PT320AT02-3 Product Specification_Rev.

F3

Contents
Revision History ............................................................................................................................................... 3
1. GENERAL DESCRIPTION ....................................................................................................................... 4
1.1 General Specifications ....................................................................................................................................... 4
2. ABSOLUTE MAXIMUM RATINGS ........................................................................................................ 5
2.1 Absolute Maximun Ratings ................................................................................................................................ 5
2.2 Absolute Ratings of Environment ...................................................................................................................... 5
2.3 IC Temperature Spec .......................................................................................................................................... 6
2.4 Package Storage ................................................................................................................................................. 6
3. ELECTRICAL SPECIFICATIONS .......................................................................................................... 7
3.1 Electrical Characteristics .................................................................................................................................... 7
3.1.1 Power consumption ................................................................................................................................ 7
3.1.2 LVDS characteristics .............................................................................................................................. 8
3.1.3 LVDS Format ......................................................................................................................................... 9
3.1.4 Block diagram ........................................................................................................................................ 9
3.2 Interface Connections....................................................................................................................................... 10
3.3 Timing Spec. .................................................................................................................................................... 12
3.4 Power On/Off Sequence ................................................................................................................................... 14
3.5 Flicker Adjustment ........................................................................................................................................... 15
3.6 Driver IC ESD spec .......................................................................................................................................... 15
4. OPTICAL CHARACTERISTICS ........................................................................................................... 16
4.1 Measurement Conditions.................................................................................................................................. 16
4.2 Optical Specifications ...................................................................................................................................... 17
5. MECHANICAL CHARACTERISTICS.................................................................................................. 19
5.1 Mechanical Specification ................................................................................................................................. 19
5.2 Packing ............................................................................................................................................................. 20
5.2.1 Packing specifications .......................................................................................................................... 20
6. DEFINITION OF LABELS ...................................................................................................................... 21
6.1 Open Cell Label ............................................................................................................................................... 21
6.2 Carton Label ..................................................................................................................................................... 22
6.3 Pallet Label....................................................................................................................................................... 23
7. PRECAUTION........................................................................................................................................... 24
7.1 Unpacking ........................................................................................................................................................ 24
7.2 Storage test ....................................................................................................................................................... 24
8. GP REQUIREMENT ................................................................................................................................ 24

The copyright belongs to Chuzhou HKC Optoelectronics Technology Co., Ltd.

Any unauthorized use is prohibited.
2 / 24
 PT320AT02-3 Product Specification_Rev. F3

Revision History

Version Date Page (New) Section Description Revision by

Rev. F1 2020/4/10 24 All Final Specification was First issued Shipeng Li

Rev. F2 2020/6/17 19 5.1 Remove Punch from COF Shipeng Li

Rev. F3 2020/7/8 7 3.1.1 Power consumption Shipeng Li

The copyright belongs to Chuzhou HKC Optoelectronics Technology Co., Ltd.

Any unauthorized use is prohibited.
3 / 24
 PT320AT02-3 Product Specification_Rev. F3

1. GENERAL DESCRIPTION
The specification is applied to 31.5” model (PT320AT02-3) TFT Liquid Crystal Display open cell and it supports 1366 x 768
HD mode with 16.7M （8bit）colors. This product is with driver ICs and a 30-pins-1ch-LVDS circuit board and built in without
backlight unit.

1.1 General Specifications

Item Specification Unit Note
Screen Size 31.5 inch Diagonal inch -
Outline Dimension 712.085(H)×410.57(V)x 1.4(D) mm D: cell thickness
Active area 697.685(H) x 392.256(V) mm -
Driver Element a-si TFT active matrix - -
Cell transmittance 7.0(Typ.) % HKC light，center point
Pixel Number 1366 x 768 pixel -
Sub Pixel Pitch 0.51075(H)×0.17025(V) mm -
Pixel Arrangement RGB Horizontal Island - -
Display Colors 16.7M color 8bit
Display Mode Normally Black - -
Display Orientation Signal input with “ABC” - -
Type=AG - -
Surface Treatment Haze=3% - -
Top Surface Hardness : 3H - -
Weight 894 g -
Note:

ABC
Scan direction

The copyright belongs to Chuzhou HKC Optoelectronics Technology Co., Ltd.

