COMPOUND SELECTION

Nitrile (NBR)
Nitrile rubber, which has excellent resistance to petroleum products and fuel, has been the most
widely used elastomer for sealing applications. It is a copolymer of acrylonitrile and butadiene, being
available in various ratios of these two monomers. The formulations with a high ratio of acrylonitrile,
over 50%, have strong resistance to oil and fuel. Those versions with over 78% of butadiene obtain
good resistance to low temperatures, although they have to sacrifice some oil and fuel resistance at
high temperatures.

In comparison to most elastomers, the NBR rubber’s tensile strength, elongation properties, cold
flow, compression set and resistance to oil, petroleum, tear and abrasion perform better than most.
However, inherently special compounding is required increased weather ability and improved
resistance to ozone and sunlight.

Ethylene Propylene (EPDM)

EPDM rubber is popular in the sealing industry due to its excellent resistance to Skydrol and other
phosphate ester type hydraulic fluids. EPDM is often used in hot/cold water applications, steam and
hydraulics systems, however EPDM has poor resistance to most oils, fuels and hydrocarbons.

EPDM rubbers have high tensile strength and elongation, with excellent resistance to oxygen, ozone
and amongst the elastomers has exceptional resistance to weathering. EPDM has good recovery
characteristics, low compression sealing, good heat resistance and good electrical resistance
properties. EPDM service temperature range is approximately -50°C to 125°C.

Fluorocarbon (Viton)
Fluorocarbon rubbers are suitable for a wide range of service temperatures from approximately -20°C
to 200°C. The temperature can be as high as 315°C for short periods and as low as -50°C in some
static applications. Fluorocarbon rubber is growing in popularity as the market starts to acknowledge
its potential uses with a wide spectrum of chemical compatibility and excellent resistance to oils,
solvents, flames and heat. The petroleum, chemical and aviation industries have found them beneficial
due to their resistance to hot engine lubricants. As time has progressed, newer formulations have
tremendously improved the compression set characteristics and lower elongation properties. Due to
their increased popularity more ranges of fluorocarbon O-Rings have been made more commercially
available. Viton is a tradename of DuPont.

Neoprene (CR)
Neoprene rubbers are manufactured by polymerising chlorine and butadiene. They resist heat,
Klinger Acorn

oil, chemicals, ozone, weathering, flexing and compression set. Most elastomers are resistant to
deterioration from exposure to petroleum lubricants and oxygen. Neoprene service temperature
ranges from approximately -30°C to 110°C. Neoprene is a tradename of DuPont.

Polyurethane (PU)
Polyurethane is any polymer consisting of a chain of organic units joined together by urethane
links. In the sealing industry polyurethane offers excellent abrasive resistance compared to rubber
products, good load bearing capabilities, excellent dimensional stability under high pressures and
is chemically resistant to solvents, oils, fuels, dilute acids and alkalis. Polyurethane is offered for
heavy duty applications for pressures up to approximately 350bar. Polyurethane has reasonable low
temperature resistance compared to elastomers with a service temperature approximately between
-40°C to 90°C. Over 50°C in water submersion polyurethane is subjected to hydrolysis, causing the
polymer to degrade.

242
Telephone : 01274 - 688222
 Fax
E-mail
: 01274 - 688549
: [email protected]
 COMPOUND SELECTION
Silicone (VMQ)
Silicone has an unusual molecular structure. This polymer consists of long chains of alternating silicone
and oxygen, encased by organic groups. As a group, the silicones have poor tensile strength, tear
and abrasion resistance. However, they have a broad service temperature range that far exceeds that
of any other commercially available rubber. Silicones can be compounded to perform for extended
periods at approximately -100°C to 315°C under static conditions, and at approximately -73°C to
315°C under dynamic conditions. Their retention of properties at these high temperatures is superior
to other elastomers.

The compression set of silicone rubbers, as a measure of their perfect elasticity at any temperature, is
equal or superior to that of any generally available elastomer. Silicone rubbers are odourless, tasteless
and non-toxic. Due to their exceptional mechanical and electrical performance under extreme
temperature conditions, silicone rubbers are widely used in hundreds of commercial and military
applications. In many cases it is the inertness, non-toxicity, ease of processing and their resistance to
heat, high aniline point oils, ozone and weathering that are also of critical importance. Silicone rubbers
are not normally recommended for dynamic sealing due to the relatively low abrasion resistance.

