link 4
18 0401-0810-25 Bolt 4
19 0401-0810-22 Pivot Plate 4
20 0401-0810-32 Bearing Block 2
21 0401-0810-44 Bushing 2
22 0401-0810-27 Bottom Strap Guide - Right 1
23 0401-0810-28 Center Strap Guide - Right 1
24 0401-0810-26 Top Strap Guide - Right 1
25 0401-0810-47 Top Strap Guide - Left 1
27 0401-0810-36 Track Sensor Bracket 1
28 0401-0810-31 Bridge 1
29 1601-0810-31 Left Bar Assembly Complete 1
30 0401-0810-20 Top Link 3
31 0401-0810-24 Shoulder Bolt 3
32 0401-0810-17 Bearing Block 2
33 1601-0810-60 Ejector Pin Bracket Complete 2
35 1601-0810-41 Connecting Rod 1
36 0401-0810-45 Track Alignment Angle 10
37 0701-0810-09 Heater Cover Plate 1
39 0401-0810-23 Shoulder Bolt 12
46 NT 19 Washer 4
47 NT 346 Socket Cap Screw 2
48 NT 1402 Flat Head Screw 4
49 NT 691 Socket Cap Screw 2
50 NT 5 Flat Head Screw 2
51 NT 162 Socket Cap Screw 2
52 NT 176 Lock Washer 2
53 NT 72 Washer 2
54 ME 2247 Proximity Sensor 1
55 NT 322 Socket Cap Screw 2
56 NT 1051 Flat Head Screw 2
57 NT 44 Socket Cap Screw 2
58 NT 13 Hex Nut 10
59 NT 1706 Socket Cap Screw 10
60 NT 98 Socket Cap Screw 4
61 NT 94 Hex Screw 4
62 NT 74 Lock Washer 8
63 NT 12 Washer 4
64 NT 637 Retaining Ring 4
65 NT 348 Dowel Pin 2
66 NT 474 Nylock Nut 10
67 NT 309 Washer 10
68 NT 1604 Flat Head Screw 10
69 NT 699 DU-Bushing 8
70 NT 25 DU-Bushing 3

RO-MP-2 5-53
 INNER STRAP TRACK ASSEMBLY
500/400 1621-0820-00 (5-6mm Strap)
Item Part Number: Description: Qty: Notes:
71 NT 64 Roll Pin 3
72 NT 66 Lock Washer 4
73 NT 664 ** Tension Spring 2
75 NT 2282 Heater Warning Sign 1

RO-MP-2 5-54
NOTES:

RO-MP-2 5-55
STRAP FRAME COVER ASSEMBLY
500/400 MACHINE 1621-0830-00 11/21/97

RO-MP-2 5-56
STRAP FRAME COVER ASSEMBLY
500/400 1621-0830-00
600/500 1622-0830-00
800/400 1631-0830-00
Item Part Number: Description: Qty: Notes:
2 1621-0831-00 Track Cover Assembly 500/400 1
3 1622-0831-00 Track Cover Assembly 600/500 1
4 1631-0831-00 Track Cover Assembly 800/400 1
8 1621-0830-13 Brush 500/400 1
9 1622-0830-10 Brush 600/500 1
10 1630-0830-10 Brush 800/400 1
12 1621-0830-11 Brush 500/400 1
13 1622-0830-11 Brush 600/500 1
14 NT 2597 Brush Clip 6
15 NT 797 Washer 6
16 1621-0830-11 Brush 800/400 1
31 NT 1051 Buttonhead Screw 5
40 NT 1815 Manufacturer's Sign 1
43 NT 1814 Rivet 2
44 NT 2596 Lock Screw 6

