Request for qoutation.

FIRE PUMP SYSTEM:

Stadard Requirement for Firpump Room.
Compliance
NFPA20 with the below
STANDARDS standard: FIRE PUMPS FOR FIRE
FOR STATIONARY
PROTECTION
FIRE CODE OF THE PHILIPPES' RA 9514 & ITS RIRR
NFPA20 STANDARDS FOR STATIONARY FIRE PUMPS FOR FIRE
PROTECTION
NFPA 25 STANDARDS FOR THE INSPECTION, TESTING, & MAINTENANCE
(ITM) OF WATER BASED FIRE PROTECTION SYSTEM
NFPA 22 STANDARDS FOR FIRE WATER RESEREVE STORAGE
NFPA72 FIRE ALARM & SIGNALING CODE
PHILIPPINE MECHANICAL CODE OF 2012
Sub-Total
STANDARD QTY Unit Matl Cost Labor Cost Amount

GENERAL REQUIREMENTS:
Mobilization N/A 1 Lot
Technical Supervision & Management. N/A 1 Lot
Tools, Equipments/Scaffoldings N/A 1 Lot
Positioning of Equipment at site/Shipment/RIGGING N/A 1 Lot
Temporary Facility N/A 1 Lot
Permits & Licenses: Internal/Local N/A 1 Lot
FIELD ACCEPTANCE TEST/WITNESSED BY OWNER, CONTRACTOR, BFP N/A 1 Lot
Permits & Licenses: Internal/Local, building permit and other related compliances. N/A 1 Lot
Factory Acceptance Test by GMC Representative. N/A 1 Lot

BILL OF QUANTIES.
ENGINE DRIVEN FIRE PUMP, Diesel driven pump, Horizontal Split Case, 2500 GPM, 152.25 psi, 1750 rpm, clockwise, water
1.1 medium, discharge 8 inches, suction 10 inches, Impeller 496 mm, effeciency 70% Maximum HP 357. UL / FM 1 set
1.2 Jockey Pump, Vertical inline, 45 GPM @ 180 psi @ 7.5 HP. UL / FM 1 Set
Controllers for FP & JP Type: GPY (WYE-DELTA), Manufacturer:Tornatech, Rating : HP, Listing :UL-Listed and FM Approved,
1.3 Enclosure: NEMA 2. Shoule be in the same brand with the engine driven pump. UL / FM 1 set

1.4 Standardard Accessories : PRV, Sunction & discharge gauges, Air release valves, Water flowmeters, Standard DIESEL tank, UL / FM 1 lot
1.5 Engine Exhaust System Complete with thermal Insulations, Aluminum Cladding, & Sway brackets for vibrations UL / FM 1 lot
1.6 OTHERS : Delivery of imported Equipments & accessories , rigging, & positioning of equipment/s at site UL / FM 1 lot
1.7 Factory Acceptance Testing, GMC Engineering Represetative. UL / FM 1 lot

PUMP HOUSE CONSTRUCTION & RESERVE TANK PREPARATION per NFPA 20 & 22 Standards

COMPLETE PUMP HOUSE : Steel construction, reinforced, flooring, Epoxy painted with 3 sides concrete (CHB) wall Paint, Finished,
1.8 Naturally Ventilated, Sprinkler protection for Extra, hazard Occupancy, Complete with Lighting & switches NFPA 20 1 lot

1.9 Machine foundation in accordance with the supplied engine driven firepump. Anchor bolts with vibration dampener. Mechanical Code 2012 1 Lot
2 Electrical power supply for the pump room to all the load side of the room. Labor and materials. EE National Standard 1 Lot
2.1 Construction Consumables N/a 1 Lot
PIPES & FITTINGS, MACHINE CONNECTIONS, ACCESSORIES, FOUNDATION, BRACKETS & SUPPORTS TO COMPLETE THE SYSTEM
2.2 ALARM CHECK VALVE, 200MM COMPLETE WITH, ACCESSORIES, Alarm Gong, retard chamber, drain line, In-out UL / FM 1 Set
2.3 Anti Vortex Plates : anti turbulence, 10 inches pipe. NFPA 20 2 Sets
2.4 Pipe Suction Clamps/plates for concrete cylindrical tank UL / FM 1 Lot
2.5 Complete Sensing lines (1-FP & 1-JP): COPPER OR STAINLESS UL / FM 1 Set

