R32

#290

BLN-006TC1/BLN-012TC1
BLN-018TC1/BLN-012TC3/BLN-018TC3

Air Source Heat Pump

Heat Pump for Heating & Cooling & DHW

Please read this manual carefully before using it and keep it in a safe place.

1
 Note

1. Please read the instruction manual carefully before installation or operation.

2. The heat pump must be installed by a professional installer.
3. Please follow the instruction manual strictly when installing the heat pump
4. If any update on the product, this instruction manual is subject to change without notice
5. If the heat pump is installed where is vulnerable to lightning strikes, it is necessary to take lightning
protection measures; if the heat pump is turned off in the winter, please be sure to drain the water
in the system to prevent cold water from swelling and causing system damage.

Contents

User Instruction-------------------------------------------------------------------1
Operation Instructions---------------------------------------------------------12
Dimension-------------------------------------------------------------------------19
Installation------------------------------------------------------------------------23
Commissioning and Maintenance ---------------------------------------34
Trouble Analysis-----------------------------------------------------------------36
Specification----------------------------------------------------------------------39
After-sale ervice-----------------------------------------------------------------41
Appendix---------------------------------------------------------------- 42

2
 User Instructions

1. Please use an electrical leakage switch, 2. Make sure that the leakage protection switch
otherwise, there may be electric shock, fire, etc. is securely connected. If the wiring is not secure,
it may cause electric shock, heat, or fire.

Test Button

3. Do not operate with a wet hand, 4. Do not insert your fingers or any stick into the
otherwise, there may cause electric inside of the ventilation area, otherwise, harm
shock. will be caused.

Danger

3
R290 Warning

⚫ This appliance uses R290 (propane) refrigerant, which is a

flammable gas and must be serviced by an authorized person.
⚫ WARNING Risk of fire/flammable material. If the refrigerant is
leaking, switch off the unit at the mains and contact the service
agent.
⚫ DO NOT store chemicals or flammable materials near this
appliance.
⚫ NEVER use a flammable spray such as hair spray, paint, etc near
this unit as this may cause a fire.
⚫ Avoid risk of injury from contact with refrigerant if you notice a
leak.
⚫ If you suspect the refrigerant is leaking then:
⚫ Do not smoke.
⚫ Do not operate electrical equipment. Isolate the device.
⚫ End of life recycling
The refrigerant must not enter the atmosphere. Only have the
refrigerant removed by qualified professional.

4
1. Precautions
Please make sure that you have read this manual before using our air source heat pump. In the
“User Information” chapter, “User Information” provides essential safety information. Please be
sure to follow the instruction strictly.

Wrong operations are likely to cause serious consequences such as death, serious
Warning
injury, or major accidents

Improper operation may result in a safety accident, damage to the machine, or affect
Note the function of the machine.

Please read the labels on the machine carefully. If abnormal conditions such as abnormal noise, odor, smoke,
temperature rise, electric leakage, fire, etc. are found during use, please cut off the power immediately and
contact our local customer service center or dealer in time to repair it. Contact the local fire and emergency
department immediately if necessary.

Warning

1) This Machine is not allowed to be installed by the user. A professional installer must install it,
Otherwise cause safety accidents or affects the machine’s performance.
2) Without professional guidance, non-professionals are not allowed to disassemble the machine.
Otherwise, accidents or damage may be caused to the device.
3) Do not use or store flammable materials such as hair spray, paint, gasoline, alcohol, etc., around
the machine. Otherwise, fire may be caused.
4) The machine’s main power switch should be placed where that child cannot reach to prevent
children from playing with the power switch.
5) Do not spray water or other liquids on the machine. Otherwise, danger may occur.
6) Do not touch the machine with wet hands. Otherwise, it may cause an electric shock.
7) In thunderstorms, please disconnect the main power switch off the machine. Otherwise, lightning
may cause danger or damage to the device.
8) The machine needs to use a separate power switch to avoid sharing the same circuit with other
electrical appliances, supply the power to the machine vice the specified power cable, and use
the proper breaker with the electric leakage protection required.
9) The machine must be installed with a specified grounding wire. Do not connect the grounding
wire to the gas pipe, water pipe, lightning conductor, or telephone, and the machine must be
grounded reliably to avoid any electric shock.
10) Do not disconnect the power supply when the machine is running.
11) When the machine is not used for a long time, please disconnect the main power switch to avoid
accidents.
12) If the ambient temperature is below 0 ℃, it is forbidden to cut off the power supply. If the power
is turned off unexpectedly under these conditions, drain the water inside the pipeline.

5
 Note

1) Do not put your hands or other objects into the air outlet of the machine. Otherwise, the fan
running at high speed may cause harm.
2) Do not remove the fan cover. Otherwise, the fan running at high speed may cause injury to you
or others.
3) Lightning and other sources of electromagnetic radiation may have a remarkable effect on the
machine. Turn off the power and then restart the device if it does affect it.
4) Make sure the water supply is frequent. Otherwise, the machine may be damaged.
5) Do not restart the machine frequently. Otherwise, the device may be damaged.
6) The operating parameters of the machine and the set value of the protection device have been
selected by the manufacturer. Users should not change the set value arbitrarily and do not short
the wire of the protection device. Otherwise, the machine may be damaged due to improper
protection.
7) To avoid the freezing of the water system pipeline when the machine is deactivated in an
environment below 0 ℃, please keep the machine standby state. If the device is out of service
for a long time, it is recommended that the user drain the water out of the water system and
disconnect the power supply.
8) Please perform regular maintenance on the machine as required by the instructions to ensure the
device is in good operating condition.

2. Refrigerant Precaution
1) Do not use means to accelerate the defrosting process or to clean, other than those
recommended by the manufacturer.
2) The appliance shall be stored in a room without continuously operating ignition sources (for
example open flames, an operating gas appliance, or an operating electric heater)
3) Do not pierce or burn.
4) Be aware that refrigerants may not contain an odor.
5) Appliance shall be installed, operated, and stored in a room with a floor area larger than X
m2
6) The installation of pipe-work shall be kept to a minimum of X m2
7) Spaces where refrigerant pipes shall be in compliance with national gas regulations.
8) Servicing shall be performed only as recommended by the manufacturer.
9) The appliance shall be stored in a well-ventilated area where the room size corresponds
to the room area as specified for operation.
10) All working procedures that affect safety means shall only be carried out by competent
persons.

3. Requirement of Flammable Refrigerant

1) Transport of equipment containing flammable refrigerants: Compliance with the transport
regulations
2) Marking of equipment using signs: Compliance with local regulations
3) Disposal of equipment using flammable refrigerants: Compliance with national regulations
4) Storage of equipment/appliances: The storage of equipment should be in accordance with the
manufacturer’s instructions.
5) Storage of packed (unsold) equipment: Storage package protection should be constructed such
that mechanical damage to the equipment inside the package will not cause a leak of the

