Teldat S.A.

Manual

Teldat Connect-FW

Installation Manual

Copyright© Teldat Dm1045-I Version 1.2 10/2022 Teldat S.A.

Teldat Connect-FW 1
Manual Teldat S.A.

Legal Notice

Warranty

This publication is subject to change.

Teldat S.A. offers no warranty whatsoever for information contained in this manual.

Teldat S.A. is not liable for any direct, indirect, collateral, consequential or any other damage connected to the deliv-
ery, supply or use of this manual.

2 Teldat Connect-FW
Teldat S.A. Table of Contents

Table of Contents

I Related Documents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Chapter 1 About this Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1.1 Supported devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1.2 Who should read this manual? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1.3 When should this manual be read? . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1.4 What is in this manual? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1.5 What is not in this manual? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1.6 How is the information organized? . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1.7 Technical support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Chapter 2 Teldat Connect-FW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2.1 Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2.1.1 Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2.1.2 Hardware monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Chapter 3 Components and Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3.1 Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3.1.1 Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3.1.2 Underside panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3.2 Mounting an anti-theft security cable . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3.3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3.3.1 Standalone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3.3.2 Wall mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3.3.3 19'' Rack installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.4 Power source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3.5 RST button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.5.1 Rebooting the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.5.2 Default configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.6 Data connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3.6.1 4-port Ethernet switch connections . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3.6.2 WAN Combo connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3.6.3 WAN 2.5G connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3.6.4 Wireless LAN internal antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3.6.5 Connecting for configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Teldat Connect-FW i
Table of Contents Teldat S.A.

Chapter 4 Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

4.1 Manufacturer information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

4.2 Risk identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

4.3 Safety warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

4.4 WEEE information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4.5 REACH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4.6 Power usage and energy efficiency . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4.7 PSU energy efficiency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4.8 EC declaration of conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

4.9 CE marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

4.10 National restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

4.11 Operating frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

4.12 Intended use of the equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Appendix A Technical Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

A.1 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

A.2 Updating the software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

A.3 Connecting to the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

A.3.1 Connecting using the local console (AUX connector) . . . . . . . . . . . . . . . . . . . 20

A.4 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

A.4.1 LAN connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

A.4.2 WAN Base-T connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

A.4.3 WAN SFP connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

A.4.4 Configuration connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

A.4.5 Power supply connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

A.5 Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

A.5.1 Hardware architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

A.5.2 LAN interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

A.5.3 WAN Base-T interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

A.5.4 WAN SFP interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

A.5.5 Wireless LAN interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

A.5.6 Configuration interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

A.5.7 Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

A.5.8 Dimensions and weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

A.5.9 Environmental specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Appendix B CE Radio Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

ii Teldat Connect-FW
Teldat S.A. Table of Contents

B.1 WI-FI specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Teldat Connect-FW iii

Teldat S.A. Related Documents

I Related Documents
Teldat Dm704-I Configuration and Monitoring

Teldat Dm709-I LAN interfaces

Teldat Dm748-I Software Updating

Teldat Dm771-I Wireless LAN Interface.

Teldat Connect-FW 1
1 About this Guide Teldat S.A.

Chapter 1 About this Guide

This is the installation manual for the Teldat Connect-FW router and contains information on how to correctly install
the device in a working environment.

1.1 Supported devices

The information provided in this installation manual only applies to the Teldat Connect-FW router.

1.2 Who should read this manual?

This manual should be read by support personnel who need to configure, maintain and monitor the device.

1.3 When should this manual be read?

Read this guide as soon as you are ready to familiarize yourself with the device and its components.

This manual will help you understand your new device in greater depth.

1.4 What is in this manual?

This installation guide contains the following information:

• A description of the features available in the Teldat Connect-FW router.

• Technical specifications.
• Power supply requirements.
• Elements that can be connected when the router is operating.
• How to install and uninstall the modules and power sources.
• A description of the LEDs and connectors in the device.
• Troubleshooting.

1.5 What is not in this manual?

This manual does not contain information on software or device configuration. For details on how to configure the
device, please see the relevant protocol manuals found on the Teldat website: http://www.teldat.com

1.6 How is the information organized?

Each chapter focuses on a specific part of the hardware and its components. All descriptive and technical specifica-
tions, as well as the information on a given component, can be found in the relevant chapter.