PUMP TEST HEADERS & Fire Department Connection

2.6 3 WAY FDC WITH LABEL PLATES 200MM X 65 X 65 X 65 UL / FM 1 Pc
2.7 6-OUTLET PUMP TEST HEADERS WITH LABEL PLATE : 200X65X65X65X65X65X65 UL / FM 1 Set
2.8 FIRELOCK SWING CHECK VALVE: 200MM UL / FM 1 Set

ATSM-53B SCHED 40 PIPELINES & FITTINGS

2.9 250 mm Ø suction line ATSM-53B 18 lm
3 200 mm Ø discharge line ATSM-53B 44 lm
3.1 50 mm Ø ATSM-53B 12 lm

GROOVE COUPLING : VICTAULIC

3.2 250 mm Ø rigid/flex type UL / FM 12 pcs
3.3 200 mm Ø rigid type UL / FM 34 pcs
3.4 200 mm Ø flexible type UL / FM 6 pcs

GROOVE ELBOW : VICTAULIC

3.5 250 X 90 UL / FM 4 pcs
3.6 200 X 90 UL / FM 12 pcs

EQUAL TEE : VICTAULIC

3.7 250 MM UL / FM 2 pcs
3.8 200 MM UL / FM 3 pcs

FLANGE ADAPTOR: VICTAULIC

3.9 250 (PUMP ROOM ACCESSORIES) UL / FM 2 pcs
4 200 (PUMP ROOM ACCESSORIES) UL / FM 3 pcs
4.1 FIRE LOCK CHECK VALVE: VICTAULIC
4.2 200MM UL / FM 2 pcs

PIPES & FITTINGS, MACHINE CONNECTIONS, ACCESSORIES, FOUNDATION, BRACKETS & SUPPORTS TO COMPLETE THE SYSTEM

4.3 OIL, LUBRICANTS, GASKETS, BOLTS & NUTS & ANCHORS, SIDE BRACKETS, OTHERS UL / FM 1 Lot
4.4 SADDLE & SUPPORTS

Pump room Brackets & Supports for Pipelines: Fixed metal with Concrete foundation, 100mm Vertical pipe support, 200mm pipe
saddle & saddle cover with double fixing bolt & nuts, Anchored with 12mm base plates through 4-16mm anchor bolts, complete
with epoxy primer & double top coated paintings: excavation included 200mm G.I. U-bolt sets : Fixed at Pump room UL / FM 1 set

REGULATORY COMPLIANCE
4.5 As Built Plan, Sign and Sealed. 4 Original Copies. 1 Lot
4.6 BFP Installation Clearance 1 Lot
4.7 BFP Inspection 1 Lot
Foot note:
* - Varies on the contractor's design and actual layout.
PUMP ROOM P AND ID.

Other side of the sytem will

be done in next phase.
The Elecric Pump.

See anti vortec plate to be

installed inside the tank.
WAREHOUSE B. SPRIKLER AND FDAS SYSTEM
Stadard Requirement for Fire Mains
FIRE CODE OF THE PHILIPPES' RA 9514 & ITS RIRR
WET TYPE AUTOMATIC FIRE SPRINKLER SYSTEM :
NFPA 13/14 STDS & IN COMPLIANCE WITH RA 9514
Sub-Total
STANDARD QTY Unit Matl Cost Labor Cost Amount
GENERAL REQUIREMENTS:
Mobilization/Demobilization/Inspection-Coordinations 1 Lot
Technical Supervision & Management
Tools, Equipments/Scaffoldings
Provision of Lifting Equipment
Temporary Facility :
Design, Working Plans, As-built Plans Sign & Seal
FIELD ACCEPTANCE TEST

BILL OF MATERIALS

SPRINKLER SYSTEM:

Sprinkler heads shall be recessed, upright, pendent, vertical side wall, horizontal side wall
type as required, 12mm. dia. and/or 13.5mm. dia. orifice, 12mm. dia. and/or 19mm. dia. NFPA 13 and
pipe threads, rated at 68 degrees Centigrade, 93 degrees C, and/or 121 degrees C. 583 Pcs
25
Sprinklers in areas with suspended ceiling the escutcheon plates shall be chrome on center
of the ceiling boards. Sprinkler shall be 93 degrees Centigrade at the Kitchen, Mechanical
room, Genset room and Parking areas with standard orifice glass bulb upright type or
pendent type, and brass finish. Sprinkler shall be 68 degrees Centigrade at the offices and
residential with Quick response orifice glass bulb recessed type, chrome finish UL/FM
Sprinkler K-Factor shall be as per design (see design plans)
 138 meters
30 meters

