Built-in Power Supply Photoelectric Sensor

E3JK <NEW>
Long-distance Photoelectric Sensor
That Supports AC/DC Power Supplies
• Long sensing distance that is approximately 8
times that of our conventional model (for the
Through-beam and Diffuse-reflective models).
(Through-beam: 40 m, Retro-reflective: 7 m, and
Diffuse-reflective: 2.5 m.)
• Improved visibility:
• A red LED that makes the spot visible.
• Large indicators that can be seen even from a
distance.
• Improved operability.
(Enlarged sensitivity adjuster and operation For the most recent information on models that have been certified for
selector) safety standards, refer to your OMRON website.

• Freely selectable power supply input (24 to 240

VDC, 24 to 240 VAC).
(Additional types added to the DC type lineup.)
• Models with infrared LEDs are also available.
Refer to the Safety Precautions on page
15.

Applications

Elevator cage detection Detection of packages jutting out from their storage location

Pallet detection for agricultural produce conveyors Workpiece detection for woodworking machines

1
 E3JK
Ordering Information
Sensors Red light Infrared light
Sensors with Mounting Brackets and Reflectors (The model numbers contain (“-C.”)
A Mounting Bracket (E39-L40) is included. A Reflector (E39-R1) is included with Retro-reflective models.
Output
Power supply
Sensing method Appearance Sensing distance configu- Model
voltage
ration
E3JK-TR11-C 2M
40m Emitter: E3JK-TR11-L 2M
Receiver: E3JK-TR11-D 2M
E3JK-TR12-C 2M
5m Emitter: E3JK-TR12-L 2M
Through-beam *1 Receiver: E3JK-TR12-D 2M
(Emitter + Receiver) E3JK-TR13-C 2M
40 m Emitter: E3JK-TR13-L 2M
Receiver: E3JK-TR13-D 2M
E3JK-TR14-C 2M
5m Emitter: E3JK-TR14-L 2M
Receiver: E3JK-TR14-D 2M

7m *2
[100mm]
(When using E39-R1)
E3JK-RR11-C 2M
11m
[100mm]
(When using E39-R2)
Retro-reflective
without MSR function *2 Relay
AC/DC power 7m
[100 mm]
supply (When using E39-R1)
selectable E3JK-RR13-C 2M
type 11 m
[100 mm]
(When using E39-R2)

*2
6m
[100mm]
Retro-reflective (When using E39-R1)
E3JK-RR12-C 2M
with MSR function
10m
[100mm]
(When using E39-R2)

2.5m E3JK-DR11-C 2M

300mm E3JK-DR12-C 2M
Diffuse-reflective
2.5 m E3JK-DR13-C 2M

300 mm E3JK-DR14-C 2M

*1. Through-beam Sensors are sold in sets that include both the Emitter and Receiver.
*2. Values in parentheses indicate the minimum required distances between the Sensors and Reflectors.

2
 E3JK

Sensors Red light Infrared light

Sensors without Mounting Brackets or Reflectors
A Mounting Bracket and Reflector are not included. Purchase a Mounting Bracket and Reflector separately to match the intended
use of the Sensor.
Output
Power supply
Sensing method Appearance Sensing distance configu- Model
voltage
ration
E3JK-TR11 2M
40 m Emitter: E3JK-TR11-L 2M
Receiver: E3JK-TR11-D 2M
E3JK-TR12 2M
5m Emitter: E3JK-TR12-L 2M
Through-beam *1 Receiver: E3JK-TR12-D 2M
(Emitter + Receiver) E3JK-TR13 2M
40 m Emitter: E3JK-TR13-L 2M
Receiver: E3JK-TR13-D 2M
E3JK-TR14 2M
5m Emitter: E3JK-TR14-L 2M
Receiver: E3JK-TR14-D 2M

*3
7m
[100 mm]
(When using E39-R1)
E3JK-RR11 2M
11 m
[100 mm]
Retro-reflective (When using E39-R2)

without MSR function *3

7m
AC/DC power [100 mm]
supply (When using E39-R1)
Relay
selectable E3JK-RR13 2M
*2
type 11 m
[100 mm]
(When using E39-R2)

*3
6m
[100 mm]
Retro-reflective (When using E39-R1)
E3JK-RR12 2M
with MSR function
10 m
[100 mm]
(When using E39-R2)

2.5 m E3JK-DR11 2M

300 mm E3JK-DR12 2M
Diffuse-reflective

2.5 m E3JK-DR13 2M

300 mm E3JK-DR14 2M

*1. Through-beam Sensors are sold in sets that include both the Emitter and Receiver.
*2. A Reflector is not included. Purchase a Reflector separately to match the intended use of the Sensor.
*3. Values in parentheses indicate the minimum required distances between the Sensors and Reflectors.

