FOR THOSE WHO HAVE SKILLS

Voltrolysis
Explanation For those who want to know
===================================
Electrolysis
i In chemistry and manufacturing, electrolysis is a technique that uses a
direct electric current
(DC) to drive an otherwise non-spontaneous chemical reaction.
Electrolysis is commercially important
as a stage in the separation of elements from naturally occurring
sources such as ores using an electrolytic cell.
Very Different from Voltrolysis cell Electrolysis uses a variety of salts
electrolyte to cause a dielectric breakdown
and high amp draw to disassociate chemical bonds creating a exothermic
heat in the process.
=========================================================================
================================
Voltrolysis
by Stanley Meyer In Chemistry and Ionization and Disassociation of Gas is
a technique Using no Electrolyte
and uses a a Indirect Voltage Source a Voltage Plasma Field Based on a
DC to Cause the Ionic Dissociation
of Chemical Bonds in Liquids and Gas Chemistry. The primary coil is
electrically isolated (no electrical connection
between primary and secondary coil) to form Voltage Intensifier Circuit

Voltage amplitude or voltage potential is increased when secondary coil

is wrapped with more turns of wire.
Isolated electrical ground (J) prevents electron flow from input circuit
ground causing a Charge on Cell Plates
and a Volt Based Plasma Field which acts as a Catalyst to dissociate
chemical Bonds. Very Different from Electrolytic
cells and Not Electrolysis as no electrolyte. A Low Amp high Voltage
Solution Similar to how a Fluro Light
Works with a choke/ballast restricting amps Having a Cold Process with
little of no Exothermic Reaction
heat as no electrolyte no shorting of cell and no grounding the dissolved
gases which makse the water a fuel a carrier.?

So Use Volts not amps and BIngo your alot closer

Thermo
THE WATER FUEL CELL AND THE FIRST AND SECOND LAWS OF THERMODYNAMICS
The Water Fuel Cell technology encounters a credibility gap because it
appears to run counter to the long
established laws governing our interpretation of Nature. In fact, the
water Fuel Cell is entirely natural.
It merely demonstrates a new and revolutionary way of harnessing what
nature has always had on offer.
It does not infringe the two main laws of thermodynamics, i.e.:

THE FIRST LAW: "The total energy of a theromdynamic system remains

constant although it may be transformed
from one form to another." In the case of Water Fuel Cell technology, the
system is global. The
energy required to drive the engine comes from the zero-point energy
contained in the water, a virtually
inexhaustible source. The exhaust from the engine is water vapour which
returns to the atmosphere.
Manage
 THE SECOND LAW: As originally formulated by R. Clausius in 1865, this
law states that "The entropy of
the World strives towards a maximum". As recently formulated by Prigogine
and Stengers, this law "contains
two fundamental elements: (1) a negative one that expresses the
impossibility of certain processes (e.g.
heat flowing from a cold to a hot source) and (2) a positive,
constructive one. It is the impossibility of
certain processes that permits us to introduce a function, entropy, which
increases uniformly and behaves as
an attractor for isolated systems". It is at maximum when the system is
in equilibrium. Non-equilibrium is the
source of order and brings order out of chaos. Since Water Fuel Cell
technology postulates non-equilibrium,
it can be said to be supported by the positive element of this Law.?

Gas Processor Purpose remove electrons from ambiant air and hho to stop
it forming to water ,
and thus creat a new (not HHo gas) one that is thermal explosive with
more force than heat power.
below is a rough guide to doing thay

Daniel Donatelli the circuit stan had on gas processor part sent in micro
pulses we can do very fast pulses
on 3 different t circuits to and from gas processor 1st circuit drives in
pwm 5 khz up 12 volt pulses
going though a h bridge transformer up to high voltage which includes
ballasts/ chokes to restrict amps
like a fluro light start box set , it is gated with a over lay gate 5 khz
in the gate off time the electrodes
\ are used to extract electrons from gas it happens in pico second times
if possible or fast as circuit can
allow we have a 2nd circuit draw off electrons from the gas that power is
used to go into a 9xd or similar
power cap and control 12 volt and adjust abot amps lets say 5 to 10 amp
its drives a picosecond driver and
vcsell laser diode array which pulses and shines into the gas processor
as well these light pulse help keep
gas energizes and knock arround electrons for extraction it is a storm
in the of voltage and light the NM of
electrons is under debate but we know the broad spectrum is Cool White
that will hit every spectrums like a aura,
and it you alternated with uv you would hit most of them and get the
goals across all of them energy state orbits
it happen instantly, the things is the oxygen electrons are in pairs so
that are fairly easy to knock off compared
to other atoms so time to build below is a diagram from stan shown back
concept the 9xd and pico laser diode drive
not shown the following 2 circuit are the circuit 1 and circuit 2
alternating

The Hydrogen Industry and on Demand Industry is Global and Using Voltage
not amps like a Fluro Light Transformer
and ballast does and no electrolyte use is the way this avoids the
amps draw and thus the water releases extra
electrons which are already held there like a battery nothing is
consumed or lost as it is a global system just like
charge build up of lightening the energy is not used it is moved
causing magnetsium on the plates
and acts as a catalyst
which we avoid and restricts amps , we use only volts from alternator
not the amps KEY POINT and thus very different

Please Join these FB Groups We have alot of people building and sharing
advanced
technology https://www.facebook.com/groups/HHOPhilippines/
and https://www.facebook.com/groups/201797917049429/?