Area : 4900 sq. meter

 Sub-Total
STANDARD QTY Unit Matl Cost Labor Cost Amount
FIRE HOSE CABINET

Fire Hose Cabinet NFPA 13 8

ATSM-A53B SCHED 40 PIPELINES & FITTINGS: WITH MILL CERTIFICATES 40 mm NFPA 13 8
 Sub-Total
STANDARD QTY Unit Matl Cost Labor Cost Amount

CROSS MAINS AND RISER

All piping shall be supported by means of hangers of approved quality, capable of

supporting load. Sizing, spacing and installation shall be in accordance with
National Fire Protection Association Standard No. 13, “Sprinkler Systems”, except as
otherwise shown on drawings or specified herein.
ATSM-A53B SCHED 40 PIPELINES & FITTINGS: WITH MILL CERTIFICATES NFPA 13, 25
100 mm diameter NFPA 13, 25 380 Meter
Cross main support, 2 inch angle bar, with U bolts mounting. Refer to draft below 1 Lot

Sub-Total
STANDARD QTY Unit Matl Cost Labor Cost Amount

BRANCHLINE . ATSM-A53B SCHED 40 PIPELINES NFPA 13 , 25

ATSM-A53B SCHED 40 PIPELINES
50mm diameter 424 lm
40mm diameter 706 lm
 25mm diameter 1,295 lm

BELL REDUCERS: UL/FM, MECH BRANDS

50mm x 40mm diameter 118 pc
40mm x 25mm diameter 118 pc
25mm x 20mm diameter 589 pc

THREADED ELBOW 90 DEG: UL/FM, MECH BRANDS

50mm diameter 235 pc
25mm diameter 118 pc

THREADED TEE REDUCER: UL/FM, MECH BRANDS

100mm x 50 mm diameter. Mechanical Tee outlet victaulic. 118 pc
50mm x 25mm diameter 118 pc
40mm x 25mm diameter 235 pc

THREADED EQUAL TEE: UL/FM, MECH BRANDS

25mm diameter 235 pc

THREADED END CAP: UL/FM, MECH BRANDS

40mm diameter 8 pc

STANDARD HANGERS & SUPPORTS : LOCAL

Consumables (Weld rods, cutting & grinding discs, paints, ptfe tapes, grease, oils, others) 1 Lot
 Sub-Total
STANDARD QTY Unit Matl Cost Labor Cost Amount
UNIVERSAL FLOOR CONTROL MODULE: UL/FM, VICTAULIC UM assy, 100 MM
FLOOR CONTROL VALVE, C/W

System Sensor Water flow switch

4" dial Face, 300 PSI Pressure gauge
25mm Inspector test & drain valve
Air release module
Sight glass
complete groove connection to Riser drains 1 Set
 FITTING CONSUMBALES, GROOVING CONSUMABLES,
WELDING RODS, GRINDING & CUTTING DISCS, RUST
CONVERTERS & SURFACE PREPARATIONS, EPOXY PRIMERS,
FINAL PAINTINGS, PROTECTION COVERS, PAINT BRUSH 7
ROLLERS, MARKINGS, OTHERS 1 Lot

Sub-Total
STANDARD QTY Unit Matl Cost Labor Cost Amount
FIRE DETECTION AND ALARM CONTROL SYSTSM (FDACS)
Fire Alarm Control Panel (FACP) CONTROLS & DEVICES: UL LISTED/LPCB LISTED
Addressable FACP NFPA 72 1 Sets
Booster Power Supply (BPS) NFPA 72 1 Sets
Addessable Smoke Detector (ASD) NFPA 72 2 Sets
Addressable Manual Pull Station (MCP) NFPA 72 9 Sets
Single Control Module (SCM) NFPA 72 1 Sets
Conventional Horn Strobe NFPA 72 9 Sets
Beam Detector NFPA 72 4 Sets
Beam Refleftor NFPA 72 8 Sets
Addressable input module NFPA 72 7 Sets
Conventional Zone Module NFPA 72 3 Sets
Valve Superviory Switch NFPA 72 3 Sets
Water Flow Switch NFPA 72 3 Sets
End of Line Resistor (EOL) NFPA 72 4 Sets
 Sub-Total
STANDARD QTY Unit Matl Cost Labor Cost Amount