Fluorosilicone (FVMQ)
Fluorosilicone is serviceable over a wide temperature range from approximately -60°C to 180°C. It
has a relatively low tensile strength and elongation, but these properties are retained under a broad
range of aging conditions. It combines the outstanding high and low temperature properties of
silicone rubber with excellent swelling resistance to many commonly used fuels, oils and solvents.
These rubbers also have low compression set, good electrical properties and excellent resistance to
ozone and weathering. Fluorosilicone elastomers are not recommended for the use with ketones and
phosphates esters.

Temperature Range
This chart is for reference Celsius (˚C)
only. In an actual service
-50 0 50 100 150 200
environment some specific
compounds may not reach -30˚C 110˚C
Nitrile
the maximum/minimum -22˚F 230˚F
temperatures as indicated in
this chart, however higher/ -30˚C 110˚C
Neoprene
-22˚F 230˚F
lower temperatures may
be attained if exposure is -50˚C 125˚C
Ethylene Propylene

Klinger Acorn
for short periods of time or -58˚F 257˚F
intermittent use.
-20˚C 200˚C
Fluorocarbon
-4˚F 392˚F

-60˚C 250˚C
Silicone
-76˚F 482˚F

-60˚C 180˚C
Fluorosilicone
-76˚F 356˚F

-40˚C 90˚C
Polyurethane
-40˚F 194˚F

-58 32 122 212 302 392

Fahrenheit (˚F)

243
Telephone : 01274 - 688222
 Fax
E- mail
: 01274 - 688549
: [email protected]
 O-RINGS

Introduction
O-Rings are used as sealing elements or as energising wipers
and hydraulic seals, so they cover an extensive number of
applications. The simplistic design, ease of manufacture and
compact design make O-Rings useful in nearly every field
of industry. We offer a wide choice of elastomer materials
in both standard and custom O-Rings for both static and
dynamic applications.
Typical Reciprocating Seal Arrangement
Piston Gland

Break Corners
Rod Gland 5° Approx. 0.005" Rad.
(TYP)
1/2E
16—"

R 32—"
32—" Gland
F L
Depth

B-1 Piston Groove Dia

B Rod O.D 32—"
(B-1 Min = A Max - 2L Max)

C Piston O.D D Rod Bore Dia G F Groove

Depth (Ref.)
A Cylinder Bore Diameter A-1 Rod Gland Groove I.D
( A-1 Min = B Max + 2L Max)

G, Groove Width
L, Groove Depth Squeeze
W, E, ± 0.005”
R,
O-Ring Radial Axial Diametrical No One Two Eccentricity
Groove
Cross Clearance Back- Back- Back- (Max)
Radial Axial Radius
section Inches % Inches % (Max) Up Up Up
Rings Ring Rings

0.07 0.049-0.055 0.045-0.050 0.012-0.014 18-19 0.017-0.028 25.5-38.5 0.004 0.095 0.140 0.207 0.005-0.015 0.002

0.103 0.080-0.086 0.072-0.080 0.014-0.026 13.5-25 0.020-0.034 20-32 0.005 0.142 0.173 0.240 0.005-0.015 0.002

0.139 0.122-0.118 0.100-0.110 0.017-0.031 12.5-29 0.025-0.043 18.5-30 0.006 0.189 0.210 0.277 0.010-0.025 0.003

0.210 0.176-0.184 0.165-0.175 0.021-0.039 10-18 0.030-0.050 14.5-23 0.006 0.283 0.313 0.413 0.020-0.035 0.004
Klinger Acorn

0.275 0.225-0.235 0.220-.0230 0.034-0.056 12.5-20 0.039-0.061 14.5-21.5 0.007 0.377 0.410 0.540 0.020-0.035 0.005

All dimensions in Inches

PRESSURE PRESSURE PRESSURE

I.D.

G G G
W
No Back-Up Ring One Back-Up Ring Two Back-Up Rings

244
Telephone : 01274 - 688222
 Fax
E-mail
: 01274 - 688549
: [email protected]
 O-RINGS

Typical Static Seal Arrangement

Female Gland

Male Gland
Break Corners
5°
Approx. 0.005" Rad.
(TYP)

1/2E
0.5
0.5 16—"

R 63—"
63—" Gland
F L
Depth

B-1 Piston Groove Dia 32—"

B Tube O.D
(B-1 Min = A Max - 2L Max)
G F Groove
C Piston/Cylinder O.D D Throat Dia
Depth (Ref.)