Please Remember Subscribe to 1 Year Subscription to Fuel Training Data

and I send you links for 2 data sites of Meyers items and parts with log
in s
$25
https://form.jotform.me/70081728711453

This is the most important example

this is a tank circuit we make volts 12 volts we put into a 200 turn or
similar transformer, our comes higher volts, it goes into chokes ,
chokes are tuned wound to resonance to cell resistance, ( choke can be
another transformer with primary as choke and secondary
not used and shorted to its self to keep it neutral)

there is also a Diode to stope volts leaving cell a oneway in no way out
item,

this means it causes a bounce or ring in in the circuit as voltage is

bounced inside and held there we, tune with coil and
cell as it is a lc tank circuit ,,
================================================
we have a dielectric layer inside the outer tube the cathode of wet cell,
this layer can be just water polarized or a ceramic build up
or coating or dielectric varnish or most common is quartz tube for the
purpose (like you see in air ionizers) , basically it is a capacitor
layer,
the voltage builds up there, the water goes between the layer and
negative centre tube, so we have a water capacitor wet cell.
=================================================== The Circuit Driver a
PWM we have 5 hkz pulse with a overlayed 5 khz gate the gate rests
cell briefly , to to avoid the dead short ,
================================================

which would ground out capacitance build up and prevent capacitence

effect in cell so we can not have salt or electrolyte in this system.
================================================
. we have a diode the diode holds the voltage in the wet cell capacitor
water voltrolysis cell, during gate period of circuit
so no back spike blows up our pwm cicuirt during the gat time . and does
not ionize our choke transformer coils, with back spike.

================================================
Having this excellent design causes a ringing or a bounce which keeps
voltage we sent in in the cell and cell charged up with volts
and with very little current or amp draw, just as a fluro light works,
================================================
Except if we put a capacitor in a fluro light it would build up voltage
very very high too and start splitting the gas beyond just
emitting light ) this is what we do we let it compound and scale to do
just that ) ================================================
( so as a example lets say we put in 900 to 1500 volts, the gate occurs,
the voltage try to leave during gate time .

But it can not as no dead short, no salts, no ground and no exit due to
diode, or h bridge isolating cell circuit ,

=================================================== so voltage is
bounced back to water cell and hits it again like a rebounded wave ,

like another pwm in, the voltage has a slight drop

let say cell goes to 1100 volts from the 1500 put in as a example
only so people can visualize ,
================================================

the gate than the gate opens from pwm again and it sends in another 990
to 1500 volts pulsed in in 5 khz this creates

a step charge the voltage capacitance climbs with each pulse

"THE STAN MEYER STEP CHARGE"
================================================ ,

This Voltage adds to the first remaining voltage held in the dielectric
layer in the west cell that the water is exposed too ,
===============================================
example 1100 volts + 900-1500 = aprox 2000 to 2500 now in cell , the gate
occurs again voltage trys to leave but can't

it bounces and reflected back into cell, and we hit it again and again
and again,

================================================ what happens is we build

up the voltage on the dielectric layer

it starts to ionize the water the h20 polarizes and it starts to have
very great magnetisium on the dielectric layer and
on anode and cathode in the wet cell with no salt no electrolyte .
================================================ ,

the water splits gases are separated use no current or amps as we use the
magnetisium of the voltage build up = VOLTROLYSIS

================================================
electrons flood the cell as the energy bouncing around start knocking
them off into water and add these electrons further
add to held charge and our pwm & voltage intensifier efforts .
================================================ , , now this is the
basics, this is what happens this is why and how voltage
gets in there, the more tuned the chokes and pwm are with the tank
circuit using ppl the better and faster it does that,

================================================ now it does get such

high voltage that the bounce can turn dc (which we

have to have) to be ac, we do not want that , so we use a hbridge to

switch in a extract circuit during gate this is happening
fast , it pulls out extract electrons being freed from broken bonds that
would create a ac, so we draw it down, we run it into

a 9xd voltage regulator that regulator can run a picsecond driver for
vcsell diodes white band cold, which can hit all the
nm band of light we can also have uv also well, we want to have a full
auro faced back into cell, this will create a light storm

these knock more electrons off faster. ,

================================================

Now we have very power gas it is a h and o with electrons stripped off it
will no reform back to water unless it

gets more electrons, so we do not want salt in there no electrolyte, but

we also do not want to ground the cell ,

the cell water or the gas, (THIS IS A COLD PROCESS WATER STAY UNDER 40 C
cold to touch ) ( cold water is like a sponge
it hold gas) ( we can meter mic fill the water) so as gas or water with
dissolved gas in it leaves cell all pipe manifold
engine block etc must be positive charged so no negative electrons can
ground gas to inert state.

