SAFETY DATA SHEET

1. Identification
Product identifier SHEETROCK® Brand All Purpose Joint Compound (Powdered)
Other means of identification
SDS number 61000020002
Synonyms Joint Compound , Taping Compound, Mud, Finishing Compound
Recommended use Interior use.
Recommended restrictions Use in accordance with manufacturer's recommendations.
Manufacturer/Importer/Supplier/Distributor information
Company name United States Gypsum Company
Address 550 West Adams Street
Chicago, Illinois 60661-3637
Telephone 1-800-874-4968
Website www.usg.com
Emergency phone number 1-800-507-8899

2. Hazard(s) identification
Physical hazards Not classified.

Health hazards Carcinogenicity Category 1A

Specific target organ toxicity, repeated Category 2 (Lungs)
exposure
OSHA defined hazards Not classified.

Label elements

Signal word Danger

Hazard statement May cause cancer by inhalation. May cause damage to organs (Lungs) through prolonged or
repeated exposure.
Precautionary statement
Prevention Obtain special instructions before use. Do not handle until all safety precautions have been read
and understood. Do not breathe dust. Wear protective gloves/protective clothing/eye
protection/face protection.
Response If exposed or concerned: Get medical advice/attention.
Storage Store locked up.
Disposal Dispose of contents/container in accordance with local/regional/national/international regulations.
Hazard(s) not otherwise None known.
classified (HNOC)
Supplemental information None.

3. Composition/information on ingredients
Mixtures
Chemical name CAS number %
Limestone 1317-65-3 > 60

Attapulgite 12174-11-7 < 20

Mica 12001-26-2 < 20

SHEETROCK® Brand All Purpose Joint Compound (Powdered) SDS US

917158 Version #: 01 Revision date: - Issue date: 19-April-2018 1/7
 Starch 9005-25-8 <5

Impurities
Chemical name CAS number %
Crystalline silica (Quartz) 14808-60-7 <4

Composition comments All concentrations are in percent by weight.

Raw materials in this product contain respirable crystalline silica as an impurity. The weight
percent of respirable crystalline silica found in this product is < 4.0%. Exposures to respirable
crystalline silica during the normal use of this product must be determined by workplace hygiene
testing.

4. First-aid measures
Inhalation Dust irritates the respiratory system, and may cause coughing and difficulties in breathing. Move
injured person into fresh air and keep person calm under observation. Get medical attention if
symptoms persist.
Skin contact Contact with dust: Rinse area with plenty of water. Get medical attention if irritation develops or
persists.
Eye contact Dust in the eyes: Do not rub eyes. Flush thoroughly with water. If irritation occurs, get medical
assistance.
Ingestion Rinse mouth. Get medical attention if symptoms occur.
Most important Under normal conditions of intended use, this material does not pose a risk to health. Dust may
symptoms/effects, acute and irritate throat and respiratory system and cause coughing.
delayed
Indication of immediate Provide general supportive measures and treat symptomatically.
medical attention and special
treatment needed
General information Ensure that medical personnel are aware of the material(s) involved.

5. Fire-fighting measures
Suitable extinguishing media Use fire-extinguishing media appropriate for surrounding materials.
Unsuitable extinguishing Not applicable.
media
Specific hazards arising from Not a fire hazard.
the chemical
Special protective equipment Selection of respiratory protection for firefighting: follow the general fire precautions indicated in
and precautions for firefighters the workplace. Self-contained breathing apparatus and full protective clothing must be worn in
case of fire.
Fire fighting Use standard firefighting procedures and consider the hazards of other involved materials.
equipment/instructions
Specific methods Cool material exposed to heat with water spray and remove it if no risk is involved.
General fire hazards No unusual fire or explosion hazards noted.

6. Accidental release measures

Personal precautions, Use a NIOSH/MSHA approved respirator if there is a risk of exposure to dust/fume at levels
protective equipment and exceeding the exposure limits. See Section 8 of the SDS for Personal Protective Equipment.
emergency procedures
Methods and materials for Vacuum up the spilled material. Vacuums used for this purpose should be equipped with HEPA
containment and cleaning up filters. Collect in approved containers and seal securely. Containers must be labeled. For waste
disposal, see Section 13 of the SDS.
Environmental precautions Avoid discharge to drains, sewers, and other water systems.

7. Handling and storage

Precautions for safe handling Minimize dust production when mixing, sanding, or opening and closing bags. Avoid inhalation of
dust. Wear appropriate personal protective equipment. Wash hands after handling. Observe good
industrial hygiene practices and use appropriate lifting techniques.
Conditions for safe storage, Store in a cool, dry, well-ventilated place. Store in a closed container away from incompatible
including any incompatibilities materials. Protect from moisture. Keep away from heat. Do not use if material has spoiled, i.e.,
there is a moldy appearance or an unpleasant odor. Keep containers closed when not in use.

