STRUCTURAL

ANALYSIS & REPORT

of

PROPOSE FOUR-STOREY
COMMERCIAL BUILDING
PENABLANCA, CAGAYAN

SUBMITTED BY:

QUITORAS, DEXTER B.
VERACION, GEENO R.

SUBMITTED TO:
ENGR. RONIE M. PIEDAD
 TABLE OF CONTENTS
Design Criteria…………………………………………………………………………....1

Structural Design Parameters……..…………………………………………………..….2

Assumed Soil Bearing Capacity……..……………………………………………….…..2

Design Codes……………………..…………………………………………………..…..2

Load Combinations………………..………………………………………………….…..2

Design Application………………..………………………………………………….…..3

Floor Diagphragm……..………………………………………………………………….3

Soft Story……..…………………………………………….…………………………….3

Story Drift……..…………………………………………….…………………………....3

Most Critical Beams……..………………………………….…………………………....7

Most Critical Columns……..………………………………….…………………….…...16

Footing Design…….……..………………………………….…………………………...19

Footing Layout..…….…………………………………….………………………………29

Structural Results…..…….………………………………….……………………………30
SUBJECT : STRUCTURAL ANALYSIS AND DESIGN REPORT
PROJECT : PROPOSED FOUR-STORY COMMERCIAL BUILDING
OWNER : MEDICAL COLLEGES OF NORTHERN PHILIPPINES – INTERNATIONAL
SCHOOL OF ASIA AND THE PACIFIC
LOCATION : ALIMANAO HILLS, PENABLANCA, CAGAYAN

I. DESIGN CRITERIA

A. Dead Load
A.1 Concrete Weight = 24 kN/m3
A.2 6” CHB Plastered Both Face = 3.11 kPa
A.3 Ground Floor Load (One-way) = 7.68 kPa
A.4 Ground Floor Load (Two-way) = 7.68 kPa
A.5 Second Floor Load (One-way) = 4.68 kPa
A.6 Second Floor Load (Two-way) = 4.68 kPa
A.7 Third Floor Load (One-way) = 4.68 kPa
A.8 Third Floor Load (Two-way) = 4.68 kPa
A.9 Fourth Floor Load (One-way) = 4.68 kPa
A.10 Fourth Floor Load (Two-way) = 4.68 kPa
A.11 Limiting Main Slab Thickness is 4 inches excluding finish.
Limiting Average Stair Thickness is 4 inches excluding finish.

B. Live Load
Occupancy: Essential Facility (School)
B.1 Classrooms = 1.9 kPa
B.2 Corridors = 3.8 kPa
B.3 Exit Facilities (Stairs) = 3.8 kPa

C. Roof Live Load

C.1 34.87% Slope = 0.75 kPa
Tributary Width = 3.4 m
C.2 34.87% Slope = 0.75 kPa
Tributary Width = 3.4 m
C.3 34.87% Slope = 1.0 kPa
Tributary Width = 3.05 m

D. Wind Load

Method: Components & Cladding

Risk Category = III

Basic Wind Speed = 300 kph
Exposure Category =B
Kzt Factor = 1.00
Adjustment Factor = 1.09
Truss 1 & 2:
Direct Pressure = 4.69 kN/m
Uplift Pressure (Z1) = 9.44 kN/m
Uplift Pressure (Z2) = 13.36 kN/m
Truss 3:
Direct Pressure = 2.34 kN/m
Uplift Pressure (Z1) = 6.63 kN/m

1
 Uplift Pressure (Z2) = 10.21 kN/m

E. Seismic Load

Structural System: Reinforced Concrete Special Moment Resisting Frame

Code = UBC 1997

Zone 4 = 0.40
Importance Factor = 1.5
R factor = 8.5
Soil Profile Type =D
Near Source factor (Na) = 1.0
Near Source factor (Nv) = 1.0
Ct Value = 0.0731
Period = 0.4851 seconds

II. STRUCTURAL DESIGN PARAMETERS

1.0 Concrete, f’c = 21 MPa (3045.79 psi) @ 28 days

2.0 Reinforcing Steel Bars, fy

Main = 276 MPa (Grade 40)

Secondary = 227.7 MPa (Grade 33)

3.0 Concrete Hollow Blocks: conform ASTM C-145

4.0 Structural Steel A36

III. ASSUMED SOIL BEARING CAPACITY = 180 kPa at 2.494 m footing depth

IV. DESIGN CODE: NSCP 2015 Edition, UBC 1997, ASCE-7-2010

V. LOAD COMBINATION:

DRIFT Combo:

1.2Dead + 1.6RoofLive + 0.5Wind

1.2Dead + 0.5Live + 0.5RoofLive + 1Wind
1.2Dead + 0.5Live + 1Seismic-H
1.2Dead + 0.5Live + 1Seismic-V
0.9Dead + 1Wind
0.9Dead + 1Seismic-H
0.9Dead + 1Seismic-V

USD/LRFD Combo:

1.4Dead
1.2Dead + 1.6Live + 0.5RoofLive
1.2Dead + 0.5Live + 1.6RoofLive
1.42Dead + 1Live + 0.5Rooflive + 1Seismic-H + 0.3Seismic-V
1.42Dead + 1Live + 0.5Rooflive + 0.3Seismic-H + 1Seismic-V
0.68Dead + 1Seismic-H + 0.3Seismic-V
0.68Dead + 0.3Seismic-H + 1Seismic-V

2
VI. DESIGN APPLICATION: STAAD.Pro Connect Edition & Excel

****************************************************
* *
* STAAD.Pro CONNECT Edition *
* Version 22.09.00.115 *
* Proprietary Program of *
* Bentley Systems, Inc. *
* Date= DEC 16, 2024 *
* Time= 14:37:34 *
* *
* Licensed to: only@ ::LAVteam::® *
****************************************************

FLOOR DIAPHRAGM
*******************************************************************************

FLOOR DIAPHRAGM UNIT - KN METER

--------------- ----------------

NO. TYPE FL. LEVEL FL. WT CENTRE OF MASS MASTER JOINT NO.
X Z
_
1 RIGID 2.494 2653.74 11.436 5.221 257
2 RIGID 5.964 3551.93 10.611 4.507 258
3 RIGID 8.964 3608.11 10.972 4.532 259
4 RIGID 11.964 3437.48 10.763 4.534 260

SOFT STORY CHECK

VERTICAL STRUCTURAL IRREGULARITIES : SOFT STORY CHECK - ASCE/SEI 7-05

-------- ---------- --------------

STORY FL. LEVEL IN METER S T A T U S

----- ----------------- --------------------
X Z

1 2.49 OK OK
2 5.96 OK OK
3 8.96 OK OK
4 11.96 OK OK

NOTE : NO SOFT STOREY IS DETECTED.