Any unauthorized use is prohibited.
4 / 24
 PT320AT02-3 Product Specification_Rev. F3

2. ABSOLUTE MAXIMUM RATINGS

2.1 Absolute Maximun Ratings
The followings are maximum values which, if exceeded, may cause damage to the unit.
Value
Item Symbol Unit Note
Min. Max.
Power Supply Voltage VCC -0.3 13.5 V (1)
Input Signal Voltage Vin -0.3 3.6 V (1)
Note:
(1) Within Ta=25±2°C
2.2 Absolute Ratings of Environment
Temperature and relative humidity range is shown in the figure below.
Value
Item Symbol Unit Note
Min. Max.
Storage Temperature TST -20 60 °C (1)
Operating Temperature TOP 0 50 °C (1), (2), (3)
Note:
(1) a. 90 % RH Max. (Ta ≤ 40 °C)
b. Web-bulb temperature should be 39℃ Max.(Ta>40°C)
c. No condensation
d. Operating condition with a assemble module
(2) The temperature of panel surface should be 0°C min. and 50°C max.
(3) Any point on the Driver surface must be less than 120°C under any condition. Module designer should apply adequate
thermal solutions to keep the electrical components surface temperature under control limit (ex: Source Driver IC
120°C, Components on T-con PCB 100°C). Operation over the temperature can cause damages or decrease of life time.

Fig.2.1 Operating and storage environment

The copyright belongs to Chuzhou HKC Optoelectronics Technology Co., Ltd.

Any unauthorized use is prohibited.
5 / 24
 PT320AT02-3 Product Specification_Rev. F3

2.3 IC Temperature Spec

Item D-IC TCON PWM IC Note
Silk name — U1 U2
Tc 120℃ 100℃ 100℃ (1), (2)
Note：
(1) Tc=The maximum surface temperature of IC
(2) Tc temperature shall not be exceeded under any condition
2.4 Package Storage
When storing open cell as spares for a long time, please follow the precaution instructions:
(1) Do not store the open cell in high temperature and high humidity for a long time. It is highly recommended to store the
module with temperature from 20ºC to 30ºC in normal humidity (50 ± 10%RH) with shipping package.
(2) The open cell should be keep within one month shelf life.

The copyright belongs to Chuzhou HKC Optoelectronics Technology Co., Ltd.

Any unauthorized use is prohibited.
6 / 24
 PT320AT02-3 Product Specification_Rev. F3

3. ELECTRICAL SPECIFICATIONS
3.1 Electrical Characteristics
3.1.1 Power consumption

Value
Parameter Symbol Unit Note
Min. Typ. Max.

Power Supply Voltage VCC 10.8 12.0 13.2 V (2)

Rush Current IRUSH - - 3.0 A (3)

White Pattern - - 0.33 0.47 A

Power Supply
Horizontal Stripe - - 0.46 0.65 A (4)
Current
Black Pattern - - 0.31 0.44 A

White Pattern - 3.96 5.64 Watt

Power
Horizontal Stripe Pc - 5.52 7.84 Watt
Consumption
Black Pattern - 3.72 5.28 Watt
Note:
(1) Ambient temperature: 25 ± 2ºC
(2) The ripple voltage should be controlled under 10% of VCC
(3) Measurement Conditions: VCC rising time=470μs

VCC
VCC ×0.9

VCC×0.1
GND
470μs

Fig.3.1 VCC rising time condition

The copyright belongs to Chuzhou HKC Optoelectronics Technology Co., Ltd.