3
 E3JK

Red light Infrared light

A Mounting Bracket and Reflector are not included. Purchase a Mounting Bracket and Reflector separately to match the intended
use of the Sensor.
Output
Power supply
Sensing method Appearance Sensing distance configu- Model
voltage
ration
E3JK-TN11 2M
NPN Emitter: E3JK-TN11-L 2M
Receiver: E3JK-TN11-D 2M
40 m
E3JK-TP11 2M
PNP Emitter: E3JK-TP11-L 2M
Receiver: E3JK-TP11-D 2M
E3JK-TN12 2M
NPN Emitter: E3JK-TN12-L 2M
Receiver: E3JK-TN12-D 2M
5m
E3JK-TP12 2M
PNP Emitter: E3JK-TP12-L 2M
Through-beam *1 Receiver: E3JK-TP12-D 2M
(Emitter + Receiver) E3JK-TN13 2M
NPN Emitter: E3JK-TN13-L 2M
Receiver: E3JK-TN13-D 2M
40 m
E3JK-TP13 2M
PNP Emitter: E3JK-TP13-L 2M
Receiver: E3JK-TP13-D 2M
E3JK-TN14 2M
NPN Emitter: E3JK-TN14-L 2M
Receiver: E3JK-TN14-D 2M
5m
E3JK-TP14 2M
PNP Emitter: E3JK-TP14-L 2M
Receiver: E3JK-TP14-D 2M

*3
7m
[100 mm] NPN E3JK-RN11 2M
(When using E39-R1)

11 m
DC [100 mm] PNP E3JK-RP11 2M
(When using E39-R2)
Retro-reflective
without MSR function *3
7m
[100 mm] NPN E3JK-RN13 2M
(When using E39-R1)

*2
11 m
[100 mm] PNP E3JK-RP13 2M
(When using E39-R2)

*3
6m
[100 mm] NPN E3JK-RN12 2M
Retro-reflective (When using E39-R1)

with MSR function

10 m
[100 mm] PNP E3JK-RP12 2M
(When using E39-R2)

NPN E3JK-DN11 2M
2.5 m
PNP E3JK-DP11 2M
NPN E3JK-DN12 2M
300 mm
PNP E3JK-DP12 2M
Diffuse-reflective
NPN E3JK-DN13 2M
2.5 m
PNP E3JK-DP13 2M
NPN E3JK-DN14 2M
300 mm
PNP E3JK-DP14 2M
*1. Through-beam Sensors are sold in sets that include both the Emitter and Receiver.
*2. A Reflector is not included. Purchase a Reflector separately to match the intended use of the Sensor.
*3. Values in parentheses indicate the minimum required distances between the Sensors and Reflectors.

4
 E3JK

Accessories (Order Separately)

Reflectors (A Reflector is required for each Retro-reflective Sensor.) [Refer to Dimensions on page 17.]
The E39-R1 is enclosed with Sensors with model numbers that contain “-C.”
Name Sensing distance (rated value) Model Quantity
E3JK-R@11 7 m [100 mm] *
E3JK-R@12 6 m [100 mm] * E39-R1 1
E3JK-R@13 7 m [100 mm] *
E3JK-R@11 9 m [100 mm] *
Reflectors E3JK-R@12 7 m [100 mm] * E39-R1S 1
E3JK-R@13 9 m [100 mm] *
E3JK-R@11 11 m [100 mm] *
E3JK-R@12 10 m [100 mm] * E39-R2 1
E3JK-R@13 11 m [100 mm] *
Note: Refer to Engineering Data on page 12 for details.
*Values in parentheses indicate the minimum required distances between the Sensors and Reflectors.

Mounting Bracket [Refer to Dimensions on page 17.]

A Mounting Bracket is enclosed with Sensors with model numbers that contain “-C.”
Appearance Model Quantity

E39-L40 1

Note: 1. When using a Through-beam Sensor, order one Mounting Bracket for the Receiver and one for the Emitter.
2. For details, refer to Mounting Brackets on E39-L/E39-S/E39-R which can be accessed from your OMRON website.

5
 E3JK
Ratings and Specifications

Sensing method Through-beam

Item Model E3JK-TR11-@ E3JK-TR12-@ E3JK-TR13-@ E3JK-TR14-@
Sensing distance 40 m 5m 40 m 5m
Standard sensing object Opaque: 17-mm dia. min.
Differential travel −
Directional angle Both Emitter and Receiver 3° min.
Light source (wavelength) Red LED (624 nm) Infrared LED (850 nm)
24 to 240 VDC ±10%,
Power supply voltage ripple (p-p): 10% max.
24 to 240 VAC ±10%, 50/60 Hz
Power DC 3 W max. (Emitter 1.5 W max. Receiver 1.5 W max.)
consumption AC 3 W max. (Emitter 1.5 W max. Receiver 1.5 W max.)
Relay output SPDT, 250 VAC, 3 A max. (cosϕ= 1),
Control output 5 VDC, 10 mA min.,
Light-ON/Dark-ON selectable
Protection circuits −
Life Mechanical 50,000,000 times min. (switching frequency: 18,000 times/h)
expectancy
(relay output) Electrical 100,000 times min. (switching frequency: 1,800 times/h)

Response time 20 ms max.