STORY DRIFT 0.004200

STORY HEIGHT LOAD AVG. DISP(CM ) DRIFT(CM ) RATIO STATUS

------------------------------------------------------------------------------------------
(METER) X Z X Z

BASE= 0.00 ALLOW. DRIFT = L / 238

_

1 0.00 101 0.0000 0.0000 0.0000 0.0000 L /999999 PASS

102 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
103 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
3
 104 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
105 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
106 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
107 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
108 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
109 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
110 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
111 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
112 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
113 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
114 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
115 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
116 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
117 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
118 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
119 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
120 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
121 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
122 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
123 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
124 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
125 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
126 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
127 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
128 0.0000 0.0000 0.0000 0.0000 L /999999 PASS

2 2.49 101 0.0007 -0.0012 0.0007 0.0012 L /999999 PASS

102 0.0007 -0.0012 0.0007 0.0012 L /999999 PASS
103 0.0007 -0.0012 0.0007 0.0012 L /999999 PASS
104 0.0007 -0.0012 0.0007 0.0012 L /999999 PASS
105 0.0005 -0.0017 0.0005 0.0017 L /148580 PASS
106 0.0005 -0.0017 0.0005 0.0017 L /148580 PASS
107 0.0005 -0.0017 0.0005 0.0017 L /148580 PASS
108 0.0005 -0.0017 0.0005 0.0017 L /148580 PASS
109 0.2931 -0.0010 0.2931 0.0010 L / 851 PASS
110 0.2921 -0.0016 0.2921 0.0016 L / 854 PASS
111 -0.2911 -0.0017 0.2911 0.0017 L / 857 PASS
112 -0.2920 -0.0023 0.2920 0.0023 L / 854 PASS
113 0.0027 0.2696 0.0027 0.2696 L / 925 PASS
114 0.0008 0.2683 0.0008 0.2683 L / 929 PASS
115 0.0003 -0.2716 0.0003 0.2716 L / 918 PASS
116 -0.0017 -0.2729 0.0017 0.2729 L / 914 PASS
117 0.0005 -0.0008 0.0005 0.0008 L /999999 PASS
118 0.0005 -0.0008 0.0005 0.0008 L /999999 PASS
119 0.0005 -0.0008 0.0005 0.0008 L /999999 PASS
120 0.0005 -0.0008 0.0005 0.0008 L /999999 PASS
121 0.2931 -0.0002 0.2931 0.0002 L / 851 PASS
122 0.2921 -0.0008 0.2921 0.0008 L / 854 PASS
123 -0.2911 -0.0008 0.2911 0.0008 L / 857 PASS
124 -0.2920 -0.0015 0.2920 0.0015 L / 854 PASS
125 0.0027 0.2704 0.0027 0.2704 L / 922 PASS
126 0.0008 0.2691 0.0008 0.2691 L / 926 PASS
127 0.0003 -0.2708 0.0003 0.2708 L / 921 PASS
128 -0.0017 -0.2720 0.0017 0.2720 L / 917 PASS

3 5.96 101 -0.0092 -0.0343 0.0099 0.0330 L / 10503 PASS

102 -0.0092 -0.0343 0.0099 0.0330 L / 10503 PASS
103 -0.0092 -0.0343 0.0099 0.0330 L / 10503 PASS

4
 104 -0.0092 -0.0343 0.0099 0.0330 L / 10503 PASS
105 -0.0104 -0.0382 0.0109 0.0365 L / 9505 PASS
106 -0.0104 -0.0382 0.0109 0.0365 L / 9505 PASS
107 -0.0104 -0.0382 0.0109 0.0365 L / 9505 PASS
108 -0.0104 -0.0382 0.0109 0.0365 L / 9505 PASS
109 1.2104 -0.0298 0.9173 0.0288 L / 378 PASS
110 1.2139 -0.0449 0.9218 0.0433 L / 376 PASS
111 -1.2348 -0.0309 0.9437 0.0293 L / 368 PASS
112 -1.2313 -0.0460 0.9392 0.0438 L / 369 PASS
113 -0.0132 1.1654 0.0159 0.8958 L / 387 PASS
114 -0.0060 1.1345 0.0068 0.8661 L / 400 PASS
115 -0.0149 -1.2103 0.0151 0.9387 L / 369 PASS
116 -0.0076 -1.2413 0.0060 0.9684 L / 358 PASS
117 -0.0069 -0.0251 0.0075 0.0243 L / 14280 PASS
118 -0.0069 -0.0251 0.0075 0.0243 L / 14280 PASS
119 -0.0069 -0.0251 0.0075 0.0243 L / 14280 PASS
120 -0.0069 -0.0251 0.0075 0.0243 L / 14280 PASS
121 1.2139 -0.0170 0.9208 0.0168 L / 377 PASS
122 1.2174 -0.0321 0.9253 0.0313 L / 375 PASS
123 -1.2313 -0.0181 0.9402 0.0173 L / 369 PASS
124 -1.2278 -0.0332 0.9357 0.0318 L / 371 PASS
125 -0.0097 1.1782 0.0124 0.9078 L / 382 PASS
126 -0.0025 1.1473 0.0033 0.8781 L / 395 PASS
127 -0.0114 -1.1975 0.0116 0.9267 L / 374 PASS
128 -0.0041 -1.2285 0.0025 0.9564 L / 363 PASS

4 8.96 101 -0.0323 -0.1044 0.0231 0.0701 L / 4281 PASS

102 -0.0323 -0.1044 0.0231 0.0701 L / 4281 PASS
103 -0.0323 -0.1044 0.0231 0.0701 L / 4281 PASS
104 -0.0323 -0.1044 0.0231 0.0701 L / 4281 PASS
105 -0.0352 -0.1138 0.0248 0.0756 L / 3966 PASS
106 -0.0352 -0.1138 0.0248 0.0756 L / 3966 PASS
107 -0.0352 -0.1138 0.0248 0.0756 L / 3966 PASS
108 -0.0352 -0.1138 0.0248 0.0756 L / 3966 PASS
109 2.1025 -0.0956 0.8921 0.0657 L / 336 PASS
110 2.1064 -0.1147 0.8925 0.0697 L / 336 PASS
111 -2.1770 -0.1118 0.9422 0.0809 L / 318 PASS
112 -2.1731 -0.1309 0.9419 0.0849 L / 318 PASS
113 -0.0320 2.0572 0.0188 0.8917 L / 336 PASS
114 -0.0240 2.0180 0.0181 0.8835 L / 339 PASS
115 -0.0465 -2.2445 0.0316 1.0341 L / 290 PASS
116 -0.0386 -2.2837 0.0309 1.0424 L / 288 PASS
117 -0.0243 -0.0769 0.0174 0.0518 L / 5794 PASS
118 -0.0243 -0.0769 0.0174 0.0518 L / 5794 PASS
119 -0.0243 -0.0769 0.0174 0.0518 L / 5794 PASS
120 -0.0243 -0.0769 0.0174 0.0518 L / 5794 PASS
121 2.1135 -0.0592 0.8996 0.0422 L / 333 PASS
122 2.1174 -0.0783 0.9000 0.0462 L / 333 PASS
123 -2.1660 -0.0755 0.9348 0.0573 L / 321 PASS
124 -2.1622 -0.0946 0.9344 0.0614 L / 321 PASS
125 -0.0211 2.0935 0.0114 0.9153 L / 328 PASS
126 -0.0131 2.0543 0.0106 0.9071 L / 331 PASS
127 -0.0356 -2.2081 0.0242 1.0106 L / 297 PASS
128 -0.0276 -2.2473 0.0235 1.0188 L / 294 PASS