6
 refrigerant charge. The maximum number of pieces of equipment permitted to be stored together
will be determined by local regulations.
6) Information on servicing:
i. Checks to the area
Prior to beginning work on systems containing flammable refrigerants, safety checks are
necessary to ensure that the risk of ignition is minimized. For repair to the refrigerating system,
the following precautions shall be complied with prior to conducting work on the system.
ii. Work Procedure
Work shall be undertaken under a controlled procedure so as to minimize the risk of flammable
gas or vapor being present while the work is being performed.
iii. General Work Area
All maintenance staff and others working in the local area shall be instructed on the nature of
the work being carried out. Work in confined spaces shall be avoided. The area around the
workspace shall be sectioned off. Ensure that the conditions within the area have been made
safe by control of flammable material.
iv. Checking for the presence of refrigerant
The area shall be checked with an appropriate refrigerant detector prior to and during work, to
ensure the technician is aware of potentially flammable atmospheres. Ensure that the leak
detection equipment being used is suitable for use with flammable refrigerants, i.e. non-
sparking, adequately sealed or intrinsically safe.
v. Presence of fire extinguisher
If any hot work is to be conducted on the refrigeration equipment or any associated parts,
appropriate fire extinguishing equipment shall be available to hand. Have a dry powder or CO2
fire extinguisher adjacent to the charging area.
vi. No ignition sources
No person carrying out work in relation to a refrigeration system that involves exposing any
pipework that contains or has contained flammable refrigerant shall use any sources of ignition
in such a manner that it may lead to the risk of fire or explosion. All possible ignition sources,
including cigarette smoking, should be kept sufficiently far away from the site of installation,
repairing, removal, and disposal, during which flammable refrigerant can possibly be released
to the surrounding space. Prior to work taking place, the area around the equipment is to be
surveyed to make sure that there are no flammable hazards or ignition risks. “No Smoking”
signs shall be displayed.
vii. Ventilated area
Ensure that the area is in the open or that it is adequately ventilated before breaking into the
system or conducting any hot work. A degree of ventilation shall continue during the period
that the work is carried out. The ventilation should safely disperse any released refrigerant and
preferably expel it externally into the atmosphere.
viii. Checks to the refrigeration equipment
Where electrical components are being changed, they shall be fit for the purpose and to the
correct specification. At all times the manufacturer’s maintenance and service guidelines shall
be followed. If in doubt consult the manufacturer’s technical department for assistance. The
following checks shall be applied to installations using flammable refrigerants:
--The charge size is in accordance with the room size within which the refrigerant containing
parts are installed;
--The ventilation machinery and outlets are operating adequately and are not obstructed;
--If an indirect refrigerating circuit is being used, the secondary circuit shall be checked for the
presence of refrigerant;
--Marking of the equipment continues to be visible and legible. Markings and signs that are
illegible shall be corrected;

7
 --Refrigeration pipes or components are installed in a position where they are unlikely to be
exposed to any substance which may corrode refrigerant-containing components unless the
components are constructed of materials that are inherently resistant to being corroded or are
suitably protected against being so corroded.
ix. Checks to electrical devices
Repair and maintenance to electrical components shall include initial safety checks and
component inspection procedures. If a fault exists that could compromise safety, then no
electrical supply shall be connected to the circuit until it is satisfactorily dealt with. If the fault
cannot be corrected immediately but it is necessary to continue operation, an adequate
temporary solution shall be used. This shall be reported to the owner of the equipment so all
parties are advised.
Initial safety checks shall include:
• That capacitor is discharged: this shall be done in a safe manner to avoid the possibility of
sparking;
• That there no live electrical components and wiring are exposed while charging, recovering,
or purging the system;
• That there is continuity of earth bonding.
7) Repairs sealed components:
a) During repairs to sealed components, all electrical supplies shall be disconnected from the
equipment being worked upon prior to any removal of sealed covers, etc. If it is absolutely
necessary to have an electrical supply to equipment during servicing, then a permanently
operating form of leak detection shall be located at the most critical point to warn of a
potentially hazardous situation.
b) Particular attention shall be paid to the following to ensure that by working on electrical
components, the casing is not altered in such a way that the level of protection is affected. This
shall include damage to cables, an excessive number of connections, terminals not made to
original specification, damage to seals, incorrect fitting of glands, etc. Ensure that apparatus is
mounted securely. Ensure that seals or sealing materials have not degraded such that they no
longer serve the purpose of preventing the ingress of flammable atmospheres. Replacement
parts shall be in accordance with the manufacturer’s specifications.
NOTE: The use of silicone sealant may inhibit the effectiveness of some types of the leak.
8) Repair to intrinsically safe components
Do not apply any permanent inductive or capacitance loads to the circuit without ensuring that
this will not exceed the permissible voltage and currently permitted for the equipment in use.
Intrinsically safe components are the only types that can be worked on whillivingve in the
presence of a flammable atmosphere. The test apparatus shall be at the correct rating. Replace
components only with parts specified by the manufacturer. Other parts may result in the ignition
of refrigerant in the atmosphere from a leak.
9) Cabling
Check that cabling will not be subject to wear, corrosion, excessive pressure, vibration, sharp
edges or any other adverse environmental effects. The check shall also take into account the
effects of aging or continual vibration from sources such as compressors or fans.
10) Detection of flammable refrigerants
Under no circumstances shall potential sources of ignition be used in the searching for or
detection of refrigerant leaks. A halide torch (or any other detector using a naked flame) shall not
be used.
11) Leak detection methods
The following leak detection methods are deemed acceptable for systems containing flammable
refrigerants.
Electronic leak detectors shall be used to detect flammable refrigerants, but the sensitivity may

8
 not be adequate or may need re-calibration. (Detection equipment shall be calibrated in a
refrigerant-free area.) Ensure that the detector is not a potential source of ignition and is suitable
for the refrigerant used. Leak detection equipment shall be set at a percentage of the LFL of the
refrigerant and shall be calibrated to the refrigerant employed and the appropriate percentage of
gas (25 % maximum) is confirmed.
Leak detection fluids are suitable for use with most refrigerants but the use of detergents
containing chlorine shall be avoided as the chlorine may react with the
refrigerant and corrode the copper pipe-work.
12) Removal and evacuation
When breaking into the refrigerant circuit to make repairs – or for any other purpose –
conventional procedures shall be used. However, it is important that best practice is followed
since flammability is a consideration. The following procedure shall be adhered to:
• Remove refrigerant;
• Purge the circuit with inert gas;
• Evacuate;
• Purge again with inert gas;
• Open the circuit by cutting or brazing.
The refrigerant charge shall be recovered into the correct recovery cylinders. The system shall be
“flushed” with OFN to render the unit safe. This process may need to be repeated several times.
Compressed air or oxygen shall not be used for this task.
Flushing shall be achieved by breaking the vacuum in the system with OFN and continuing to fill
until the working pressure is achieved, then venting to the atmosphere, and finally pulling down
to a vacuum. This process shall be repeated until no refrigerant is within the system. When the
final OFN charge is used, the system shall be vented down to atmospheric pressure to enable work
to take place. This operation is absolutely vital if brazing operations on the pipe-work are to take
place.
Ensure that the outlet for the vacuum pump is not close to any ignition sources and there is
ventilation available.
13) Charging procedures
In addition to conventional charging procedures, the following requirements shall be followed.
--Ensure that contamination of different refrigerants does not occur when using charging
equipment. Hoses or lines shall be as short as possible to minimize the amount of
refrigerant contained in them.
--Cylinders shall be kept upright.
--Ensure that the refrigeration system is earthed prior to charging the system with refrigerant.
--Label the system when charging is complete (if not already).
--Extreme care shall be taken not to overfill the refrigeration system.
--Prior to recharging the system, it shall be pressure tested with OFN. The system shall be leak
tested on completion of charging prior to commissioning. A follow-up leak test shall be carried
out prior to leaving the site.
14) Decommissioning
Before carrying out this procedure, it is essential that the technician is completely familiar with
the equipment and all its detail. It is recommended good practice that all refrigerants are
recovered safely. Prior to the task being carried out, an oil and refrigerant sample shall be taken
in case analysis is required prior to re-use of reclaimed refrigerant. It is essential that electrical
power is available before the task is commenced.
a) Become familiar with the equipment and its operation.
b) Isolate system electrically.
c) Before attempting the procedure ensure that:
• Mechanical handling equipment is available, if required, for handling refrigerant cylinders;