Any unauthorized use is prohibited.
7 / 24
 PT320AT02-3 Product Specification_Rev. F3

(4) Measurement Conditions: Vcc =12V, Ta = 25 ± 2 ºC, Fv = 60 Hz, whereas the test pattern is shown as below.
A. White Pattern B. Dot Horizontal Stripe

C. Black Pattern

Fig.3.2 Test pattern

3.1.2 LVDS characteristics
Value
Parameter Symbol Unit Note
Min. Typ. Max.
Differential Input High
VTH +100 - - mV
Threshold Voltage
Differential Input Low
VTL - - -100 mV
Threshold Voltage
LVDS interface Common Input Voltage (1)
VCM 1.0 1.2 1.4 V

Differential input voltage |VID| 200 - 600 mV

Terminating Resistor RT 90 100 110 ohm

Input High Threshold Voltage VIH 2.7 - 3.3 V

CMOS interface
Input Low Threshold Voltage VIL 0 - 0.6 V
Note:
(1) The LVDS input signal has been defined as follows:

VTH
VCM |VID|
VTL

GND
Fig.3.3 LVDS input signal

The copyright belongs to Chuzhou HKC Optoelectronics Technology Co., Ltd.

Any unauthorized use is prohibited.
8 / 24
 PT320AT02-3 Product Specification_Rev. F3

3.1.3 LVDS Format

VESA Format: SELLVDS = L or Open

Fig.3.4 VESA format

JEIDA Format: SELLVDS = H

Fig.3.5 JEIDA format

3.1.4 Block diagram
INPUT CONNECTOR

DATA
DATA DRIVER

TIMING
VCC
CONTROLLE TFT LCD PANEL
(1366x768)
DC/DC
CONVERTER

Fig.3.6 Block diagram

The copyright belongs to Chuzhou HKC Optoelectronics Technology Co., Ltd.

Any unauthorized use is prohibited.
9 / 24
 PT320AT02-3 Product Specification_Rev. F3

3.2 Interface Connections

Interface Pin Assignment
Connector part No.: CN1 3-10122314-0 (XDYT) or equivalent 1mm pitch 30 pin (1)
Pin No. Symbol Description Note
1 VCC Power supply
2 VCC Power supply
3 VCC Power supply
4 VCC Power supply
5 GND Power Ground
6 GND Power Ground
7 GND Power Ground
8 GND Power Ground
9 SELLVDS LVDS Data Format Selection (3)
10 NC No Connection
11 GND Power Ground
12 RX0N LVDS Data(0) -
13 RX0P LVDS Data(0) +
14 GND Power Ground
15 RX1N LVDS Data(1) -
16 RX1P LVDS Data(1) +
17 GND Power Ground
18 RX2N LVDS Data(2) -
19 RX2P LVDS Data(2) +
20 GND Power Ground
21 RXCN LVDS clock -
22 RXCP LVDS clock +
23 GND Power Ground
24 RX3N LVDS Data(3) -
25 RX3P LVDS Data(3) +
26 GND Power Ground
27 NC No Connection (2)
28 NC No Connection (2)
29 NC No Connection (2)
30 GND Power Ground

The copyright belongs to Chuzhou HKC Optoelectronics Technology Co., Ltd.

Any unauthorized use is prohibited.
10 / 24
 PT320AT02-3 Product Specification_Rev. F3

Note:
(1) Following finger shows the LVDS pin1 diagram.

#1 #30

#1 #30
Fig.3.7 LVDS connector direction sketch map
(2) For HKC used only, please leave it open.
(3) High: connect to +3.3V→JEIDA Format; Low: connect to GND or Open→VESA Format.

X+C_Board PCBA

1KΩ
SELLVDS TCON
10KΩ

Input connector

Fig.3.8 WP/SDA/SCL PCBA set

(4) Connector drawings

The copyright belongs to Chuzhou HKC Optoelectronics Technology Co., Ltd.