5 11.96 101 -0.0587 -0.1987 0.0265 0.0944 L / 3178 PASS

102 -0.0587 -0.1987 0.0265 0.0944 L / 3178 PASS
103 -0.0587 -0.1987 0.0265 0.0944 L / 3178 PASS

5
104 -0.0587 -0.1987 0.0265 0.0944 L / 3178 PASS
105 -0.0635 -0.2155 0.0282 0.1017 L / 2949 PASS
106 -0.0635 -0.2155 0.0282 0.1017 L / 2949 PASS
107 -0.0635 -0.2155 0.0282 0.1017 L / 2949 PASS
108 -0.0635 -0.2155 0.0282 0.1017 L / 2949 PASS
109 2.7086 -0.1818 0.6060 0.0862 L / 495 PASS
110 2.7129 -0.2151 0.6065 0.1004 L / 494 PASS
111 -2.8401 -0.2137 0.6631 0.1019 L / 452 PASS
112 -2.8357 -0.2470 0.6626 0.1160 L / 453 PASS
113 -0.0512 2.7216 0.0192 0.6644 L / 451 PASS
114 -0.0424 2.6534 0.0184 0.6354 L / 472 PASS
115 -0.0848 -3.0821 0.0383 0.8376 L / 358 PASS
116 -0.0759 -3.1503 0.0374 0.8667 L / 346 PASS
117 -0.0444 -0.1462 0.0200 0.0694 L / 4326 PASS
118 -0.0444 -0.1462 0.0200 0.0694 L / 4326 PASS
119 -0.0444 -0.1462 0.0200 0.0694 L / 4326 PASS
120 -0.0444 -0.1462 0.0200 0.0694 L / 4326 PASS
121 2.7278 -0.1136 0.6143 0.0544 L / 488 PASS
122 2.7321 -0.1469 0.6147 0.0686 L / 488 PASS
123 -2.8208 -0.1456 0.6548 0.0701 L / 458 PASS
124 -2.8165 -0.1788 0.6544 0.0843 L / 458 PASS
125 -0.0320 2.7897 0.0110 0.6962 L / 431 PASS
126 -0.0232 2.7215 0.0101 0.6671 L / 449 PASS
127 -0.0655 -3.0140 0.0300 0.8058 L / 372 PASS
128 -0.0567 -3.0822 0.0291 0.8349 L / 359 PASS

6
MOST CRITICAL BEAMS:
(P.S. I RENAMED PO THE BEAMS NAMES FROM STAAD)

BEAM NO.1 TIE BEAMS (GROUND FLOOR LEVEL) DESIGN RESULTS

==============================================================================

LEN - 2500. MM FY - 414. FC - 28. MPA, SIZE - 300. X 420. MMS

LEVEL HEIGHT BAR INFO FROM TO ANCHOR

(MM) (MM) (MM) STA END
_____________________________________________________________________

1 60. 5 - 20MM 0. 2500. YES YES

|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 170.75 KN-MET AT 2500.MM, LOAD 218|
| REQD STEEL= 1444.MM2, RHO=0.0134, RHOMX=0.0214 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 256./ 45./ 46. MMS |
| REQD. DEVELOPMENT LENGTH = 1239. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 88545.4 cm^4

REQUIRED REINF. STEEL SUMMARY :

-------------------------------
SECTION REINF STEEL(+VE/-VE) MOMENTS(+VE/-VE) LOAD(+VE/-VE)
( MM ) (SQ. MM ) (KNS-MET )

0. 1387./ 1483. 163./ 172. 217/ 230

208. 1132./ 1175. 136./ 141. 217/ 230
417. 888./ 889. 109./ 109. 209/ 230
625. 663./ 633. 83./ 79. 209/ 218
833. 442./ 392. 56./ 50. 209/ 218
1042. 221./ 164. 29./ 21. 229/ 218
1250. 71./ 17. 9./ 2. 230/ 217
1458. 284./ 240. 37./ 31. 230/ 217
1667. 499./ 474. 63./ 60. 230/ 217
1875. 719./ 723. 90./ 90. 218/ 209
2083. 957./ 996. 117./ 121. 218/ 209
2292. 1206./ 1286. 144./ 152. 218/ 209
2500. 1467./ 1597. 171./ 184. 218/ 209

___ 14J____________________ 2500X 300X 420_____________________ 251J____

| |
| |
| |
| |
| 5No20 H 60. 0.TO 2500 |
||=========================================================================||
| |
|___________________________________________________________________________|
7
 ___________ ___________ ___________ ___________ ___________
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| 5#20 | | 5#20 | | 5#20 | | 5#20 | | 5#20 |
| ooooo | | ooooo | | ooooo | | ooooo | | ooooo |
| | | | | | | | | |
|___________| |___________| |___________| |___________| |___________|

BEAM NO. 2 INTERMEDIATE TIE BEAMS (GROUND FLOOR LEVEL) AND 2ND AND 3RD FLOOR
BEAMS DESIGN RESULTS
==============================================================================
LEN - 3850. MM FY - 414. FC - 28. MPA, SIZE - 280. X 400. MMS

LEVEL HEIGHT BAR INFO FROM TO ANCHOR

(MM) (MM) (MM) STA END
_____________________________________________________________________

1 60. 4 - 20MM 0. 3850. YES YES

|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 131.80 KN-MET AT 3850.MM, LOAD 222|
| REQD STEEL= 1168.MM2, RHO=0.0123, RHOMX=0.0214 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 256./ 45./ 55. MMS |
| REQD. DEVELOPMENT LENGTH = 1043. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 64952.4 cm^4

REQUIRED REINF. STEEL SUMMARY :

-------------------------------
SECTION REINF STEEL(+VE/-VE) MOMENTS(+VE/-VE) LOAD(+VE/-VE)
( MM ) (SQ. MM ) (KNS-MET )

0. 1154./ 1636. 129./ 173. 221/ 214

321. 971./ 1252. 110./ 138. 221/ 214
642. 791./ 914. 92./ 104. 221/ 214
962. 612./ 616. 72./ 73. 213/ 234
1283. 466./ 384. 56./ 46. 213/ 222
1604. 305./ 172. 37./ 21. 213/ 222
1925. 130./ 0. 16./ 0. 213/ 0
2246. 280./ 122. 34./ 15. 214/ 221
2567. 460./ 323. 55./ 39. 214/ 221
2887. 630./ 539. 74./ 64. 214/ 221
3208. 796./ 772. 92./ 89. 234/ 221
3529. 984./ 1054. 112./ 119. 222/ 213
3850. 1187./ 1370. 132./ 149. 222/ 213