9
 • All personal protective equipment is available and being used correctly;
• The recovery process is supervised at all times by a competent person;
• Recovery equipment and cylinders conform to the appropriate standards.
d) Pump down refrigerant system, if possible.
e) If a vacuum is not possible, make a manifold so that refrigerant can be removed from various
parts of the system.
f) Make sure that cylinder is situated on the scales before recovery takes place.
g) Start the recovery machine and operate in accordance with manufacturer's instructions.
h) Do not overfill cylinders. (No more than 80 % volume liquid charge).
i) Do not exceed the maximum working pressure of the cylinder, even temporarily.
j) When the cylinders have been filled correctly and the process completed, make sure that the
cylinders and the equipment are removed from the site promptly and all isolation valves on the
equipment are closed off.
k) Recovered refrigerant shall not be charged into another refrigeration system unless it has been
cleaned and checked.
15) Labelling
Equipment shall be labeled stating that it has been decommissioned and emptied of refrigerant.
The label shall be dated and signed. Ensure that there are labels on the equipment stating the
equipment contains flammable refrigerant.
16) Recovery
When removing refrigerants from a system, either for servicing or decommissioning, it is
recommended good practice that all refrigerants are removed safely. When transferring
refrigerant into cylinders, ensure that only appropriate refrigerant recovery cylinders are
employed. Ensure that the correct number of cylinders for holding the total system charge is
available. All cylinders to be used are designated for the recovered refrigerant and labeled for that
refrigerant (i.e. special cylinders for the recovery of refrigerant). Cylinders shall be complete with
a pressure relief valve and associated shut-off valves in good working order. Empty recovery
cylinders are evacuated and, if possible, cooled before recovery occurs. The recovery equipment
shall be in good working order with a set of instructions concerning the equipment that is at hand
and shall be suitable for the recovery of flammable refrigerants. In addition, a set of calibrated
weighing scales shall be available and in good working order. Hoses shall be complete with leak-
free disconnect couplings and in good condition. Before using the recovery machine, check that
it is in satisfactory working order, has been properly maintained, and that any associated electrical
components are sealed to prevent ignition in the event of a refrigerant release. Consulting
manufacturer if in doubt.
The recovered refrigerant shall be returned to the refrigerant supplier in the correct recovery
cylinder, and the relevant Waste Transfer Note arranged. Do not mix refrigerants in recovery units
and especially not in cylinders. If compressors or compressor oils are to be removed, ensure that
they have been evacuated to an acceptable level to make certain that flammable refrigerant does
not remain within the lubricant. The evacuation process shall be carried out prior to returning the
compressor to the suppliers. Only electric heating to the compressor body shall be employed to
accelerate this process. When oil is drained from a system, it shall be carried out safely.

4. Other Safety
Thank you for choosing a heat pump. This is a heat pump capable of providing the ideal comfort for
your home, always with a suitable hydraulic installation. The unit is an air source heat pump for
space heating/cooling and a sanitary water heater for houses, apartment blocks, and small industrial
premises. Outdoor air is used as a heat source creating free energy to heat your home.
This manual forms an essential part of the product and it must be given to the user. Read the

10
 warnings and recommendations in the manual carefully, as they contain important information on
the safety, use, and maintenance of the installation.
This heat pump must be installed by qualified personnel only, in accordance with the legislation in
force and following the manufacturer’s instructions.
The start-up of this heat pump and any maintenance operations must be carried only by qualified
personnel only.
Incorrect installation of this heat pump could result in damage to people, animals or property, and
the manufacturer will not be held liable in such cases.
The following safety precautions should always be taken into account:
1) Be sure to read the following WARNING before installing the unit.
2) Be sure to observe the cautions specified here as they include important items related to safety.
3) After reading these instructions, be sure to keep them in a handy place for future reference.
4) Equipment shall contain the following identification:

Inflammable “ ” Read Carefully “ ” Professional Recycling “ “

11
 Operation Instruction

1. Control Panel

Current Mode

Water Temperature Temperature Setting

Time or fault display area

Timer
Power ON/OFF Up

Power ON/OFF Down

Change Mode
Heating/Cooling/DHW

2. Operation Instruction

Power On/Off

When the lock symbol is Long press 2s to turn off Long press 2s to turn on
displayed, press and the heat pump the heat pump
hold 5s to unlock the
screen

Mode Setting

Press M to switch mode

Cooling/Heating/DHW
12
Temperature Setting

If there is no operation or press the

on/off button within 5 seconds, the
setting temperature will be saved
automatically and return to the
homepage

Press the up button Press the down button

to raise the temperature to lower the temperature

Time Setting

Press the clock button for Press the clock key again, Press the up and down Press the clock button again to
1s to enter the current clock the hour area flashes keys to adjust the value enter the minute clock setting
setting

If there is no operation or press the

on/off button within 5 seconds, the
setting temperature will be saved
automatically and return to the
使用操作说明
Press the clock button Press the up and down homepage
again, the minute keys to adjust the value
area flashes

Scheduled Power On

Press and hold the clock Press the clock key again, Press the up and down Press the clock button again to
key for 5s to enter the the hour area flashes keys to adjust the value enter the minute clock setting
timer boot time setting

If there is no operation or press the

on/off button within 5 seconds, the
setting temperature will be saved
automatically and return to the
homepage. 使用操作说明
Press the clock button Press the up and down
Three timings can be set.
again, the minute keys to adjust the value
area flashes

13
 Status Search

Long press the down Enter the status search Adjust the status parameter serial
button for 5 s to enter page number in combination with the up
the status search page and down keys

ECO Mode

Unlock the case while holding down the ECO symbol lit
up button + down button to enter ECO
energy-saving mode

Pump forced evacuation mode

Press and hold the on/off button + up button When the water pump symbol flashes
at the same time in the unlocked state to enter the enter forced emptying mode
intelligent distribution mode

14
3. Temperature and Climate Curve Setting
Setting Climate Temperature Curve

Press the key for 1s to Set temperature Press and hold the M Enter the temperature curve
enter the temperature flashing button again for 5s setting status to enable or
setting interface disable the curve

Press the upper key Curve set successfully

1
again for 1s

When the climate temperature curve function is enabled, the user can select one of the eight curves in
the main interface; curve 4 is the default curve, and curve 6 is the ECO energy-saving curve.

4. Wi-Fi Setting
4.1 Software Download and Account Registration

4.1.1 Search for Smart Life in the app store on the mobile phone, and download and
install it.
4.1.2 Users who do not have an account can apply by clicking the "Create New User" function on
the login page.
4.1.3 Create a new account → Enter your cell phone number or email address, → get the verification
code → to enter the verification code → set the password → complete, in the following order.
4.1.4 After registration is complete, you need to create a family: create a family, → set the family
name → set the location → to add a room → ultimately, in the following order.
4.1.5 Click on the device name to enter the main interface of the device
1) Family name, which allows access to family management.
2) Adding devices.
3) Added room; click on it to view the devices added to that room.
4) Room management.

15
4.2 Connection (Intelligent Mode)

Manual Intelligent Distribution Network

In the unlocked state, press and hold the on/off button + up button Wifi signal flashes
at the same time to enter the intelligent distribution mode Enter distribution network status

Step 1
Open the "Smart Life" APP, login to the main interface, click the "lift" icon in the upper right corner
to add devices or "Add Device" in the interface, enter the device type selection, and select "Smart
Heat Pump (Wi-Fi)" in the "Main Appliance" device, enter the add device interface.

Step 2
Select Smart Heat Pump (Wi-Fi) and enter into the Wi-Fi connection interface, enter the Wi-Fi
password that the phone has been connected to (must be the same as the Wi-Fi connection to the
phone), click Next, and confirm that the line controller has selected the intelligent distribution mode,
" " icon is fast-flashing, click "Confirm that the indicator is flashing, then start adding devices
directly, click the "lift" icon to add devices.
Note: The icon flashes slowly when the Wi-Fi module is connected to the Wi-Fi hotspot.