Sensitivity adjustment One-turn adjuster Receiver (E3JK-TR1@-D) only
Ambient illumination
Incandescent lamp: 3,000 lx max., Sunlight: 11,000 lx max.
(Receiver side)
Ambient temperature range Operating: −25°C to 55°C, Storage: −40°C to 70°C (with no icing or condensation)
Ambient humidity range Operating: 35% to 85%, Storage: 35% to 95% (with no condensation)
Insulation resistance 20 MΩ min. at 500 VDC
Dielectric strength 1,500 VAC, 50/60 Hz for 1 min
Vibration Destruction 10 to 55 Hz with a 1.5 mm double amplitude for 2 hours each in X, Y, and Z directions
resistance Malfunction 10 to 55 Hz with a 1.5 mm double amplitude for 2 hours each in X, Y, and Z directions
Shock Destruction 500 m/s2 for 3 times each in X, Y, and Z directions
resistance Malfunction 100 m/s2 for 3 times each in X, Y, and Z directions
Degree of protection IEC 60529 IP64
Connection method Pre-wired (standard length: 2 m)
Weight (packed state) Approx. 350 g
Case ABS (Acrylonitrile Butadiene Styrene)
Lens/Display
Methacrylic resin
Material window
Adjuster POM
Cable PVC
Bending radius of cable R18
Accessories Instruction manual and Mounting Bracket (E3JK-TR1@-C only)

6
 E3JK

Retro-reflective
Sensing method Retro-reflective (without MSR function)
(with MSR function)
Item Model E3JK-RR11-@ E3JK-RR13-@ E3JK-RR12-@
6 m [100 mm]* (When using
7 m [100 mm]* (When using E39-R1), 11 m [100 mm]*
Sensing distance E39-R1), 10 m [100 mm]* (When
(When using E39-R2)
using E39-R2)
Standard sensing object Opaque: 75-mm dia. min. (When using E39-R1), Opaque: 100-mm dia. min. (When using E39-R2)
Differential travel −
Directional angle 1.5° min.
Light source (wavelength) Red LED (624 nm) Infrared LED (850 nm) Red LED (624 nm)
24 to 240 VDC ±10%,
Power supply voltage ripple (p-p): 10% max.
24 to 240 VAC ±10%, 50/60 Hz
Power DC 2 W max.
consumption AC 2 W max.
Relay output SPDT, 250 VAC, 3 A max. (cosϕ= 1),
Control output 5 VDC, 10 mA min.,
Light-ON/Dark-ON selectable
Protection circuits Mutual interference prevention function
Life Mechanical 50,000,000 times min. (switching frequency: 18,000 times/h)
expectancy
(relay output) Electrical 100,000 times min. (switching frequency: 1,800 times/h)

Response time 20 ms max.

Sensitivity adjustment One-turn adjuster
Ambient illumination
Incandescent lamp: 3,000 lx max., Sunlight: 11,000 lx max.
(Receiver side)
Ambient temperature range Operating: −25°C to 55°C, Storage: −40°C to 70°C (with no icing or condensation)
Ambient humidity range Operating: 35% to 85%, Storage: 35% to 95% (with no condensation)
Insulation resistance 20 MΩ min. at 500 VDC
Dielectric strength 1,500 VAC, 50/60 Hz for 1 min
Vibration Destruction 10 to 55 Hz with a 1.5 mm double amplitude for 2 hours each in X, Y, and Z directions
resistance Malfunction 10 to 55 Hz with a 1.5 mm double amplitude for 2 hours each in X, Y, and Z directions
Shock Destruction 500 m/s2 for 3 times each in X, Y, and Z directions
resistance Malfunction 100 m/s2 for 3 times each in X, Y, and Z directions
Degree of protection IEC 60529 IP64
Connection method Pre-wired (standard length: 2 m)
Weight (packed state) Approx. 180 g
Case ABS (Acrylonitrile Butadiene Styrene)
Lens/Display
Methacrylic resin
Material window
Adjuster POM
Cable PVC
Bending radius of cable R18
Accessories Instruction manual, Mounting Bracket (E3JK-RR1@-C only), and Reflector (E3JK-RR1@-C only)
*Values in parentheses indicate the minimum required distances between the Sensors and Reflectors.

7
 E3JK

Sensing method Diffuse-reflective

Item Model E3JK-DR11-@ E3JK-DR12-@ E3JK-DR13-@ E3JK-DR14-@
White paper White paper White paper White paper
Sensing distance
(300 × 300 mm): 2.5 m (100 × 100 mm): 300 mm (300 × 300 mm): 2.5 m (100 × 100 mm): 300 mm
Standard sensing object −
Differential travel 20% max. of sensing distance
Directional angle −
Light source (wavelength) Red LED (624 nm) Infrared LED (850 nm)
24 to 240 VDC ±10%,
Power supply voltage ripple (p-p): 10% max.
24 to 240 VAC ±10%, 50/60 Hz
Power DC 2 W max.
consumption AC 2 W max.
Relay output SPDT, 250 VAC, 3 A max. (cosϕ= 1),
Control output 5 VDC, 10 mA min.,
Light-ON/Dark-ON selectable
Protection circuits Mutual interference prevention function
Life Mechanical 50,000,000 times min. (switching frequency: 18,000 times/h)
expectancy
(relay output) Electrical 100,000 times min. (switching frequency: 1,800 times/h)

Response time 20 ms max.