1.7 Technical support

Teldat S.A. offers technical support. Device software can be upgraded on a regular basis for maintenance purposes
and in case new features are developed.

Contact information:

Web: http://www.teldat.com - Email: [email protected]

Tel.: +34 918 076 565 - Fax: +34 918 076 566

2 Teldat Connect-FW
Teldat S.A. 2 Teldat Connect-FW

Chapter 2 Teldat Connect-FW

Fig. 1: Teldat Connect-FW

2.1 Characteristics

2.1.1 Power supply

For further information on the different Teldat Connect-FW power supplies, please see Components and Power
Supply on page 4, Power source on page 10.

2.1.2 Hardware monitoring

The LEDs on the front panel are used to monitor the hardware in the Teldat Connect-FW router. These LEDs
provide visual information on the state of the device and reference the condition of the hardware components, indic-
ating whether or not there is connectivity, data flow, etc.

For further information on the LED panel, please see Components on page 4.

Teldat Connect-FW 3
3 Components and Power Supply Teldat S.A.

Chapter 3 Components and Power Supply

The following chapter provides detailed information on the chassis of the Teldat Connect-FW router and its compon-
ents. This information includes:

• Components.
• Information on assembly.
• Power supply.
• RST button.
• Data connection.
• SIM card installation.

3.1 Components

3.1.1 Front panel

The following figure shows the front panel. Here you will find the majority of Teldat Connect-FW router connectors.

Fig. 2: Front panel

The following table provides information on each connector, as well as a description:

Front panel components

Item Description

A Eth WAN-1 SFP.

For more information on the SFP interface, refer to:

- WAN Combo connection on page 12

- WAN SFP connector on page 22

- WAN SFP interface on page 24

B Eth WAN-1 Base-T. WAN Gigabit Ethernet.

For more information on the WAN interface, refer to:

- WAN Combo connection on page 12

- WAN Base-T connectors on page 22

- WAN Base-T interface on page 23

C Eth WAN-2 Base-T. WAN 2.5 Gigabit Ethernet.

For more information on the WAN interface, refer to:

- WAN 2.5G connection on page 13

- WAN Base-T connectors on page 22

- WAN Base-T interface on page 23

4 Teldat Connect-FW
Teldat S.A. 3 Components and Power Supply

D 4-port Gigabit Ethernet Switch (LAN1 to LAN4).

For more information on the LAN interface, refer to:

- 4-port Ethernet switch connections on page 12

- LAN connectors on page 21

- LAN interface on page 23

E LED PWR (Power). Refer to on page for more information.

F LED WLAN (WLAN Status). Refer to LEDs on page 5 for more information.

G RST. Reset button. For further information on how the reset button works, please
see RST button on page 11.

H Aux. Provides access to the Teldat Connect-FW local console for configuration
and monitoring purposes.

For more information on the Aux connector, refer to:

- Connecting for configuration on page 13

- Configuration connector on page 22

- Configuration interface on page 26

I Power source connection (DC IN).

Refer to Power source on page 10 for more information on Power connection and
Power supply on page 26 for power specifications applicable to the Teldat Con-
nect-FW device.

J Kensington security slot

For further information, please see on page

In addition to the foregoing, the front panel also has LEDs linked to the LAN and WAN Ethernet interfaces.

3.1.1.1 LEDs

The following figure shows the router's WAN-1 LED indicators:

Fig. 3: WAN-1 LEDs

WAN-1 Ethernet LED indicators

LED Description
Copper status
Green
- Steady: 10/100/1000M link established.

- Blinking: Transferring data.

Yellow Fiber status:

- Steady: 1000M link established.

Teldat Connect-FW 5
3 Components and Power Supply Teldat S.A.

None Interface is either unavailable, not installed, or not registered.

The following figure shows the router's WAN-2 LED indicators:

Fig. 4: WAN-2 LEDs

WAN-2 2.5G Ethernet LED indicators

LED Description
Yellow
- Steady: 10/100M link established.

- Blinking: Transferring data.

Yellow+Green - Steady: 1000M link established.

- Blinking: Transferring data

Green - Steady: 2.5G link established.

- Blinking: Transferring data

None Interface is either unavailable, not installed, or not registered.

The following figure shows the router's Ethernet switch LED indicators:

Fig. 5: Switch LEDs

Switch LED indicators

LED Description

Yellow Connected to 10/100 M:

- Steady: Not transferring data.