SHEETROCK® Brand All Purpose Joint Compound (Powdered) SDS US

917158 Version #: 01 Revision date: - Issue date: 19-April-2018 2/7
8. Exposure controls/personal protection
Occupational exposure limits
US. OSHA Specifically Regulated Substances (29 CFR 1910.1001-1053)
Impurities Type Value
Crystalline silica (Quartz) TWA 0.05 mg/m3
(CAS 14808-60-7)
US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000)
Components Type Value Form

Limestone (CAS 1317-65-3) PEL 5 mg/m3 Respirable fraction.

15 mg/m3 Total dust.
Starch (CAS 9005-25-8) PEL 5 mg/m3 Respirable fraction.
15 mg/m3 Total dust.
US. OSHA Table Z-3 (29 CFR 1910.1000)
Components Type Value
Mica (CAS 12001-26-2) TWA 20 mppcf
Impurities Type Value Form
Crystalline silica (Quartz) TWA 0.1 mg/m3 Respirable.
(CAS 14808-60-7)
2.4 mppcf Respirable.
US. ACGIH Threshold Limit Values
Components Type Value Form

Mica (CAS 12001-26-2) TWA 3 mg/m3 Respirable fraction.

Starch (CAS 9005-25-8) TWA 10 mg/m3
Impurities Type Value Form
Crystalline silica (Quartz) TWA 0.025 mg/m3 Respirable fraction.
(CAS 14808-60-7)
US. NIOSH: Pocket Guide to Chemical Hazards
Components Type Value Form

Limestone (CAS 1317-65-3) TWA 5 mg/m3 Respirable.

10 mg/m3 Total
Mica (CAS 12001-26-2) TWA 3 mg/m3 Respirable.
Starch (CAS 9005-25-8) TWA 5 mg/m3 Respirable.
10 mg/m3 Total
Impurities Type Value Form
Crystalline silica (Quartz) TWA 0.05 mg/m3 Respirable dust.
(CAS 14808-60-7)
Biological limit values No biological exposure limits noted for the ingredient(s).
Appropriate engineering Provide sufficient ventilation for operations causing dust formation. Observe occupational
controls exposure limits and minimize the risk of exposure. We recommend using wet sanding or vacuum
sanding practices to reduce dust exposure.
Individual protection measures, such as personal protective equipment
Eye/face protection Wear approved safety goggles.
Skin protection
Hand protection It is a good industrial hygiene practice to minimize skin contact. For prolonged or repeated skin
contact use suitable protective gloves.
Skin protection
Other Normal work clothing (long sleeved shirts and long pants) is recommended.
Respiratory protection If engineering controls do not maintain airborne concentrations below recommended exposure
limits (where applicable) or to an acceptable level (in countries where exposure limits have not
been established), an approved respirator must be worn. Use a NIOSH/MSHA approved respirator
if there is a risk of exposure to dust/fume at levels exceeding the exposure limits. Use a
NIOSH/MSHA approved air purifying respirator as needed to control exposure. Consult with
respirator manufacturer to determine respirator selection, use, and limitations. Use positive
pressure, air-supplied respirator for uncontrolled releases or when air purifying respirator
limitations may be exceeded. Follow respirator protection program requirements (OSHA 1910.134
and ANSI Z88.2) for all respirator use.
SHEETROCK® Brand All Purpose Joint Compound (Powdered) SDS US
917158 Version #: 01 Revision date: - Issue date: 19-April-2018 3/7
 Thermal hazards None.
General hygiene Always observe good personal hygiene measures, such as washing after handling the material
considerations and before eating, drinking, and/or smoking. Routinely wash work clothing and protective
equipment separately from regular wash. Observe any medical surveillance requirements.

9. Physical and chemical properties

Appearance
Physical state Solid.
Form Powder.
Color White to off-white.
Odor Low to no odor.
Odor threshold Not applicable.
pH 7.5 - 9.9
Melting point/freezing point Not applicable.
Initial boiling point and boiling Not applicable.
range
Flash point Not applicable.
Evaporation rate Not applicable.
Flammability (solid, gas) Not applicable.
Upper/lower flammability or explosive limits
Flammability limit - lower Not applicable.
(%)
Flammability limit - upper Not applicable.
(%)
Explosive limit - lower (%) Not applicable.
Explosive limit - upper (%) Not applicable.
Vapor pressure Not applicable.
Vapor density Not applicable.
Relative density 1.4 - 1.8 (H2O=1)
Solubility(ies)
Solubility (water) Soluble in water.
Partition coefficient Not applicable.
(n-octanol/water)
Auto-ignition temperature Not applicable.
Decomposition temperature Not applicable.
Viscosity Not applicable.
Other information
Bulk density 90 - 112 lb/ft³
VOC None detected.

