-------------------------

| FABRICATION MATERIALS | N

THIS DOCUM ENT W ITHOUT THE W RITTEN CONSENT OF ITS OW NER.

2
------------------------- 90°
PT N.S. WEIGHT K
NO COMPONENT DESCRIPTION (INS) ITEM CODE SM QTY (Kg.)

PIPE
----
1 K NPS:2-THK:3.91MM-PIPE-ASTM A106 2 AA005 3.4 M 9.9
GR.B - SMLS

FITTINGS 1
-------- >
<1
 2 K (1)-NPS:2-THK:3.91MM-90LONG 2 FB001 2
RADIUS ELBOW - ASME-B16.9-ASTM 60
10
A234 WPB - SMLS

2
FLANGES
90°
-------
EL +12841
3 K (1)-NPS:2-THK:5.54MM-WN FLANGE - 2 BB218 1 4.1
CLASS: K K
ASME-B16.5-CL300-RF125
11G
µIN.RA-ASTM A105
146
4 K (1)-NPS:2-THK:3.91MM-WN FLANGE - 2 BB005 1 2.7
CLASS:
ASME-B16.5-CL150-RF125
13S
µIN.RA-ASTM A105
--------
2"NPD
TOTAL FABRICATION WEIGHT 18.1
-------- 215 F3 G5 B7
K

NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM

---------------------- 9
| ERECTION MATERIALS | G5 B7 STEM WEST
CONN TO
---------------------- K
21-E-303/ V2
PT N.S. WEIGHT

2560
2"-21-TL3046C-13S-V(PP)
2" RF CL300
NO COMPONENT DESCRIPTION (INS) ITEM CODE SM QTY (Kg.)
E 466400
N 348145
GASKETS
K
EL +12475
-------
5 NPS:2-CL300-RF- SP.WOUND GSKT-WITH 2 TT055 2 -
OUT.& INN.RINGS - TB GUA
5365-316L SS+GRAPH 99.8% - C.S.
OUT.RING
6 NPS:2-CL150-RF- SP.WOUND GSKT-WITH 2 TT005 2 -
OUT.& INN.RINGS - TB GUA
5365-316L SS+GRAPH 99.8% - C.S.
OUT.RING

BOLTS

1
-----

2"NPD
7 5/8INCH-L=90MM-ST.BOLT+2 NUTS - 5/8 WPT88 16 2.3

<2>
ANSI THDD - TB BUL 5368-ASTM A193
B7 + ASTM A194 GR.2H-GA-E-60024,
90.0MM BOLT LENGTH
8 5/8INCH-L=85MM-ST.BOLT+2 NUTS - 5/8 WPT85 8 1.1
F-02 (WELD TO PIPE ONLY ON TOP)
ANSI THDD - TB BUL 5368-ASTM A193
B7 + ASTM A194 GR.2H-GA-E-60024, G-28
85.0MM BOLT LENGTH P-38B-1200-350
(SUITE AT SITE) F4 G6 B8

THIS DRAW ING AND THE INFORM ATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAIPEM .
VALVES / IN-LINE ITEMS
K
----------------------
9 K (1)-NPS:2-GATE-BB-FB-FLEX WDG-THDD 2 VS118 1 27.0
SEAT - 10
350
API600-GA-E-60104-FLGD/FLGD- STEM EAST
CL300- RF125 µIN.RA-ASTM A216 WCB K 178

-TRIM:13CR STELLITED
10 K (1)-NPS:2-GATE-BB-FB-FLEX WDG-THDD 2 VS105 1 20.0
SEAT - G6 B8 E 467460
API600-GA-E-60101-FLGD/FLGD- N 348145
CL150- RF125 µIN.RA-ASTM A216 WCB EL +10097
-TRIM:13CR STELLITED 11
11 K (1)-NPS:2-BLIND FLANGE - 2 BB038 1 2.3 K
ASME-B16.5-CL150-RF125
µIN.RA-ASTM A105
--------
TOTAL ERECTION WEIGHT 52.6
--------
---------------
| SEE SHEET 2 |
---------------
DEF
\032154\3D\ISOGEN\ISOREF\SNSNAM CHK.