A Cylinder Bore Diameter A-1 Groove Dia

( A-1 Min = B Max + 2L Max)

Squeeze E, G, Groove Width ± 0.005”

W, O-Ring L,
Diametrical R, Groove Eccentricity
Cross Groove No Back- One Back- Two Back-
Inches % Clearance Radius (Max)
section Depth Up Rings Up Ring Up Rings
(Max)

0.07 0.055-0.057 0.010-0.018 15-25 0.004 0.095 0.140 0.207 0.005-0.015 0.002

0.103 0.087-0.090 0.010-0.019 10-18 0.005 0.142 0.173 0.240 0.005-0.015 0.002

0.139 0.119-0.123 0.012-0.24 9-17 0.006 0.189 0.210 0.277 0.010-0.025 0.003

0.210 0.183-0.188 0.017-0.032 8.5-15 0.006 0.283 0.313 0.413 0.020-0.035 0.004

0.275 0.234-0.240 0.029-0.047 10.5-17 0.007 0.377 0.410 0.540 0.020-0.035 0.005

Klinger Acorn
All Dimensions in Inches

245
Telephone : 01274 - 688222
 Fax
E- mail
: 01274 - 688549
: [email protected]
 O-RING REFERENCE GUIDE
Nominal Size (inches) Standard O-Ring Size (Inches) Metric O-Ring Size (mm)
O-Ring
Reference Inches Actual Per AS 568A Actual Per AS 568A
number
ID OD W ID +/- W +/- ID +/- W +/-
BS-001 1/32 3/32 1/32 0.029 0.004 0.040 0.003 0.74 0.10 1.02 0.08
BS-002 3/64 9/64 3/64 0.042 0.004 0.050 0.003 1.07 0.10 1.27 0.08
BS-003 1/16 3/16 1/16 0.056 0.004 0.060 0.003 1.42 0.10 1.52 0.08
BS-004 5/64 13/64 1/16 0.070 0.005 0.070 0.003 1.78 0.13 1.78 0.08
BS-005 3/32 7/32 1/16 0.101 0.005 0.070 0.003 2.57 0.13 1.78 0.08
BS-006 1/8 1/4 1/16 0.114 0.005 0.070 0.003 2.90 0.13 1.78 0.08
BS-007 5/32 9/32 1/16 0.145 0.005 0.070 0.003 3.68 0.13 1.78 0.08
BS-008 3/16 5/16 1/16 0.176 0.005 0.070 0.003 4.47 0.13 1.78 0.08
BS-009 7/32 11/32 1/16 0.208 0.005 0.070 0.003 5.28 0.13 1.78 0.08
BS-010 1/4 3/8 1/16 0.239 0.005 0.070 0.003 6.07 0.13 1.78 0.08
BS-011 5/16 7/16 1/16 0.301 0.005 0.070 0.003 7.65 0.13 1.78 0.08
BS-012 3/8 1/2 1/16 0.364 0.005 0.070 0.003 9.25 0.13 1.78 0.08
BS-013 7/16 9/16 1/16 0.426 0.005 0.070 0.003 10.82 0.13 1.78 0.08
BS-014 1/2 5/8 1/16 0.489 0.005 0.070 0.003 12.42 0.13 1.78 0.08
BS-015 9/16 11/16 1/16 0.551 0.007 0.070 0.003 14.00 0.18 1.78 0.08
BS-016 5/8 3/4 1/16 0.614 0.009 0.070 0.003 15.60 0.23 1.78 0.08
BS-017 11/16 13/16 1/16 0.676 0.009 0.070 0.003 17.17 0.23 1.78 0.08
BS-018 3/4 7/8 1/16 0.739 0.009 0.070 0.003 18.77 0.23 1.78 0.08
BS-019 13/16 15/16 1/16 0.801 0.009 0.070 0.003 20.35 0.23 1.78 0.08
BS-020 7/8 1 1/16 0.864 0.009 0.070 0.003 21.95 0.23 1.78 0.08
BS-021 15/16 1 1/16 1/16 0.926 0.009 0.070 0.003 23.52 0.23 1.78 0.08
BS-022 1 1 1/8 1/16 0.989 0.010 0.070 0.003 25.12 0.25 1.78 0.08
BS-023 1 1/16 1 3/16 1/16 1.051 0.010 0.070 0.003 26.70 0.25 1.78 0.08
BS-024 1 1/8 1 1/4 1/16 1.114 0.010 0.070 0.003 28.30 0.25 1.78 0.08
BS-025 1 3/16 1 5/16 1/16 1.176 0.011 0.070 0.003 29.87 0.28 1.78 0.08
BS-026 1 1/4 1 3/8 1/16 1.239 0.011 0.070 0.003 31.47 0.28 1.78 0.08
BS-027 1 5/16 1 7/16 1/16 1.301 0.011 0.070 0.003 33.05 0.28 1.78 0.08
BS-028 1 3/8 1 1/2 1/16 1.364 0.013 0.070 0.003 34.65 0.33 1.78 0.08
BS-029 1 1/2 1 5/8 1/16 1.489 0.013 0.070 0.003 37.82 0.33 1.78 0.08
BS-030 1 5/8 1 3/4 1/16 1.614 0.013 0.070 0.003 41.00 0.33 1.78 0.08
BS-031 1 3/4 1 7/8 1/16 1.739 0.015 0.070 0.003 44.17 0.38 1.78 0.08
BS-032 1 7/8 2 1/16 1.864 0.015 0.070 0.003 47.35 0.38 1.78 0.08
Klinger Acorn