10. Stability and reactivity

Reactivity The product is stable and non-reactive under normal conditions of use, storage and transport.
Chemical stability Material is stable under normal conditions.
Possibility of hazardous Hazardous polymerization does not occur.
reactions
Conditions to avoid Exposure to moisture.
Incompatible materials None known.
Hazardous decomposition Above 1472°F (800°C) limestone (CaCO3) can decompose to lime (CaO) and release carbon
products dioxide (CO2).

11. Toxicological information

Information on likely routes of exposure
Inhalation Inhalation of dusts may cause respiratory irritation. Prolonged and repeated exposure to airborne
respirable crystalline silica can cause silicosis and/or lung cancer.

SHEETROCK® Brand All Purpose Joint Compound (Powdered) SDS US

917158 Version #: 01 Revision date: - Issue date: 19-April-2018 4/7
 Skin contact Under normal conditions of intended use, this material does not pose a skin hazard.
Eye contact Direct contact with airborne particulates may cause temporary irritation.
Ingestion May cause discomfort if swallowed.
Symptoms related to the Dust may irritate eyes and mucous membranes of the nose, throat and upper respiratory system
physical, chemical and causing sneezing and/or coughing.
toxicological characteristics
Information on toxicological effects
Acute toxicity Not expected to be a hazard under normal conditions of intended use.
Components Species Test Results
Starch (CAS 9005-25-8)
Acute
Dermal
LD50 Rabbit > 5000 mg/kg
Oral
LD50 Rat > 50000 mg/kg
Skin corrosion/irritation Prolonged or repeated skin contact may cause drying, cracking, or irritation.
Serious eye damage/eye Direct contact with eyes may cause temporary irritation.
irritation
Respiratory or skin sensitization
Respiratory sensitization Not a respiratory sensitizer.
Skin sensitization This product is not expected to cause skin sensitization.
Germ cell mutagenicity Data does not suggest that this product or any components present at greater than 0.1% are
mutagenic or genotoxic.
Carcinogenicity Repeated and prolonged exposure to high levels of respirable crystalline silica may cause cancer.
IARC Monographs. Overall Evaluation of Carcinogenicity
Crystalline silica (Quartz) (CAS 14808-60-7) 1 Carcinogenic to humans.
NTP Report on Carcinogens
Crystalline silica (Quartz) (CAS 14808-60-7) Known To Be Human Carcinogen.
OSHA Specifically Regulated Substances (29 CFR 1910.1001-1053)
Crystalline silica (Quartz) (CAS 14808-60-7) Cancer
Reproductive toxicity Not expected to be a reproductive hazard.
Specific target organ toxicity - No data available, but none expected.
single exposure
Specific target organ toxicity - May damage lung tissue through repeated and prolonged exposure to high levels of respirable
repeated exposure crystalline silica particles.
Aspiration hazard Due to the physical form of the product it is not an aspiration hazard.
Chronic effects Prolonged and routine inhalation of high levels of respirable crystalline silica particles can lead to
the lung disease known as silicosis. Some studies show excess numbers of cases of
scleroderma, connective tissue disorders, lupus, rheumatoid arthritis, chronic kidney diseases and
end-stage kidney disease in workers exposed to respirable crystalline silica. Pre-existing skin and
respiratory conditions including dermatitis, asthma and chronic lung disease might be aggravated
by exposure. Occupational exposure to respirable dust and respirable crystalline silica should be
monitored and controlled.

12. Ecological information

Ecotoxicity The product is not classified as environmentally hazardous. However, this does not exclude the
possibility that large or frequent spills can have a harmful or damaging effect on the environment.
Persistence and degradability No data available.
Bioaccumulative potential Bioaccumulation is not expected.
Mobility in soil No data available.
Other adverse effects None expected.

13. Disposal considerations

Disposal instructions Dispose in accordance with applicable federal, state, and local regulations. Recycle responsibly.
Local disposal regulations Dispose of in accordance with local regulations.
SHEETROCK® Brand All Purpose Joint Compound (Powdered) SDS US
917158 Version #: 01 Revision date: - Issue date: 19-April-2018 5/7
Hazardous waste code Not regulated.
Waste from residues / unused Dispose of in accordance with local regulations.
products
Contaminated packaging Dispose of in accordance with local regulations.