___ 253J____________________ 3849X 280X 400_____________________ 141J____

| |
| |
| |
| |
| 4No20 H 60. 0.TO 3850 |
||=========================================================================||
| |

8
|___________________________________________________________________________|
_________ _________ _________ _________ _________
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| 4#20 | | 4#20 | | 4#20 | | 4#20 | | 4#20 |
| oooo | | oooo | | oooo | | oooo | | oooo |
| | | | | | | | | |
|_________| |_________| |_________| |_________| |_________|

BEAM NO. 4 4TH FLOOR BEAMS DESIGN RESULTS

==============================================================================

LEN - 3950. MM FY - 414. FC - 28. MPA, SIZE - 250. X 400. MMS

LEVEL HEIGHT BAR INFO FROM TO ANCHOR

(MM) (MM) (MM) STA END
_____________________________________________________________________

1 58. 3 - 16MM 0. 3950. YES YES

|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 60.38 KN-MET AT 3950.MM, LOAD 222|
| REQD STEEL= 500.MM2, RHO=0.0058, RHOMX=0.0214 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 256./ 41./ 69. MMS |
| REQD. DEVELOPMENT LENGTH = 529. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 36737.4 cm^4

2 340. 3 - 20MM 0. 2500. YES NO

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 101.59 KN-MET AT 0.MM, LOAD 214|
| REQD STEEL= 884.MM2, RHO=0.0104, RHOMX=0.0214 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 256./ 45./ 67. MMS |
| REQD. DEVELOPMENT LENGTH = 851. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 51044.8 cm^4

3 340. 2 - 20MM 1400. 3950. NO YES

_ STAAD SPACE -- PAGE NO. 529

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 72.93 KN-MET AT 3950.MM, LOAD 213|
| REQD STEEL= 615.MM2, RHO=0.0072, RHOMX=0.0214 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 256./ 45./ 134. MMS |
| REQD. DEVELOPMENT LENGTH = 569. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 37439.5 cm^4

REQUIRED REINF. STEEL SUMMARY :

-------------------------------
SECTION REINF STEEL(+VE/-VE) MOMENTS(+VE/-VE) LOAD(+VE/-VE)
( MM ) (SQ. MM ) (KNS-MET )

9
 0. 432./ 897. 52./ 102. 221/ 214
329. 383./ 674. 46./ 78. 221/ 214
658. 330./ 472. 40./ 56. 221/ 214
988. 272./ 296. 33./ 36. 221/ 234
1317. 239./ 170. 29./ 21. 213/ 222
1646. 192./ 62. 24./ 8. 213/ 222
1975. 136./ 0. 17./ 0. 202/ 0
2304. 198./ 26. 24./ 3. 214/ 221
2633. 275./ 119. 33./ 15. 214/ 221
2962. 337./ 221. 41./ 27. 214/ 221
3292. 388./ 331. 46./ 40. 234/ 221
3621. 440./ 462. 52./ 55. 222/ 213
3950. 510./ 624. 60./ 73. 222/ 213
_

B E A M N O. 548 D E S I G N R E S U L T S - SHEAR

_
AT START SUPPORT - Vu= 31.43 KNS Vc= 77.26 KNS Vs= 0.00 KNS
Tu= 0.12 KN-MET Tc= 2.7 KN-MET Ts= 0.0 KN-MET LOAD 201
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 171. MM C/C FOR 1635. MM

AT END SUPPORT - Vu= 45.84 KNS Vc= 74.25 KNS Vs= 0.00 KNS
Tu= 0.35 KN-MET Tc= 2.6 KN-MET Ts= 0.0 KN-MET LOAD 212
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 171. MM C/C FOR 1635. MM

___ 255J____________________ 3950X 250X 400_____________________ 155J____

| |
||=========================================================================||
| 3No20 H 340.| 0.TO 2500|2No20 H|340.1400.TO|3950 | | | | | | |
| 11*10c/c171 | | | | | | | | | | | | 11*10c/c171 | |
| 3No16 H |58.| 0.TO 3950| | | | | | | | | | | | | |
||=========================================================================||
| |
|___________________________________________________________________________|
_________ _________ _________ _________ _________
| | | | | | | | | |
| ooo | | ooo | | ooo | | oo | | oo |
| 3#20 | | 3#20 | | 2#20 | | 2#20 | | 2#20 |
| | | | | | | | | |
| 3#16 | | 3#16 | | 3#16 | | 3#16 | | 3#16 |
| ooo | | ooo | | ooo | | ooo | | ooo |
| | | | | | | | | |
|_________| |_________| |_________| |_________| |_________|

BEAM NO.5 4TH FLOOR INTERMEDIATE AND ROOF OVERHANGING BEAMS DESIGN RESULTS
==============================================================================

LEN - 3175. MM FY - 276. FC - 21. MPA, SIZE - 225. X 350. MMS

LEVEL HEIGHT BAR INFO FROM TO ANCHOR

(MM) (MM) (MM) STA END

10
 _____________________________________________________________________

_
1 60. 3 - 20MM 0. 2545. YES NO
_ STAAD SPACE -- PAGE NO. 502

|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 58.45 KN-MET AT 0.MM, LOAD 209|
| REQD STEEL= 909.MM2, RHO=0.0139, RHOMX=0.0282 RHOMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 446./ 45./ 54. MMS |
| REQD. DEVELOPMENT LENGTH = 800. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 38009.4 cm^4

REQUIRED REINF. STEEL SUMMARY :

-------------------------------
SECTION REINF STEEL(+VE/-VE) MOMENTS(+VE/-VE) LOAD(+VE/-VE)
( MM ) (SQ. MM ) (KNS-MET )

0. 927./ 0. 58./ 0. 209/ 0

265. 827./ 0. 53./ 0. 209/ 0
529. 720./ 0. 47./ 0. 209/ 0
794. 603./ 0. 40./ 0. 209/ 0
1058. 469./ 0. 31./ 0. 209/ 0
1323. 328./ 0. 22./ 0. 202/ 0
1588. 163./ 0. 11./ 0. 202/ 0
1852. 19./ 55. 1./ 4. 218/ 209
2117. 0./ 279. 0./ 19. 0/ 209
2381. 0./ 540. 0./ 36. 0/ 209
2646. 0./ 837. 0./ 53. 0/ 209
2910. 0./ 1175. 0./ 72. 0/ 209
3175. 0./ 1563. 0./ 90. 0/ 209

___ 246J____________________ 3175X 225X 350_____________________ 77J____

| |
| |
| |
| |
| 3No20 H 60. 0.TO 2545 |
||==========================================================================
|
| |
|___________________________________________________________________________|
_________ _________ _________ _________ _________
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| 3#20 | | 3#20 | | 3#20 | | 3#20 | | 3#20
| ooo | | ooo | | ooo | | ooo | | ooo
|
| | | | | | | | | |
|_________| |_________| |_________| |_________| |_________|