- Blinking: Transferring data.

Yellow + Green Connected to 1000 M:

- Steady: Not transferring data.

- Blinking: Transferring data.

6 Teldat Connect-FW
Teldat S.A. 3 Components and Power Supply

None The interface is either unavailable, not installed or not registered.

In addition, the Teldat Connect-FW is equipped with two status LEDs

LEDs

LED Status Description

PWR Monochrome green Green -> Device powered.

WLAN Tricolor Green -> Some client connected and registered in one of two ra-
dios. Blinking: Transferring data.

Amber -> Interface enabled.

Red -> Interface down.

Off -> Interface off or disabled.

3.1.2 Underside panel

The following elements can be found on the underside panel:

Fig. 6: Underside panel

The following table contains details on the relevant elements found on the underside panel.
Underside panel elements

Item Description

A Rubber feet.

B Slots for wall mounting.

For further information, please see Wall mounting on page 8.

C Holes for rack mounting.

For further information, please see 19'' Rack installation on page 9.

3.2 Mounting an anti-theft security cable

Teldat Connect-FW devices have been equipped with a standard Kensington security slot for attaching a security
cable. The T-bar lock of the security cable allows the device to be attached to an anchor point, thus preventing po-
tential thefts.

The security slot is located on the front panel of the housing, as shown in the following figure:

Teldat Connect-FW 7
3 Components and Power Supply Teldat S.A.

Fig. 7: Security Slot

3.3 Installation

3.3.1 Standalone
Teldat Connect-FW devices can be placed as standalone on a flat, stable surface.

Make sure there is enough space around the router (for ventilation purposes) and check that the power cord and
data cables can easily reach it.

Workplace conditions. Main characteristics:

• Avoid humid and/or dusty locations.

• Direct exposure to sunlight and other heat sources should be avoided. The device should not be placed amongst
papers, magazines or other elements that could hinder natural air circulation.
• The device should not be placed close to strong electromagnetic fields (such as speakers, engines, etc.).
• Knocks and/or strong vibrations should be avoided during transport, operation and storage.

3.3.2 Wall mounting

The Teldat Connect-FW can be mounted on the wall.

There are two slots on the underside of the device that allow it to be fixed to the wall.

We recommend the following accessories for wall mounting, valid for solid and Gypsum board (plaster) walls:

• 2 screws: [3.5x30 mm coach screw with a 90-degree head angle].

Fig. 8: Screw

• 2 wall anchors: [8 mm diameter white ribbed wall anchor].

Fig. 9: Wall anchor

Warning

The screws must go into a wall stud (wood) or a wall anchor of the appropriate type for the wall. Screws
into drywall are not strong enough to mount the router.

8 Teldat Connect-FW
Teldat S.A. 3 Components and Power Supply

Warning

Make sure that there are no concealed pipes and cables at the desired drilling location before drilling
any mounting holes. Damage to electricity cables, gas, water and sewage pipes can result in death or
material damage. Choose the installation location so that as few obstacles or electrical appliances as
possible disturb the connection.

Note

The screws and wall anchors are not delivered with the router.

The following figure shows the two slots on the underside of the device that can be used to fix it to the wall:

To mount the router on a wall or another surface, follow these steps:

Procedure

Step 1. Align the two screws (3.5x30 mm) horizontally on a wall (or any other vertical surface) and install them 116.5
mm (4.56 inches) apart.

The screws should protrude 6 mm (0.25 inch) from the wall surface.

Warning

If you are installing the screws into drywall, use hollow wall anchors (8 mm – 5/16 inch) to secure the
screws. If the screws are not properly anchored, the strain of the cables connected to the router's back
panel could pull the router from the wall.

Step 2. Hang the router on the screws.

3.3.3 19'' Rack installation

The Teldat Connect-FW device can be installed in a 19” rack.

Note

The rack mount kit, composed of strips and screws, is not delivered by default with the router and must
be acquired separately.

Teldat Connect-FW 9
3 Components and Power Supply Teldat S.A.

Fig. 11: Rack installation

Both strips are attached to the device by means of 4 screws, as shown in the following figure:

Fig. 12: Rack anchor bolts

Note

The device has been designed to allow brackets to be attached to the front or rear of the router
chassis.

3.4 Power source

The Teldat Connect-FW router is powered through an external AC/DC power adapter.