Any unauthorized use is prohibited.
11 / 24
 PT320AT02-3 Product Specification_Rev. F3

3.3 Timing Spec.

The input signal timing specifications are shown as the following table and timing diagram.
Signal Item Symbol Min. Typ. Max. Unit Note
Frequency Fclkin 50 75.4 85 MHz (1)
Input cycle to
Trcl - - 200 ps (2)
cycle jitter
Spread spectrum
LVDS Clock Fclkin_mod Fclkin-2% - Fclkin+2% MHz
modulation range
Spread spectrum (3)
modulation FSSM 10 - 200 KHz
frequency
LVDS
Receiver Skew
Receiver TRSM -400 - 400 ps (4)
Margin
Data
Frame Rate F 48 60 62.5 Hz
Total TV 784 806 1015 TH TV = TVD + TVB
Vertical Term
Active Display TVD 768 TH
Blank TVB 16 38 247 TH
Total TH 1460 1560 2000 TCLK TH = THD + THB
Horizontal Term Active Display THD 1366 TCLK
Blank THB 94 194 634 TCLK
Attention:
The module is operated in DE only mode, H sync and V sync input signal have no effect on normal operation.
Note:
(1) Please make sure the range of pixel clock follows the following equations:
FCLK (max) ≥ Fmax × TV × TH FCLK (min) ≤ Fmin × TV × TH
TV

TVD TVB

DE
TH

DCLK

TCLK
THB THD
DE

DATA Valid Display Data

Fig.3.9 Signal timing diagram

The copyright belongs to Chuzhou HKC Optoelectronics Technology Co., Ltd.

Any unauthorized use is prohibited.
12 / 24
 PT320AT02-3 Product Specification_Rev. F3

(2) The input clock cycle-to-cycle is defined as below figures.

T T1= T±200ps T2=T1±200ps

Fig.3.10 Jitter
(3) The SSCG (Spread Spectrum Clock Generator) is defined as the following figure.
The LVDS SSM's suggestion is off by default, SOC board must test all validation if SOC board open the LVDS SSM.

Fig.3.11 SSCG
(4) The LVDS timing diagram and setup/hold time is defined and showed as the following figure.

Fig.3.12 LVDS receive interface timing diagram

The copyright belongs to Chuzhou HKC Optoelectronics Technology Co., Ltd.

Any unauthorized use is prohibited.
13 / 24
 PT320AT02-3 Product Specification_Rev. F3

3.4 Power On/Off Sequence

The power sequence specifications are shown as the following table and diagram.

90% 90%

10% 10% 10%

Vcc
T1 T2 T5 T6
Valid data
Signal
T3 T4

OFF ON OFF
Backlight

Fig .3.13 Power on/off signal sequence

Values
Parameters Units
Min. Typ. Max.
T1 0.5 - 10 ms
T2 0 - 50 ms
T3 500 - - ms
T4 100 - - ms
T5 0 - 50 ms
T6 1000 - - ms
Attention:
(1) The supply voltage of the external system for the module input should be the same as the definition.
(2) To avoid some abnormal display noise, we suggest "VCC falling time" to follow "T6" definition.
(3) The product should be always operated within above ranges.
(4) In case of VCC is off level, please keep the level of input signals on the low or keep high impedance.

The copyright belongs to Chuzhou HKC Optoelectronics Technology Co., Ltd.

Any unauthorized use is prohibited.
14 / 24
 PT320AT02-3 Product Specification_Rev. F3

3.5 Flicker Adjustment

Flicker must be optimized after module assembly and aging. Its patterns are as follow:
Dot On/Off sub pixel checker under 50% gray level.

Frame N Frame N+1

Fig.3.14 Flicker pattern

3.6 Driver IC ESD spec

If the LCD module is designed with the Plastic Bezel, we suggest ESD protection solutions should be applied to avoid IC
damaged, as shown in Fig.3.15.

Fig.3.15 Source COF IC ESD protection

The copyright belongs to Chuzhou HKC Optoelectronics Technology Co., Ltd.

Any unauthorized use is prohibited.
15 / 24
 PT320AT02-3 Product Specification_Rev. F3

4. OPTICAL CHARACTERISTICS
4.1 Measurement Conditions
The table below is the test condition of optical measurement.
Item Symbol Value Unit

Ambient Temperature TA 252 ºC

Ambient Humidity HA 5010 % RH

Supply Voltage VCC 12 V

Driving Signal Refer to the typical value in Chapter 3: Electrical Specification

Vertical Refresh Rate Fv 60 Hz

Light source HKC 31.5” WXGA module White LED Backlight Module/ Film structure

Warm up time Twarm >30 min min

Dark room ED 1lux> lux

To avoid abrupt temperature change during optical measurement, the measurement should be executed in a stable, windless, in
dark room after lighting the light source.