BEAM NO.6 PARAPET AND OVERHANGING BEAMS FROM 2ND TO 3RD FLOOR DESIGN RESULTS

11
==============================================================================

LEN - 2685. MM FY - 276. FC - 21. MPA, SIZE - 200. X 400. MMS

LEVEL HEIGHT BAR INFO FROM TO ANCHOR

(MM) (MM) (MM) STA END
_____________________________________________________________________

1 58. 2 - 16MM 0. 2685. YES YES

|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 25.77 KN-MET AT 2685.MM, LOAD 211|
| REQD STEEL= 342.MM2, RHO=0.0050, RHOMX=0.0282 RHOMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 446./ 41./ 88. MMS |
| REQD. DEVELOPMENT LENGTH = 348. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 28336.8 cm^4

2 342. 3 - 16MM 0. 1940. YES NO

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 46.79 KN-MET AT 0.MM, LOAD 211|
| REQD STEEL= 590.MM2, RHO=0.0086, RHOMX=0.0282 RHOMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 446./ 41./ 44. MMS |
| REQD. DEVELOPMENT LENGTH = 635. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 38786.4 cm^4

3 342. 2 - 16MM 1225. 2685. NO YES

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 24.09 KN-MET AT 2685.MM, LOAD 216|
| REQD STEEL= 342.MM2, RHO=0.0050, RHOMX=0.0282 RHOMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 446./ 41./ 88. MMS |
| REQD. DEVELOPMENT LENGTH = 348. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 28336.8 cm^4

REQUIRED REINF. STEEL SUMMARY :

-------------------------------
SECTION REINF STEEL(+VE/-VE) MOMENTS(+VE/-VE) LOAD(+VE/-VE)
( MM ) (SQ. MM ) (KNS-MET )

0. 268./ 603. 22./ 47. 216/ 211

224. 239./ 470. 19./ 37. 216/ 211
448. 208./ 347. 17./ 28. 216/ 211
671. 174./ 236. 14./ 19. 216/ 211
895. 137./ 138. 11./ 11. 208/ 231
1119. 114./ 69. 9./ 6. 208/ 219
1342. 81./ 5. 7./ 0. 208/ 219
1566. 93./ 0. 8./ 0. 211/ 0
1790. 151./ 51. 12./ 4. 211/ 216
2014. 202./ 108. 16./ 9. 211/ 216
2238. 246./ 169. 20./ 14. 211/ 216
2461. 285./ 232. 23./ 19. 211/ 216
2685. 321./ 299. 26./ 24. 211/ 216

12
 B E A M N O. 360 D E S I G N R E S U L T S - SHEAR

AT START SUPPORT - Vu= 3.98 KNS Vc= 36.81 KNS Vs= 0.00 KNS
Tu= 2.14 KN-MET Tc= 0.9 KN-MET Ts= 2.8 KN-MET LOAD 209
STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 106. MM C/C FOR 1002. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 1.46
SQ.CM.

AT END SUPPORT - Vu= 23.43 KNS Vc= 36.81 KNS Vs= 0.00 KNS
Tu= 2.14 KN-MET Tc= 0.9 KN-MET Ts= 2.8 KN-MET LOAD 209
STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 106. MM C/C FOR 1002. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 1.46
SQ.CM.

___ 154J____________________ 2684X 200X 400_____________________ 188J____

| |
||=========================================================================||
| 3No16 H 342.| 0.TO 1940| | |2No16 H|342.1225.TO|2685 | | | | |
| 11*10c/c106 | | | | | | | | | | | | 11*10c/c106 | |
| 2No16 H |58.| 0.TO 2685| | | | | | | | | | | | | |
||=========================================================================||
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______
| | | | | | | | | |
| ooo | | ooo | | ooo | | oo | | oo |
| 3#16 | | 3#16 | | 2#16 | | 2#16 | | 2#16 |
| | | | | | | | | |
| 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 |
| oo | | oo | | oo | | oo | | oo |
| | | | | | | | | |
|_______| |_______| |_______| |_______| |_______|

BEAM NO.7 2ND TO 3RD FLOOR INTERMEDIATE BEAMS, 4TH FLOOR PARAPET BEAMS AND MAIN
ROOF BEAMS DESIGN RESULTS
==============================================================================

LEN - 2600. MM FY - 414. FC - 28. MPA, SIZE - 250. X 350. MMS

LEVEL HEIGHT BAR INFO FROM TO ANCHOR

(MM) (MM) (MM) STA END
_____________________________________________________________________

_
1 58. 3 - 16MM 0. 2600. YES YES
|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 47.60 KN-MET AT 2600.MM, LOAD 218|
| REQD STEEL= 464.MM2, RHO=0.0064, RHOMX=0.0214 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 256./ 41./ 69. MMS |
| REQD. DEVELOPMENT LENGTH = 529. MMS |
|----------------------------------------------------------------|
13
 Cracked Moment of Inertia Iz at above location = 25874.9 cm^4

2 290. 2 - 20MM 0. 1653. YES NO

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 61.55 KN-MET AT 0.MM, LOAD 210|
| REQD STEEL= 616.MM2, RHO=0.0085, RHOMX=0.0214 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 256./ 45./ 134. MMS |
| REQD. DEVELOPMENT LENGTH = 569. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 26290.8 cm^4

3 290. 2 - 20MM 839. 2600. NO YES

_ STAAD SPACE -- PAGE NO. 531

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 61.31 KN-MET AT 2600.MM, LOAD 209|
| REQD STEEL= 614.MM2, RHO=0.0085, RHOMX=0.0214 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 256./ 45./ 134. MMS |
| REQD. DEVELOPMENT LENGTH = 569. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 26290.8 cm^4

REQUIRED REINF. STEEL SUMMARY :

-------------------------------
SECTION REINF STEEL(+VE/-VE) MOMENTS(+VE/-VE) LOAD(+VE/-VE)
( MM ) (SQ. MM ) (KNS-MET )

0. 417./ 627. 42./ 62. 217/ 210

217. 356./ 473. 36./ 47. 217/ 210
433. 292./ 334. 30./ 34. 217/ 210
650. 235./ 217. 24./ 22. 209/ 218
867. 184./ 124. 19./ 13. 209/ 218
1083. 122./ 37. 13./ 4. 209/ 218
1300. 85./ 0. 9./ 0. 210/ 0
1517. 159./ 72. 17./ 8. 210/ 217
1733. 224./ 159. 23./ 17. 210/ 217
1950. 281./ 251. 29./ 26. 210/ 217
2167. 338./ 358. 34./ 36. 218/ 209
2383. 407./ 487. 41./ 49. 218/ 209
2600. 475./ 625. 48./ 61. 218/ 209
_

B E A M N O. 550 D E S I G N R E S U L T S - SHEAR

AT START SUPPORT - Vu= 28.64 KNS Vc= 71.11 KNS Vs= 0.00 KNS
Tu= 0.21 KN-MET Tc= 2.1 KN-MET Ts= 0.0 KN-MET LOAD 202
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 146. MM C/C FOR 1010. MM

AT END SUPPORT - Vu= 54.88 KNS Vc= 63.68 KNS Vs= 9.49 KNS
Tu= 0.03 KN-MET Tc= 2.2 KN-MET Ts= 0.0 KN-MET LOAD 208
NO STIRRUPS ARE REQUIRED FOR TORSION.