NOTES Support INSUL. OPER. DES. DENOTES PIPE SPOOL NO. REFERENCE DRAWINGS
DES. BUTT
NPD LINE AREA
Piping THK. TEMP. TEMP. PRESS. COMPONENT DESCRIPTION Key Plan Piping G.A. N°
1. UNLESS OTHERWISE NOTED ALL DIMENSIONS AND COORDINATES ARE IN mm. CLASS FINISH. CODE No.
Class mm. °C °C Bar <1> CUT PIPE LENGTH PDS MODELS EAM22P00A
2. UNLESS OTHERWISE NOTED, ALL DIMENSIONS ARE TO CENTER LINE OR FACE OF FLANGES.

3. NORTH ARROW DIRECTION SHOWS CALLED PLANT NORTH. CS 2" 13S V(PP) 40.00 85.000 120.00 7.0000 8A 001 P&ID

4. FIELD WELDINGS FOR INSTALLATION MUST BE DEFINED FROM MECH. CONTRACTOR CS 2" 11G V(PP) 40.00 85.000 120.00 7.0000 8A 001 21-GD-B-06949

5. REVISION NUMBER IS SAIPEM NUMBER Stress Calc. N°

6. HANDWHEELS OR LEVERS ORIENTATION FOR VALVES MUST BE CHECKED DURING INSTALLATION.

D:

DRAWING TYPE
7. FOR SMALL BORE LINES SUPPORTS (TO BE DEFINED AT FIELD) REFER TO 00-GA-E-66006
W SCSVH009:

ISOMETRIC PIPING DETAIL

EAM 22P00A

ISO
8. FOR FLANGE OPTION CODE AND VALVE NUMBERING IDENTIFICATION REFER TO 00-GA-E-60001 WBS

9. REINFORCED PAD MUST BE WELDED IN SHOP AS PER 00-GA-E-61109 2 IFC - ENHANCEMENT-1 20-05-2023 PCA VA CE
LINE ID: 21-TL3046C-EAM22/1 EAM22
10. SUPPORT REINFORCED PLATE MUST BE WELDED IN SHOP AS PER SPC.TP.SUP.0601 (00-GA-E-66003_0_att4)
DEFAULTS FILE NO:

REV. DESCRIPTION DATE DWG. CHKD APPD AMMONIA TRAIN 2 - CO2 REMOVAL SECTION
M ODEL FILE NOS:

11. FOR SEAL WELD REQUIREMENT REFER TO 00-GA-E-60805

Welding spec. PWHT TEST PRESS.TEST TYPE GUSSET JOB ORDER DANGOTE FERTILIZER PROJECT NIGERIA
12. THE WEIGHT OF EACH SUPPORT IS SHOWN ON THE RELATED LIST FOR LINE
PLANT NO. INDEX DRAWING NUMBER SHT. NO. REV. NO.
13. BOLT HOLES OF FLANGE SHALL BE STRADDLE TO CENTER LINE OF PIPE UNLESS OTHERWISE NOTED. SPC.WL.ES.310 YES 10.49 H SEE NOTE 7
14. FOR HYDRO TEST REQUIREMENTS REFER TO 00-ZA-E-09404. 032154 21 L 21TL3046CEAM221 1/2 2
PDS DESIGN AREA: EAM22 EXTRACTION DATE: 20-MAY-2023

EXTRACTION No: 3
21-TL3046C-EAM22/1
ORIG. DWG SIZE: A2

APPROVED-S LV1 COMPLETE

 PT N.S. WEIGHT N

THIS DOCUM ENT W ITHOUT THE W RITTEN CONSENT OF ITS OW NER.

NO COMPONENT DESCRIPTION (INS) ITEM CODE SM QTY (Kg.)