Fig.4.1 Measurement equipment

The copyright belongs to Chuzhou HKC Optoelectronics Technology Co., Ltd.

Any unauthorized use is prohibited.
16 / 24
4.2 Optical Specifications
The relative measurement methods of optical characteristics are shown in 4.2. The following items should be measured under
the test conditions described in 4.1 and stable environment shown in 4.1.
Item Symbol Condition Min. Typ. Max. Unit Note
Rx (0.618)
Red
Ry (0.329)
θx=0°,θy=0°
Gx (0.315)
Green Viewing Angle at
Color Chromaticity Gy (0.584)
Normal Direction at Typ - 0.03 Typ + 0.03 - (1)
(CIE1931) Bx (0.152)
Blue center point of
By (0.058)
panel,
Wx (0.287)
White Light source is
Wy (0.289)
HKC Backlight
Color Gamut CG 58 62 % (2)
Transmittance T% 6.3 7 % (3)
Contrast Ratio CR 2400 3000 - (4)
θx=0°,θy=0°
Response Time Tg - 8.5 17 ms (5)
θx+ - 89 -
Horizontal
θx - - 89 -
Viewing Angle CR≧10 Deg. (6)
θy+ - 89 -
Vertical
θy- - 89 -
Note:
Light source here is the backlight of HKC Module, and film structure is two diffuser sheets.
(1) Each chromaticity coordinates (x, y) are measured in CIE1931 color space when full-screen displaying (Red,
Green, Blue, White) and light source is defined by HKC Backlight, Measurements shall be made at the center of
the panel, and setup of measurement is shown in Fig 4.1.
(2) The color gamut is defined as the fraction in percent of the area of the triangle bounded by R, G, B coordinates and
the area is defined by NTSC 1931 color standard in the CIE color space. Chromaticity coordinates are measured by
CS2000 and the standard setup of measurement is shown in Fig 4.1.
(3) Definition of Transmittance (T%):
The transmittance is measured with full white pattern (Lmax) at the center of the LCD panel.

Luminance of LCD module

Transmittance (T%)ൌ
Luminance of backlight
(4) Definition of Contrast Ratio (CR):
The contrast ratio can be calculated by the following expression,

࡯ࡾ࢝
Contrast Ratio (CR): ࡯ࡾ ൌ
࡯ࡾࡰ

CRW : Luminance of LCD module with full screen white pattern (255,255, 255) at center point.
CRD : Luminance of LCD module with full screen Dark pattern (0, 0, 0) at center point.
Where the measure point of to the Contrast Ratio is the center of the panel

The copyright belongs to Chuzhou HKC Optoelectronics Technology Co., Ltd.

Any unauthorized use is prohibited.
17 / 24
 (5) Definition of Response time (Tg):
Average of gray to gray response time (Tg) means the average switching time of luminance ratios among
0%,25%,50%,75%,and 100% to each other and is optimized on frame rate =60Hz.
To
Measured Response time
0% 25% 50% 75% 100%
0% T0%to25% T0% to 50% T0% to 75% T0% to 100%
25% T25% to 0% T25% to 50% T25% to 75% T25% to 100%
From 50% T50% to 0% T50% to 25% T50% to 75% T50% to 100%
75% T75% to 0% T75% to 25% T75% to 50% T75% to 100%
100% T100% to 0% T100% to 0% T100% to 50% T100% to 75%
Table 4.2 Switching time of luminance ratios matrix

Fig.4.3 The definition of TR and TF

Measured response time is determined by 10% to 90% brightness difference of rising (TR) or falling (TF) time.
(6) Definition of Viewing angle:
As Note (4) the static contrast ratio definition, the viewing angles are defined at the angle that the contrast
ratio is larger than 10 at four directions relative to the perpendicular direction of the HKC’s module (two
vertical angles: up θy+ and down θy-; and two horizontal angles: right θx+ and left θx-). The standard setup of
measurement is shown in Fig 4.1 & 4.4.