Step 3
The system prompts "Add Device Successfully" and then the network is successfully distributed.
Click on the icon in this interface to change the device name, select the device installation location
(living room, main bedroom), and click Finish to enter the main interface of device operation.

4.3 Connection (AP Mode)

Manual AP Distribution Network

In the unlocked state, press and hold the on/off button + down button Wifi signal flashes
at the same time to enter the intelligent distribution mode Enter distribution network status

Step 1 and Step 2: Be consistent with the Intelligent Mode

Step 3
Select innovative heat pump (Wi-Fi) after entering into the Wi-Fi connection interface, enter the
phone has been connected to the (Wi-Fi) password (must be consistent with the Wi-Fi connection
to the phone), click next, confirm that the line controller has selected AP distribution mode, an icon

16
in the slow flashing state “ ”, click "Confirm that the indicator is in slow flashing,” then connect
the phone Wi-Fi to the device hotspot (as shown below), confirm that the connection hotspot is
correct to continue to the next step then directly begin to connect the device interface, find the
device → registers to the cloud → device initialization is complete.
Note: When the wire Wi-Fi module is connected to the Wi-Fi hotspot, the icon “ ” slows flashing.

Step 4 The same as the Intelligent Mode

Note: If the connection fails, manually enter the AP network configuration mode again and repeat
the preceding steps to connect again.

4.4 Software Function Operation

4.4.1 A device is automatically bound to a virtual gateway. The "My Home Heat Pump" (device name,
which can be changed) operation page is displayed.
Buy a ticket to enter the device operation page of "My Home Heat Pump" by clicking on "My Home
Heat Pump" in the "All Devices" screen of smart Life.
4.4.2 Modify device name and modify device location information Click "Name" to rename the
device name and "Location" to alter the device location.

4.5 Device Sharing

Share bound devices in the following sequence:

1) After successful sharing, the list is added to display the shared person.
2) To delete the shared user, long-press the selected user, and the deletion interface will pop up,
click "Delete"
3) User interface operations are as follows:
4) Enter the account of the shared user and click "Finish" to display the newly shared history in the
list of successful sharing
5) The interface of the shared person is as follows. The shared device received is displayed. Click in
to operate and control the device.

17
 Operation Parameter Query
Query Code Description Range
1 Compressor Running Frequency 0 ~ 150 Hz
2 Fan Motor Running Frequency 0 ~ 999 Hz
3 Electronic expansion valve steps 0 ~ 480 P
4 EVI valve steps 0 ~ 480 P
5 AC Input Voltage 0 ~ 500 V
6 AC Input Current 0 ~ 50 A
7 Compressor Phase Current 0 ~ 50 A
8 IPM temperature of the compressor -40 ~ 140 ℃
9 High-pressure saturation temperature -50 ~ 200 ℃
10 Low-pressure saturation temperature -50 ~ 200 ℃
11 External ambient temperature T1 -40 ~ 140 ℃
12 Outer coil (fin) T2 -40 ~ 140 ℃
13 Internal coil (plate heat exchanger) T3 -40 ~ 140 ℃
14 Gas Suction Temperature T4 -40 ~ 140 ℃
15 Gas Exhaust Temperature T5 0 ~ 150 ℃
16 Water Inlet Temperature T6 -40 ~ 140 ℃
17 Water Outlet Temperature T7 -40 ~ 140 ℃
18 Economizer Inlet Temperature T8 -40 ~ 140 ℃
19 Economizer Outlet Temperature T9 -40 ~ 140 ℃
20 Machine Tooling No. 0 ~ 120
21 Water tank temperature -40 ~ 140 ℃
Fluorine plate heat exchanger out
22 -40 ~ 140 ℃
temperature
23 Driver manufacturers 0 ~ 10
24 Water pump speed PWM 0 ~ 100%
25 Water flow 3 ~ 100 L/min
26 Return water temperature -40 ~ 140 ℃
27 Unit input voltage 0 ~ 500 V
28 Unit input current 0A ~ 99.99A
29 Unit input power 0 ~ 99.99KW
Total electricity consumption of the
30 0 ~ 9999 Kw.h
unit

Display Fault: When the machine has a fault, the fault is flashing in the timing area and the fault code is
displayed cyclically; when the fault is eliminated, the standard display is restored.

18
 Dimension
1. Dimension

Packed
Model
Dimensions (mm)

BLN-006TC1 1217*463*920

BLN-012TC1 1317*493*1020
BLN-012TC3 1317*493*1020

19
20
 Packed
Model
Dimensions (mm)
BLN-018TC1 1217*538*1570
BLN-018TC3 1217*538*1570

21
2. Explosive Diagram

Number Description Number Description

1 Front right panel 24 Compressor
2 Front left panel 25 Base panel Components
3 Air outlet grille 26 Plate heat exchanger
4 Baffle 27 Plate heat exchanger refrigerant
5 Maintenance panel 28 Plate heat exchanger
outlet inlet pipe
6 Fan blade 29 Plate heat exchanger refrigerant
7 Fan motor 30 Water
intakepump
pipe
8 Motor bracket 31 Drain pipe
9 Left-side column 32 Drain connector
10 Left-sidepanel 33 Safety valve
11 Probe Clamp 34 Expansion tank pipeline

22
 12 Plastic Waterproof Joint 35 Water pump inlet pipe
13 Junction Plate 2 36 Plate heat exchanger outlet pipe
14 Junction Plate 3 37 Flow switch
15 Right-side Plate 38 Auto exhaust valve
16 Clip 39 Fixed plate
17 Expansion tank 40 Waterproof connector
18 Expansion Tank Bracket 41 Terminal block bracket
19 Four-way valve assembly 42 Terminal block
20 Reactor 43 Wire clip
21 Middle partition 44 Right column
22 Throttle parts 45 Right side panel
23 Reservoir 46 Right rear side panel

Installation
1. Installation Preparation
1.1 Install The Required Tools (Self-Provided)

Number Tool Number Tool

1 Level 10 Saw
2 Electric Hammer 11 Flat Blade Screwdriver
3 Adjustable Wrench 12 Cross Screwdriver
4 Needle-nose Plier 13 Copper Tube Knife
5 Impulse Drill 14 PP-R Tube Knife
6 Ruler 15 PP-R Tube Heat Melting Device
7 Torque Wrench 16 Compound Gauge
8 Hexagonal Wrench 17 Vacuum Pump
9 Hammer 18 Electronic Balance

1.2 Connecting Wires, Insulation Materials, PP-R Pipe, And Connector

a) The material and thickness of the insulation pipe meet the specified requirements. Otherwise,
heat loss and condensation will be caused.
b) Please refer to this manual's “Electrical Installation” description section for wire size selection.

Model The water inlet/outlet size

BLN-006TC1 DN25 (1’’)
BLN-012TC1 DN25 (1’’)

23
 BLN-012TC3 DN25 (1’’)
BLN-018TC1 DN40 (1.5’’)
BLN-018TC3 DN40 (1.5’’)

1.3 Other Installation Materials

a) Fix the pipe bracket and pipe clamp of the connecting pipe
b) Wire threading pipe and pipe clamp
c) Insulting tape, raw tape
d) Expansion bolt
e) Mounting bracket

2. Heat Pump Installation

2.1 The machine installation space meets the following schematic requirements to ensure
regular air circulation and maintenance;
2.2 The location of the machine should be kept away from heat, steam, or flammable gases;

2.3 Do not install the machine in places with strong wind or dust;
2.4 Do not install the machine where it is often passed through the air suction side and air
exhaust side;
2.5 The installation position of the machine should be adequately drained to the nearby sewer.

