IC-602A Image Controller
INSTALLATION MANUAL
Applied Machine: C1070/C1060/C1060L
COLOR PRESS: 71/61 COLOR PRO: 61L
Product Code: A50U/A50V/A5VM
I.Confirmation Prior to Installation III. Installation procedure
1. Precautions against static electricity. 1. Remove the duct cover. (5 screws)
• Keep the security kit in an anti-static bag while
transporting it or storing it.
• When working in places where static electricity
tends to accumulate, such as on a carpet, dis-
charge electricity from your body by touching any
metallic portion before handling the security kit.
2. Do not touch the contacts on the security kit with
your hands, as that may result inpoor conductivity.
3. Do not physically damage the security kit by drop-
ping it, bending it, etc.
Note:
• For the installation of the UK-104 and the Duct cover
UK-207, the IC-602 is required.
• When installing the UK-104, be sure to install A5A9IXC003CA
it when the operation check by the test print
is completed after installing the IC-602. 2. Remove the rear cover/1 and the rear cover/2.
• For the installation procedures, refer to the (Rear cover/1: 4 screws, rear cover/2: 17 screws)
installation manuals of the UK-104 and the
UK-207.
II. Accessory parts
No. Name Shape Q’ty
1. IC-602 Rear
cover/2
1
A5A9IXC001CA
2. Memory Rear cover/1
1
A5A9IXC002CA A5A9IXC004CC
3. CD-ROM 3. Remove the arm cover (Rr). (2 screws)
each
1
A213IXC002CA
4. Installation
manual
1
Arm cover (Rr)
After unpacking, be sure to get rid of the
packaging materials and keep them out of
A5A9IXC005CB
the reach of children.
Putting the head in the plastic bag involves
danger of suffocation.
E-1 A5A9955001
4. Remove 2 caps and remove the cover/3. (2 screws) (3) Remove the board cover. (1 screw)
Note:
Caps When removing the board cover, be sure to
remove it opening at a 90-degree angle.
Board cover
Cover/3
A5A9IXC006CB
5. Remove the board cover.
(1) Remove 20 screws of the board cover and pull
open the cover.
Note:
90°
Be sure not to open the board cover at the 90
degrees angle or more.
Board cover
Board cover
A5A9IXC010CB
6. Install the IC-602.
Note:
A5A9IXC007CA Be sure to align the concave part of the IC-602
(2) Unplug 5 connectors and remove the wiring and the concave part of the slot on the control-
harnesses from 3 clamps. ler board when installing the IC-602.
IC-602
Connectors
Clamps
A5A9IXC008CA A5A9IXC011CC
Align the
concave parts
IC-602
E-2
7. Install the memory. (2) Set the board so that the label "FR" of the I/F
Note: cable comes to the position shown in the pic-
• Be sure to Install the memory to the slot 3. ture.
Memory
I/F cable
Label "FR"
A5A9IXC012CB A5XGIXC030CA
(3) Connect 5 connectors and set the wiring har-
nesses in 3 clamps.
Note:
Be sure to connect the wiring harnesses align-
ing the numbers of the wiring harnesses and
the numbers of the board, and set the wiring
harnesses so that they are not floating.
8. Reinstall the board cover.
(1) Fix the board cover with 1 screw. Connectors
Note:
• When reinstalling the board cover, be sure
to align it with the projection.
• Be sure to reinstall the board cover outside
of the main body side.
Clamps
A5XGIXC031CB
Label
"FR"
Board cover
A5A9IXC013CB
(4) Reinstall the board cover. (20 screws)
Board cover 9. Reinstall the cover/3 (2 screws) and reinstall 2
caps.
10.Reinstall the arm cover (Rr). (2 screws)
11.Reinstall the rear cover/2 (17 screws) and the
rear cover/1 (4 screws).
Projection 12.Reinstall the duct cover. (5 screws)
E-3
13. Network connection and setup (2) Network setting initialization
(1) Connect the network cable.
Connect the network cable to the right side of Step
the main body. 1. Turn the main power switch and the sub
Note: power switch ON.
Be sure to use the network cable suited for the 2. Touch the “Utility/Counter” key and then
usage environment. touch the “Administrator Setting” key.
3. Touch the “Network Setting” key.
4. Touch the “NIC Setting” key.
5. Touch the “Detail setting” key.
Network cable 6. Touch the “Next” key 8 times and touch the
“Network Setting Clear” key.
7. Touch the “Start” key.
After the initialization, touch the "Close" key.
8. Turn the sub power switch and the main
power switch OFF first and then turn them
ON.
Note:
A5A9IXC015CA
By turning the sub power switch and the
main power switch OFF first and then
[LED] turning them ON, the setting becomes
Both the NIC (outside) and the Machine NIC enabled.
(inside) have two LEDs (LED1 and LED2), each of
which represent the following conditions. (3) IP address allocation
Note:
LED 1 (top): Displays communication speed • Usually a dedicated administrator handles
Orange (1Gbps) the network and PC environment at the user
Green (100Mbps) end. When conducting the following setup
OFF(10Mbps) procedure, always consult with proper per-
sonnel, get approval, and operate under that
LED 2 (bottom): Displays the link state person’s supervision.
Lighting (Network is connected) • The network settings of the controller have
Blinking (Data transfer state) the DHCP function, however the initial set-
OFF (Network is disconnected) ting is OFF, so make sure to implement net-
work settings.
Step
1. Touch the “Utility/Counter” key and then
touch the “Administrator Setting” key.
2. Touch the “Controller” key.
3. 1. Touch the “Utility/Counter” key and then
touch the “Administrator Setting” key.
2. Touch the “Network Setting” key and then
touch the “NIC Setting” key. Touch the
“TCP/IP Setting” key to set the following
items. After settings are done, touch the
“OK” key.
• IP Address (IP address of the controller)
• Subnet Mask (Subnet Mask for the net-
work)
• Default Gateway (IP address of the
default gateway)
4. After the settings are done, be sure to turn
the Sub power switch and the Main power
switch OFF first and then turn them ON.
(Otherwise the settings will not be regis-
tered. When turning the Main power switch
and the Sub power switch ON, wait for more
than 10 seconds after turning them OFF
before turning them back ON.)
E-4
(4) Print a test copy to check operation
Note:
• Conduct this procedure when using the
Controller NIC.
• Output the required report.
Step
1. Turn the Main and Sub power switches ON.
2. Touch the “Controller” key on the [MACHINE]
screen.
3. Touch the “Report Type” key.
4. Select the type of report.
5. Touch the “Execute” key.
(5) Ping to check network connection.
Note:
Conduct this procedure when using the Con-
troller NIC.
Step
1. Touch the “Utility/Counter” key and then
touch the “Administrator Setting” key.
2. Touch the “Network Setting” key and then
touch the “NIC Setting” key.
3. Touch the “Detail Setting” key, and touch the
“Next” key four times.
On the [PING Confirmation] screen, touch
the “Host Name” key.
4. [Ping Send Address] screen
Enter a valid address, and touch the “OK” key.
5. Touch the “Check Connection” key.
6. Touch the “Start” key.
Check the message.
(1) If OK, <Completed normally> will appear.
(2) If there is a problem, <Error> will
appear.
=> Check if the address is correct and
the network is connected. Resend
again and make sure that the proce-
dure completes successfully.
7. Touch “Close” key and then touch “Exit” key.
E-5