Sensitivity adjustment One-turn adjuster
Ambient illumination
Incandescent lamp: 3,000 lx max., Sunlight: 11,000 lx max.
(Receiver side)
Ambient temperature range Operating: −25°C to 55°C, Storage: −40°C to 70°C (with no icing or condensation)
Ambient humidity range Operating: 35% to 85%, Storage: 35% to 95% (with no condensation)
Insulation resistance 20 MΩ min. at 500 VDC
Dielectric strength 1,500 VAC, 50/60 Hz for 1 min
Vibration Destruction 10 to 55 Hz with a 1.5 mm double amplitude for 2 hours each in X, Y, and Z directions
resistance Malfunction 10 to 55 Hz with a 1.5 mm double amplitude for 2 hours each in X, Y, and Z directions
Shock Destruction 500 m/s2 for 3 times each in X, Y, and Z directions
resistance Malfunction 100 m/s2 for 3 times each in X, Y, and Z directions
Degree of protection IEC 60529 IP64
Connection method Pre-wired (standard length: 2 m)
Weight (packed state) Approx. 180 g
Case ABS (Acrylonitrile Butadiene Styrene)
Lens/Display
Methacrylic resin
Material window
Adjuster POM
Cable PVC
Bending radius of cable R18
Accessories Instruction manual and Mounting Bracket (E3JK-DR1@-C only)

8
 E3JK

Sensing method Through-beam

Model NPN output E3JK-TN11 E3JK-TN12 E3JK-TN13 E3JK-TN14
Item PNP output E3JK-TP11 E3JK-TP12 E3JK-TP13 E3JK-TP14
Sensing distance 40 m 5m 40 m 5m
Standard sensing object Opaque: 17-mm dia. min.
Differential travel −
Directional angle Both Emitter and Receiver 3° min.
Light source (wavelength) Red LED (624 nm) Infrared LED (850 nm)
Power supply voltage 10 to 30 VDC, including ripple (p-p): 10%
Power DC 40 mA max. (Emitter 25 mA max. Receiver 15 mA max.)
consumption AC −
Load power supply voltage: 30 V max., Load current: 100 mA max., Residual voltage: 3 V max., open-
Control output
collector output (NPN/PNP output depending on model), Light-ON/Dark-ON selectable
Power supply reverse polarity protection, Output short-circuit protection, and Output reverse polarity
Protection circuits
protection
Life Mechanical −
expectancy
(relay output) Electrical −
Response time 1 ms max.
Sensitivity adjustment One-turn adjuster Receiver (E3JK-T@@@-D) only
Ambient illumination
Incandescent lamp: 3,000 lx max., Sunlight: 11,000 lx max.
(Receiver side)
Ambient temperature range Operating: −25°C to 55°C, Storage: −40°C to 70°C (with no icing or condensation)
Ambient humidity range Operating: 35% to 85%, Storage: 35% to 95% (with no condensation)
Insulation resistance 20 MΩ min. at 500 VDC
Dielectric strength 1,500 VAC, 50/60 Hz for 1 min
Vibration Destruction 10 to 55 Hz with a 1.5 mm double amplitude for 2 hours each in X, Y, and Z directions
resistance Malfunction 10 to 55 Hz with a 1.5 mm double amplitude for 2 hours each in X, Y, and Z directions
Shock Destruction 500 m/s2 for 3 times each in X, Y, and Z directions
resistance Malfunction 500 m/s2 for 3 times each in X, Y, and Z directions
Degree of protection IEC 60529 IP64
Connection method Pre-wired (standard length: 2 m)
Weight (packed state) Approx. 300 g
Case ABS (Acrylonitrile Butadiene Styrene)
Lens/Display
Methacrylic resin
Material window
Adjuster POM
Cable PVC
Bending radius of cable R18
Accessories Instruction manual

9
 E3JK

Retro-reflective
Sensing method Retro-reflective (without MSR function)
(with MSR function)
Model NPN output E3JK-RN11 E3JK-RN13 E3JK-RN12
Item PNP output E3JK-RP11 E3JK-RP13 E3JK-RP12
6 m [100 mm]* (When using
7 m [100 mm]* (When using E39-R1), 11 m [100 mm]*
Sensing distance E39-R1), 10 m [100 mm]* (When
(When using E39-R2)
using E39-R2)
Standard sensing object Opaque: 75-mm dia. min.
Differential travel −
Directional angle 1.5° min.
Light source (wavelength) Red LED (624 nm) Infrared LED (850 nm) Red LED (624 nm)
Power supply voltage 10 to 30 VDC, including ripple (p-p): 10%
Power DC 30 mA max.
consumption AC −
Load power supply voltage: 30 V max., Load current: 100 mA max., Residual voltage: 3 V max., open-
Control output
collector output (NPN/PNP output depending on model), Light-ON/Dark-ON selectable
Power supply reverse polarity protection, Output short-circuit protection, Mutual interference
Protection circuits
prevention function, and Output reverse polarity protection
Life Mechanical −
expectancy
(relay output) Electrical −

Response time 1 ms max.