------------------------
| SEE PREVIOUS SHEET 1 |
------------------------

TOTAL WEIGHT - THIS DRG 70.7

--------

-------------------
| CUT PIPE LENGTH |
-------------------
PIECE LENGTH N.S. REMARKS PIECE LENGTH N.S. REMARKS
NO (MM) (INS) NO (MM) (INS)

<1> 908 2 <2> 2421 2

NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM

THIS DRAW ING AND THE INFORM ATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAIPEM .
DEF
\032154\3D\ISOGEN\ISOREF\SNSNAM CHK.

NOTES Support INSUL. OPER. DES. DENOTES PIPE SPOOL NO. REFERENCE DRAWINGS
DES. BUTT
NPD LINE AREA
Piping THK. TEMP. TEMP. PRESS. COMPONENT DESCRIPTION Key Plan Piping G.A. N°
1. UNLESS OTHERWISE NOTED ALL DIMENSIONS AND COORDINATES ARE IN mm. CLASS FINISH. CODE No.
Class mm. °C °C Bar <1> CUT PIPE LENGTH PDS MODELS EAM22P00A
2. UNLESS OTHERWISE NOTED, ALL DIMENSIONS ARE TO CENTER LINE OR FACE OF FLANGES.

3. NORTH ARROW DIRECTION SHOWS CALLED PLANT NORTH. CS 2" 13S V(PP) 40.00 85.000 120.00 7.0000 8A 001 P&ID

4. FIELD WELDINGS FOR INSTALLATION MUST BE DEFINED FROM MECH. CONTRACTOR CS 2" 11G V(PP) 40.00 85.000 120.00 7.0000 8A 001 21-GD-B-06949

5. REVISION NUMBER IS SAIPEM NUMBER Stress Calc. N°

6. HANDWHEELS OR LEVERS ORIENTATION FOR VALVES MUST BE CHECKED DURING INSTALLATION.

D:

DRAWING TYPE
7. FOR SMALL BORE LINES SUPPORTS (TO BE DEFINED AT FIELD) REFER TO 00-GA-E-66006
W SCSVH009:

ISOMETRIC PIPING DETAIL

EAM 22P00A

ISO
8. FOR FLANGE OPTION CODE AND VALVE NUMBERING IDENTIFICATION REFER TO 00-GA-E-60001 WBS

9. REINFORCED PAD MUST BE WELDED IN SHOP AS PER 00-GA-E-61109 2 IFC - ENHANCEMENT-1 20-05-2023 PCA VA CE
LINE ID: 21-TL3046C-EAM22/1 EAM22
10. SUPPORT REINFORCED PLATE MUST BE WELDED IN SHOP AS PER SPC.TP.SUP.0601 (00-GA-E-66003_0_att4)
DEFAULTS FILE NO:

REV. DESCRIPTION DATE DWG. CHKD APPD AMMONIA TRAIN 2 - CO2 REMOVAL SECTION
M ODEL FILE NOS:

11. FOR SEAL WELD REQUIREMENT REFER TO 00-GA-E-60805

Welding spec. PWHT TEST PRESS.TEST TYPE GUSSET JOB ORDER DANGOTE FERTILIZER PROJECT NIGERIA
12. THE WEIGHT OF EACH SUPPORT IS SHOWN ON THE RELATED LIST FOR LINE
PLANT NO. INDEX DRAWING NUMBER SHT. NO. REV. NO.
13. BOLT HOLES OF FLANGE SHALL BE STRADDLE TO CENTER LINE OF PIPE UNLESS OTHERWISE NOTED. SPC.WL.ES.310 YES 10.49 H SEE NOTE 7
14. FOR HYDRO TEST REQUIREMENTS REFER TO 00-ZA-E-09404. 032154 21 L 21TL3046CEAM221 2/2 2
PDS DESIGN AREA: EAM22 EXTRACTION DATE: 20-MAY-2023

EXTRACTION No: 3
21-TL3046C-EAM22/1
ORIG. DWG SIZE: A2

APPROVED-S LV1 COMPLETE