FDACS : WIRES & CABLES /CONDUITS & FITTINGS 1 Lot

Conduits & fittings
Wires & Cables, Twisted pair

FDACS : HANGERS & SUPPORTS/ROUGH-INNS: LOCAL 1 Lot

Roughing-Ins /necessary provisions
Hangers & Supports
 138 meters

30 meters

84 meters 75 meters

14 meters
FIRE MAINS TO WH 25 AND WH B.
Stadard Requirement for Fire Mains
FIRE CODE OF THE PHILIPPES' RA 9514 & ITS RIRR
NFPA 24 STANDARDS FOR THE INSTALLATION OF PRIVATE FIRE SERVICE
MAINS AND THEIR APPURTENANCES
NFPA 25 STANDARDS FOR THE INSPECTION, TESTING, & MAINTENANCE
(ITM) OF WATER BASED FIRE PROTECTION SYSTEM
ASTM STANDARDS

GENERAL REQUIREMENTS:
Mobilization/Demobilization/Inspection-Coordinations
Technical Supervision & Management
Tools, Equipments/Scaffoldings
Provision of Lifting Equipment
Temporary Facility :
Design, Working Plans, As-built Plans Sign & Seal
FIELD ACCEPTANCE TEST/WITNESSED BY OWNER,
CONTRACTOR, BFP

STANDARD QTY Unit Matl Cost Labor Cost Sub-Total

Amount

BILL OF MATERIALS

ATSM-A53B SCHED 40 PIPELINES & FITTINGS: WITH MILL CERTIFICATES

200 mm Ø ATSM-53B 250 lm
150 mm Ø ATSM-53B 150 lm
65 mm Ø ATSM-53B 32 lm
50 mm Ø ATSM-53B 20 lm

FITTING CONSUMBALES, GROOVING CONSUMABLES,

WELDING RODS, GRINDING & CUTTING DISCS, RUST
CONVERTERS & SURFACE PREPARATIONS, EPOXY PRIMERS,
FINAL PAINTINGS, PROTECTION COVERS, PAINT BRUSH 7
ROLLERS, MARKINGS, OTHERS 1 Lot
GROOVE COUPLING : VICTAULIC or UL LISTED/FM
APPROVED.
200 mm Ø rigid type UL / FM 12 pcs
200 mm Ø flexible type UL / FM 2 pcs
150 mm Ø rigid type UL / FM 16 pcs
150 mm Ø flexible type UL / FM 4 pcs
65 mm Ø rigid type UL / FM 6 pcs
GROOVE TEE reducer : VICTAULIC UL LISTED/FM
APPROVED
200 X 150 mm Ø UL / FM 4 pcs
GROOVE ELBOW : VICTAULIC UL LISTED or FM
APPROVED
200 X 90 UL / FM 8 pcs
200 X 45 UL / FM 4 pcs
150 X 90 UL / FM 10 pcs
150 x 45 UL / FM 1 pcs
65 X 90 UL / FM 4 pcs

OS & Y GATEVALVE: VICTAULIC UL LISTED/FM

APPROVED
150MM : RISER PROVN FOR BUILDINGS UL / FM 4 pcs

EQUAL TEE : UL LISTED/FM APPROVED

200 MM UL / FM 1 pcs
150 MM UL / FM 1 pcs

GROOVE & WELDED FITTINGS : UL LISTED/FM

APPROVED
BI ELBOW, 200 X 90 WELDED UL / FM 2 pcs
SOF, 200MM, 300 PSI UL / FM 2 pcs
BLIND FLANGE, 200MM, 300 PSI UL / FM 2 pcs
 OIL, GASKETS, BOLTS & NUTS & ANCHORS, SIDE BRACKETS,
OTHERS N/A 1 Lot

SADDLE S & SUPPORTS

Overhead & Fixed Wall Brackets & Rigid Supports fixed with 12-
16mm U bolts: Crossing WH25 to WB 1 Lot

Painting Works. Sanding, rust converters, primer application, double coating. 1 Lot