Sensitivity adjustment One-turn adjuster
Ambient illumination
Incandescent lamp: 3,000 lx max., Sunlight: 11,000 lx max.
(Receiver side)
Ambient temperature range Operating: −25°C to 55°C, Storage: −40°C to 70°C (with no icing or condensation)
Ambient humidity range Operating: 35% to 85%, Storage: 35% to 95% (with no condensation)
Insulation resistance 20 MΩ min. at 500 VDC
Dielectric strength 1,500 VAC, 50/60 Hz for 1 min
Vibration Destruction 10 to 55 Hz with a 1.5 mm double amplitude for 2 hours each in X, Y, and Z directions
resistance Malfunction 10 to 55 Hz with a 1.5 mm double amplitude for 2 hours each in X, Y, and Z directions
Shock Destruction 500 m/s2 for 3 times each in X, Y, and Z directions
resistance Malfunction 500 m/s2 for 3 times each in X, Y, and Z directions
Degree of protection IEC 60529 IP64
Connection method Pre-wired (standard length: 2 m)
Weight (packed state) Approx. 160 g
Case ABS (Acrylonitrile Butadiene Styrene)
Lens/Display
Methacrylic resin
Material window
Adjuster POM
Cable PVC
Bending radius of cable R18
Accessories Instruction manual
*Values in parentheses indicate the minimum required distances between the Sensors and Reflectors.

10
 E3JK

Sensing method Diffuse-reflective

Model NPN output E3JK-DN11 E3JK-DN12 E3JK-DN13 E3JK-DN14
Item PNP output E3JK-DP11 E3JK-DP12 E3JK-DP13 E3JK-DP14
White paper White paper White paper White paper
Sensing distance
(300 × 300 mm): 2.5 m (100 × 100 mm): 300 mm (300 × 300 mm): 2.5 m (100 × 100 mm): 300 mm
Standard sensing object −
Differential travel 20% max. of sensing distance
Directional angle −
Light source (wavelength) Red LED (624 nm) Infrared LED (850 nm)
Power supply voltage 10 to 30 VDC, including ripple (p-p): 10%
Power DC 30 mA max.
consumption AC −
Load power supply voltage: 30 V max., Load current: 100 mA max., Residual voltage: 3 V max., open-
Control output
collector output (NPN/PNP output depending on model), Light-ON/Dark-ON selectable
Power supply reverse polarity protection, Output short-circuit protection, Mutual interference
Protection circuits
prevention function, and Output reverse polarity protection
Life Mechanical −
expectancy
(relay output) Electrical −

Response time 1 ms max.

Sensitivity adjustment One-turn adjuster
Ambient illumination
Incandescent lamp: 3,000 lx max., Sunlight: 11,000 lx max.
(Receiver side)
Ambient temperature range Operating: −25°C to 55°C, Storage: −40°C to 70°C (with no icing or condensation)
Ambient humidity range Operating: 35% to 85%, Storage: 35% to 95% (with no condensation)
Insulation resistance 20 MΩ min. at 500 VDC
Dielectric strength 1,500 VAC, 50/60 Hz for 1 min
Vibration Destruction 10 to 55 Hz with a 1.5 mm double amplitude for 2 hours each in X, Y, and Z directions
resistance Malfunction 10 to 55 Hz with a 1.5 mm double amplitude for 2 hours each in X, Y, and Z directions
Shock Destruction 500 m/s2 for 3 times each in X, Y, and Z directions
resistance Malfunction 500 m/s2 for 3 times each in X, Y, and Z directions
Degree of protection IEC 60529 IP64
Connection method Pre-wired (standard length: 2 m)
Weight (packed state) Approx. 160 g
Case ABS (Acrylonitrile Butadiene Styrene)
Lens/Display
Methacrylic resin
Material window
Adjuster POM
Cable PVC
Bending radius of cable R18
Accessories Instruction manual

11
 E3JK
Engineering Data (Reference Value)
Parallel Operating Range
Through-beam
E3JK-T@11/T@13 E3JK-T@12/T@14
Parallel distance (m)

2.5

Parallel distance (m)

0.5
E3JK-T 11 E3JK-T 12
2.0 E3JK-T 13 0.4 E3JK-T 14
1.5 0.3

1.0 0.2

0.5 0.1

0 0

−0.5 −0.1

−1.0 −0.2

−1.5 −0.3
Y Y
−2.0 −0.4

−2.5
X X
−0.5
0 20 40 60 80 100 0 2 4 6 8 10
Sensing distance (m) Sensing distance (m)
Retro-reflective
E3JK-R@@1+E39-R1/ E3JK-R@@1+E39-R1S/ E3JK-R@@1+E39-R2/
E3JK-R@@3+E39-R1 E3JK-R@@3+E39-R1S E3JK-R@@3+E39-R2
Parallel distance (mm)
Parallel distance (mm)

Parallel distance (mm)

