Technical data sheet PRCA-BAC-S2-T-250

Rotary actuator for butterfly valves

• Nominal torque 160 Nm
• Nominal voltage AC 24...240 V / DC
24...125 V
• Control modulating, communicative
• with 2 integrated auxiliary switches
• Conversion of sensor signals
• Communication via BACnet MS/TP,
Belimo MP-Bus or conventional
control

Technical data
Electrical data Nominal voltage AC 24...240 V / DC 24...125 V
Nominal voltage frequency 50/60 Hz
Nominal voltage range AC 19.2...264 V / DC 19.2...137.5 V
Power consumption in operation 20 W
Power consumption in rest position 6W
Power consumption for wire sizing with 24 V 20 VA / with 230 V 52 VA
Auxiliary switch 2 x SPDT, 1 x 10° / 1 x 0...90° (ex works 85°)
Switching capacity auxiliary switch 1 mA...3 (0.5 inductive) A, AC 250 V
Connection supply Terminals 2.5 mm²
Connection control Terminals 1.5 mm²
Connection auxiliary switch Terminals 2.5 mm²
Parallel operation Yes (note the performance data)
Functional data Torque motor 160 Nm (parameterized for D6250W/WL)
Communicative control MP-Bus
BACnet MS/TP (Details see seperate document
“PICS”)
Positioning signal Y DC 0...10 V
Positioning signal Y note Input impedance 100 kΩ
Operating range Y DC 2...10 V
Operating range Y variable DC 0.5...10 V
4...20 mA
Position feedback U DC 2...10 V
Position feedback U note Max. 0.5 mA
Position feedback U variable DC 0.5...10 V
Position accuracy ±5%
Manual override with hand crank, can be fixed in any position
Running time motor 35 s / 90°
Motor running time variable 30...120 s
Sound power level motor 68 dB(A)
Position indication Mechanically (integrated)
Safety Protection class IEC/EN II reinforced insulation
Protection class UL II reinforced insulation
Protection class auxiliary switch IEC/EN II reinforced insulation
Degree of protection IEC/EN IP66 + IP67
Degree of protection NEMA/UL NEMA 4X, UL Enclosure Type 4X
EMC CE according to 2014/30/EU
Low voltage directive CE according to 2014/35/EU
Certification IEC/EN IEC/EN 60730-1 and IEC/EN 60730-2-14
Certification UL cULus according to UL 60730-1A, UL 60730-2-
14 and CAN/CSA E60730-1:02
Mode of operation Type 1
Rated impulse voltage supply 4 kV
Rated impulse voltage control 0.8 kV
Rated impulse voltage auxiliary switch 2.5 kV
Control pollution degree 3
Ambient temperature -30...50°C
Non-operating temperature -40...80°C
Ambient humidity 95% r.h., non-condensing
Maintenance Maintenance-free

www.belimo.eu PRCA-BAC-S2-T-250 • en-gb • 2017-03-30 • subject to changes 1

 Rotary actuator, modulating, communicative, AC 24...240
PRCA-BAC-S2-T-250 V / DC 24...125 V, 160 Nm, Running time motor 35 s

Technical data
Mechanical data Connection flange F07 (F05 only with accessory)

Weight Weight 5.8 kg

Safety notes
• This device has been designed for use in stationary heating, ventilation and air

! conditioning systems and must not be used outside the specified field of application,
especially in aircraft or in any other airborne means of transport.
• Caution: Power supply voltage!
• Only authorised specialists may carry out installation. All applicable legal or
institutional installation regulations must be complied during installation.
• Apart from the connection box, the device may only be opened at the manufacturer’s
site. It does not contain any parts that can be replaced or repaired by the user.
• The device contains electrical and electronic components and must not be disposed
of as household refuse. All locally valid regulations and requirements must be
observed.