10 Teldat Connect-FW
Teldat S.A. 3 Components and Power Supply

Warning

The equipment must be used with the power supply provided by the manufacturer.

To power the router, plug the power supply into the mains supply and the DC connector.

Fig. 13: DC Connector

To avoid electric shocks, residual current circulation, and other unwanted effects that also affect communications, the
following is recommended:

Warning

All interconnected communication devices should be plugged into THE SAME GROUNDED POWER
OUTLET, which should at the same time be of good quality (lower than 10 ohms).

We recommend connecting all data devices to the same power source regardless of whether the work-
place has an uninterrupted power supply system (UPS), a regulated supply or is independent of other
power supplies (such as lighting, etc.). This will help to prevent malfunctions and premature aging of
the drivers and other components.

3.5 RST button

The different RST button features are described below.

Fig. 14: RST button

3.5.1 Rebooting the device

Once the device is operating normally, pressing the RST button will force a restart.

3.5.2 Default configuration

The RST button allows you to boot the device with its default configuration through the following steps:

• With the device switched off, keep the RESET button pressed until the device switches on.
• The PWR (green) will light up and the WLAN LED will begin to blink in yellow. This blinking will continue for 10
seconds.
• For the device to boot with the default configuration, release the Reset button while the WLAN LED is blinking (i.e.,
before the 10-second period expires).

Once the default configuration is running, the router's default configuration establishes the following access IP and
mask address:

• IP address: 192.168.0.1
• IP mask: 255.255.255.0

Teldat Connect-FW 11
3 Components and Power Supply Teldat S.A.

Note

Some devices leave the factory with customized settings. This personalization means your router's de-
fault configuration (and that of the embedded access point, where applicable) may be different from the
one shown above.

3.6 Data connections

The Teldat Connect-FW router has the following data connections.

3.6.1 4-port Ethernet switch connections

The Teldat Connect-FW router incorporates a 4-port 10/100/1000 Base-T switch with automatic MDI/MDIX to con-
nect to a local area network (LAN).

Please pay careful attention to the labeling to avoid mistaking this switch for other types of ports:

Fig. 15: LAN ports

Note

Only the LAN 1 connector is available during booting and in BIOS mode.

3.6.2 WAN Combo connection

The Teldat Connect-FW has one combo Gigabit Ethernet interface for WAN connection. This port has 2 connectors
- SFP for an optical link and RJ45 for a 10/100/1000 Base-T link - but they cannot work simultaneously.

Please pay careful attention to the labeling to avoid mistaking these ports for other types of ports:

Fig. 16: WAN Combo connector

Note

This WAN interface has a UTP/Fiber Media Auto Detection feature.

Only one of the connectors must be used for proper operability.

Note

WAN-1 connector does not work during booting and in BIOS mode.

Note

An appropriate software license may be required for the combo WAN (WAN-1) interface to work.

12 Teldat Connect-FW
Teldat S.A. 3 Components and Power Supply

3.6.2.1 Laser information

Choose SFP transceivers that meet the following regulations

• Class 1
• IEC/EN60825-1:2007 2nd Edition or a later one, European standard
• FCC 21 CFR Chapter 1, Subchapter J (in accordance with FDA and CDRH re-
quirements)
• Application of CE marking in accordance with the 2014/30/EU EMC Directive
and the 2014/35/EU Low Voltage Directive
• UL and/or CSA registered component for North America
• 47 CFR Part 15, Class A

Warning

Laser Radiation. Do not use optical instruments directly or without proper protection. CLASS 1 LASER
PRODUCT.

The SFP modules to be installed in the card socket should be class 1 devices that comply with the IEC/
EN 60825-1:2007 standard.

3.6.3 WAN 2.5G connection

The Teldat Connect-FW has one 2.5 Gigabit Ethernet interface for WAN connection. This port has an RJ45 for a
10/100/1000/2500 Base-T link with automatic MDI/MDIX detection.

Please pay careful attention to the labeling to avoid mistaking these ports for other types of ports:

Fig. 17: WAN 2.5G connector

Note

WAN-2 connector does not work during booting and in BIOS mode.

3.6.4 Wireless LAN internal antennas

The Teldat Connect-FW has two integrated antennas for a Wireless LAN module covering both the 2.4 GHz and 5
GHz bands.

The WLAN module is internal and is only available for the Wi-Fi models.