150 200 Reflector: E39-R1S 250 Reflector: E39-R2
E3JK-R1 Reflector: E39-R1 E3JK-R1 E3JK-R1
E3JK-R3 E3JK-R3 200 E3JK-R3
150
100
150
100
100
50
50 50

0 0 0

−50
−50
50 −100
−100
−150
−100 Y Y Y
−150 −200

X X −250 X
−150 −200
0 2 4 6 8 10 12 0 5 10 15 0 5 10 15 20
Sensing distance (m) Sensing distance (m) Sensing distance (m)
E3JK-R@@2+E39-R1 E3JK-R@@2+E39-R1S E3JK-R@@2+E39-R2
Parallel distance (mm)

Parallel distance (mm)

Parallel distance (mm)

150 200 250

Reflector: E39-R1 Reflector: E39-R1S Reflector: E39-R2
200
150
100
150
100
100
50
50
50

0 0 0

−50
−50
−50
−100
−100
−150
−100 Y Y Y
−150 −200
X X X
−150 −200 −250
0 2 4 6 8 10 0 5 10 15 0 5 10 15 20
Sensing distance (m) Sensing distance (m) Sensing distance (m)
Operating Range
Diffuse-reflective
E3JK-D@@1/D@@3 E3JK-D@@2/D@@4
Distance Y (mm)
Distance Y (mm)

50 30
E3JK-D2
E3JK-D1
E3JK-D4 Y
40 E3JK-D3
20
30
X
20
10
10

0 0
Sensing object:
−10
White paper
(300 × 300 mm)
−10
−20

−30 Y
−20
−40
X Sensing object: White paper (100 × 100 mm)
−50 −30
0 2 4 6 8 0 200 400 600 800 1000
Distance X (m) Distance X (mm)

12
 E3JK

Excess Gain Ratio vs. Set Distance

Through-beam
E3JK-T@11/T@13 E3JK-T@12/T@14
Excess gain ratio

100

Excess gain ratio

100
E3JK-T11 E3JK-T12
E3JK-T13 E3JK-T14

10 10

Operating Operating 1
level 1 level

0.1 0.1
0 20 40 60 80 100 0 5 10 15 20
Distance (m) Distance (m)

Retro-reflective
E3JK-R@@1+E39-R1/ E3JK-R@@1+E39-R1S/ E3JK-R@@1+E39-R2/
E3JK-R@@3+E39-R1 E3JK-R@@3+E39-R1S E3JK-R@@3+E39-R2
100 100
Excess gain ratio

Excess gain ratio

100
Excess gain ratio

E3JK-R1 E3JK-R1 E3JK-R1

E3JK-R3 E3JK-R3 E3JK-R3

10 10 10

Operating 1 Operating 1 Operating 1

level level level

Reflector: E39-R1 Reflector: E39-R1S Reflector: E39-R2

0.1 0.1 0.1
0 2 4 6 8 10 12 0 2 4 6 8 10 12 14 16 18 20 0 2 4 6 8 10 12 14 16 18 20
Distance (m) Distance (m) Distance (m)

E3JK-R@@2+E39-R1 E3JK-R@@2+E39-R1S E3JK-R@@2+E39-R2

Excess gain ratio

Excess gain ratio

Excess gain ratio

100 100 100

Reflector: E39-R1 Reflector: E39-R1S Reflector: E39-R2

10 10 10

Operating 1 Operating Operating

level level 1 level 1

0.1 0.1 0.1

0 2 4 6 8 10 12 0 2 4 6 8 10 12 14 16 18 20 0 2 4 6 8 10 12 14 16 18 20
Distance (m) Distance (m) Distance (m)
Diffuse-reflective
E3JK-D@@1/D@@3 E3JK-D@@2/D@@4
Excess gain ratio

Excess gain ratio

100 100
Sensing object: White paper (100 × 100 mm)
Sensing object: White paper (300 × 300 mm)
E3JK-D1 E3JK-D2
E3JK-D3 E3JK-D4

10

10

Operating 1
level

Operating 1 0.1
level 0 2 4 6 0 100 200 300 400 500
Distance (m) Distance (mm)

13
 E3JK
I/O Circuit Diagrams
Relay Output Models
Timing chart
Model Output circuit
Light-ON Dark-ON
Brown
Power
Indicator
E3JK-TR11-L * (green) 24 to 240 VAC
24 to 240 VDC
E3JK-TR12-L * Photoelectric
Sensor Power
E3JK-TR13-L * main
Circuit
Source

E3JK-TR14-L *
Blue

Operation Indicator
E3JK-TR11-D * (orange) Brown
Stability
E3JK-TR12-D * Indicator
Incident light Incident light
E3JK-TR13-D * No incident light No incident light
(green) 24 to 240 VAC
24 to 240 VDC
Photoelectric
E3JK-TR14-D * Operation Indicator ON Operation Indicator ON Sensor Power
Source
main
E3JK-RR11 (orange) OFF (orange) OFF Circuit