Product features
Fields of application The actuator is particularly suitable for utilisation in outdoor applications and is
protected against the following weather conditions:
- UV radiation
- dirt / dust
- rain / snow
- Humidity
Converter for sensors Connection option for two passive sensors. This means the analogue sensor signal
can be easily digitised and transferred via field bus to the higher level system.
Parameterisable actuators The factory settings cover the most common applications.
The Belimo Assistant App is required for parameterisation via Near Field
Communication (NFC) and simplifies commissioning. Moreover, it provides a variety of
diagnostic options.
The ZTH EU service tool provides a selection of both diagnostic and setting options.
Simple direct mounting Simple direct mounting on the butterfly valve. The mounting orientation in relation to
the butterfly valve can be selected in 90° (angle) increments.
Manual override The valve can be manually operated using a hand crank. Unlocking is carried out
manually by removing the hand crank.
Internal heating An internal heater prevents condensation buildup.
Thanks to the integrated temperature and humidity sensor the built-in heater
automatically switches on and off.
High functional reliability The actuator is overload protected, requires no limit switches and automatically stops
when the end stop is reached.
Flexible signalization The actuator has one auxiliary switch with a fixed setting (10°) and one adjustable
auxiliary switch (0...90°).

Accessories

Description Type
Gateways Gateway MP for BACnet MS/TP, AC/DC 24 V UK24BAC
Gateway MP to Modbus RTU, AC/DC 24 V UK24MOD
Gateway MP to LonWorks, AC/DC 24 V, LonMark certified UK24LON
Gateway MP to KNX, AC/DC 24 V, EIBA certified UK24EIB
Description Type
Electrical accessories Connection cable 5 m, A+B: RJ12 6/6, To ZTH/ZIP-USB-MP ZK1-GEN
Description Type
Mechanical accessories Position indicator and tappet shaft, F07, square, SW 17 ZPR01
Tappet shaft, F07, square, SW 17 ZPR02
Position indicator and tappet shaft, F05, square, SW 14 ZPR03

2 PRCA-BAC-S2-T-250 • en-gb • 2017-03-30 • subject to changes www.belimo.eu

 Rotary actuator, modulating, communicative, AC 24...240
PRCA-BAC-S2-T-250 V / DC 24...125 V, 160 Nm, Running time motor 35 s

Accessories

Description Type
Retrofit adapter kit, F05/F07, flat head/ square, SW 17 ZPR05
Retrofit adapter kit, F05/F07, square 45° turned, SW 14 ZPR06
Retrofit adapter kit with ring, F07, square 45° turned, SW 17 ZPR08
Retrofit adapter kit with ring, F07, flat head/ square, SW 14 ZPR09
Retrofit adapter kit, F05/F07, flat head/ square, SW 14 ZPR10
Retrofit adapter kit, F05/F07, square 45° turned, SW 18 ZPR11
Retrofit adapter kit, F05/F07, flat head/ square, SW 16 ZPR12
Hand crank for PR-actuator ZPR20
Description Type
Service Tools Smartphone app for easy commissioning, parameterising and Belimo Assistant
maintenance App
Service tool for parametrisable and communicative Belimo actuators / ZTH EU
VAV controller and HVAC performance devices
Description Type
Sensors Duct/Immersion Temperature Sensor 50 mm x 6 mm PT1000 01DT-1BH
Duct/Immersion Temperature Sensor 100 mm x 6 mm PT1000 01DT-1BL
Duct/Immersion Temperature Sensor 150 mm x 6 mm PT1000 01DT-1BN
Duct/Immersion Temperature Sensor 200 mm x 6 mm PT1000 01DT-1BP
Duct/Immersion Temperature Sensor 300 mm x 6 mm PT1000 01DT-1BR
Duct/Immersion Temperature Sensor 450 mm x 6 mm PT1000 01DT-1BT
Duct/Immersion Temperature Sensor 50 mm x 6 mm Ni1000 01DT-1CH
Duct/Immersion Temperature Sensor 100 mm x 6 mm Ni1000 01DT-1CL
Duct/Immersion Temperature Sensor 150 mm x 6 mm Ni1000 01DT-1CN
Duct/Immersion Temperature Sensor 200 mm x 6 mm Ni1000 01DT-1CP
Duct/Immersion Temperature Sensor 300 mm x 6 mm Ni1000 01DT-1CR
Duct/Immersion Temperature Sensor 450 mm x 6 mm Ni1000 01DT-1CT

Electrical installation

Notes • Caution: Power supply voltage!