3.6.5 Connecting for configuration

The Teldat Connect-FW router has an RJ45 female connector on the front panel (labeled "AUX.") that provides ac-
cess to the device's local console.

For further information, please see Connecting to the device on page 20.

Teldat Connect-FW 13
3 Components and Power Supply Teldat S.A.

Fig. 18: AUX. Connector

14 Teldat Connect-FW
Teldat S.A. 4 Compliance

Chapter 4 Compliance

4.1 Manufacturer information

Brand Teldat

Manufacturer Teldat S.A.

Country Spain

Postal Address Isaac Newton, 10

Parque Tecnológico de Madrid, 28760

Tres Cantos, Madrid, Spain

International Phone +34 91 807 65 65

4.2 Risk identification

WARNING: Signal word used to designate a potentially dangerous situation that
may cause severe injuries or death if not avoided.

4.3 Safety warnings

                  

           !       

"              #         

$     "%&  '  (              

   

) *  +   "%,+-    (    !        * .

   

/               "%&'        # 

          

0 1                         &0)**

2 0)*"1 /134&

 *$/        .    2     
   5"&6" 789:;+2<:88=   

0     .   5         0)*"1/134>

"1 >0)**" 2

Teldat Connect-FW 15
4 Compliance Teldat S.A.

*$/+%'   >        '   >+2+ 

?    5"&6" 789:;+2<:88=  

1  #              #  /  0)*"1 &0)*"

2

0 # *$/       .   @        
&0)*" 2       5"&6" 789:;+2<:88=

         AB                

 *              

  * -   -  C  .   '  -   @+
   )  C       *   .        
 '   1  !   

0             A B    
D     0                 
                

5      '      A9 E ;627 B   
 5        '           
 F .          

C *    *   .     '   * 

 - A9 E ;627 GB'    * !    C   * 
    .  ' . G    ,.    1-.   1 
    C   H

*          '        A9 + ;627 +
B   @    *      I    '    #   
            J          

%.                     

' '                 &  +
                        
   

,  *      K '      K  .      
   5 *  .L  +' *  +' C+   )    
*   C *   5     '  L   
    .     )   L 

)   ' D             1   J

 ' '     M  '  -      N  +
       " @        #      I 
  M       ( # 

16 Teldat Connect-FW
Teldat S.A. 4 Compliance

4.4 WEEE information

The crossed-out wheelie bin symbol indicates that the device must be disposed of
separately from normal domestic waste at the end of its useful service life. Please
use an appropriate waste disposal facility.

Das auf dem Gerät befindliche Symbol mit dem durchgekreuzten Müllcontainer
bedeutet, dass das Gerät am Ende der Nutzungsdauer bei den hierfür vorgese-
henen Entsorgungsstellen getrennt vom normalen Hausmüll zu entsorgen ist.

El símbolo del contenedor con la cruz, que se encuentra en el aparato, significa

que cuando el equipo haya llegado al final de su vida útil, deberá ser llevado a los
centros de recogida previstos, y que su tratamiento debe estar separado del de
los residuos urbanos.

4.5 REACH
In compliance with the REACH Candidate List, the delivered product and product packaging do not contain chemical
substances above a concentration limit of 0.1% weight by weight (w/w). This declaration will be updated whenever
any changes occur or other chemical substances are added to the REACH Candidate List. Information is currently
provided to consumers upon request.

4.6 Power usage and energy efficiency

This device is an Energy Related Product (ErP) with High Network Availability (HiNA) and automatically switches to a
power-saving Network Standby mode when no packets have been transmitted for 10 minutes (set by default).

When the Teldat Connect-FW is not needed, it can also be turned off disconnecting the power supply to save en-
ergy.

Network Standby: 6W

All Teldat Connect-FW interfaces can be shut down individually. Check the configuration manuals to learn how to
disableeach interface. For further information, please see manual: “Teldat Dm772-I Configuration Interfaces”.

4.7 PSU energy efficiency

According to Commission Regulation (EU) 2019/1782 laying down ecodesign requirements for external power sup-
plies pursuant to Directive 2009/125/EC of the European Parliament and of the Council and repealing Commission
Regulation (EC) No 278/2009, the instruction manuals for end-users shall include the following information:

Model WA-30P12R

Manufacturer Name ASIAN POWER DEVICES INC. (APD)

Manufacturer Address NO.5 LANE 83. LUNG-SOU ST, TAO-YUAN CITY, TAIWAN R.O.C.