HYDRANTS & STAND PIPES FOR WB 25 & WH B

ATSM-A53B SCHED 40 PIPELINES & FITTINGS

65 mm Ø ATSM-A53B 24 lm

FITTING CONSUMBALES, GROOVING CONSUMABLES,

WELDING RODS, GRINDING & CUTTING DISCS, RUST
CONVERTERS & SURFACE PREPARATIONS, EPOXY PRIMERS,
FINAL PAINTINGS, PROTECTION COVERS, PAINT BRUSH 7
ROLLERS, MARKINGS, OTHERS N/A 1 Lot
GROOVE COUPLING : VICTAULIC UL LISTED/FM
APPROVED
200 X 65 mm Ø rigid type UL LISTED UL / FM 6 pcs
GROOVE ELBOW : VICTAULIC UL LISTED/FM
APPROVED
65 X 90 UL / FM 12 pcs
FLANGE ADAPTOR: VICTAULIC UL LISTED/FM
APPROVED
65MM (HYDRANT CONNECTION) UL / FM 6 pcs
FITTINGS & INSTALLATION CONSUMABLES
OIL, GASKETS, BOLTS & NUTS, SIDE BRACKETS, OTHERS 1 Lot
HYDRANTS & ACCESSORIES : LISTED & FM APPROVED

Stand post Type Fire Hydrant – Double Outlet• 600 mm high

X 100 mm (4”) NB flanged inlet.• Carbon Steel post, with
double outlets of dia. 3” N.B. flanged.• Complete with two FM
approved oblique type fire hydrant valves (NI 101) -single
Oblique outlet, made of Gunmetal having 3” N.B. flanged inlet
& 2.1/2”female instantaneous oblique type outlet as per BS:
336, complete with brassspindle, ABS blank cap & SS chain.•
Set of Nut Bolts and Gasket for each Hydrant will be
provided.• Flange drilling dimension will be as per ANSI B 16.5
Class 150 FF UL / FM 6 pcs

Fire Hydrant Valve, Single Oblique Outlet [NI101]• Body made

of Gunmetal.• 3" N.B. Flanged inlet (FF) & 2.1/4” male BSP
Threaded type outlet.• Spindle made of Brass and C.I Hand
wheel.• Conforming to BS:5041• Flange Dimensions as per
ANSI B 16.5 Class 150• FM Approved.Complete with extra
adaptor• Body made of Gunmetal.• Having Size of 2.1/4”
Female BSP Threaded X 2.1/2” Female NH Threadedadaptor•
Complete with Gunmetal 2.5” male NH threaded blank cap &
SS chain UL / FM 6 pcs

Hydrant Valve, Single Oblique Outlet [NI101]• Body made of

Gunmetal.• 3" N.B. Flanged inlet (FF) & 2.1/4” male BSP
Threaded type outlet.• Spindle made of Brass and C.I Hand
wheel.• Conforming to BS:5041• Flange Dimensions as per
ANSI B 16.5 Class 150• FM Approved.Complete with extra
adaptor• Body made of Gunmetal.• Having Size of 2.1/4”
Female BSP Threaded X 1.1/2” Female NH Threadedadaptor•
Complete with Gunmetal 1.5” male NH threaded blank cap &
SS chain UL / FM 6 pcs
NewAge Make “PREMIER DJ” Brand Fire Double Jacket Hose
With Coupling• Double jacket fire hose for extra strength.•
High burst pressure.• UL LISTED @300 PSI• Fire Hose Dia.
2.1/2” X 15 Mtrs• EPDM/Synthetic rubber lined.• Hard wearingresistant
to abrasions, oil & chemicals• Manufactured under
strict ISO: 9001 Quality system.• White in color• Complete with
Aluminum alloy Coupling of dia. 2.1/2" x 2.1/2" NH
threadedrocker lug male & female couplings with expansion
ring UL / FM 6 pcs

NewAge Make “PREMIER DJ” Brand Fire Double Jacket Hose

With Coupling• Double jacket fire hose for extra strength.•
High burst pressure.• UL LISTED @300 PSI• Fire Hose Dia.
1.1/2” X 15 Mtrs• EPDM/Synthetic rubber lined.• Hard wearingresistant
to abrasions, oil & chemicals• Manufactured under
strict ISO: 9001 Quality system.• White in color• Complete with
Aluminum alloy Coupling of dia. 1.1/2" x 1.1/2” NH
threadedrocker lug male & female couplings with expansion
ring UL / FM 6 pcs
Jet & Spray Nozzle (NEWAGE NZ 65)• Made of Brass• 2.5”
Female NH threaded inlet• UL Listed UL / FM 6 pcs
Jet & Spray Nozzle (NEWAGE NZ 38)• Made of Brass• 1.5”
Female NH threaded inlet• UL Listed UL / FM 6 pcs
Hydrant Wrench UL / FM 6 pcs