14
REINFORCEMENT IS REQUIRED FOR SHEAR.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 146. MM C/C FOR 1010. MM

___ 35J____________________ 2599X 250X 350_____________________ 255J____

| |
||=========================================================================||
| 2No20 H 290.| 0.TO 1653No20 H|290. |839.TO 2600 | | | | ||
| 8*10c/c146 | | | | | | | | | | | | 8*10c/c146 ||
| 3No16 H |58.| 0.TO 2600| | | | | | | | | | | | ||
||=========================================================================||
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______
| | | | | | | | | |
| oo | | oo | | oo | | oo | | oo |
| 2#20 | | 2#20 | | 2#20 | | 2#20 | | 2#20 |
| | | | | | | | | |
| 3#16 | | 3#16 | | 3#16 | | 3#16 | | 3#16 |
| ooo | | ooo | | ooo | | ooo | | ooo |
| | | | | | | | | |
|_______| |_______| |_______| |_______| |_______|

15
MOST CRITICAL COLUMNS:

COLUMN NO.1 FOUNDATION TO GROUND FLOOR LEVEL DESIGN RESULTS

==============================================================================

FY - 413.7 FC - 27.6 MPA, SQRE SIZE - 550.0 X 550.0 MMS, TIED

AREA OF STEEL REQUIRED = 3893.2 SQ. MM

BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI

----------------------------------------------------------

20 - 16 MM 1.329 230 STA 0.650

(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 10 SPACING 256.00 MM

COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
8660.54 6928.43 3280.65 736.18 224.4
M0 P-tens. Des.Pn Des.Mn e/h
389.53 -1663.55 91.37 368.84 1.61853
--------------------------------------------------------

COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
8660.54 6928.43 3280.65 736.18 224.4
M0 P-tens. Des.Pn Des.Mn e/h
389.53 -1663.55 91.37 52.63 0.23095
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 6395.47 461.68 3197.74 735.24
P0 |* 5862.52 535.29 2664.78 722.86
| * 5329.56 596.61 2131.82 692.60
Pn,max|__* 4796.60 644.93 1598.87 646.05
| * 4263.65 683.70 1065.91 578.73
Pn | * 3730.69 714.61 532.96 490.33
NOMINAL| * Pn Mn Pn Mn (@ Y )
AXIAL| * 6395.47 461.68 3197.74 735.24
COMPRESSION| * 5862.52 535.29 2664.78 722.86
Pb|-------*Mb 5329.56 596.61 2131.82 692.60
| * 4796.60 644.93 1598.87 646.05
___________|____*_______ 4263.65 683.70 1065.91 578.73
| * M0 Mn, 3730.69 714.61 532.96 490.33
| * BENDING
P-tens|* MOMENT
|

COLUMN NO.2 SECOND TO THIRD FLOOR LEVEL DESIGN RESULTS

==============================================================================

FY - 413.7 FC - 27.6 MPA, SQRE SIZE - 450.0 X 450.0 MMS, TIED

AREA OF STEEL REQUIRED = 2152.6 SQ. MM

BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI

16
 ----------------------------------------------------------

12 - 16 MM 1.191 218 STA 0.650

(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 10 SPACING 256.00 MM

COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
5688.61 4550.89 2131.24 385.23 180.8
M0 P-tens. Des.Pn Des.Mn e/h
188.64 -998.13 9.39 160.58 5.70314
--------------------------------------------------------

COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
5688.61 4550.89 2131.24 385.23 180.8
M0 P-tens. Des.Pn Des.Mn e/h
188.64 -998.13 9.39 22.09 0.78469
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 4200.82 245.27 2100.41 384.71
P0 |* 3850.75 283.35 1750.34 375.06
| * 3500.68 315.05 1400.27 359.70
Pn,max|__* 3150.61 340.19 1050.20 330.81
| * 2800.55 359.72 700.14 291.93
Pn | * 2450.48 374.54 350.07 246.45
NOMINAL| * Pn Mn Pn Mn (@ Y )
AXIAL| * 4200.82 245.27 2100.41 384.71
COMPRESSION| * 3850.75 283.35 1750.34 375.06
Pb|-------*Mb 3500.68 315.05 1400.27 359.70
| * 3150.61 340.19 1050.20 330.81
___________|____*_______ 2800.55 359.72 700.14 291.93
| * M0 Mn, 2450.48 374.54 350.07 246.45
| * BENDING
P-tens|* MOMENT
|

COLUMN NO.3 FOURTH FLOOR LEVEL DESIGN RESULTS

==============================================================================

FY - 413.7 FC - 27.6 MPA, SQRE SIZE - 350.0 X 350.0 MMS, TIED

ONLY MINIMUM STEEL IS REQUIRED.
AREA OF STEEL REQUIRED = 1225.0 SQ. MM

BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI

----------------------------------------------------------

4 - 20 MM 1.026 201 END 0.650

(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 10 SPACING 320.00 MM

COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
17
 3362.06 2689.65 1223.52 186.40 152.3
M0 P-tens. Des.Pn Des.Mn e/h
74.61 -519.85 31.82 5.86 0.06134
--------------------------------------------------------

COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
3362.06 2689.65 1223.52 186.40 152.3
M0 P-tens. Des.Pn Des.Mn e/h
74.61 -519.85 31.82 7.36 0.07707
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 2482.75 116.88 1241.38 185.92
P0 |* 2275.86 135.22 1034.48 179.09
| * 2068.96 150.49 827.58 165.50
Pn,max|__* 1862.07 162.70 620.69 147.53
| * 1655.17 172.31 413.79 125.77
Pn | * 1448.27 179.85 206.90 101.10
NOMINAL| * Pn Mn Pn Mn (@ Y )
AXIAL| * 2482.75 116.88 1241.38 185.92
COMPRESSION| * 2275.86 135.22 1034.48 179.09
Pb|-------*Mb 2068.96 150.49 827.58 165.50
| * 1862.07 162.70 620.69 147.53
___________|____*_______ 1655.17 172.31 413.79 125.77
| * M0 Mn, 1448.27 179.85 206.90 101.10
| * BENDING
P-tens|* MOMENT
|

*********** END OF THE STAAD.Pro RUN ***********

FOOTING DESIGN (SERVICEABILITY METHOD!)

Assumed Soil Bearing Capacity = 180 kPa

18
FOOTING 1
Reactions:
DL = 516.975 kN
LL = 97.809 kN
Total Load = 614.784 kN

Area = Total Load / SBC

Area = 3.415 m2
Size (Square) = 1.848 m x 1.848 m ~ 1.9 m x 1.9 m (APPROXIMATED!)