Heat Pump Installation Space Diagram

24
 Note

Installation In The Following Locations May Cause The Machine To Malfunction:

1. A place with more oil;
2. Wet place
3. Seaside saline-alkali area;
4. Special environmental conditions;
5. High-frequency facilities such as wireless equipment, welding machines, and medical equipment.

3. Outdoor Unit Specific Installation Steps

3.1 Install the unit on a solid surface such as concrete, and the load-bearing cover or mounting
bracket must meet the strength requirements;
3.2 Fasten the outdoor unit to the mounting bracket with bolts and nuts and keep it level;

3.3 If installed on a wall or a roof, the bracket must be firmly fixed to prevent damage caused by
an earthquake or strong wind;

3.4 The positioning dimension of the outdoor unit installation base is 810*394mm. It is required
to install four-position foot bolts with a diameter of 10mm—at the bottom of the installation
of the outdoor unit. The inch recommendation is 1200*450mm.

Installation Precautions
1. The unit should be installed so that the inclination of any vertical surface does not exceed 5
degrees;
2. Do not install the outdoor unit directly on the ground;
3. The strength of the ordinary air-conditioning bracket may not apply to the unit. Please design or
select the frame according to the weight of the team;
4. If the mainframe is installed and fixed on the open balcony and the roof, it is necessary to lift the
unit. Pay attention to the following points when lifting:
4.1 Please use four or more soft slings to lift the handling unit;
4.2 Tor, to avoid scratching and deformation of the surface of the unit, please install the guard
plate on the surface of the team during lifting and loading;
4.3 Before final installation, it is necessary to check whether the foundation is correct or not, in
case it is wrong with the actual object.

4. User Water System Installation

4.1 The Installation Of The Water System Must Meet The Following Principles:
4.1.1 Pipe length is as short as possible;
4.1.2 Pipe diameter must meet the requirements of the unit;
4.1.3 The elbows on the waterway are as few as possible, and the elbow radius is as large
as possible;
4.1.4 The thickness of the water pipe insulation layer meets the specified requirements;

25
 4.1.5 Dust and debris should not enter the pipeline system as much as possible;
4.1.6 The unit must be fixed before the piping system can be installed.

Remarks:
1. Hydraulic calculation must be carried out after the primary water pipe selection is completed. If
the waterside pipeline resistance is more excellent than the selected pump lift, the larger water
pump must be re-selected, or the water pipe must be increased in size;
2. When multiple units are connected in parallel, the primary and circulating water pumps must be
selected as appropriate according to the hydraulic calculation requirements.

Remarks:
1. The same piping design is allowed to distribute the water evenly.
2. The system must be equipped with an automatic water supply valve, and the highest point of the
water system must be equipped with an automatic pressure relief valve;
3. The drain valve shall be installed at the bottom of the pipeline to facilitate drainage;
4. The pressure relief valve is installed at the highest point of the system pipeline, and the terminal
of the water pipe must have an expansion diameter;
5. Normal working water capacity can ensure normal defrosting in winter (ensure that the water
capacity per kW exceeds 10L);
6. The machine has been equipped with a water flow switch; users do not need to install one more;
7. To facilitate the maintenance of the machine, a pressure gauge is required to be installed for the
outlet pipe of the device;
8. If the compartment controls the floor heating, and the number of the manifolds in the smallest
area is less than or equal to 2, please install the differential pressure bypass valve according to the
schematic diagram;

4.2 Water Quality Requirements By The Machine

4.2.1 When water quality is not good, it will produce some scale and sediment such as sand.
Therefore, the water used must be filtered and softened with soft water equipment before
it flows into the heat pump water system;
4.2.2 Please analyze the water quality before using the machine, such as PH value, conductivity,
chloride ion concentration, sulfur ion concentration, etc.

PH Water Hardness Conductivity S Cl Nh4

7~8.5 <50ppm <200vV/cm(25℃) N/A <500ppm N/A
So4 Si Iron content Na Ca<
<50ppm <30ppm <0.3ppm N/A <50ppm

4.3 Water Pipeline Installation Instructions

4.3.1 Install all water pipelines;
4.3.2 Check if any water leaks in the pressurized pipelines;
4.3.3 Clean the water pipelines.
4.4 Water Pipeline Feed-Water And Pipeline Emptying Steps:
4.4.1 Open the pressure relief valve on the water distributor and all valves;

26
 4.4.2 Feed the water at the pipe filling port;
4.4.3 During the feed-water process, it is necessary to observe if the pressure relief valve or the
drain valve has water overflow, and if there is water overflow, it means that the water in
the system has been filled;
4.4.4 Close the pressure relief valve, and then look at the water pressure gauge. If the pressure
value is more than 0.15Mpa, please close the feed-water valve and complete the water
drain.

5. Selection and Installation of Water System Accessories

5.1 Selection Of Circulating Pump
5.1.1 The machine must be installed with a circulating pump to be used. The heat pump provides
the power port of the circulating pump (single-phase power supply). Please refer to the
circuit diagram for wiring. The maximum power of the circulating pump is not allowed to
exceed 1.5 kW.
5.1.2 Please select the circulating pump according to the actual lift required, and the flow must
be guaranteed to meet the requirements of the machine nameplate.
5.2 Selection Of Auxiliary Electric Heater
5.2.1 The user can select the auxiliary electric heater if needed; however, the machine only
provides the port connected with a signal wire to control the auxiliary electric heater.
5.2.2 Professionals must install the installation of an auxiliary electric heater.
5.3 Selection Of Water Flow Switch: The machine has a built-in flow switch, so it does not require
one more water flow switch.
5.4 Other Optional Accessories Recommended

Accessories Description Remark

Buffer Tank 60L or bigger
Expansion Tank 5L Only Pressurized System
Pressure Gauge 1.5 Mpa
Safety Valve 0.3 Mpa Only Pressurized System

6. Electrical Installation
All wiring and grounding must comply with local electrical codes.

Note

1. The specification label should be carefully checked to ensure that the wiring meets the specified
requirements and is correctly wired according to the wiring diagram;
2. The auxiliary electric heater must be equipped with an independent current circuit breaker and
leakage protector;
3. The power supply must meet the requirements of the machine and must be reliably and
effectively wired;
4. Wires should not be in contact with copper pipes, compressors, motors, or other operating

27
 components;
5. Do not change the internal wiring of the machine without permission. Otherwise, the seller will
not commit any responsibility;
6. Do not change the internal wiring of the machine without permission. Otherwise, the seller will
not commit any responsibility;
7. Do not send power before the wiring is completed to avoid personal injury;
8. The supply voltage should vary within ±10% of the standard value.
9. Electrical specifications:

BLN-006 BLN-012 BLN-018

c
TC1 TC1 TC1
Power Supply 220~240 V/ 1/ 50 Hz
Max Input Current (A) 12 17 35.50
Fuse Rated Current(A) 12 17 36
Air Switch (mA) 25 25 50
Power Cable (mm²) 4.00 4.00 6.00

BLN-012 BLN-018
c
TC3 TC3
Power Supply 220~240 V/ 1/ 50 Hz
Max Input Current (A) 10.5 13.2
Fuse Rated Current(A) 17 17
Air Switch (mA) 25 25
Power Cable (mm²) 4.00 4.00

Power Cable And Signal Wire Connection Instruction

1. Remove the machine’s front cover and connect the wire to the corresponding terminal block
according to the electrical wiring diagram to confirm that the connection is secure.
2. Secure the cable with the wire clamp and install the service plate.
3. Do not connect the wrong line. Otherwise, it will cause electrical failure or even damage the
machine.
4. The type and rating of the fuse are based on the specifications of the corresponding controller or
fuse cover.
5. The power cable must be selected and installed by a professional installer. When the installer
chooses the power cable, the power cable should not be lighter than the neoprene armoured cord
(line 57 of IEC 60245). For specific power cable specifications, see the electrical specifications.
6. If the user’s power distribution capacity is insufficient or the power cord (copper core wire) is not
configured as required, the machine cannot be started or operated normally. The seller will not
take any responsibility.

