Related Product: MMS-8728E, MMS-6710P, MMS-8728EF,
MMS-8830, MMS-9728, MMS-6728-P, MMS-7728, MMS-9764H,
MMS-7710, MMS-8838F
Backuplink Configuration
Commands
Table of
Contents
Table of Contents
Chapter 1 BackupLink Configuration Commands...........................................................1
1.1Global Commands.............................................................................................. 1
1.1.1....................................................................................backup-link-group id
1
1.1.2......................backup-link-group id preemption-mode forced {delay value}
2
1.1.3................backup-link-group id preemption-mode bandwidth {delay value}
2
1.1.4...................................................................................monitor-link-group id
3
1.2Port Configuration Commands............................................................................4
1.2.1..........................................................................backup-link-group id active
4
1.2.2........................................................................backup-link-group id backup
5
1.2.3...............................................................................share-load vlan vlanmap
6
1.2.4................................................................backup-link-group mmu transmit
7
1.2.5..................................................................backup-link-group mmu receive
8
1.2.6.........................................................................monitor-link-group id uplink
8
1.2.7....................................................................monitor-link-group id downlink
9
1.3Show................................................................................................................. 10
1.3.1...........................................................................show backup-link-group id
10
1.3.2..........................................................................show monitor-link-group id
11
-I
-
BackupLink Configuration
Commands
Chapter 1 BackupLink Configuration
Commands
1.1 Global Commands
1.1.1 backup-link-group id
To set the BackupLink group, run the following command:
backup-link-group id
To delete the BackupLink group, run the following command:
no backup-link-group id
Parameter
Parameter Descriptio
n
Id Stands for the instance ID of the backuplink group.
Default value
The backuplink group is not configured by default.
Command mode
Global configuration mode
Explanation
N/A.
Example
Switch_config#backup-link-
group 1 Switch_config#
Related command
N/A.
- 1-
BackupLink Configuration
Commands
1.1.2 backup-link-group id preemption-mode forced {delay value}
To set the port-based preemption mode for the backuplink group, run the
following command:
backup-link-group id preemption-mode forced {delay value}
To delete the port-based preemption mode for the backuplink group, run the
following command:
no backup-link-group id
Parameter
Parameter Descriptio
n
Id Stands for the instance ID of the backuplink group.
value Stands for the delay time.
Default value
The backuplink group has not been set with the trait of port-based
preemption by default.
Command mode
Global configuration mode
Explanation
The backup-link-group id preemption-mode forced {delay value} command can
be used to create the backuplink group directly.
Example
Switch_config#backup-link-group 1 preemption-mode
forced delay 5 Switch_config#
Related command
backup-link-group id
backup-link-group id preemption-mode bandwidth {delay value}
1.1.3 backup-link-group id preemption-mode bandwidth {delay value}
To set port bandwidth preemption mode for the backuplink group, run the
following command:
- 2-
BackupLink Configuration
Commands
backup-link-group id preemption-mode bandwidth {delay value}
To delete port bandwidth preemption mode for the backuplink group, run the
following command:
no backup-link-group id
Parameter
Parameter Descriptio
n
Id Stands for the instance ID of the backuplink group.
value Stands for the delay time.
Default value
The backuplink group has not been set with the trait of port bandwidth
preemption by default.
Command mode
Global configuration mode
Explanation
N/A.
Example
Switch_config#backup-link-group 1 preemption-mode
bandwidth delay 5 Switch_config#
Related command
backup-link-group id
backup-link-group id preemption-mode forced {delay value}
1.1.4 monitor-link-group id
To set the MonitorLink group, run the following command:
monitor-link-group id
To delete the MonitorLink group, run the following command:
no monitor-link-group id
- 3-
BackupLink Configuration
Commands
Parameter
Parameter Descriptio
n
Id Stands for the instance ID of the monitorlink group.
Default value
The MonitorLink group is not configured by default.
Command mode
This command is run in global configuration mode.
Explanation
N/A.
Example
Switch _config# monitor-link-
group 1 Switch_config#
Related command
N/A.
1.2 Port Configuration Commands
1.2.1 backup-link-group id active
To set a port to be an active port, run the following command:
backup-link-group id active
To cancel the active port, run the following command:
no backup-link-group id
Parameter
Parameter Descriptio
n
Id Stands for the instance ID of the backuplink group.
Default value
The primary port is not configured by default.
- 4-
BackupLink Configuration
Commands
Command mode
The physical port configuration mode and the converged port configuration
mode
Explanation
If the backuplink group is not established, it will be automatically created
when you configure the backuplink group on a port directly.
Example
Switch_config#interface gigaEthernet 0/1
Switch_config_g0/1#backup-link-group 1
active Switch_config_g0/1#exit
Related command
backup-link-group id
backup-link-group id backup
1.2.2 backup-link-group id backup
To set a port to be a backup port, run the following command:
backup-link-group id backup
To cancel the backup port, run the following command:
no backup-link-group id
Parameter
Parameter Descriptio
n
Id Stands for the instance ID of the backuplink group.
Default value
The backup port is not configured by default.
Command mode
The physical port configuration mode and the converged port configuration
mode
- 5-
BackupLink Configuration
Commands
Explanation
If the backuplink group is not established, it will be automatically created
when you configure the backuplink group on a port directly.