E3JK-RR12 Relay
Operate
Relay
Operate
Blue
Reset Reset
E3JK-RR13 Conducting
Conducting
E3JK-DR11 Output Tc-Ta
Not conducting
Output Tc-Ta
Not conducting White
E3JK-DR12 Conducting Conducting Tc
Output Tc-Tb Output Tc-Tb Contact output (SPDT),
E3JK-DR13 Not conducting Not conducting Black
Ta 250 VAC, 3 A max.,
E3JK-DR14 Gray
5 VDC, 10 mA min.
Tb

DC SSR Output Models

Timing chart
Model Output circuit
Light-ON Dark-ON
E3JK-TN11-L *
E3JK-TP11-L * Power
Brown 10 to 30 VDC

E3JK-TN12-L * Indicator
(green)
E3JK-TP12-L * Photoelectric
Sensor
E3JK-TN13-L * main
Circuit
E3JK-TP13-L *
E3JK-TN14-L * Blue 0V
E3JK-TP14-L *
E3JK-TN11-D *
E3JK-TN12-D *
E3JK-TN13-D * Incident light Incident light
Operation Indicator
(orange) Brown
E3JK-TN14-D * No incident light No incident light Stability
10 to 30 VDC
Indicator
E3JK-RN11 Operation Indicator ON Operation Indicator ON
(green) Load
(orange) OFF (orange) OFF
E3JK-RN12 Photoelectric Black
ON ON Sensor
E3JK-RN13 Output
transistor OFF
Output
transistor OFF
main
Circuit 100 mA max.
E3JK-DN11 Operate Operate
Load Load Blue
E3JK-DN12 (e.g., relay) Reset (e.g., relay) Reset 0V

E3JK-DN13
E3JK-DN14
E3JK-TP11-D *
E3JK-TP12-D *
E3JK-TP13-D * Incident light Incident light
Operation Indicator
(orange) Brown
E3JK-TP14-D * No incident light No incident light Stability
10 to 30 VDC
Indicator
E3JK-RP11 Operation Indicator ON Operation Indicator ON
(green)
(orange) OFF (orange) OFF
E3JK-RP12 Photoelectric
Sensor
Black 100 mA max.
ON ON
E3JK-RP13 Output
transistor OFF
Output
transistor OFF
main
Circuit
E3JK-DP11 Operate Operate Load
Load Load
E3JK-DP12 (e.g., relay) Reset (e.g., relay) Reset Blue
0V
E3JK-DP13
E3JK-DP14
Note: Connect the brown cable to any polarity and the blue cable to the power supply because there is no polarity on the Emitter side.
*For the Through-beam Sensor, the Emitter is listed as E3JK-T@11-L, E3JK-T@12-L and the Receiver is listed as E3JK-T@11-D, E3JK-T@12-D in the table.
Confirm the models to order in “Ordering Information.”

14
 E3JK
Safety Precautions
Refer to Warranty and Limitations of Liability.
WARNING
This product is not designed or rated for
ensuring safety of persons either directly or
indirectly.
Do not use it for such purposes.

Caution
Do not wire the product incorrectly.
Do not use this product with a damaged case or
cable.

Do not disassemble, repair, or modify this

product.
Doing so may lead to explosion, fire, or product
failure.

Precautions for Safe Use

The following precautions must be observed to ensure safe
operation of the Sensor.
1. Do not use the Sensor in environments subject to
flammable, explosive or corrosive gases.
2. Do not use this product in an environment in which oil or
chemicals are present.
3. Do not use this product under water, in the rain, or outdoors.
4. Do not use this product under conditions that exceed or in
an environment that exceeds the ratings.
5. When using an AC power supply, do not use a power
supply that includes high frequencies (such as an inverter).
6. Do not use this product in a location subject to direct
sunlight.
7. Do not use this product in a location in which the product will
be subject to direct vibrations or impacts.
8. Do not use thinner, alcohol, or other organic solvents with
this product.
9. When disposing of the Sensor, treat it as industrial waste.

Precautions for Correct Use

• If the product is wired to high-voltage power lines and power
lines in the same pipe or the same duct, the product may
malfunction or be damaged due to induction. Therefore, in
principle, perform these two types of wiring separately or
use shielded cords.
• Do not apply excessive force to the cables.
• When using a commercially available switching regulator,
be sure to install an FG (frame ground terminal).
• The time between the product being turned ON and sensing
being possible is 100 ms, so wait at least 100 ms after
turning the product ON before using it. If the load and the
product are connected to different power supplies, be sure
to turn the product ON first.
• An output pulse may be generated when the product is
turned OFF, so we recommend turning the load or the load
line OFF first.
• LED Safety
E3JK-TR@, E3JK-RR@@ and E3JK-DR@@ are classified
EXEMPT GROUP, based on IEC 62471.