Fig.4.4 Definition of Viewing angle

The copyright belongs to Chuzhou HKC Optoelectronics Technology Co., Ltd.

Any unauthorized use is prohibited.
18 / 24
5. MECHANICAL CHARACTERISTICS
5.1 Mechanical Specification

The copyright belongs to Chuzhou HKC Optoelectronics Technology Co., Ltd.

Any unauthorized use is prohibited.
19 / 24
5.2 Packing
5.2.1 Packing specifications
Specification
Item
Quantity Dimension (mm) Item Weight (Kg)
Net Weight 15.6
Packing Box 17pcs/box 857(L) x 577(W) x 105(H)
Gross Weight 16.4
Pallet 1 1200(L) x 900(W) x 150 (H) Net Weight 16.5

Stack Layer 9

Boxes per Pallet 18

Pallet after Packing 306pcs/pallet 1200(L) x 900(W) x 1038(H) Gross Weight 315.96

The copyright belongs to Chuzhou HKC Optoelectronics Technology Co., Ltd.

Any unauthorized use is prohibited.
20 / 24
6. DEFINITION OF LABELS
6.1 Open Cell Label

XXXXXXXXXXXXXXXXXXXXX YMDD PT320AT02-3 Ver.X.X

Model Version Code

Model Name

Manufactured Date

Serial
SerialNumber
Number

Serial Number: XXXXXXXXXXXX XXXXXXXXX

HKC Internal Use

Panel ID

Manufactured Date: Y M DD
Date: 01~31

Month: 1~9, A~C, for Jan.~Dec

Year: 2017=7, 2018=8, 2020=0……

Model Name: PT320AT02-3

Model Version Code: Ver.X.X, for example: 0.0,0.1…,1.0,1.1….,2.0,2.1……

The copyright belongs to Chuzhou HKC Optoelectronics Technology Co., Ltd.

Any unauthorized use is prohibited.
21 / 24
6.2 Carton Label

Serial Number: XXXXXXXX XX XXXX XXXXXX

HKC Internal Use

Manufactured Date

Model Version Code

HKC Internal Use

Box ID: XX XXX XXXXX

HKC Internal Use

Panel Size

HKC Internal Use

Model Version Code: Ver.X.X, for example: 0.0,0.1…,1.0,1.1….,2.0,2.1……

The copyright belongs to Chuzhou HKC Optoelectronics Technology Co., Ltd.

Any unauthorized use is prohibited.
22 / 24
6.3 Pallet Label

Serial Number: XXXXXXXX XX XXXX XXXX XXXXXX

HKC Internal Use

Cell Quantity

Manufactured Date

Model Version Code

HKC Internal Use

Pallet ID: XXXXXXXX

The copyright belongs to Chuzhou HKC Optoelectronics Technology Co., Ltd.

Any unauthorized use is prohibited.
23 / 24
7. PRECAUTION
Please pay attention to the followings when a TFT-LCD cell is used, handled and mounted.
7.1 Unpacking
Should use immediately after unpacking TFT-LCD cell to prevent the terminal corrosion.
Protection film for a polarizer on a TFT open cell should be slowly peeled off so that the electrostatic charge can be
minimized.
Source PCB should be connected to the ground when peel off the protection film.
The protection film should not be contacted to the driver during peeling off.

7.2 Storage test

Any attachment on polarizer of open-cell, such as tape, is forbidden and not recommend, especially under the high temperature
and high humidity environment.

8. GP REQUIREMENT
a) RoHS, Directive 2011/65/EU of the European Parliament and council of 1 July 2011
b) RoHS, Directive (EU) 2015/863 of the European Parliament and council of 31 March 2015
c) PPW

The copyright belongs to Chuzhou HKC Optoelectronics Technology Co., Ltd.

Any unauthorized use is prohibited.
24 / 24