28
 Motherboard Output Definitions

Seq. Port Description Seq. Port Description

1 D01 Hot Water Electric Heating 35 A13 Low-Pressure Sensors
2 D02 Four-Way Valve 36 T1 Outer Coil Temperature
3 D03 Liquid Injection Valve 37 T2 Return Air Temperature
4 D04 Reservation 38 T3 Exhaust Temperature
5 D05 Reservation 39 T4 Cooling Coil Temperature
6 D06 Return Water Valve 40 T5 Economizer Inlet Temperature
7 D07 Crankshaft Heating 41 T6 Economizer Outlet Temperature
8 D08 Chassis Heating 42 T7 Outdoor Ambient Temperature
9 D09 Heating Electric Heating 43 T8 Water Inlet Temperature
10 D010 Hot Water Valve Off 44 T9 Reservation
11 D011 Hot Water Valve On 45 T10 Reservation
12 D012 Air-Conditioning Valve Open 46 T11 Reservation
13 D013 Air-Conditioning Valve Off 47 T12 Reservation
14 D014 Enthalpy Valve 48 T13 Return Water Temperature
15 D015 Low Wind (AC) 49 T14 Freeze Protection Temperature
16 D016 High Wind (AC) 50 T15 Water Discharge Temperature
Water Tank Temperature (Hot
17 D017 Circulating Water Pump 51 T16
Water)
18 C2 Public Side1 52 COM3 Drive Module
19 C1 Public Side2 53 COM4 LCD In-Line Controller
20 D18 Medium Voltage Switch 1 54 COM3 Reservation
21 D17 Reservation 55 COM2 Uplink Monitoring And Control

29
22 D16 Linkage Switch 56 COM1 Module Cascade
23 D15 Reservation 57 ECL Extension Modules
24 D14 Reservation 58 12V DC 12V Power Supply
25 D13 Water Flow Switch 59 EXV1 EEV Main Valve
26 D12 Low Voltage Switch 60 EXV2 Auxiliary Valves
27 D11 High Voltage Switch 61 EXV3 Reservation
28 C3 Water Level Public End 62 EXV4 Reservation
29 H High Water Level (Hot Water) 63 N Power Input Zero Line
Medium Water Level (Hot
30 M 64 C Power Input T-Phase
Water)
31 L Low Water Level (Hot Water) 65 B Power Input S-Phase
32 A12 Reservation 66 A Power Input R-Phase
33 A11 Reservation 67 LED1 8-Bit Dialing Code
34 A14 High-Pressure Sensors

Expansion Board Output Definition

30
Seq Port Description Seq Port Description
1 OUT1 Circulating Water Pump 18 D16 Forced Hot-Water Switch
2 OUT2 Hot Water Electric Heating 19 D15 Gnd
3 OUT3 Air-Conditioning Valve Off 20 D14 Linkage Switch
4 OUT4 Air-Conditioning Valve On 21 D13 Gnd
5 OUT5 Hot Water Valve On 22 D12 Water Flow Switch
6 OUT6 Hot Water Valve Off 23 D11 Gnd
7 OUT7 Reservation 24 TH1 Water Inlet Temperature
8 D08 Chassis Heating 25 TH2 Water Outlet Temperature
9 D09 Electric Heating For Heating 26 TH3 Water Tank Temperature
10 D010 Hot Water Valve Off 27 TH4 Cooling Coil Temperature
11 D011 Hot Water Valve On 28 TH5 Freeze Protection Temperature
12 D012 Air-Conditioning Valve On 29 COM8 Water Flow Meter
13 D013 Air-Conditioning Valve Off 30 ECL Serial Communication
14 D110 Forced Cooling Switch 31 COM2 Rs485
15 D19 Gnd 32 COM2 Rs485
16 D18 Forced Heating Switch 33 COM1 Rs485
17 D17 Gnd 34 AC-L Firewire Input

31
Wire Diagram

32
33
 Commissioning and Maintenance

1. Precautions Before Commissioning

1.1 Is the machine adequately installed?
1.2 Is the wiring and pipe correct?
1.3 Whether the water pipelines are empty or not?
1.4 Whether the heat insulation has been perfected?
1.5 Is the ground wire connected reliably?
1.6 Whether the power supply voltage matches the rated voltage of the machine?
1.7 Is there any obstacle in the air inlet and outlet of the machine?
1.8 Is the safety valve installed correctly?
1.9 Whether the leakage protector can operate effectively?
1.10 The system water pressure is not less than 0.15 MPa, and the maximum pressure cannot
exceed 0.5 MPa;
1.11 In winter, the machine needs to be energized at least 24 hours before the operation, as the
compressor needs to be preheated.

2. Commissioning
Use the controller to control the machine and check the following items according to the
instruction manual: (If there is any fault, please find out the faults and reasons described in the
manual and eliminate them)
2.1 Is the controller regular?
2.2 Is the function key of the controller regular?
2.3 Is the drainage normal?
2.4 Test whether the heating mode and cooling mode are working correctly;
2.5 Is the outlet water temperature average?
2.6 Whether there is vibration and abnormal sound during operation?
2.7 Does the generated wind, noise, and condensate affect neighbours?
2.8 Is there a refrigerant leakage?

3. Operation and Debugging

3.1 About 3mins of protection
Due to the self-protection of the compressor, the machine cannot be restarted again within
3 mins.
3.2 Feature of heating operation
If the ambient temperature is too high during operation, the outdoor motor may run low or
stop.
3.3 In the case of heating operation, when the unit has frost formation, the defrosting procedure
(about 2-8 minutes) is automatically performed to improve the heating effect. The outdoor
motor stops running during the “defrost” operation.

34
 3.4 Power Outage
If there is a power outage during operation, the machine will stop running. Before the power
outage, the controller automatically memories the ON/OFF status of the device. After re-
powering, the controller will send an ON/OFF signal to the device according to the state of
memory before the power outage to ensure that the device recovers from the previous status
from abnormal power failure.

3.5 Heating Capacity

Because the heat pump absorbs heat from the outside, the heating capacity will be reduced
once the outdoor temperature is lowered.
3.6 Electric Leakage Protector
After the unit has been running for some time (usually one month), the leakage protector
needs to press the test button under the closed energized state to check whether the
performance of the leakage protector is regular and reliable (the leakage protector should be
disconnected once every time the test button is pressed). If the accident is not found, the test
can be sent once. If it is not working, the cause should be found, and if necessary, the action
characteristic test should be carried out. After checking, it is confirmed that the leakage
protector itself has failed. It should be replaced or repaired in time.
3.7 Working Temperature Range
To use the machine correctly, please operate under the following conditions, outdoor
temperature: - 30 ℃ ~ 45 ℃ for heating mode, 16 ℃ ~ 45 ℃ for cooling mode.
3.8 Antifreeze in the winter
When the ambient temperature is below 0 ℃, it is strictly forbidden to cut off the power. If
there is an unexpected power failure under this condition, please drain the water from the
heat.

