Teddy Bear Rattle
No. 1001-191-4450
Materialer: Abbreviations:
- Boheme Velvet - Fine from Go ch: chain
Handmade st: stitch
- Crochet Hook 3.0mm sc: single crochet
- Safety Eyes 8 mm
- Safety Nose 9 mm
- Rattle Ball 24 mm Yarn Requirement: Approx. 10g
- Wooden Ring 2 ½” (68 mm)
- Fiber Fill
Buy the yarn and materials here:
http://shop.hobbii.com/teddy-bear-rattle
Hobbii.com - Copyright © 2019 - All rights reserved. Page 1
Head:
1. Starting with a magic ring, work 6 sc into the ring (6)
2. Work 2 sc in each st. (12)
3. Work *1 sc, 2sc in the next st* repeat *-* to the end of the rnd. (18)
4. Work *1 sc in the next 2 sts, 2sc in the next st* repeat *-* to the end of the rnd. (24)
5. Work *1 sc in the next 3 sts, 2sc in the next st* repeat *-* to the end of the rnd. (30)
6. Work 1 sc in each st. (30)
7. Work *1 sc in the next 4 sts, 2sc in the next st* repeat *-* to the end of the rnd. (36)
8. Work *1 sc in the next 5 sts, 2sc in the next st* repeat *-* to the end of the rnd. (42)
9. Work 1 sc in each st. (42)
10. Work 1 sc in each st. (42)
11. Work 1 sc in each st. (42) – Attach the nose between rnds 2 & 3 and the eyes between rnds 6 & 7
with 3-4 sts between them.
12. Work *1 sc in the next 5 sts, sc2tog* repeat *-* to the end of the rnd. (36)
13. Work 1 sc in each st. (36)
14. Work *1 sc in the next 4 sts, sc2tog* repeat *-* to the end of the rnd. (30) Place the rattle ball and
fiber fill into the head at this point and continue to fill as you close the hole.
15. Work *1 sc in the next 3 sts, sc2tog* repeat *-* to the end of the rnd. (24)
16. Work *1 sc in the next 2 sts, sc2tog* repeat *-* to the end of the rnd. (18)
17. Work *1 sc in the next st, sc2tog* repeat *-* to the end of the rnd. (12)
18. Work *sc2tog* repeat *-* to the end of the rnd. (6)
Sew the hole closed and weave in the ends.
Shaping:
1. Now you need to add depth under the eyes to 2. Using a darning needle, pull the yarn through
give the bear’s face the correct shape.. the head and out by the right side of the eye
as shown here.
Hobbii.com - Copyright © 2019 - All rights reserved. Page 2
3. Insert the needle on the other side of the eye 4. Repeat for the other eye. Pull the yarn
and through the head. Pull gently. through the head and out by the right side of
the eye as shown here.
5. Insert the needle on the other side of the eye 6. Pull gently on both ends of the yarn until you
and through the head. have the desired shape for both eyes. Weave
in the ends.
Ears: - Make 2
1. Start with a magic ring and work 6 sc into the ring. (6)
2. Work 2 sc in each st. (12)
3. Work *1 sc, 2sc in the next st* repeat *-* to the end of the rnd. (18)
4. Work *1 sc in the next 2 sts, 2sc in the next st* repeat *-* to the end of the rnd. (24)
Fold the ear so it is flat and crochet closed using a row of sc. Cut the yarn and weave in the ends
Sew the ears to the head as shown below.
Hobbii.com - Copyright © 2019 - All rights reserved. Page 3
Attaching the bear to the wooden ring:
1. Ch 13. In the 2nd ch from the hook, work 1 sc. Work sc in each st to the end of the row (12)
2. -8. Ch 1 and turn. Work sc in each st to the end of the row (12)
Cut the yarn, leaving a long tail for sewing. Fold the piece around the wooden ring and sew the edges
together.
Hobbii.com - Copyright © 2019 - All rights reserved. Page 4
Now sew the bear to the piece on the ring. Now your teddy bear rattle is ready! 😊
Enjoy! ☺
Best Wishes, Hobbii
Hobbii.com - Copyright © 2019 - All rights reserved. Page 5