Thickness = 0.08 x 614.784 / (1.9 m x 1.9 m x 23.6)

Thickness = 0.577 m ~ 600 mm
REINFORCEMENT (Grade 40 - 16 mm Diameter):
Mz = 158.666 kN-m
MINIMUM REINFORCEMENT [ As = (1.4/fy) Ag ]
As= (1.4/276)(1900*600)
As = 5,782.609 m2 (yields 29 pcs O.C.)
BOTTOM - 29 pcs on centers
TOP - 29 pcs on centers

FOOTING 2
Reactions:
DL = 571.149 kN
LL = 105.018 kN
Total Load = 676.167 kN

Area = Total Load / SBC

Area = 3.7565 m2
Size (Square) = 1.9382 m x 1.9382 m ~ 2 m x 2 m

Thickness = 0.08 x Total Load / (Area x 23.6)

Thickness = .573 m ~ 600 mm

REINFORCEMENT (16 mm Diameter):

BOTTOM - 31 pcs on centers
TOP - 31 pcs on centers

FOOTING 3
Reactions:
DL = 552.805 kN
LL = 90.831 kN
Total Load = 643.636 kN

Area = Total Load / SBC

Area = 3.5758 m2
Size (Square) = 1.891 m x 1.891 m ~ 1.9 m x 1.9 m

Thickness = 0.08 x Total Load / (Area x 23.6)

Thickness = .6044 m ~ 650 mm

REINFORCEMENT (16 mm Diameter):

BOTTOM - 32 pcs on centers
19
 TOP - 32 pcs on centers

FOOTING 4
Reactions:
DL = 572.28 kN
LL = 105.184 kN
Total Load = 677.464 kN

Area = Total Load / SBC

Area = 3.7637 m2
Size (Square) = 1.94 m x 1.94 m ~ 2 m x 2 m

Thickness = 0.08 x Total Load / (Area x 23.6)

Thickness = .5741 m~ 600 mm

REINFORCEMENT (16 mm Diameter):

BOTTOM - 31 pcs on centers
TOP - 31 pcs on centers

FOOTING 5
Reactions:
DL = 552.984 kN
LL = 90.812 kN
Total Load = 643.796 kN

Area = Total Load / SBC

Area = 3.5766 m2
Size (Square) = 1.8912 m x 1.8912m ~ 1.9 m x 1.9 m

Thickness = 0.08 x Total Load / (Area x 23.6)

Thickness = .6045 m ~ 650 mm

REINFORCEMENT (16 mm Diameter):

BOTTOM - 32 pcs on centers
TOP - 32 pcs on centers

FOOTING 6
Reactions:
DL = 574.498 kN
LL = 105.491 kN
Total Load = 679.989 kN

Area = Total Load / SBC

Area = 3.7777 m2
Size (Square) = 1.9436 m x 1.9436 m ~ 2 m x 2 m

Thickness = 0.08 x Total Load / (Area x 23.6)

Thickness = .5763 m ~ 600 mm

REINFORCEMENT (16 mm Diameter):

BOTTOM - 31 pcs on centers
TOP - 31 pcs on centers

20
FOOTING 7
Reactions:
DL = 531.688 kN
LL = 89.366 kN
Total Load = 621.054 kN

Area = Total Load / SBC

Area = 3.4503 m2
Size (Square) = 1.8575 m x 1.8575 m ~ 1.9 m x 1.9 m

Thickness = 0.08 x Total Load / (Area x 23.6)

Thickness = .5832 m ~ 600 mm

REINFORCEMENT (16 mm Diameter):

BOTTOM - 29 pcs on centers
TOP - 29 pcs on centers
FOOTING 8
Reactions:
DL = 327.029 kN
LL = 44.098 kN
Total Load = 371.127 kN

Area = Total Load / SBC

Area = 2.0618 m2
Size (Square) = 1.4359 m x 1.4359 m ~ 1.5 m x 1.5 m

Thickness = 0.08 x Total Load / (Area x 23.6)

Thickness = .5591 m ~ 600 mm

REINFORCEMENT (16 mm Diameter):

BOTTOM - 23 pcs on centers
TOP - 23 pcs on centers

FOOTING 9
Reactions:
DL = 656.414 kN
LL = 123.738 kN
Total Load = 780.152 kN

Area = Total Load / SBC

Area = 4.3342 m2
Size (Square) = 2.0819 m x 2.0819 m ~ 2.1 m x 2.1 m

Thickness = 0.08 x Total Load / (Area x 23.6)

Thickness = .5997 m ~ 600 mm

REINFORCEMENT (16 mm Diameter):

BOTTOM - 32 pcs on centers
TOP - 32 pcs on centers

FOOTING 10
Reactions:
21
DL = 783.186 kN
LL = 124.047 kN
Total Load = 907.233 kN

Area = Total Load / SBC

Area = 5.0402 m2
Size (Square) = 2.2450 m x 2.2450 m ~ 2.3 m x 2.3 m

Thickness = 0.08 x Total Load / (Area x 23.6)

Thickness = .5814 m ~ 600 mm

REINFORCEMENT (16 mm Diameter):

BOTTOM - 35 pcs on centers
TOP - 35 pcs on centers

FOOTING 11
Reactions:
DL = 783.642 kN
LL = 124.207 kN
Total Load = 907.848 kN

Area = Total Load / SBC

Area = 5.0436 m2
Size (Square) = 2.2458 m x 2.2458 m ~ 2.3 m x 2.3 m

Thickness = 0.08 x Total Load / (Area x 23.6)

Thickness = .5817 m ~ 600 mm

REINFORCEMENT (16 mm Diameter):

BOTTOM - 35 pcs on centers
TOP - 35 pcs on centers

FOOTING 12
Reactions:
DL = 642.442 kN
LL = 128.303 kN
Total Load = 770.745kN

Area = Total Load / SBC

Area = 4.2819 m2
Size (Square) = 2.0693 m x 2.0693 m ~ 2.1 m x 2.1 m

Thickness = 0.08 x Total Load / (Area x 23.6)

Thickness = .5924 m ~ 600 mm

REINFORCEMENT (16 mm Diameter):

BOTTOM - 32 pcs on centers
TOP - 32 pcs on centers

FOOTING 13
Reactions:
DL = 253.08 kN
LL = 54.748 kN
22
Total Load = 307.828 kN

Area = Total Load / SBC

Area =1.7102 m2
Size (Square) = 1.3077 m x 1.3077 m ~ 1.31 m x 1.31 m

Thickness = 0.08 x Total Load / (Area x 23.6)

Thickness = .6081 m ~ 650 mm

REINFORCEMENT (16 mm Diameter):

