INTERNATIONAL ISO
STANDARD 3547-1
Third edition
2018-07
Plain bearings — Wrapped bushes —
Part 1:
Dimensions
Paliers lisses — Bagues roulées —
Partie 1: Dimensions
iTeh STANDARD PREVIEW
(standards.iteh.ai)
ISO 3547-1:2018
https://standards.iteh.ai/catalog/standards/sist/98a14851-325e-4cbb-8a0a-
bad5aa9cb6f5/iso-3547-1-2018
Reference number
ISO 3547-1:2018(E)
© ISO 2018
ISO 3547-1:2018(E)
iTeh STANDARD PREVIEW
(standards.iteh.ai)
ISO 3547-1:2018
https://standards.iteh.ai/catalog/standards/sist/98a14851-325e-4cbb-8a0a-
bad5aa9cb6f5/iso-3547-1-2018
COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email:
[email protected] Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
ISO 3547-1:2018(E)
Contents Page
Foreword......................................................................................................................................................................................................................................... iv
1 Scope.................................................................................................................................................................................................................................. 1
2 Normative references....................................................................................................................................................................................... 1
3 Terms and definitions...................................................................................................................................................................................... 1
4 Symbols and units................................................................................................................................................................................................ 1
5 Dimensions.................................................................................................................................................................................................................. 2
6 Design............................................................................................................................................................................................................................... 9
7 Example for calculation of inside diameter, Di ...................................................................................................................10
8 Designation..............................................................................................................................................................................................................10
Bibliography.............................................................................................................................................................................................................................. 11
iTeh STANDARD PREVIEW
(standards.iteh.ai)
ISO 3547-1:2018
https://standards.iteh.ai/catalog/standards/sist/98a14851-325e-4cbb-8a0a-
bad5aa9cb6f5/iso-3547-1-2018
© ISO 2018 – All rights reserved iii
ISO 3547-1:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
iTeh STANDARD PREVIEW
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www.iso.org/iso/foreword.html.
(standards.iteh.ai)
This document was prepared by Technical Committee ISO/TC 123, Plain bearings, Subcommittee SC 3,
Dimensions, tolerances and construction details. ISO 3547-1:2018
https://standards.iteh.ai/catalog/standards/sist/98a14851-325e-4cbb-8a0a-
This third edition cancels and replaces the second edition (ISO 3547-1:2006), which has been technically
bad5aa9cb6f5/iso-3547-1-2018
revised. The main changes compared to the previous edition are as follows:
— Normative references have been updated.
— Formulae for the minimum and maximum inside diameters of the bush have been added.
— A formula for the expansion of the housing bore due to the pressing in of the bush has been added.
A list of all parts in the ISO 3547 series can be found on the ISO website.
iv © ISO 2018 – All rights reserved
INTERNATIONAL STANDARD ISO 3547-1:2018(E)
Plain bearings — Wrapped bushes —
Part 1:
Dimensions
1 Scope
This document specifies the dimensions and designations of cylindrical and flanged wrapped bushes
made of mono and multi-layer bearing material for plain bearing applications.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 4378-1, Plain bearings — Terms, definitions, classification and symbols — Part 1: Design, bearing
materials and their properties
iTeh STANDARD PREVIEW
ISO 4378-4, Plain bearings — Terms, definitions, classification and symbols — Part 4: Basic symbols
(standards.iteh.ai)
ISO 12301, Plain bearings — Quality control techniques and inspection of geometrical and material quality
characteristics
ISO 3547-1:2018
https://standards.iteh.ai/catalog/standards/sist/98a14851-325e-4cbb-8a0a-
3 Terms and definitions bad5aa9cb6f5/iso-3547-1-2018
For the purposes of this document, the terms and definitions given in ISO 4378-1 and ISO 4378-4 apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp
— IEC Electropedia: available at http://www.electropedia.org/
4 Symbols and units
See Table 1.
Table 1 — Symbols and units
Symbol Description Unit
B Width of the bush mm
Ci Inside chamfer mm
Co Outside chamfer mm
Di Inside diameter of the bush mm
Di,min Minimum inside diameter of the bush mm
Di,max Maximum inside diameter of the bush mm
Di, ch Inside diameter of the bush in the ring gauge mm
Dfl Flange diameter mm
a For bushes which are made of a single material, s1 = s3 or s2 = s3.
© ISO 2018 – All rights reserved 1
ISO 3547-1:2018(E)
Table 1 (continued)
Symbol Description Unit
DH Housing bore diameter mm
DH,min Minimum housing bore diameter mm
DH,max Maximum housing bore diameter mm
Do Outside diameter of the bush mm
Do,m Mean diameter of the bush mm
DH,m Mean housing bore diameter mm
DS Shaft diameter mm
dch, 1 Diameter of the checking block or ring gauge mm
E Expansion of the housing bore mm
Ra Surface roughness µm
r Flange radius mm
s1 Thickness of the bearing backinga mm
s2 Thickness of the bearing material layera mm
s3 Wall thicknessa mm
s3,min Minimum wall thickness mm
s3,max Maximum wall thickness mm
sfl Flange thickness mm
a iTeh STANDARD PREVIEW
For bushes which are made of a single material, s1 = s3 or s2 = s3.
(standards.iteh.ai)
5 Dimensions
ISO 3547-1:2018
See Figure 1 and Tables 2 to 4.
https://standards.iteh.ai/catalog/standards/sist/98a14851-325e-4cbb-8a0a-
Di ,max = DH ,max − 2 ⋅ s 3 ,min bad5aa9cb6f5/iso-3547-1-2018 (1)
Di ,min = DH ,min − 2 ⋅ s 3 ,max (2)
This assumes that there is no expansion of the bore in the housing caused by pressing in the bush. In
reality, the expansion depends on several factors, such as the stiffness of the housing and the bush. An
example of the calculation is given in Clause 7.