Input Voltage 100-240 Vac

Input AC frequency 50-60 Hz

Output voltage 12.0 V

Output current 2.5 A

Output power 30.0 W

Teldat Connect-FW 17
4 Compliance Teldat S.A.

Average active efficiency 87.7 %

Efficiency at low load (10%) 77.7 %

No-load power consumption Lower than 0.075 W

4.8 EC declaration of conformity

English (EN) Hereby, Teldat S.A. declares that telecommunications equipment Teldat Con-
nect-FW complies with:

Directive 2014/53/EU (RED) or

Directive 2014/30/EU (EMC)

Directive 2014/35/EU (LVD)

Directive 2009/125/EC (ErP)

Directives 2011/65/EU and 2015/863/EU (RoHS)

of the European Parliament and of the Council.

German (DE) Deutsch Hiermit erklärt Teldat S.A. die Übereinstimmung des Geräts Teldat Connect-FW
mit:

Richtlinie 2014/53/EU (RED) oder

Richtlinie 2014/30/EU (EMC)

Richtlinie 2014/35/EU (LVD)

Richtlinie 2009/125/EG (ErP)

Richtlinien 2011/65/EU und 2015/863/EU (RoHS)

des Europäischen Parlaments.

Spanish (ES) Español Por la presente, Teldat S.A. declara que el tipo de equipo de telecomunicaciones
Teldat Connect-FW es conforme con:

Directiva 2014/53/EU (RED) o

Directiva 2014/30/UE (EMC)

Directiva 2014/35/UE (LVD)

Directiva 2009/125/CE (ErP)

Directivas 2011/65/UE y 2015/863/UE (RoHS)

del Parlamento Europeo y del Consejo.

The EC declaration of conformity and additional product documentation can be accessed here:

http://www.teldat.com/conformity

4.9 CE marking
This equipment is in conformity with CE procedures and marking.

18 Teldat Connect-FW
Teldat S.A. 4 Compliance

4.10 National restrictions

In accordance with Article 10 of 2014/53/EU, we inform you that national restrictions and requirements may apply for
authorization purposes. These can change with time. Teldat S.A. recommends that you check with local authorities
for the latest status of national regulations.

This product is supplied with antennas in order to fulfill local regulations.

4.11 Operating frequency

To find out more about operating frequencies and the maximum power transmitted in the frequency bands in which
the radio equipment operates, see appendix WI-FI specifications on page 27.

4.12 Intended use of the equipment

The Teldat Connect-FW can be deployed as a Customer Premises Equipment (CPE) in enterprise branch offices or
in environments managed by the service provider.

This product must only be used indoors.

Teldat Connect-FW 19
Technical Information Teldat S.A.

Appendix A Technical Information

A.1 Troubleshooting
The following table can help you solve problems when installing the device. If you cannot resolve the issue, please
contact your dealer for more information.

Symptom Solution

None of the LEDs light up on Check the power supply to the router (power source, ON/OFF switch, main power
the router. outlet).

You have forgotten the router's Ignore the configuration through the RST button (as explained in the relevant sec-
access password. tion).

The LAN connector LED never Check the Ethernet cable and the connection to the network.
lights up.
For further information, please see manual: “Teldat Dm709-I LAN Interfaces”.

The WAN connector LED never Check the Ethernet cable and the connection to the network.
lights up.
Check the appropriate license is available for use.

For further information, please see manual: “Teldat Dm709-I LAN Interfaces”.

The Wi-Fi LED never lights up in Check the router configuration and that of the remote station(s).
green.
For further information, please see manual: “Teldat Dm771-I WLAN Interfaces”.

A.2 Updating the software

The Teldat Connect-FW router can be updated to new versions. Please contact your dealer for further details on
new releases.

There are several ways to update a Teldat router. For further information, please see manual: “Teldat Dm748-I Soft-
ware Updating”.

The software required to update Teldat routers is supplied in a format known as distribution, which contains all the
files needed to update your device and in-depth information on their content.

The embedded access point (if available) can also be updated to new versions. Please contact your dealer for further
details on new releases for the embedded access point.

A.3 Connecting to the device

A.3.1 Connecting using the local console (AUX connector)

The Teldat Connect-FW router has a RJ45 female connector on the front panel, known as AUX, which provides ac-
cess to the device's local console.