================================================ when the spark finally

happens the force is explosive not implosive any more,

and thus has greater force than just heat, as the gas struggle to find
electrons the rip apart neighboring water and other

other gases to get them and often that includes nox and no which is in
the water and air

================================================ Now you know this and

you understanding clearly what is occurring
please teach it . ================================================ Part 2
is the gas processor , as do need to mix some
air into the engine we know we absolutely can not use ambient air as that
would give electrons back to our new non HHO gas
or water fuel mix, , so we must control the ambient air access which
means manifold and air intake no leaks, we use a
diaphragm to control the ambient airs access so only what engine needs is
vacuumed into the gas processor ,

================================================ the gas process is the

same system as described above except it strips

and separates the n and the o into unstable elements that find it hard to
reform with missing electrons , we do all of

this with the new key skill of making sure nothing can ground back out
ingredients, we do everything we can thing off to

extract electrons all along the way to the cylinder than means + engine
block too. ( not the whole car just the fuel line

and engine block) ================================================

So I would Invite you all to copy paste save and share this to as many
forums and website and inventive ways as you can,
This is the Stan Meyer Culture

Please Remember Subscribe to 1 Year Subscription to Fuel Training Data

and I send you links for 2 data sites of Meyers items and parts with log
in s
$25
https://form.jotform.me/70081728711453
 PS by the way this new Gas will burn bright as the sun and emit as much
light as the sun ENJOY THE TECHNOLOGY.

Begin Here
Secure Supplies
https://youtu.be/-gLmoWHmBJE

FOR THOSE WHO HAVE SKILLS

Voltrolysis
Explanation For those who want to know
===================================
Electrolysis
i In chemistry and manufacturing, electrolysis is a technique that uses a
direct electric current
(DC) to drive an otherwise non-spontaneous chemical reaction.
Electrolysis is commercially important
as a stage in the separation of elements from naturally occurring
sources such as ores using an electrolytic cell.
Very Different from Voltrolysis cell Electrolysis uses a variety of salts
electrolyte to cause a dielectric breakdown
and high amp draw to disassociate chemical bonds creating a exothermic
heat in the process.
=========================================================================
================================
Voltrolysis
by Stanley Meyer In Chemistry and Ionization and Disassociation of Gas is
a technique Using no Electrolyte
and uses a a Indirect Voltage Source a Voltage Plasma Field Based on a
DC to Cause the Ionic Dissociation
of Chemical Bonds in Liquids and Gas Chemistry. The primary coil is
electrically isolated (no electrical connection
between primary and secondary coil) to form Voltage Intensifier Circuit

Voltage amplitude or voltage potential is increased when secondary coil

is wrapped with more turns of wire.
Isolated electrical ground (J) prevents electron flow from input circuit
ground causing a Charge on Cell Plates
and a Volt Based Plasma Field which acts as a Catalyst to dissociate
chemical Bonds. Very Different from Electrolytic
cells and Not Electrolysis as no electrolyte. A Low Amp high Voltage
Solution Similar to how a Fluro Light
Works with a choke/ballast restricting amps Having a Cold Process with
little of no Exothermic Reaction
heat as no electrolyte no shorting of cell and no grounding the dissolved
gases which makse the water a fuel a carrier.?

So Use Volts not amps and BIngo your alot closer

Thermo
THE WATER FUEL CELL AND THE FIRST AND SECOND LAWS OF THERMODYNAMICS
The Water Fuel Cell technology encounters a credibility gap because it
appears to run counter to the long
established laws governing our interpretation of Nature. In fact, the
water Fuel Cell is entirely natural.
It merely demonstrates a new and revolutionary way of harnessing what
nature has always had on offer.
It does not infringe the two main laws of thermodynamics, i.e.:
THE FIRST LAW: "The total energy of a theromdynamic system remains
constant although it may be transformed
from one form to another." In the case of Water Fuel Cell technology, the
system is global. The
energy required to drive the engine comes from the zero-point energy
contained in the water, a virtually
inexhaustible source. The exhaust from the engine is water vapour which
returns to the atmosphere.
Manage

THE SECOND LAW: As originally formulated by R. Clausius in 1865, this

law states that "The entropy of
the World strives towards a maximum". As recently formulated by Prigogine
and Stengers, this law "contains
two fundamental elements: (1) a negative one that expresses the
impossibility of certain processes (e.g.
heat flowing from a cold to a hot source) and (2) a positive,
constructive one. It is the impossibility of
certain processes that permits us to introduce a function, entropy, which
increases uniformly and behaves as
an attractor for isolated systems". It is at maximum when the system is
in equilibrium. Non-equilibrium is the
source of order and brings order out of chaos. Since Water Fuel Cell
technology postulates non-equilibrium,
it can be said to be supported by the positive element of this Law.?