The wall thickness tolerance depends on whether or not there is a machining allowance in the bush
bore and on the material type, as specified in ISO 3547-4. The preferred tolerance series (A to E) is
specified in Table 5.
Instead of the wall thickness, the inside diameter, Di, ch, of the bush may be specified. Di, ch is the inside
diameter of the bush, when this is pressed into a ring gauge (Test C — gauging — in accordance with
ISO 3547-2; see also ISO 3547-6).
For bushes which are supplied with a machined bore (Series W), the tolerances of the inside diameter of
the bush, Di, ch, checked in a ring gauge, are given in Table 6.
In no case shall wall thickness and inside diameter be given at the same time as the dimensions that are
to be checked.
The tolerance for the inside diameter, Di, ch, of the bush in the ring gauge is given in Table 6. The tolerance
of the inside diameter of a bush pressed into a housing is found from the sum of the tolerance for, Di, ch,
and the tolerance of the housing bore. As in the case of the calculation of the inside diameter from the
wall thickness, it is assumed that there is no expansion of the housing bore.
Dimensions for the outside diameter, Do, of the bush are given in Table 7.
2 © ISO 2018 – All rights reserved
ISO 3547-1:2018(E)
a) Type C cylindrical bush
iTeh STANDARD PREVIEW
(standards.iteh.ai)
ISO 3547-1:2018
https://standards.iteh.ai/catalog/standards/sist/98a14851-325e-4cbb-8a0a-
bad5aa9cb6f5/iso-3547-1-2018
b) Type F flanged bush
Key
1 butt joint
a Thickness of the bearing material layer: only valid as a basis for calculation in accordance with ISO 3547-2.
b Ci may be a chamfer or break edge, in accordance with ISO 13715.
c 0,2 mm min. for nominal wall thickness 0,5 mm.
d rmax = s3.
Figure 1 — Cylindrical and flanged bush
© ISO 2018 – All rights reserved 3
ISO 3547-1:2018(E)
Table 2 — Preferred nominal dimensions for inside diameter, Di, outside diameter, Do, wall
thickness, s3, and bush width, B
Dimensions and tolerances in millimetres
s3 = 0,5
Ba
Di Do s3
3 4 5 6 8 10 12
2 3 0,5 a a
3 4 0,5 a a a
4 5 0,5 a a a
5 6 0,5 a a a
6 7 0,5 a a a a
8 9 0,5 a a a a
10 11 0,5 a a a
s3 = 0,75
Ba
Di Do s3
3 4 5 6 7 8 10
2 3,5 0,75 a a
3 4,5 0,75 a a a
4 5,5 0,75 a a a a
iTeh STANDARD PREVIEW s3 = 1,0
B a
Di Do s3
3 4
(standards.iteh.ai)
5 6 7 8 10 12 15 20 25
3 5 1,0 a a a a
ISO 3547-1:2018
4 6 1,0 a a a
https://standards.iteh.ai/catalog/standards/sist/98a14851-325e-4cbb-8a0a-
6 8 1,0 a a a a
bad5aa9cb6f5/iso-3547-1-2018 a
7 9 1,0 a a a a
8 10 1,0 a a a a a a
9 11 1,0 a
10 12 1,0 a a a a a b b
12 14 1,0 a a a a a b b b
13 15 1,0 a b b
14 16 1,0 a a b b b
15 17 1,0 a a b b b
16 18 1,0 a a b b b
17 19 1,0 b b
18 20 1,0 a b b b
4 © ISO 2018 – All rights reserved
ISO 3547-1:2018(E)
Table 2 (continued)
s3 = 1,5
Ba
Di Do s3
8 10 12 15 20 25 30 40
8 11 1,5 b b
10 13 1,5 a a a a
12 15 1,5 b b b
13 16 1,5 b b b b
14 17 1,5 b b b b
15 18 1,5 a a a a a
16 19 1,5 a a a b a
18 21 1,5 a b b
20 23 1,5 a a b b b
22 25 1,5 a b b b
24 27 1,5 a b b b
25 28 1,5 a b b b
28 31 1,5 b b b
s3 = 2
Ba
Di Do s3
iTeh15STANDARD
20 25 PREVIEW
30 40 50 60 70 80
28 32 2,0 a a a b b
30 34 2,0 a
(standards.iteh.ai)
a a b b
32 36 2,0 a ISO 3547-1:2018 b b
35 39 2,0 a b b b
https://standards.iteh.ai/catalog/standards/sist/98a14851-325e-4cbb-8a0a-
37 40 2,0 bad5aa9cb6f5/iso-3547-1-2018
a b b
38 42 2,0 a b b
40 44 2,0 a b b b
s3 = 2,5
Ba
Di Do s3
20 25 30 40 50 60 70 80 100 115
45 50 2,5 a a b b
50 55 2,5 a a a b b b
55 60 2,5 a a b b
60 65 2,5 a a b b c
65 70 2,5 a b c
70 75 2,5 a b c
75 80 2,5 b b c
80 85 2,5 b b c c
85 90 2,5 b b c c
90 95 2,5 b b c
95 100 2,5 b c
100 105 2,5 b b c c
105 110 2,5 b c c
110 115 2,5 b c c
115 120 2,5 b b b c
120 125 2,5 b b c
© ISO 2018 – All rights reserved 5