RO-MP-2 5-57
STRAP TRACK OPENER ASSEMBLY
500/400 MACHINE 1621-0840-00 1/30/96

RO-MP-2 5-58
STRAP TRACK OPENER ASSEMBLY
500/400 1621-0840-00
600/500 1622-0840-00
800/400 1630-0840-00
800/600 1630-0840-00
Item Part Number: Description: Qty: Notes:
10 1620-0840-10 Bearing Block 1
21 0401-0820-01 Track Opener Arm 1
22 1608-0820-02 Track Opener Shaft 800/400 & 800/600 1
23 0401-0820-03 Bearing Block 1
24 0101-0151-03 Pivot Block 1
25 0101-0151-04 Bushing 1
26 0401-0820-13 Flange Bushing 1
27 0401-0820-14 Eye Bolt 1
29 1603-0820-02 Track Opener Shaft 500/400 1
30 1602-0820-02 Track Opener Shaft 600/500 1
31 NT 61 Lock Washer 1
32 NT 198 Flat Head Screw 1
33 NT 497 Flat Head Screw 1
34 NT 14 Hex Nut 2
35 NT 424 ** Bearing 1
36 NT 514 Spacer 1
37 NT 66 Lock Washer 4
38 NT 185 Hex Screw 4
39 NT 1205 Bushing 2
40 NT 581 Set Screw 1
41 NT 694 Collar 1
42 NT 696 ** Tension Spring 1
43 NT 141 Socket Cap Screw 1
44 NT 339 Washer 5

RO-MP-2 5-59
FAN ASSEMBLY
1620-0850-00 7/7/97

RO-MP-2 5-60
FAN ASSEMBLY
1620-0850-00
Item Part Number: Description: Qty: Notes:
1 1620-0851-00 Fan Bracket Complete 1
10 0101-0100-17 ** Bumper 1
31 ME 1759 Fan 24 V. DC 1
32 ME 1249 Fan Guard 1
33 NT 203 Socket Cap Screw 2
34 NT 176 Lock Washer 4
35 NT 72 Washer 4
36 NT 13 Hex Nut 4
37 NT 27 Socket Cap Screw 2
38 NT 22 Socket Cap Screw 1
39 NT 66 Lock Washer 1
40 NT 19 Washer 1
41 NT 1048 Socket Cap Screw 1
42 NT 239 Hex Nut 1
43 ME 1449 Fan Guard 1

RO-MP-2 5-61
ELECTRICAL COMPONENTS ASSEMBLY
1620-1100-00 12/3/97

RO-MP-2 5-62
ELECTRICAL COMPONENTS ASSEMBLY
1620-1100-00
Item Part Number: Description: Qty: Notes:
1 1620-110000-25 Base Plate Complete 1
3 1620-1102-00 Cover 1
4 1620-1130-00 Control Panel Assembly 1
5 1620-1150-00 Enclosed Components Assembly 1
10 1620-1100-10 Stand Off 4
11 1620-1100-24 Din Rail 1
12 1620-1100-12 Cable Channel 2
13 1620-1100-13 Cable Channel Cover 2
14 1620-1100-14 Cable Channel 1
15 1620-1100-15 Cable Channel Cover 1
23 1620-1100-23 Adapter Plate 1
24 NT 66 Lock Washer 2
25 NT 95 Socket Cap Screw 14
26 NT 322 Socket Cap Screw 2
28 NT 309 Washer 8
29 NT 339 Washer 2
30 NT 1124 Flat Head Screw 2
31 NT 1050 Lock Screw 2
32 NT 8 Socket Cap Screw 2
33 NT 74 Lock Washer 2
34 NT 12 Washer 2