! • Parallel connection of other actuators possible. Observe the performance data.
• The main power supply for the actuator and for the auxiliary switches shall be
from the same phase.
• The wiring of the line for BACnet (MS/TP) has to be carried out in accordance
with applicable RS485 regulations.

Wiring diagrams

AC 24...240 V / DC 24...125 V Modulating control

N L
GND
N L DC (0)2...10 V
DC 2...10 V
+24VDC Out

T1 Com

T2 Com

N L Y1 Y2 (N) N L Y1 Y2 (N)
U5/MP
- Com

Com

D+
Y3

T2
T1

D-

Power Power Control Sensor RS485

www.belimo.eu PRCA-BAC-S2-T-250 • en-gb • 2017-03-30 • subject to changes 3

 Rotary actuator, modulating, communicative, AC 24...240
PRCA-BAC-S2-T-250 V / DC 24...125 V, 160 Nm, Running time motor 35 s

Electrical installation
Connection auxiliary switch

230 V + 230 V
24 V + 24 V

230 V + 24 V
24 V + 230 V

S1 S2 S3 S4 S5 S6

A 10% B 0...100%

N L
+24VDC Out

T1 Com

T1 Com

T2 Com

N L Y1 Y2 (N)
U5/MP
Y3Out
- Com

Com

D+
T2
T1

D-

Power Control Sensor RS485

Power supply must not be connected

to the signal terminals!

Follow-up control (position-dependent)

N L

GND
DC (0)2...10 V
DC 2...10 V
+24VDC Out

+24VDC Out

N L Y1 Y2 (N) N L Y1 Y2 (N)
U5/MP

U5/MP
- Com

- Com
Y3

Y3

Power Control Power Control

4 PRCA-BAC-S2-T-250 • en-gb • 2017-03-30 • subject to changes www.belimo.eu

 Rotary actuator, modulating, communicative, AC 24...240
PRCA-BAC-S2-T-250 V / DC 24...125 V, 160 Nm, Running time motor 35 s

Functions
Functions for actuators with specific parameters (Parametrisation with Belimo Assistant App necessary)

Open-close control
N L N L

GND GND

DC 2...10 V DC 2...10 V

+24VDC Out
+24VDC Out

N L Y1 Y2 (N) N L Y1 Y2 (N)

U5/MP
U5/MP

- Com
- Com

Y3
Y3

Power Y1 Y2 Control Power Y1 Y2 Control

3-point control
N L

GND

DC 2...10 V

0
+24VDC Out

N L Y1 Y2 (N)
U5/MP
- Com

Y3

Power Y1 Y2 Control

Control 4...20 mA
N L
(-)
4...20 mA
(+)
DC 2...10 V
+24VDC Out

T1 Com

T2 Com

N L Y1 Y2 (N)
U5/MP
- Com

Com

D+
Y3

T2
T1

D-

Power Control Sensor RS485

Positioner SG..

N L SGA24
- + Y Z SGF24
1 2 3 4 SGE24
+24VDC Out

T1 Com

T2 Com

N L Y1 Y2 (N) Note
U5/MP
- Com

Com

Maximum output power «+ 24VDC

D+
Y3

T2
T1

D-

out» 1.2 W @ 50 mA!

Power Control Sensor RS485 A separate safety transformer must
be used for higher performance!

www.belimo.eu PRCA-BAC-S2-T-250 • en-gb • 2017-03-30 • subject to changes 5

 Rotary actuator, modulating, communicative, AC 24...240
PRCA-BAC-S2-T-250 V / DC 24...125 V, 160 Nm, Running time motor 35 s

Functions
Connection on the MP-Bus

GND
A)
MP

N L
+24VDC Out

T1 Com

T2 Com

N L Y1 Y2 (N)
U5/MP
- Com

Com

D+
Y3

T2
T1

D-
Power Control Sensor RS485
A) Additional actuators (max. 8)

Network topology

There are no restrictions for the

network topology (star, ring, tree or
mixed forms are permitted).
Supply and communication in one
and the same 3-wire cable
• no shielding or twisting necessary
• no terminating resistors required

Connection of passive sensors (BACnet only)

