13.

56Mhz Mifare - Rfid Read Write Module

User Manual
1. Mifare Standard
1024 bytes EEPROM, divided into 16 sectors with 64 bytes on each sector 100,000 write endurance cycles 10 years data retention ISO 14443 A 13.56MHz transponder frequency 106 kbit baud rate Bit-wise anti-collision Up to 10 cm operating distance 4 byte unique serial number Random number generator 2 bytes access key per sector Individual access condition for each sector Purse functionality

2. Technical Specification
Power supply: 5V, 80-100mA Interface: RS232 or TTL232 Transmission speed: 19200 bps Dimensions: 60*40mm R/W distance of up to 60mm (up to 100mm with bigger antenna size), depending on TAG Storage temperature: -40 C ~ +85 C Operating temperature: 0 C ~ +70 C

3. Communication setting
The communication protocol is byte oriented. Both sending and receiving bytes are in hexadecimal format. The communication parameters are as follows, Baud rate: 19200 bps Data: 8 bits Stop: 1 bit Parity: None

Flow control: None

4 Dimension

Pin 7 DIMENSION Pin 1

Connector pin assignment NO Define 1 Reserve 2 Reserve 3 VCC(+5V) 4 GND 5 RX 6 TX 7 VCC(+5V)

5.

6.
Transmission rate Data format Data package Head Length Node ID Function Code Data XOR Default 19200 N 8 1

Binary HEX hexadecimal

COMMAND :
Data length XOR SUM

(Byte)
Head Length 02 02 Fixed: 0xAA , 0xBB There are several effective bytes that including XOR follows this column. Node ID 02 Destination Node Address Number. xx xx: Low byte first 00 00: Broadcast to each reader. Function code Data XOR 00~D0 01 02 It will be transmission ability of each different command . Low byte frist Data length is not fixed, according to its purpose. XOR each byte from Node ID to Last Data byte with 0xFF. X S S X S X S FF 00

REPLY DATA FORMAT :

(Byte)
Head Length 02 02 Fixed: 0xAA , 0xBB There are several effective bytes that including XOR follows this column. Node ID 02 Destination Node Address Number. xx xx: Low byte first 00 00: Broadcast to each reader. Function code Status Data XOR 1 00~D0 01 02 It will be transmission ability of each different command . Low byte frist Reply result , if succeed is 0 ,other fail . Data length is not fixed, according to its purpose. XOR each byte from Node ID to Last Data byte

NOTE: if from Length to XOR have a data is AA then should follow a data 0x00 ,but length dont changed. While a command send and after 100ms no reply then consider this command failed .

Command List 1 Initialize port 0x0101 2 Set device node number : 0x0102 3 Read device node number : 0x0103 4 Read device Mode : 0x0104 5 Set buzzer beep: 0x0106 6 Set Led color : 0x0107 7 Set reader working status : 0x0108 8 Set antenna status 0x010c 9 10 11 12 13 14 15 16 17 Mifare Request , 0x0201 Mifare anticollision , 0x0202: Mifare Select 0x0203: Mifare Hlta , 0x0204: Mifare Authentication1 0x0206 : Mifare Authentication2 0x0207: Mifare Read 0x0208: Mifare Write 0x0209: Mifare Initval 0x020A:

18 19 20 21 22 23 24 25

Mifare Read Balance 0x020B: Mifare Decrement 0x020C: Mifare Increment 0x020D: Mifare Restore 0x020E: Mifare Transfer 0x020F Mifare UltraLight Anticoll 0x0212: Mifare UltraLight Write 0x0213: Write key store in RC500 EEPROM

7. COMMAND
1 Initialize port 0x0101 Function set baud rate Format aa bb 06 00 00 01 01 Baud_para xor Chk Baud_parameter 0 = 4800; 1 = 9600; 2 = 14400; 3 = 19200; 4 = 28800; 5 = 38400; 6 = 57600; 7 = 115200; sample Host To Reader; aa bb 06 00 00 00 01 01 03 03

Set Baud Rate as 19200

Respond: aa bb 06 00 bf ff 01 01 00 40 2 3 4 Set device node number : 0x0102 Read device node number : 0x0103 not use of this version not use of this version

Read device Mode : 0x0104 function read device mode and version Host to Reader : aa bb 05 00 00 00 04 01 05 Respond: aa bb 12 00 52 51 04 01 00 43 52 35 30 30 4c 52 2d 31 32 30 33 11 C R5 0 0 LR- 1 2 03 Set buzzer beep: 0x0106 Function beep format aa bb 06 00 00 00 06 01 Delay XOR Delay*10ms beep time XOR is xor check Sample Host to Reader : aa bb 06 00 00 00 06 01 64 63 Respond : aa bb 06 00 52 51 06 01 00 04 Set Led color : 0x0107

Host To Reader; aa bb 06 00 00 00 07 01 03 05 // set Red&green LED on Respond: aa bb 06 00 bf bf 07 01 00 06

7 8

Set reader working status : 0x0108 not use in this device Set antenna status 0x010c Host To Reader; aa bb 06 00 00 00 0c 01 00 0D //set antenna off
Tenth data is Antenna status parameter 0 = Close Filed 1= Open Filed.

9.