Fig. 19: AUX Connector

20 Teldat Connect-FW
Teldat S.A. Technical Information

To configure this, you must connect the Aux port to an asynchronous terminal (or to a PC with terminal emulation).

Note

The configuration for the terminal must be:

- Speed: 115200 bps.

- Eight data bits.

- One stop bit.

- No parity bit.

- No type of flow control.

Connection to the configuration port can be carried out using the the RJ45 connector cable, supplied with the device,
and an RJ45 female-DB9 female adapter (also provided).

Fig. 20: Connecting for Configuration

For further information, please see manual: “Teldat Dm704-I Configuration and Monitoring”.

A.4 Connectors

A.4.1 LAN connectors

RJ45 LAN RJ45 PIN FE Signals GE Signals

1 BI-DA+ BI-DA+

2 BI-DA- BI-DA-

3 BI-DB+ BI-DB+

4 -- BI-DC+

5 -- BI-DC-

6 BI-DB- BI-DB-

7 -- BI-DD+

8 -- BI-DD-

Teldat Connect-FW 21
Technical Information Teldat S.A.

A.4.2 WAN Base-T connectors

RJ45 WAN RJ45 PIN FE Signals GE Signals

1 BI-DA+ BI-DA+

2 BI-DA- BI-DA-

3 BI-DB+ BI-DB+

4 -- BI-DC+

5 -- BI-DC-

6 BI-DB- BI-DB-

7 -- BI-DD+

8 -- BI-DD-

A.4.3 WAN SFP connector

SFP

Standard SFP connector

A.4.4 Configuration connector

RJ45 CONFIGURATION RJ45 PIN CONF

1 --

2 RxD

3 GND

4 --

5 --

6 GND

7 TxD

8 --

22 Teldat Connect-FW
Teldat S.A. Technical Information

A.4.5 Power supply connector

Jack 5.5/2.5mm PIN

Internal -> POSITIVE

External -> NEGATIVE

A.5 Technical specifications

A.5.1 Hardware architecture

PROCESSORS Freescale LayerScape.

MEMORY 1 GByte (DDR4)

STORAGE UNIT eMMC Memory (4 GBytes).

A.5.2 LAN interface

PROTOCOLS Ethernet (802.3).

PORTS 4-port MDI/MDX auto-detection.

SPEED 10/100/1000 Mbps (Base-T).

CONNECTOR RJ45 female.

A.5.3 WAN Base-T interface

STANDARDS Ethernet (802.3).

SPEED WAN-1: 10/100/1000 Mbps (Base-T).

WAN-2: 10/100/1000/2500 Mbps (Base-T).

CONNECTOR RJ45 female.

Teldat Connect-FW 23
Technical Information Teldat S.A.

A.5.4 WAN SFP interface

STANDARDS 802.1Q (VLAN).

1000-Base-X.

MSA and SFF 8472 compliant.

SPEED 1000 Mbps full duplex.

TYPES LX/LH (single-mode 1310 nm).

SX (multi-mode 850 nm).

ZX (single-mode 1550 nm).

CONNECTOR Standard SFP connector.

24 Teldat Connect-FW
Teldat S.A. Technical Information

A.5.5 Wireless LAN interface

WLAN standards 802.11 a/b/g/n/ac/ax MIMO 2x2 Dual-Band, Dual-Concurrent

Concurrent 2.4 and 5 GHz sup- 5 GHz

ported modes 2.4 GHz

Scn Mode Tech B/W Mode Tech B/W

1 2x2 802.11n 40MHz 2x2 802.11ax 80MHz

2 2x2 802.11n 40MHz 1x1 802.11ax 80MHz

1Rx Zero wait 80MHz

DFS

3 2x2 802.11ax 40MHz 2x2 802.11ac 40MHz

Frequency bands 2.4 GHz in- 2400-2483.5 MHz: max. 100 mW EIRP (20dBm).
door and outdoor (EU)

Frequency bands 2.4 GHz in- 2400-2473 MHz: max. 100 mW EIRP (20dBm).
door and outdoor (USA)

Frequency bands 5 GHz indoor 5170-5330 MHz; max. 200 mW EIRP allowed
(EU), indoor and outdoor (USA)

Frequency bands 5 GHz indoor 5490-5710 MHz; max. 1000 mW EIRP allowed
and outdoor (EU/USA)

Frequency bands 5 GHz indoor 5735-5835 MHz; max. 1000 mW EIRP allowed
and outdoor (USA)

Modulation Techniques DSSS, OFDM, DBPSK, DQPSK, CCK, 16 QAM, 64 QAM.