4. Maintenance
1. Please check whether the grounding wire is connected reliably before use. If there is any
abnormality, please replace it in time.
2. Please check the air inlet and outlet of the outdoor unit regularly for blockage.
3. Professionals must clean the outdoor unit heat exchanger, casing, and water circulation piping. It
is recommended to clean the filter of the waterside filter regularly (cleaning is usually done once
a year, depending on the actual situation).
4. Regularly check that the safety valve is working correctly, and ensure that the drain can be drained
normally by manually turning the red knob (usually once every three months, depending on the
actual situation).
5. Regularly (usually once a year, but depending on the actual situation) check whether the water
pipe joint and the refrigerant connection pipe are leaking or leaking refrigerant (there are oil
leakage marks). If there is any leak, please contact the seller.
6. The machine can only be serviced by a professional. The device must be cut off before contacting
the wiring part.
7. Once the machine will not be used for a long time, please cut off the power, drain the water in the
pipeline, and close each valve.

35
 Trouble Analysis

Error code Fault Description Failure Causes

E01 Wrong-Phase Protection Power supply phase sequence error
E02 Power Supply Lack Of Phase The power supply is out of phase
1. Circulating pump failed, or water
system blocked
2. Water flow switch failed, or
opposite installed direction
E03 Outside Water Flow Switch Fault
3. The lift of the circulating pump is
not enough
4. Circulating pump has opposite
installed direction
E04 Abnormal Communication Between The
Main Control Board And Remote Check the communication connection
Module
1. High-voltage switch failed
2. Excessive refrigerant
3. Fan doesn’t work typically, or water
circulated abnormally
E05 High-Pressure Switch One Fault
4. Air or other objects mixed into the
refrigeration system
5. Too much scale in the water heat
exchanger
1. Low-voltage switch fault
2. Lack of refrigerant
E06 Low-Pressure Switch One Fault
3. Fan doesn’t work normally
4. Block exists in refrigeration system
E07 High-Pressure Switch Two Fault Same as E05
E08 Low-Pressure Switch Two Fault Same as E06
E10 Indoor Side Water Flow Failure Same as E03
E11 Limited Time Protection Enter the power-on password
Exhaust Gas Temperature One Too High Lack of refrigerant in the fluorine
E12
Fault circuit system or sensor damage
Exhaust Gas Temperature Two Too High Lack of refrigerant in the fluorine
E13
Fault circuit system or sensor damage
E14 Hot Water Tank Temperature Failure Damaged motherboard or sensor
E15 Water Inlet Temperature Sensor Failure Damaged motherboard or sensor
E16 Coil Sensor One Failure Damaged motherboard or sensor
E17 Coil Sensor Two Failure Damaged motherboard or sensor
E18 Exhaust Gas Sensor One Fault Damaged motherboard or sensor
E19 Exhaust Gas Sensor Two Fault Damaged motherboard or sensor
E20 Indoor Temperature Sensor Failure Damaged motherboard or sensor
E21 Environmental Sensor Failure Damaged motherboard or sensor
E22 User Return Water Sensor Failure Damaged motherboard or sensor
E23 Cooling Subcooling Protection Normal anti-freeze protection

36
E24 Board Change Out Temperature Fault Damaged motherboard or sensor
Damage to the mainboard or water
E25 Water Level Switch Malfunction
level sensor
E26 Anti-Freeze Sensor Malfunction Damaged motherboard or sensor
E27 Water Outlet Sensor Failure Damaged motherboard or sensor
E28 Reservation Reservation
Damage to the mainboard or water
E29 Return Air Sensor One Fault
level sensor
Damage to the mainboard or water
E30 Return Air Sensor Two Fault
level sensor
E31 Water Pressure Switch Failure Water pressure switch failure
Excessive Water Temperature Insufficient water flow or a damaged
E32
Protection sensor
E33 High Pressure One Sensor Fault Damaged motherboard or sensor
E34 Low Pressure One Sensor Fault Damaged motherboard or sensor
E35 Reservation Reservation
E36 Reservation Reservation
The Excessive Temperature Difference
E37 Between Inlet And Outlet Water Insufficient water flow
Protection
E38 DC Fan One Failure Fan drive board or motor damage
E39 DC Fan Two Failure Fan drive board or motor damage
E40 DC Fan Three Failure Fan drive board or motor damage
E41 DC Fan Four Failure Fan drive board or motor damage
E42 Cooling Coil Sensor One Fault Damaged motherboard or sensor
E43 Cooling Coil Sensor Two Fault Damaged motherboard or sensor
E44 Low Ambient Temperature Protection It is a standard protection
E45 High Pressure Two Sensor Failure Damaged motherboard or sensor
E46 Low Pressure Two Sensor Failure Damaged motherboard or sensor
E47 Economizer Inlet Sensor One Failure Damaged motherboard or sensor
E48 Economizer Inlet Sensor Two Failure Damaged motherboard or sensor
E49 Economizer Outlet Sensor One Failure Damaged motherboard or sensor
E50 Economizer Outlet Sensor Two Failure Damaged motherboard or sensor
High Pressure One Overvoltage
E51 Same as E05
Protection
Low-Pressure One Undervoltage
E52 Same as E06
Protection
High-Pressure Two Overvoltage
E53 Same as E05
Protection
High Pressure Two Undervoltage
E54 Same as E06
Protection
Expansion Board Communication
E55 Poor or broken signal cable contact
Exception
Single-phase power unit detects a
E80 Power Supply Error
three-phase electrical signal.
Compressor or compressor driver
E88 Inverter Module 1 Protection
board damaged
Compressor or compressor driver
E89 Inverter Module 2 Protection
board damaged

37
 Damaged DC pump or poor signal
E94 Water Pump Feedback Failure
line contact
Abnormal Communication between
E96 Compressor One Driver and Main Poor or broken signal cable contact
Control Board
Abnormal Communication between
E97 Compressor Two Driver and Main Poor or broken signal cable contact
Control Board
Abnormal Communication between Fan
E98 Motor One Driver and Main Control Poor or broken signal cable contact
Board
Abnormal Communication between Fan
E99 Motor Two Driver and Main Control Poor or broken signal cable contact
Board

Fault Protection Instructions

1. The machine stops running when a fault is detected;
2. When the fault is removed, the compressor is shut down for three minutes before the machine
can be put back into operation;
3. If there are three consecutive low-pressure faults, high-pressure fault, over the current spot, and
gas exhaust temperature too high within 30 minutes, the machine will immediately stop running.
After the fault is rectified, turn the power on again, start the controller, and the device can be put
into operation.
4. If the machine stops running due to the inlet water temperature sensor or the coil temperature
sensor fault due to compressor protection, the device will have to be back into operation 3mins
later after the spot is removed. If the ambient temperature sensor fails, the machine continues to
run.

Maintenance Instructions
1. The machine is equipped with an inspection needle valve on the suction and exhaust pipes. The
maintenance personnel can connect the pressure gauge to check the high and low-pressure
conditions of the system.
2. If the machine is filled with refrigerant under operating conditions, the refrigerant must be served
at the needle valve of the low-pressure side. Suppose the refrigerant is added to the suction side.
In that case, the refrigerant opening must be small so that the refrigerant in the refrigerant bottle
slowly enters the system to prevent liquid slamming.
3. Refrigerant leakage detection
Check if there is any leakage at the joints with soapy water or a refrigerant leak detector. When a
refrigerant leak occurs, the leak point must be found, and the leak point must be repaired. Please
ensure no refrigerant or other pressures are left in the system when improving the leak point.
Otherwise, it will easily cause copper pipe explosive during welding. The tube is blasted by
refrigerant pressure or additional pressure, causing accidental injury to the operator.
Note: When refrigerant leakage occurs in a small space, open all vents or forced ventilation to
discharge the refrigerant before performing related operations to prevent people from suffocating
accidents.