BOTTOM - 22 pcs on centers
TOP - 22 pcs on centers

FOOTING 14
Reactions:
DL = 462.695 kN
LL = 84.61 kN
Total Load = 547.305 kN

Area = Total Load / SBC

Area = 3.0406 m2
Size (Square) = 1.7437 m x 1.7437 m ~ 1.75 m x 1.75 m

Thickness = 0.08 x Total Load / (Area x 23.6)

Thickness = .6058 m ~ 650 mm

REINFORCEMENT (16 mm Diameter):

BOTTOM - 29 pcs on centers
TOP - 29 pcs on centers

FOOTING 15
Reactions:
DL = 490.698 kN
LL = 82.122 kN
Total Load = 572.82 kN

Area = Total Load / SBC

Area = 3.1823 m2
Size (Square) = 1.7839 m x 1.7839 m ~ 1.8 m x 1.8 m

Thickness = 0.08 x Total Load / (Area x 23.6)

Thickness = .5993 m ~ 600 mm

REINFORCEMENT (16 mm Diameter):

BOTTOM - 28 pcs on centers
TOP - 28 pcs on centers

FOOTING 16
Reactions:
DL =500.753 kN
LL = 76.388 kN
Total Load =577.141 kN
23
Area = Total Load / SBC
Area = 3.2063 m2
Size (Square) = 1.7906 m x 1.7906 m ~ 1.8 m x 1.8 m

Thickness = 0.08 x Total Load / (Area x 23.6)

Thickness = 0.6038 m ~ 650 mm

REINFORCEMENT (16 mm Diameter):

BOTTOM - 30 pcs on centers
TOP - 30 pcs on centers

FOOTING 17
Reactions:
DL =490.698 kN
LL = 82.122 kN
Total Load = 572.82 kN

Area = Total Load / SBC

Area = 3.1823 m2
Size (Square) = 1.7839 m x 1.7839 m ~1.8 m x 1.8 m

Thickness = 0.08 x Total Load / (Area x 23.6)

Thickness = .5993 m ~ 600 mm

REINFORCEMENT (16 mm Diameter):

BOTTOM - 28 pcs on centers
TOP - 28 pcs on centers

FOOTING 18
Reactions:
DL = 500.2 kN
LL = 75.836 kN
Total Load = 576.036 kN

Area = Total Load / SBC

Area = 3.2002 m2
Size (Square) = 1.7889 m x 1.7889 m ~ 1.8 m x 1.8 m

Thickness = 0.08 x Total Load / (Area x 23.6)

Thickness = 0.6027 m ~ 650 mm

REINFORCEMENT (16 mm Diameter):

BOTTOM - 30 pcs on centers
TOP - 30 pcs on centers

FOOTING 19
Reactions:
DL = 491.446 kN
LL = 82.651 kN
Total Load = 574.097 kN

Area = Total Load / SBC

24
Area = 3.1894 m2
Size (Square) = 1.7859 m x 1.7859 m ~ 1.8 m x 1.8 m

Thickness = 0.08 x Total Load / (Area x 23.6)

Thickness = .6006 m ~ 650 mm

REINFORCEMENT (16 mm Diameter):

BOTTOM - 30 pcs on centers
TOP - 30 pcs on centers

FOOTING 20
Reactions:
DL = 403.525 kN
LL = 76.276 kN
Total Load = 479.801 kN

Area = Total Load / SBC

Area = 2.6656 m2
Size (Square) = 1.6327 m x 1.6327 m ~ 1.65 m x 1.65 m

Thickness = 0.08 x Total Load / (Area x 23.6)

Thickness = .5974 m ~ 600 mm

REINFORCEMENT (16 mm Diameter):

BOTTOM - 25 pcs on centers
TOP - 25 pcs on centers

FOOTING 21
Reactions:
DL = 163.733 kN
LL = 34.293 kN
Total Load = 198.026 kN

Area = Total Load / SBC

Area = 1.1001 m2
Size (Square) = 1.0489 m x 1.0489 m ~ 1.1 m x 1.1 m

Thickness = 0.08 x Total Load / (Area x 23.6)

Thickness = .5548 m ~ 600 mm

REINFORCEMENT (16 mm Diameter):

BOTTOM - 17 pcs on centers
TOP - 17 pcs on centers

FOOTING 22
Reactions:
DL = 228.745 kN
LL = 39.389 kN
Total Load = 268.134 kN

Area = Total Load / SBC

Area = 1.4896 m2
Size (Square) = 1.2205 m x 1.2205 m ~ 1.3 m x 1.3 m
25
Thickness = 0.08 x Total Load / (Area x 23.6)
Thickness = .5378 m ~ 550 mm

REINFORCEMENT (16 mm Diameter):

BOTTOM - 19 pcs on centers
TOP - 19 pcs on centers

FOOTING 23
Reactions:
DL = 298.2 kN
LL = 58.906 kN
Total Load = 357.106 kN

Area = Total Load / SBC

Area = 1.9839 m2
Size (Square) = 1.4085 m x 1.4085 m ~ 1.41 m x 1.41 m

Thickness = 0.08 x Total Load / (Area x 23.6)

Thickness = .6089 m ~ 650 mm

REINFORCEMENT (16 mm Diameter):

BOTTOM - 24 pcs on centers
TOP - 24 pcs on centers

FOOTING 24
Reactions:
DL = 299.358 kN
LL = 59.669 kN
Total Load = 359.027 kN

Area = Total Load / SBC

Area = 1.9946 m2
Size (Square) = 1.4123 m x 1.4123 m ~ 1.45 m x 1.45 m

Thickness = 0.08 x Total Load / (Area x 23.6)

Thickness = .5789 m ~ 600 mm

REINFORCEMENT (16 mm Diameter):

BOTTOM - 22 pcs on centers
TOP - 22 pcs on centers

FOOTING 25
Reactions:
DL = 205.861 kN
LL = 35.833 kN
Total Load = 241.694 kN

Area = Total Load / SBC

Area =1.3427 m2
Size (Square) = 1.1588 m x 1.1588 m ~ 1.2 m x 1.2 m

Thickness = 0.08 x Total Load / (Area x 23.6)

26
 Thickness = .5690 m ~ 600 mm

REINFORCEMENT (16 mm Diameter):

BOTTOM - 19 pcs on centers
TOP - 19 pcs on centers

FOOTING LAYOUT

27
 Where:
C1 = 550 mm x 550 mm
F1 = 1.9 m x 1.9 m F8 = 1.75 m x 1.75 m
F2 = 2.0 m x 2.0 m F9 = 1.65 m x 1.65 m

F3 = 2.1 m x 2.1 m F10 = 1.10 m x 1.10 m

F4 = 2.3 m x 2.3 m F11 = 1.30 m x 1.30 m
F5 = 1.8 m x 1.8 m F12 = 1.41 m x 1.41 m
F6 = 1.5 m x 1.5 m F13 = 1.45 m x 1.45 m
F7 = 1.31 m x 1.31 m F14 = 1.20 m x 1.20 m

**SNAPSHOT OF “Beam
Stress” from Post-process**

28