Wrench(HS code: 84249000)

FIREMAN AXE• Made of carbon steel with rubber insulated
handle tested to 20,000 Volts UL / FM 6 pcs
COMPLETE OUTDOOR FIRE HOSE CABINET, COMPLETE
WITH HOSE RACKS, HANDLES, FIXED MOUNTED with RIGID UL / FM 6 pcs
OIL, GASKETS, BOLTS & NUTS, BRACKETS, PRIMER, PAINTS n/a 1 Lot
 Branchline details

Bell reducer 25 x 20 mm.

Bell Reducer 50 mm x 40 mm
Bell Reducer 40 mm x 25 mm
Elbow 50 x 50 mm 90 deg
Elbow 90 deg 25x25
Pipe 25 mm
Pipe 40 mm
Pipe 50 mm dia branch riser
Sprinkler
Tee 100mm x 50 mm _Victaulic
Tee 25x25x25
Tee 40x40x25
Tee 50 mm x 50 mm x 25
 Purpose Qty in 1 set Unit No of branchline

25 mm pipe head to sprinkler. 5 pcs 107

Reduce to 40 mm for 2nd and 3rd segment 1 pc 107
Reduce to 25 mm for 4nd and 5th segment 1 pc 107
2 bends. 2 107
5ht sprinkler 1 pcs 107
sprinkler pipe, 4ht and 5th segment 11 lm 107
2nd and 3rd segment 6 lm 107
Branch 1st segment pipe size 3.6 lm 107
Fire suppression 5 pc 107
Cross main to branch line 1 107
4th sprinkler 1 pc 107
2 and 3rd sprinkler 2 pc 107
1 sprinkler, 4ht and 5th segment. 1 pcs 107
Total Needed Allowance

535 589
107 118
107 118
214 235
107 118
1177 1295
642 706
385.2 424
535 589
107 118
107 118
214 235
107 118
FIRE MAINS TO WH 25 AND WH B.
Stadard Requirement for Fire Mains

GENERAL REQUIREMENTS:

BILL OF MATERIALS
HYDRANTS & STAND PIPES FOR WB 25 & WHB
FIRE MAINS TO WH 25 AND WH B.
Stadard Requirement for Fire Mains
FIRE CODE OF THE PHILIPPES' RA 9514 & ITS RIRR
NFPA 24 STANDARDS FOR THE INSTALLATION OF PRIVATE FIRE SERVICE
MAINS AND THEIR APPURTENANCES
NFPA 25 STANDARDS FOR THE INSPECTION, TESTING, & MAINTENANCE
(ITM) OF WATER BASED FIRE PROTECTION SYSTEM
ASTM STANDARDS

GENERAL REQUIREMENTS:
Mobilization/Demobilization/Inspection-Coordinations
Technical Supervision & Management
Tools, Equipments/Scaffoldings
Provision of Lifting Equipment
Temporary Facility :
Design, Working Plans, As-built Plans Sign & Seal
FIELD ACCEPTANCE TEST/WITNESSED BY OWNER,
CONTRACTOR, BFP

STANDARD

BILL OF MATERIALS

ATSM-A53B SCHED 40 PIPELINES & FITTINGS: WITH MILL CERTIFICATES

200 mm Ø ATSM-53B
150 mm Ø ATSM-53B
65 mm Ø ATSM-53B
50 mm Ø ATSM-53B

FITTING CONSUMBALES, GROOVING CONSUMABLES,

WELDING RODS, GRINDING & CUTTING DISCS, RUST
CONVERTERS & SURFACE PREPARATIONS, EPOXY PRIMERS,
FINAL PAINTINGS, PROTECTION COVERS, PAINT BRUSH 7
ROLLERS, MARKINGS, OTHERS
GROOVE COUPLING : VICTAULIC or UL LISTED/FM
APPROVED / OR Welding works.(* Applicable if using victaulic)
200 mm Ø rigid type UL / FM
200 mm Ø flexible type UL / FM
150 mm Ø rigid type UL / FM
150 mm Ø flexible type UL / FM
65 mm Ø rigid type UL / FM
 GROOVE TEE reducer : VICTAULIC UL LISTED/FM
APPROVED
200 X 150 mm Ø UL / FM
GROOVE ELBOW : VICTAULIC UL LISTED or FM
APPROVED
200 X 90 UL / FM
200 X 45 UL / FM
150 X 90 UL / FM
150 x 45 UL / FM
65 X 90 UL / FM