RO-MP-2 5-63
CONTROL PANEL ASSEMBLY
1620-1130-00 8/26/97

RO-MP-2 5-64
CONTROL PANEL ASSEMBLY
1620-113000-00
Item Part Number: Description: Qty: Notes:
1 1620-113100-00 Control Panel Cover Assembly 1
10 1620-113000-10 Control Panel Face Plate 1
14 NT 806 Star Washer 1
15 NT 13 Hex Nut 1
16 NT 146 Flat Head Screw 1
17 NT 74 Lock Washer 2
18 NT 176 Lock Washer 2
19 NT 8 Socket Cap Screw 2
20 NT 13 Hex Nut 1
21 NT 2332 Countersunk Screw 2
22 ME 457 Cable Connector 1
23 NT 822 Washer 2
24 ME 952 Snap Plug 2
25 ME 2555 Main Switch 1
26 ME 456 Hex Nut (Metal) 1
27 ME 278 A Illuminated Push Button 1
28 ME 52 A Illuminated Push Button Base 1
29 ME 1842 ** Bulb 24 V. 1
30 0101-0140-48 Retaining Washer 2
31 ME 55 A Pilot Light 1
32 ME 90 A Light Base 1
33 ME 266 ** Bulb 130 V. 1
34 ME 314 A Light Base 1
35 ME 1668 Potentiometer 1
36 ME 1128 Dial Plate 1
37 ME 1129 Knob 1
38 ME 2615 Power Line Cable 1
39 ME 1797 Plug 1
41 ME 1665 A L.E.D. 1
42 ME 1813 Plug 1
43 ME 1682 Cable Clip 1
44 NT 41 Cheese Head Screw 1
45 ME 2131 Cable Grommet 1
46 ME 2130 Cable Grommet 1
47 ME 666 Cable Clamp 1
48 ME 1680 Counter (optional) 1
49 ME 121 A Selector Switch - 3 Position (optional) 1
50 ME 1934 Illuminated Push Button Base 3 Pos. (opt.) 1
51 ME 98 A Push Button Base - 2 Position 1
52 ME 100 A Selector Switch - 2 Position 1

RO-MP-2 5-65
SUPPORT FRAME ASSEMBLY
500/400 1621-1401-00 2/12/1998

RO-MP-2 5-66
SUPPORT FRAME ASSEMBLY
500/400 1621-1401-00
Item Part Number: Description: Qty: Notes:
5 1621-140110-00 Frame 1
12 1621-140100-12 Nut Plate 1
15 NT 261 Socket Cap Screw 2
16 NT 61 Lock Washer 4
17 NT 82 Washer 4
18 NT 16 Hex Nut 4
20 NT 815 Socket Cap Screw 2

RO-MP-2 5-67
DOUBLE COMPACTOR ASSEMBLY
500/400 1621-1501-00 1/04/1998

RO-MP-2 5-68
DOUBLE PRESS ASSEMBLY (OPTIONAL)
400-300 1620-1501-00
500/400 1621-1501-00
Item Part Number: Description: Qty: Notes:
1 1622-150110-00 Right Press Block Support 1
2 1622-150120-00 Left Press Block Support 1
3 1622-150130-00 Alignment Coupling 400/300 1
8 1622-150100-08 Press Block Cover 1
9 1622-150100-09 Press Block Cover 1
12 1630-150100-12 Press Plate Front 1
13 1630-150100-13 Press Plate Rear 1
14 1622-150100-14 Stand Off 2
15 1622-150100-15 Solenoid Valve Bracket 1
16 3105-120000-02 Press Rod Connector 2
17 1620-150100-17 Press Rod 400/300 4
18 3105-120000-01 Press Block 1
19 1620-150100-19 Brush 400/300 2
20 1620-150100-20 Press Pad 400/300 2
21 0502-0220-24 Nut Plate 2
22 1622-150100-22 Shield 1
27 NT 27 Socket Cap Screw 6
28 NT 72 Washer 6
29 NT 16 Hex Nut 2
30 NT 268 Socket Cap Screw 4
31 NT 61 Lock Washer 16
32 NT 15 Washer 12
33 NT 2368 Buttonhead Screw 8
34 NT 144 Socket Cap Screw 4
35 NT 66 Lock Washer 4
36 NT 19 Washer 6
37 NT 2444 Warning Sign 2
38 NT 674 Manufacturer's Plate 1
39 NT 927 Socket Cap Screw 2
40 NT 309 Washer 2
41 NT 176 Lock Washer 4
42 NT 141 Socket Cap Screw 4
43 NT 117 Socket Cap Screw 2
44 NT 13 Hex Nut 2
45 NT 49 Hex Screw 4
46 NT 302 Hex Screw 4
47 ME 837 Coil Plug 1
48 ME 836 Coil Plug Gasket 1
49 NP 143 Alignment Coupling 500/400 1
50 NP 547 Filter Regulator 1
51 NP 176G Angle Connector 1
52 NP 32 Angle Connector 1
53 NP 30 Seal Ring 1
54 NP 18 Seal Ring 2
55 NP 266 T- Connector G 1/4" 1
56 NP 16 Reducer Bushing 1
57 NP 17 Hand Shut-Off Valve 1
58 NP 237 Hose Connector 1
59 NP 29 Angle Connector 1
60 NP 121 Quick Disconnect 1