Automatic Rate Selection (ARS) Available.

Transmission rate Automatic.

Data rates 802.11b: 1, 2, 5.5, 11Mbps.

802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54Mbps

802.11n: up to 150Mbps-single

802.11n: up to 300Mbps-2×2 MIMO

802.11ac: up to 192.6Mbps (20MHz channel)

802.11ac: up to 400Mbps (40MHz channel).

802.11ac: up to 866.7Mbps (80MHz channel)

802.11ax: 2.4GHz up to 458Mbps, 5GHz up to 1.2Gbps.

Output power limitation Adjustable

Output Power @2.4GHz: Max. 16,35 dBm

@5GHz: Max. 18,12 dBm

Teldat Connect-FW 25
Technical Information Teldat S.A.

Bandwidth 802.11n: 20/40 MHz

802.11ac: 20/40/80 MHz

802.11ax: 20/40/80 MHz

Integrated directional dual-band MIMO array
Antenna

A.5.6 Configuration interface

LOCAL TERMINAL RS-232 115200-8-N-1 without flow control.

CONNECTOR RJ45 female on the rear panel.

A.5.7 Power supply

INPUT VOLTAGE +12V DC.

INPUT CURRENT 2.5 A.

CONNECTOR Jack 5.5/2.5 mm.

A.5.8 Dimensions and weight

TYPE Desktop / chassis for a 1 U high Rack mount enclosure.

DIMENSION 283mm x 144mm x 40mm

WEIGHT 0.6 Kg

A.5.9 Environmental specifications

TEMPERATURE OPERATING NORMALLY: 0 ºC to 45 ºC.

STORED: -25 ºC to 70 ºC.

RELATIVE HUMIDITY 10 % to 95 %.

NOISE 38.3 dB SPL (5000 rpm).

26 Teldat Connect-FW
Teldat S.A. CE Radio Information

Appendix B CE Radio Information

This section includes some of the European radio frequencies that comply with CE regulatory requirements. Custom-
ers may obtain additional country-specific bands upon request.

B.1 WI-FI specifications

This product is supplied with internal antennas.

Technology: WLAN 802.11a/b/g/n/ac/ax.

Number of Channels • 2.4GHz.

• EU, 1 ~ 13
• USA: 1 ~ 11
• 5GHz
• EU, USA:
36,40,44,48,52,56,60,64,100,104,108,112,116,120,124,128,132,136,140,149,
153,157,161,165

Tx Power • 2.4GHz.
• 11b (11Mbps): 18 dBm
• 11g (54Mbps): 17 dBm
• 11n (HT20 MCS7): 16 dBm
• 11n (HT40 MCS7): 16 dBm
• 11ax (HE20 MCS11): 14 dBm
• 11ax (HE40 MCS11): 14 dBm
• 5GHz
• 11a (54Mbps): 16 dBm
• 11n (HT20 MCS7): 16 dBm
• 11n (HT40 MCS7): 16 dBm
• 11ac(VHT20 MCS8): 15 dBm
• 11ac(VHT40 MCS9): 15 dBm
• 11ac(VHT80 MCS9): 15 dBm
• 11ax(HE20 MCS11): 12 dBm
• 11ax(HE40 MCS11): 12 dBm
• 11ax(HE80 MCS11): 12 dBm

Receiver Sensitivity • 2.4GHz.

• 11b(11Mbps): -88 dBm
• 11g(54Mbps): -75 dBm
• 11n(HT20 MCS7): -72 dBm
• 11n(HT40 MCS7): -70 dBm
• 11ax(HE20 MCS11): -62 dBm
• 11ax(HE40 MCS11): -59 dBm
• 5GHz
• 11a(54Mbps): -68 dBm
• 11n(HT20 MCS7): -66 dBm
• 11n(HT40 MCS7): -64 dBm
• 11ac(VHT20 MCS8): -61 dBm

Teldat Connect-FW 27
CE Radio Information Teldat S.A.

• 11ac(VHT40 MCS9): -58 dBm

• 11ac(VHT80 MCS9): -55 dBm
• 11ax(HE20 MCS11): -56 dBm
• 11ax(HE40 MCS11): -53 dBm
• 11ax(HE80 MCS11): -51 dBm

28 Teldat Connect-FW