14. Transport information

DOT
Not regulated as dangerous goods.
IATA
Not regulated as dangerous goods.
IMDG
Not regulated as dangerous goods.
Transport in bulk according to Not applicable.
Annex II of MARPOL 73/78 and
the IBC Code

15. Regulatory information

US federal regulations This product is a "Hazardous Chemical" as defined by the OSHA Hazard Communication
Standard, 29 CFR 1910.1200.
TSCA Section 12(b) Export Notification (40 CFR 707, Subpt. D)
Not regulated.
CERCLA Hazardous Substance List (40 CFR 302.4)
Not listed.
SARA 304 Emergency release notification
Not regulated.
OSHA Specifically Regulated Substances (29 CFR 1910.1001-1053)
Crystalline silica (Quartz) (CAS 14808-60-7) Cancer
lung effects
immune system effects
kidney effects
Superfund Amendments and Reauthorization Act of 1986 (SARA)
SARA 302 Extremely hazardous substance
Not listed.
SARA 311/312 Hazardous Yes
chemical
Classified hazard Carcinogenicity
categories Specific target organ toxicity (single or repeated exposure)
SARA 313 (TRI reporting)
Not regulated.

Other federal regulations

Clean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) List
Not regulated.
Clean Air Act (CAA) Section 112(r) Accidental Release Prevention (40 CFR 68.130)
Not regulated.
Safe Drinking Water Act Not regulated.
(SDWA)
US state regulations
US. Massachusetts RTK - Substance List
Crystalline silica (Quartz) (CAS 14808-60-7)
Limestone (CAS 1317-65-3)
Mica (CAS 12001-26-2)
Starch (CAS 9005-25-8)
US. New Jersey Worker and Community Right-to-Know Act
Crystalline silica (Quartz) (CAS 14808-60-7)
Limestone (CAS 1317-65-3)
Mica (CAS 12001-26-2)

SHEETROCK® Brand All Purpose Joint Compound (Powdered) SDS US

917158 Version #: 01 Revision date: - Issue date: 19-April-2018 6/7
 US. Pennsylvania Worker and Community Right-to-Know Law
Crystalline silica (Quartz) (CAS 14808-60-7)
Limestone (CAS 1317-65-3)
Mica (CAS 12001-26-2)
Starch (CAS 9005-25-8)
US. Rhode Island RTK
Crystalline silica (Quartz) (CAS 14808-60-7)
Limestone (CAS 1317-65-3)
Mica (CAS 12001-26-2)
Starch (CAS 9005-25-8)
California Proposition 65
WARNING: This product can expose you to chemicals including Crystalline silica (Quartz), which is known to
the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov.

California Proposition 65 - CRT: Listed date/Carcinogenic substance

Attapulgite (CAS 12174-11-7) Listed: December 28, 1999
Crystalline silica (Quartz) (CAS 14808-60-7) Listed: October 1, 1988
US. California. Candidate Chemicals List. Safer Consumer Products Regulations (Cal. Code Regs, tit. 22, 69502.3,
subd. (a))
Crystalline silica (Quartz) (CAS 14808-60-7)
International Inventories
Country(s) or region Inventory name On inventory (yes/no)*
United States & Puerto Rico Toxic Substances Control Act (TSCA) Inventory No
*A "Yes" indicates this product complies with the inventory requirements administered by the governing country(s).
A "No" indicates that one or more components of the product are not listed or exempt from listing on the inventory administered by the governing
country(s).

16. Other information, including date of preparation or last revision

Issue date 19-April-2018
Revision date -
Version # 01
Further information Crystalline silica: Raw materials in this product may contain respirable crystalline silica.
Exposures to respirable crystalline silica are not expected during the normal use of this product.
However, actual levels must be determined by workplace hygiene testing. Prolonged and repeated
exposure to airborne free respirable crystalline silica can result in lung disease (i.e., silicosis)
and/or lung cancer.

Attapulgite: Carcinogenic to experimental animals via a route of exposure not relevant to human
exposure per ACGIH.

NFPA Ratings:
Health: 1
Flammability: 0
Physical hazard: 0

Hazard Scale: 0 = Minimal 1 = Slight 2 = Moderate 3 = Serious 4 = Severe

NFPA ratings
0
1 0

List of abbreviations NFPA: National Fire Protection Association.

References Registry of Toxic Effects of Chemical Substances (RTECS)
HSDB® - Hazardous Substances Data Bank
Torben et al. (2001). Environmental and Health Assessment of Substances in Household
Detergents and Cosmetic Products.
Disclaimer This information is provided without warranty. The information is believed to be correct. This
information should be used to make an independent determination of the methods to safeguard
workers and the environment.

SHEETROCK® Brand All Purpose Joint Compound (Powdered) SDS US

917158 Version #: 01 Revision date: - Issue date: 19-April-2018 7/7