Mifare Reauest , 0x0201 Function Request Type a Card Format aa bb 06 00 00 00 01 02 req_code XOR req_code=Request mode req_code=0x52: request all Type A card In filed req_code=0x26: request idle card sample Host To Reader: aa bb 06 00 00 00 01 02 52 51 Respond : aa bb 08 00 52 51 01 02 00 04 00 04

10.

Mifare anticollision , 0x0202: Function card anticollision Format aa bb 05 00 00 00 02 02 00 Respond aa bb 0a 00 52 51 02 02 00 46 ff a6 b8 a4 46 ff a6 b8 is card serial number

11 Mifare Select 0x0203: Function Select card Format aa bb 09 00 00 00 03 02 xx xx xx xx XOR Ninth to twelfth is card serial number Sample Host to Reader : aa bb 09 00 00 00 03 02 46 ff a6 b8 a6 Respond : aa bb 07 00 52 51 03 02 00 08 0a 12. Mifare Hlta , 0x0204: Function Hlta card Host to reader aa bb 05 00 00 00 04 02 06

Respond

aa bb 06 00 52 51 04 02 00 05

13. Mifare Authentication1 0x0206 : Function authenticate Card (Key Stroe in RC500) Format aa bb xx 00 00 00 06 02 Auth_mode Block KeyEE CHK Auth_mode=Authenticate mode,0x60: Key A ,0x61: Key B Block= Authenticate block KeyEE = Key store in RC500 EEPROM group from 0 to 31 total 32 Sample Host to Reader : aa bb 08 00 00 00 06 02 60 04 01 61 Authenticate Block 4 Key = group 01 Respond : aa bb 06 00 11 12 06 02 00 07 14. Mifare Authentication2 0x0207: Function authenticate Card Format aa bb xx 00 00 00 07 02 Auth_mode Block xx xx xx xx xx xx XOR Auth_mode= Authenticate mode ,0x60: KEY A ,0x61: KEY B Block = Authenticate block Sample Host to Reader : aa bb 0d 00 00 00 07 02 60 04 ff ff ff ff ff ff 61 Authenticate Block 4 Key A = FF FF FF FF FF FF Respond : aa bb 06 00 52 51 07 02 00 06 15. Mifare Read 0x0208: Function Read block Format aa bb 06 00 00 00 08 02 Block XOR Block = which block want read Sample Host to Reader : aa bb 06 00 00 00 08 02 04 0e Respond aa bb 16 00 52 51 08 02 00 00 00 00 00 00 00 00 00 00 00 00 00 12 34 56 78 01 Tenth to sixteenth byte is Data 16. Mifare Write 0x0209: Function write block Format aa bb 16 00 00 00 09 02 Block D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 Da Db Dc Dd De Df XOR Sample write data to Block4 Host to Reader aa bb 16 00 00 00 09 02 04 00 00 00 00 00 00 00 00 00 00 00 00 12 34 78 56 07 Respond: aa bb 06 00 52 51 09 02 00 08 17. Mifare Initval 0x020A: initialize purse Function aa bb 0a 00 00 00 0a 02 Block V0 V1 V2 V3 XOR Format 18. Mifare Read Balance 0x020B: Function read balance Format aa bb 06 00 00 00 0B 02 Block XOR Return four byte balance 19 Mifare Decrement 0x020C:

Function Format

decrease balance aa bb 0a 00 00 00 0c 02 Block V0 V1 V2 V3 XOR

20. Mifare Increment 0x020D: increase balance Function aa bb 0a 00 00 00 0D 02 Block V0 V1 V2 V3 XOR Format 21. Mifare Restore 0x020E: Function Restore a mifare_one block data to buffer Format aa bb 06 00 00 00 0E 02 Block XOR 22. Mifare Transfer 0x020F Function Transfer buffer data to a block Format aa bb 06 00 00 00 0F 02 Block XOR 23. Mifare UltraLight Anticoll 0x0212: Function UltraLight anticollision ,respond ultralight ID Format aa bb 05 00 00 00 12 02 CHK Sample Host to Reader: aa bb 05 00 00 00 12 02 10 Respond : aa bb 0d 00 52 51 12 02 00 04 1f ae 11 14 7a 00 d9 04 1f ae 11 14 7a 00 is card serial number 24. Mifare UltraLight Write 0x0213: Function write mifare Ultralight Format aa bb 0a 00 00 00 13 02 Page D0 D1 D2 D3 XOR Page which page want write data D0D3 data XOR xor check Sample Host to Reader : aa bb 0a 00 00 00 13 02 04 88 88 88 88 15 Respond: aa bb 06 00 52 51 13 02 00 12 25. Write key store in RC500 EEPROM Format aa bb xx 00 00 00 16 02 Auth_mode group xx xx xx xx xx xx XOR Auth_mode= 0x60: KEY A ,0x61: KEY B (ignore in this command) Group = 031 write RC500 Eeprom Address from 0x80 to 0x1FF group xx xx xx xx xx xx = KEY should be writed to EEPROM Sample Host to Reader : aa bb 0d 00 00 00 16 02 60 01 ff ff ff ff ff ff 75 Write group 01 Key = FF FF FF FF FF FF Respond : aa bb 06 00 11 12 16 02 00 17 total 32