OS & Y GATEVALVE: VICTAULIC UL LISTED/FM

APPROVED
150MM : RISER PROVN FOR BUILDINGS UL / FM

EQUAL TEE : UL LISTED/FM APPROVED

200 MM UL / FM
150 MM UL / FM

GROOVE & WELDED FITTINGS : UL LISTED/FM

APPROVED
BI ELBOW, 200 X 90 WELDED UL / FM
SOF, 200MM, 300 PSI UL / FM
BLIND FLANGE, 200MM, 300 PSI UL / FM

OIL, GASKETS, BOLTS & NUTS & ANCHORS, SIDE BRACKETS,

OTHERS N/A

SADDLE S & SUPPORTS

Overhead & Fixed Wall Brackets & Rigid Supports fixed with 12-
16mm U bolts: Crossing WH25 to WB

Painting Works. Sanding, rust converters, primer application, double coating.

HYDRANTS & STAND PIPES FOR WB 25 & WHB

ATSM-A53B SCHED 40 PIPELINES & FITTINGS

65 mm Ø ATSM-A53B

FITTING CONSUMBALES, GROOVING CONSUMABLES,

WELDING RODS, GRINDING & CUTTING DISCS, RUST
CONVERTERS & SURFACE PREPARATIONS, EPOXY PRIMERS,
FINAL PAINTINGS, PROTECTION COVERS, PAINT BRUSH 7
ROLLERS, MARKINGS, OTHERS N/A
GROOVE COUPLING : VICTAULIC UL LISTED/FM
APPROVED
200 X 65 mm Ø rigid type UL LISTED UL / FM
GROOVE ELBOW : VICTAULIC UL LISTED/FM
APPROVED
65 X 90 UL / FM
FLANGE ADAPTOR: VICTAULIC UL LISTED/FM
APPROVED
65MM (HYDRANT CONNECTION) UL / FM
FITTINGS & INSTALLATION CONSUMABLES
OIL, GASKETS, BOLTS & NUTS, SIDE BRACKETS, OTHERS
HYDRANTS & ACCESSORIES : LISTED & FM APPROVED

Stand post Type Fire Hydrant – Double Outlet• 600 mm high

X 100 mm (4”) NB flanged inlet.• Carbon Steel post, with
double outlets of dia. 3” N.B. flanged.• Complete with two FM
approved oblique type fire hydrant valves (NI 101) -single
Oblique outlet, made of Gunmetal having 3” N.B. flanged inlet
& 2.1/2”female instantaneous oblique type outlet as per BS:
336, complete with brassspindle, ABS blank cap & SS chain.•
Set of Nut Bolts and Gasket for each Hydrant will be
provided.• Flange drilling dimension will be as per ANSI B 16.5
Class 150 FF UL / FM

Fire Hydrant Valve, Single Oblique Outlet [NI101]• Body made

of Gunmetal.• 3" N.B. Flanged inlet (FF) & 2.1/4” male BSP
Threaded type outlet.• Spindle made of Brass and C.I Hand
wheel.• Conforming to BS:5041• Flange Dimensions as per
ANSI B 16.5 Class 150• FM Approved.Complete with extra
adaptor• Body made of Gunmetal.• Having Size of 2.1/4”
Female BSP Threaded X 2.1/2” Female NH Threadedadaptor•
Complete with Gunmetal 2.5” male NH threaded blank cap &
SS chain UL / FM

Hydrant Valve, Single Oblique Outlet [NI101]• Body made of

Gunmetal.• 3" N.B. Flanged inlet (FF) & 2.1/4” male BSP
Threaded type outlet.• Spindle made of Brass and C.I Hand
wheel.• Conforming to BS:5041• Flange Dimensions as per
ANSI B 16.5 Class 150• FM Approved.Complete with extra
adaptor• Body made of Gunmetal.• Having Size of 2.1/4”
Female BSP Threaded X 1.1/2” Female NH Threadedadaptor•
Complete with Gunmetal 1.5” male NH threaded blank cap &
SS chain UL / FM
NewAge Make “PREMIER DJ” Brand Fire Double Jacket Hose
With Coupling• Double jacket fire hose for extra strength.•
High burst pressure.• UL LISTED @300 PSI• Fire Hose Dia.
2.1/2” X 15 Mtrs• EPDM/Synthetic rubber lined.• Hard wearingresistant
to abrasions, oil & chemicals• Manufactured under
strict ISO: 9001 Quality system.• White in color• Complete with
Aluminum alloy Coupling of dia. 2.1/2" x 2.1/2" NH
threadedrocker lug male & female couplings with expansion
ring UL / FM