N L

1) 2)
+24VDC Out

T1 Com

T2 Com

N L Y1 Y2 (N)
U5/MP

200 Ω...2 kΩ 0.1 Ω

- Com

Com

1) Resistance range
D+
Y3

T2
T1

D-

2 kΩ...10 kΩ 1Ω 2) Resolution
Power Control Sensor RS485 - Suitable for Ni1000 and PT1000
10 kΩ...55 kΩ 10 Ω
- Suitable Belimo types 01DT-…

6 PRCA-BAC-S2-T-250 • en-gb • 2017-03-30 • subject to changes www.belimo.eu

 Rotary actuator, modulating, communicative, AC 24...240
PRCA-BAC-S2-T-250 V / DC 24...125 V, 160 Nm, Running time motor 35 s

Functions
Connection BACnet MS/TP

GND
D+
D-

N L N L

N L Y1 Y2 (N) N L Y1 Y2 (N)
Com

Com
D+

D+
D-

D-
Power RS485 Power RS485

Connection BACnet MS/TP with analog setpoint (hybrid mode)

GND
D+
D-

GND

N L DC (0)2...10 V

DC 2...10 V
+24VDC Out

T1 Com

T2 Com

N L Y1 Y2 (N)
U5/MP
- Com

Com

D+
Y3

T2
T1

D-

Power Control Sensor RS485

www.belimo.eu PRCA-BAC-S2-T-250 • en-gb • 2017-03-30 • subject to changes 7

 Rotary actuator, modulating, communicative, AC 24...240
PRCA-BAC-S2-T-250 V / DC 24...125 V, 160 Nm, Running time motor 35 s

Operating controls and indicators

Auxiliary switch settings

S2 S3

S5 S6 S5 S6
! Note Perform settings on the actuator only in deenergised state.
A 10° S1 S4 S4
S2 S3
3
S5 S6 S5 S6

1 Gear disengagement
S4 S4

o
pe

n
Opening the manual override cover and adjusting the hand crank.
Manual override is possible.

2 Manual override control

2
Turn the hand crank until the desired switching position A is indicated and then
o
pe

remove the crank.

1
3 Auxiliary Switch
Opening the auxiliary switch adjustment cover and adjusting the hand crank.
Turn the crank until the arrow points to the vertical line

S1 S2 S3 S4 S5 S6
4 Terminals
4 Connect continuity tester to S4 + S5 or to S4 + S6.
If the auxiliary switch should switch in the opposite direction, rotate the hand
crank by 180°.

Push-buttons and display

5 Push-button and LED display green

Off: No power supply or malfunction
On: In operation
5 Press button: Triggers test run, followed by standard mode
Power
6 Push-button and LED display yellow
Status Off: Standard mode
6
Flickering: MP communication active
On: Test run active
Flashing: Request for addressing from MP master
Press button: Confirmation of the MP addressing

8 PRCA-BAC-S2-T-250 • en-gb • 2017-03-30 • subject to changes www.belimo.eu

 Rotary actuator, modulating, communicative, AC 24...240
PRCA-BAC-S2-T-250 V / DC 24...125 V, 160 Nm, Running time motor 35 s

Service
NFC connection Belimo equipment marked with the NFC logo can be operated with the “Belimo
Assistant App”.

Requirement:
- NFC-capable Android smartphone
- Belimo Assistant App (Google Play Store)

Align smartphone on the actuator so that both NFC antennas are superposed.

Service Tools connection The actuator can be parameterised by the ZTH EU via the service socket.

MP
USB

i esc   OK

www.belimo.eu PRCA-BAC-S2-T-250 • en-gb • 2017-03-30 • subject to changes 9

 Rotary actuator, modulating, communicative, AC 24...240
PRCA-BAC-S2-T-250 V / DC 24...125 V, 160 Nm, Running time motor 35 s

Dimensions [mm]
Dimensional drawings

>100
137
223
60 259

pe
o
n

202
pe
o
n

319

Further documentation
• Overview Valve-actuator combinations
• Data sheets for butterfly valves
• Installation instructions for actuators and/or butterfly valves
• General notes for project planning
• Overview MP Cooperation Partners
• Tool connections
• Introduction to MP-Bus Technology

10 PRCA-BAC-S2-T-250 • en-gb • 2017-03-30 • subject to changes www.belimo.eu