BS-033 2 2 1/8 1/16 1.989 0.018 0.070 0.003 50.52 0.46 1.78 0.08
BS-034 2 1/8 2 1/4 1/16 2.114 0.018 0.070 0.003 53.70 0.46 1.78 0.08
BS-035 2 1/4 2 3/8 1/16 2.239 0.018 0.070 0.003 56.87 0.46 1.78 0.08
BS-036 2 3/8 2 1/2 1/16 2.364 0.018 0.070 0.003 60.05 0.46 1.78 0.08
BS-037 2 1/2 2 5/8 1/16 2.489 0.018 0.070 0.003 63.22 0.46 1.78 0.08
BS-038 2 5/8 2 3/4 1/16 2.614 0.020 0.070 0.003 66.40 0.51 1.78 0.08
BS-039 2 3/4 2 7/8 1/16 2.739 0.020 0.070 0.003 69.57 0.51 1.78 0.08
BS-040 2 7/8 3 1/16 2.864 0.020 0.070 0.003 72.75 0.61 1.78 0.08
BS-041 3 3 1/8 1/16 2.989 0.024 0.070 0.003 75.92 0.51 1.78 0.08
BS-042 3 1/4 3 3/8 1/16 3.239 0.024 0.070 0.003 82.27 0.61 1.78 0.08
BS-043 3 1/2 3 5/8 1/16 3.489 0.024 0.070 0.003 88.62 0.61 1.78 0.08
BS-044 3 3/4 3 7/8 1/16 3.739 0.027 0.070 0.003 94.97 0.69 1.78 0.08
BS-045 4 4 1/8 1/16 3.989 0.027 0.070 0.003 101.32 0.69 1.78 0.08
BS-046 4 1/4 4 3/8 1/16 4.239 0.030 0.070 0.003 107.67 0.76 1.78 0.08