NewAge Make “PREMIER DJ” Brand Fire Double Jacket Hose

With Coupling• Double jacket fire hose for extra strength.•
High burst pressure.• UL LISTED @300 PSI• Fire Hose Dia.
1.1/2” X 15 Mtrs• EPDM/Synthetic rubber lined.• Hard wearingresistant
to abrasions, oil & chemicals• Manufactured under
strict ISO: 9001 Quality system.• White in color• Complete with
Aluminum alloy Coupling of dia. 1.1/2" x 1.1/2” NH
threadedrocker lug male & female couplings with expansion
ring UL / FM
Jet & Spray Nozzle (NEWAGE NZ 65)• Made of Brass• 2.5”
Female NH threaded inlet• UL Listed UL / FM
Jet & Spray Nozzle (NEWAGE NZ 38)• Made of Brass• 1.5”
Female NH threaded inlet• UL Listed UL / FM
Hydrant Wrench UL / FM

Wrench(HS code: 84249000)

FIREMAN AXE• Made of carbon steel with rubber insulated
handle tested to 20,000 Volts UL / FM
COMPLETE OUTDOOR FIRE HOSE CABINET, COMPLETE
WITH HOSE RACKS, HANDLES, FIXED MOUNTED with RIGID UL / FM
OIL, GASKETS, BOLTS & NUTS, BRACKETS, PRIMER, PAINTS n/a
 Sub-Total
QTY Unit Matl Cost Labor Cost Amount

250 lm
150 lm
32 lm
20 lm

1 Lot

12 pcs
2 pcs
16 pcs
4 pcs
6 pcs
4 pcs

8 pcs
4 pcs
10 pcs
1 pcs
4 pcs

4 pcs

1 pcs
1 pcs

2 pcs
2 pcs
2 pcs

1 Lot

1 Lot

1 Lot

Fire Mains to
WH 25.
24 lm 85 M

1 Lot RAIN
WATER
TANK
 RAIN
WATER
TANK

6 pcs

12 pcs

6 pcs

6 pcs

6 pcs

6 pcs
6 pcs

6 pcs

6 pcs

6 pcs
6 pcs

6 pcs Rain water collection tank

6 pcs dia 30
1 Lot Radius 15 m
Height 4
3.1416
area 706.86 sq. meter
Vol 2827.44 Cu. Meter
2500
 WH B

WH 25
Fire
Mains to
WH B.
65 m

Fire
Pump
RAIN Room
WATER
TANK
 Fire
Pump
RAIN Room
WATER
TANK
General Project Gantt Chart
Objective: FSIC Compliance for 2025 commitment.

1 Site preparations:
1.1 Rehabilitation of Rain water collection tank.
1.1.1 Drain water
1.1.2 Cleaning of debris
1.1.3 Epoxy Coating.
1.1.4 Installation of net cover
1.1.5 Installation of 4" Stub out pipe for boiler use.
1.1.6 Installation of 10" discharge pipes 2 units with anti Vortex
2 Project Proper.
2.1 Fire Pump acquisition. (Could be short as 2 Months). Often make to order.

2.2 Fire Pump Room construction.

2.2.1 Fire pump room piping system.
2.2.2 Installation of Fire pump

2.3 Fire Mains to WH B and WH 25. (Commonly term as hydrant line).

2.4 Hydrant System & Sprinkler System Installation in Ware House B.

Note: Project can run simultaneously if needed. The project lead time may v
 Lead Time
Weeks 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
Month 1 2 3 4 5 6

for boiler use.

pes 2 units with anti Vortex

2 Months). Often make to order.

ly term as hydrant line).

ation in Ware House B.

eded. The project lead time may vary from 5 Months to 9 Months of construction from the date of PO release.
Not a critical for the project.
Project time line.
22 23 24
6
Fire Protection:
https://flameguardph.com/

Fire Pumps
https://www.youtube.com/watch?v=hdBO_yhNOJg
ch?v=hdBO_yhNOJg