38
 Specification
Model BLN-006TC1 BLN-012TC1 BLN-018TC1 BLN-012TC3 BLN-018TC3
Rated voltage / Frequency 220-240V~ / 50(60)Hz 380-415V/3N~/50(60)Hz
Capacity kW 2.92-9.10 4.30-15.20 7.24-21.90 4.30-15.20 7.24-21.90
Input Power kW 0.61-2.11 0.87-3.73 1.50-5.88 0.87-3.73 1.50-5.88
Heating¹
Input Current A 2.80-9.25 4.02-16.38 6.86-30.25 1.78-6.04 2.82-9.16
COP W/W 4.31-5.66 4.07-5.57 3.82-5.59 4.07-5.57 3.82-5.59
Capacity kW 2.99-8.16 4.25-14.55 6.36-19.45 4.25-14.55 6.36-19.45
Input Power kW 1.03-2.92 1.45-4.28 2.15-6.85 1.45-4.28 2.15-6.85
Heating²
Input Current A 4.57-12.79 6.71-18.80 9.84-30.12 2.84-6.78 3.71-10.60
COP W/W 2.79-3.46 2.83-3.45 2.84-3.57 2.83-3.45 2.84-3.57
Capacity kW 1.38-5.70 3.65-11.04 4.55-17.20 3.65-11.04 4.55-17.20
Cooling Input Power kW 0.67-2.44 1.12-3.97 1.85-7.31 1.12-3.97 1.85-7.31
Input Current A 3.06-10.27 5.18-17.44 8.47-32.1 1.97-6.30 2.99-11.26
SCOP (Water Temp. At 35℃) 4.83 4.77 4.81 4.74 4.79
SCOP (Water Temp. At 55℃) 3.71 3.77 3.72 3.70 3.71
Rated Input Power kW 3.5 5.40 7.50 5.85 10.5
Rated Input Current A 15.0 25.0 35.0 10.0 17.0
Refrigerant Type/Charge/GWP .../kg R290/0.55/3 R290/1.05/3 R290/1.4/3 R290/1.05/3 R290/1.4/3
CO Equivalent
2 / 0.0017t 0.0032t 0.0042t 0.0032t 0.0042t
Operation Pressure(Low Side) MPa 0.8 0.8 0.8 0.8 0.8
Operation Pressure(High Side) MPa 3.0 3.0 3.0 3.0 3.0
Maximum Allowable Pressure MPa 3.2 3.2 3.2 3.2 3.2
Electrical Shockproof / I I I I I
IP Class / IPX4 IPX4 IPX4 IPX4 IPX4
Max. Outlet Water Temp. ℃ 75 75 75 75 75
Operating Ambient Temperature ℃ -25~45 -25~45 -25~45 -25~45 -25~45
Water Piping Connections inch G1 G1 G1-1/4 G1 G1-1/4
Rated Water Flow m³/h 1.0 2.06 3.10 2.06 3.1
Water Pressure Drop kPa 20 20 55 20 55
Min/Max Water Pressure MPa 0.1/0.3 0.1/0.3 0.1/0.3 0.1/0.3 0.1/0.3
Sound pressure Level dB(A) 46 53 56 54 56
Net Dimensions ( L×W×H ) mm 1187×418×805 1287×448×904 1187×488×1456 1287×448×904 1187×488×1456
Net Weight kg 110 134 195 134 195
Rated Test Conditions:
Heating¹: Ambient Temp 7℃/6℃(DB/WB),Water-In/Out Temp 30℃/35℃ Heating²: Ambient Temp 7℃/6℃(DB/WB),Water-In/Out Temp 47℃/55℃ Cooling: Ambient Temp 35℃/24℃(DB/WB),Water-In/Out Temp 12℃/7℃

Note : We reserves the right to discontinue, or change at any time, specifications or designs
without notices and without incurring obligations

39
 After-sale Service
Relevant state regulations carry out the after-sales service of our products. Within the scope of the
warranty period, If the machine is not working correctly under reasonable use, please contact the seller.
The user must designate a person to manage and use the unit reasonably and correctly by our company’s
“Instructions for Use.” Accidents caused by improper use are not covered by our company’s warranty,
and the repair costs and repair costs beyond the warranty period must be taken care of by the user.

1. After-sale Service
The seller or the specified professional installer should perform maintenance and repair. Improper
maintenance or repair may result in water leakage, electric shock, and fire.
1.1 Please contact the seller when the machine has to be moved or reinstalled. Improper installation
may result in water leakage, electric shock, and fire.
1.2 When you need after-sales service, please contact the seller and provide the following details:
1) Model No.
2) Serial Number and Manufacture Date
3) Detailed Description of the fault
4) Your name, Address, and Contact Number
If the warranty period is expired or the malfunction is caused by improper use, the company will
charge a certain service fee if you need after-sales service.

2. Maintenance
After a period of use, the heat pump’s performance will be reduced due to the accumulation of
dust inside the machine, so maintenance is required.
1) You should regularly check the water supply system to avoid the air entering the water system
and the occurrence of low water flow, which would reduce the performance and reliability of
the heat pump.
2) Clean your filtration system regularly to avoid unit damage because of a dirty or clogged filter.
3) Discharge the water from the bottom of the water pump if the heat pump will stop running
for a long time (especially in winter)
4) At any other moment, check the water flow to confirm enough water before the unit starts
to run again.
5) After the unit is conditioned in winter, it is preferred to cover the team with a unique winter
heat pump cover.

40
 Appendix for Controller

Icon Status Functions or meanings Remark

Lights out Currently in off or non-hot water mode Display on/off status

Constant flashing Currently in hot water mode on Display on/off status

Lights out Currently in off or non-heating mode Display on/off status

Constant flashing Currently in heating mode Display on/off status

Lights out Currently in off or non-cooling mode Display on/off status

Constant flashing Currently in cooling mode Display on/off status

Lights out Currently in off or non-floor heating mode Display on/off status

Constant flashing Currently in floor heating mode Display on/off status

Constant flashing Silent mode / Night mode Power on display

Constant flashing Powerful mode Power on display

Constant flashing Intelligent Mode Power on display

Constant flashing Electric auxiliary heating work (AC, hot water electric heating) Power on display

1s flashing Electric auxiliary heat quick heat mode is enabled Power on display

2s flashing Electric auxiliary heat sterilization mode is enabled Power on display

Flashing WIFI Allocation

Constant flashing WIFI connection successful

Constant flashing Represents water intake

Constant flashing Represents water discharge

Constant flashing Represents actual temperature/room temperature

Constant flashing Representative Settings

Constant flashing Display Celsius temperature

Constant flashing Display Fahrenheit temperature

Constant flashing Show percentage

88.8 Constant flashing Display of actual values, set values and fault codes

Flashing Circulating water pump: freeze-proof operation

Constant flashing Circulating water pump: normal operation

41
 Constant flashing Hydration valve open

Constant flashing Return water valve open

c 1Hz flashing Activate timed water return feature

2Hz flashing Activate manual water return function

Constant flashing High, medium and low water levels are displayed

Constant flashing The water supply valve

Constant flashing Photovoltaic mode/solar heating

1 Hz flashing Start PV timing

Flashing Currently in shutdown and refrigerant recovery state

Constant flashing Currently on and defrosting

Constant flashing Enter maintenance status

Constant flashing Alarm is currently occurring

Constant flashing Current button is locked

Constant flashing Compressor operation

Constant flashing High wind operation of the fan

Constant flashing Fan low wind operation

1 second flash Ventilation mode: high speed wind

2 second flash Ventilation mode: low speed wind

Constant flashing Online networking

Constant flashing Display the current network unit number

88.8 Display Display real-time time

Always bright Enable timed work mode

Display Currently in the power-on timer period

Flashing Current set working period start time

Display Currently in power-on timed non-working hours

Flashing Current set working period end time

Timed working hours 1, 2, 3, always on when set or when the

Flashing / Light out
clock enters this period, off in the rest of the case

Display Show current week 1, 2, 3, 4, 5, 6, 7

42