RO-MP-2 5-69
 DOUBLE PRESS ASSEMBLY (OPTIONAL)
400-300 1620-1501-00
500/400 1621-1501-00
Item Part Number: Description: Qty: Notes:
61 NP 2 C Angle Connector 2
62 NP 24 C Tubing 3
63 NP 458C01 Solenoid Valve w/Coil 1
64 NP 267 Muffler 2
65 NP 379 G Angle Connector 3
66 NP 1 Air Cylinder, 40 x 200 400/300 1
67 NP 21 Quick Disconnect 1
68 NP 156 Hose Clamp 2
69 NP 46 Hose 8 x 3 5
70 NP 19 Quick Disconnect 1
71 0219-040000-13 Press Rod 500/400 4
72 0401-130000-03 Brush 500/400 2
73 1621-150100-20 Press Pad 500/400 2
74 NP 36 Air Cylinder, 40 x 320 500/400 1

RO-MP-2 5-70
NOTES:

RO-MP-2 5-71
RO-MP2 PHOTO CONTROL 1999
1511-0090 4/6/1999

1. Remove H1 (selector switch) completely. (see diagram page 2.5) Diagram shown below is found
under H1 selector switch.
2. Drill 7.5mm hole next to right side of "power on" label for new smaller "power on" light.
3. Hook Indicator lens up to T2 and T4 on main switch.
4. Install switch and switch body where H1 used to be, with red toward back.
5. Wire according to illustration.
6. Install label on front panel on top of existing Mosca label.

Power on Light
Wire #10 Wire #9

Weld Main Switch

Top
Temperature
Indicator (Red)
Rear view with panel N.C.
flipped upside down. (Green)
N.O.
V1/R9

Q1
Jumper Wire #11
Electrical Box

1. Locate cable from control panel and install wires to the following:
• wire #11 - Plug X11 Terminal 7
• wire #9 - Plug X11 Terminal 5
• wire #10 - Plug X6 Terminal 9

2. Install photo wires to the following on X6:

• Black - Plug X6 Terminal 9 with wire #10.
• Brown - Plug X6 Terminal 7.
• Blue and Orange - Plug X6 Terminal 8.

3. Run wires from the bottom of plugs X11 and X6 to the following:
• Plug X11 Terminal 7 to E7 on P.C. Board.
• Plug X11 Terminal 5 to E4 on P.C. Board
• Plug X6 Terminal 7 to 31
• Plug X6 Terminal 8 to 20

Photo Control

1. Mount on right side of machine in front of cable tube.

2. Drill (2) 2.5mm holes for photo control and use 3mm tap. (Keep photo at least 2mm off of table)
3. Use (2) 3 x 22mm screws that are included with the photo control for mounting photo. Add 4mm wide
washers (as needed) between the photo control and machine frame to properly align the photo and
reflector. Grind off screw ends if they are not flush with the track frame.

Reflector Bracket

1. Mount bracket on left side of machine so it sits at least 2mm above table top.
2. Drill (2) 3.3mm holes into side of track frame; Partially countersink holes and then tap 4mm.
3. For 500/400 machines or smaller, the reflector must be diagonally cut on the corner for access to the
table mounting screw.
4. Install Bracket using 4 x 8mm flat head screws.
5. Make sure front table top does not hit screws when it is lifted up.

RO-MP-2 5-72
RO-MP-2 PHOTO CONTROL 1999
1511-0090
Item Part Number: Description: Qty: Notes:
1 ME 1851 Photo Control 1
2 1023-0644 Indicator 1
3 ME 121A 3 Position Switch 1
4 ME 160A Switch Body 1
6 ME 1151 Reflector Tape 1
7 1036-0057 Reflector Bracket 1
8 1039-0003 Name Plate 1
9 NT 5 Flat Head Screw 4 x 8mm 2
10 ME 1374 Insulated Wire Tip (Red) 2
11 ME 1372 Insulated Wire Tip (Gray) 2
12 ME 1043 Insulated Wire Tip (White) 3
13 ME 1435 Connector 4
14 1025-0403 Wire #18 (Blue) 4 Ft.

RO-MP-2 5-73
RO-MP-2 5-74