15
 E3JK
(Unit: mm)
Dimensions Tolerance class IT16 applies to dimensions in this datasheet unless otherwise specified.

Sensors
Through-beam <Emitter> Power Indicator (green)
E3JK-T@1@ E3JK-T@1@-L

18 50
1.3

Optical axis
4.8 40 50
14.7 Two, 4.5-dia. M4
20.2 mounting holes 5
Recommended
6-dia. vinyl-insulated round cable
Torque: 0.8 N⋅m
5 (Conductor cross section: 0.3 mm2, Insulator
(1.2 N⋅m max.) 40 diameter: 1.5 mm), Standard length: 2 m,
12.8 Bending radius: R18

<Receiver> Operation Indicator (orange) Stability Indicator (green)

E3JK-T@1@-D

Sensitivity adjuster Operation selector

18 50
2

Optical axis
4.8 40 50
14.7
Two, 4.5-dia. M4
20.2 mounting holes 5
Recommended 6-dia. vinyl-insulated round cable
Torque: 0.8 N⋅m 5 (Conductor cross section: 0.3 mm2, Insulator
(1.2 N⋅m max.) 40 diameter: 1.5 mm), Standard length: 2 m,
Bending radius: R18
12.8

Retro-reflective/ Operation Indicator (orange) Stability Indicator (green)

Diffuse-reflective
E3JK-R@1@
E3JK-D@1@
Sensitivity adjuster Operation selector

18 50

Emitter 2

Optical axis
14.7 Receiver
7
7 40 50
14.7
27.2 Two, 4.5-dia. M4
mounting holes 5
Recommended 6-dia. vinyl-insulated round cable
Torque: 0.8 N⋅m 5 (Conductor cross section: 0.3 mm2, Insulator
(1.2 N⋅m max.) 40 diameter: 1.5 mm), Standard length: 2 m,
Bending radius: R18
12.8

16
 E3JK

Accessories
Mounting Bracket (Order separately)

Mounting Bracket 18±0.1

E39-L40 Radius: 3.2 6-dia. hole Radius: 3.2

12 22
10±0.1
6.4
4 9 6.4
Two, Radius: 5
42±0.1 7

50 Two, Radius: 5
2
40±0.1 5

Two, 4.4-dia. hole

Material: Iron Two, Radius: 5
Two, Radius: 5.6 Two, Radius: 5

Radius: 2.2 60
Radius: 56.6±0.1
31.2
21.9
60°
45°
Radius: 2.2 4.4
24
10°
58

With Mounting Bracket Attached 47

40 6.4 21

5.6
6.6 6-dia. 6.4
hole
7
18
39.5
Through-beam Retro-reflective/
Diffuse-reflective
Mounting Bracket Mounting Bracket

Optical axis Mounting Holes

Optical axis
Two, M6 holes
30.2 37.2
2 2
42

Reflector (Order separately)

E39-R1 E39-R2
E39-R1S
80.8
40.3 74.5
Four, 3.5-dia. holes 7.5
Two, 3.5-dia. holes 34 7 7
7.5
7

59.9 52 59.9 52

8 Material:
Material:
Reflective surface: acrylic
Reflective surface: acrylic 1.6 2.7
Rear surface: ABS 1.6 7 2.7
Rear surface: ABS 6.5 34

17
 MEMO

18
 Terms and Conditions Agreement
Read and understand this catalog.
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you
have any questions or comments.

Warranties.
(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship
for a period of twelve months from the date of sale by Omron (or such other period expressed in writing
by Omron). Omron disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE
PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE PRODUCTS WILL
SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.
Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the
Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s
election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof)
the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase
price of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any
other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were properly handled,
stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any
Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability
or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system
assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in
writing, are not to be construed as an amendment or addition to the above warranty.
See http://www.omron.com/global/ or contact your Omron representative for published information.

Limitation on Liability; Etc.

OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,
WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.

Suitability of Use.
Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the
combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable
third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself
is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine,
system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product
with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE
QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.

Programmable Products.
Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence thereof.

Performance Data.
Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining
suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate
it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.

Change in Specifications.
Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our
practice to change part numbers when published ratings or features are changed, or when significant construction changes are
made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers
may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at
any time to confirm actual specifications of purchased Product.

Errors and Omissions.

Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is
assumed for clerical, typographical or proofreading errors or omissions.
Note: Do not use this document to operate the Unit.
OMRON Corporation Industrial Automation Company Authorized Distributor:
Kyoto, JAPAN Contact : www.ia.omron.com
Regional Headquarters

OMRON EUROPE B.V. OMRON ELECTRONICS LLC

Wegalaan 67-69, 2132 JD Hoofddorp 2895 Greenspoint Parkway, Suite 200
The Netherlands Hoffman Estates, IL 60169 U.S.A.
Tel: (31) 2356-81-300 Fax: (31) 2356-81-388 Tel: (1) 847-843-7900 Fax: (1) 847-843-7787

OMRON ASIA PACIFIC PTE. LTD. OMRON (CHINA) CO., LTD. ©OMRON Corporation 2013-2024 All Rights Reserved.
438B Alexandra Road, #08-01/02 Alexandra Room 2211, Bank of China Tower, In the interest of product improvement,
Technopark, Singapore 119968 200 Yin Cheng Zhong Road, specifications are subject to change without notice.
Tel: (65) 6835-3011 Fax: (65) 6835-3011 PuDong New Area, Shanghai, 200120, China CSM_8_6
Tel: (86) 21-6023-0333 Fax: (86) 21-5037-2388 Cat. No. E432-E1-07 0424 (0313)