Example
Switch_config#interface gigaEthernet 0/1
Switch_config_g0/1#backup-link-group 1
backup Switch_config_g0/1#exit
Related command
backup-link-group id
backup-link-group id active
1.2.3 share-load vlan vlanmap
To set VLAN load balance for the backup port, run the following command:
share-load vlan vlanmap
To delete VLAN load balance for the backup port, run the following command:
no share-load vlan
Parameter
Parameter Descriptio
n
vlanmap Stands for the VLAN value.
Default value
VLAN load balance is not set for the backup port by default.
Command mode
The physical port configuration mode and the converged port configuration
mode
Explanation
This command can be set only on the backup port, that is, a port must be
set to be a backup port before VLAN load balance is set on the port.
Different BackupLink groups can be set to have the same VLAN group or
the overlapped VLAN segments. If there are overlapped VLAN segments,
the system will classify these VLANs into different MSTs (STGs) and
conduct operations toward a
- 6-
BackupLink Configuration
Commands
group of ports, the statuses of these ports in different MSTs vary. So, you'd
better rule out those overlapped VLAN groups when configuring load balance
for VLANs.
Example
Switch_config#interface gigaEthernet
0/1 Switch_config_g0/1# share-load
vlan 100-200 Switch_config_g0/1#exit
Related command
backup-link-group id
backup-link-group id backup
1.2.4 backup-link-group mmu transmit
To set MMU transmission for the ports of the backuplink group, run the
following command:
backup-link-group mmu transmit
To delete MMU transmission for the ports of the backuplink group, run
the following command:
no backup-link-group mmu
Parameter
N/A.
Default value
The MMU transmission function for the ports of the backuplink group is
not set by default.
Command mode
The physical port configuration mode and the converged port configuration
mode
Explanation
Only the ports of the backuplink group can be set to transmit, that is, the
ports must be set to active or backup.
Example
Switch_config#interface gigaEthernet 0/1
- 7-
BackupLink Configuration
Commands
Switch_config_g0/1#backup-link-group mmu
transmit Switch_config_g0/1#exit
Related command
backup-link-group id
1.2.5 backup-link-group mmu receive
To set MMU reception for ports, run the following command:
backup-link-group mmu receive
To delete MMU reception for ports, run the following command:
no backup-link-group mmu
Parameter
N/A.
Default value
The MMU reception function for the ports is not set by default.
Command mode
The physical port configuration mode and the converged port configuration
mode
Explanation
The ports that are set to receive are not necessarily the ports of the
backuplink group.
Example
Switch_config#interface gigaEthernet 0/1
Switch_config_g0/1#backup-link-group mmu
receive Switch_config_g0/1#exit
Related command
N/A.
1.2.6 monitor-link-group id uplink
To set a port to be an uplink port, run the following command:
- 8-
BackupLink Configuration
Commands
monitor-link-group id uplink
To cancel the uplink port configuration, run the following command:
no monitor-link-group id
Parameter
Parameter Descriptio
n
Id Stands for the instance ID of the monitorlink group.
Default value
The uplink port is not configured by default.
Command mode
The physical port configuration mode and the converged port configuration
mode
Explanation
If the Monitorlink group is not established, it will be automatically created
when you configure the Monitorlink group on a port directly.
Example
Switch_config#interface gigaEthernet 0/1
Switch_config_g0/1# monitor-link-group 1
uplink Switch_config_g0/1#exit
Related command
monitor-link-group id
monitor-link-group id downlink
1.2.7 monitor-link-group id downlink
To set a port to be a downlink port, run the following command:
monitor-link-group id downlink
To cancel the downlink port configuration, run the following command:
no monitor-link-group id
- 9-
BackupLink Configuration
Commands
Parameter
Parameter Descriptio
n
Id Stands for the instance ID of the monitorlink group.
Default value
The downlink port is not configured by default.
Command mode
The physical port configuration mode and the converged port configuration
mode
Explanation
If the Monitorlink group is not established, it will be automatically created
when you configure the Monitorlink group on a port directly.
Example
Switch_config#interface gigaEthernet 0/1
Switch_config_g0/1# monitor-link-group 1
downlink Switch_config_g0/1#exit
Related command
monitor-link-group id
monitor-link-group id uplink
1.3 Show
1.3.1 show backup-link-group id
To display the information about the backuplink group, run the following
command:
show backup-link-group id
Parameter
Parameter Descriptio
n
Id Stands for the instance ID of the backuplink group.
- 10
BackupLink Configuration
Commands
Default value
N/A.
Command mode
Monitoring mode, global configuration mode, node configuration mode or
port configuration mode
Explanation
N/A.
Example
Switch_config# show backup-link-group 1
Active Interface Backup Interface State Vlan State
GigaEthernet0/2 GigaEthernet0/4 Forward/Block Block/Block
Share load vlan: 100-200,port[GigaEthernet0/4] vlan state: Forwarding
Preemption Mode: No Preempt
Preemption Delay: 0 seconds
Related command
N/A.
1.3.2 show monitor-link-group id
To display the information about the monitorlink group, run the following
command:
show monitor-link-group id
Parameter
Parameter Descriptio
n
Id Stands for the instance ID of the monitorlink group.
- 11
BackupLink Configuration
Commands
Default value
N/A.
Command mode
Monitoring mode, global configuration mode, node configuration mode or
port configuration mode
Explanation
N/A.
Example
Switch_config#show monitor-link-group 1
uplink interface: GigaEthernet0/2
Forwarding downlink interface:
GigaEthernet0/1
Forwarding GigaEthernet0/3
Forwarding
Related command
N/A.
- 12