246
Telephone : 01274 - 688222
 Fax
E-mail
: 01274 - 688549
: [email protected]
 O-RING REFERENCE GUIDE
Nominal Size (inches) Standard O-Ring Size (Inches) Metric O-Ring Size (mm)
O-Ring
Reference Inches Actual Per AS 568A Actual Per AS 568A
number
ID OD W ID +/- W +/- ID +/- W +/-
BS-047 4 1/2 4 5/8 1/16 4.489 0.030 0.070 0.003 114.02 0.76 1.78 0.08
BS-048 4 3/4 4 7/8 1/16 4.739 0.030 0.070 0.003 120.37 0.76 1.78 0.08
BS-049 5 5 1/8 1/16 4.989 0.037 0.070 0.003 126.72 0.94 1.78 0.08
BS-050 5 1/4 5 3/8 1/16 5.239 0.037 0.070 0.003 133.07 0.94 1.78 0.08
BS-102 1/16 1/4 3/32 0.049 0.005 0.103 0.003 1.24 0.13 2.62 0.08
BS-103 3/32 9/32 3/32 0.081 0.005 0.103 0.003 2.06 0.13 2.62 0.08
BS-104 1/8 5/16 3/32 0.112 0.005 0.103 0.003 2.84 0.13 2.62 0.08
BS-105 5/32 11/32 3/32 0.143 0.005 0.103 0.003 3.63 0.13 2.62 0.08
BS-106 3/16 3/8 3/32 0.174 0.005 0.103 0.003 4.42 0.13 2.62 0.08
BS-107 7/32 13/32 3/32 0.206 0.005 0.103 0.003 5.23 0.13 2.62 0.08
BS-108 1/4 7/16 3/32 0.237 0.005 0.103 0.003 6.02 0.13 2.62 0.08
BS-109 5/16 1/2 3/32 0.299 0.005 0.103 0.003 7.59 0.13 2.62 0.08
BS-110 3/8 9/16 3/32 0.362 0.005 0.103 0.003 9.19 0.13 2.62 0.08
BS-111 7/16 5/8 3/32 0.424 0.005 0.103 0.003 10.77 0.13 2.62 0.08
BS-112 1/2 11/16 3/32 0.487 0.005 0.103 0.003 12.37 0.13 2.62 0.08
BS-113 9/16 3/4 3/32 0.549 0.007 0.103 0.003 13.94 0.18 2.62 0.08
BS-114 5/8 13/16 3/32 0.612 0.009 0.103 0.003 15.54 0.23 2.62 0.08
BS-115 11/16 7/8 3/32 0.674 0.009 0.103 0.003 17.12 0.23 2.62 0.08
BS-116 3/4 15/16 3/32 0.737 0.009 0.103 0.003 18.72 0.23 2.62 0.08
BS-117 13/16 1 3/32 0.799 0.010 0.103 0.003 20.30 0.25 2.62 0.08
BS-118 7/8 1 1/6 3/32 0.862 0.010 0.103 0.003 21.89 0.25 2.62 0.08
BS-119 15/16 1 1/8 3/32 0.924 0.010 0.103 0.003 23.47 0.25 2.62 0.08
BS-120 1 1 3/16 3/32 0.987 0.010 0.103 0.003 25.07 0.25 2.62 0.08
BS-121 1 1/16 1 1/4 3/32 1.049 0.010 0.103 0.003 26.64 0.25 2.62 0.08
BS-122 1 1/8 1 5/16 3/32 1.112 0.010 0.103 0.003 28.24 0.25 2.62 0.08
BS-123 1 3/16 1 3/8 3/32 1.174 0.012 0.103 0.003 29.82 0.30 2.62 0.08
BS-124 1 1/4 1 7/16 3/32 1.237 0.012 0.103 0.003 31.42 0.30 2.62 0.08
BS-125 1 5/16 1 1/2 3/32 1.299 0.012 0.103 0.003 32.99 0.30 2.62 0.08
BS-126 1 3/8 1 9/16 3/32 1.362 0.012 0.103 0.003 34.59 0.30 2.62 0.08
BS-127 1 7/16 1 5/8 3/32 1.424 0.012 0.103 0.003 36.17 0.30 2.62 0.08
BS-128 1 1/2 1 11/16 3/32 1.487 0.012 0.103 0.003 37.77 0.30 2.62 0.08
BS-129 1 9/16 1 3/4 3/32 1.549 0.015 0.103 0.003 39.34 0.38 2.62 0.08
BS-130 1 5/8 1 13/16 3/32 1.612 0.015 0.103 0.003 40.94 0.38 2.62 0.08

Klinger Acorn
BS-131 1 11/16 1 7/8 3/32 1.674 0.015 0.103 0.003 42.52 0.38 2.62 0.08
BS-132 1 3/4 1 15/16 3/32 1.737 0.015 0.103 0.003 44.12 0.38 2.62 0.08
BS-133 1 13/16 2 3/32 1.799 0.015 0.103 0.003 45.69 0.38 2.62 0.08
BS-134 1 7/8 2 1/16 3/32 1.862 0.015 0.103 0.003 47.29 0.38 2.62 0.08
BS-135 1 15/16 2 1/8 3/32 1.925 0.017 0.103 0.003 48.90 0.43 2.62 0.08
BS-136 2 2 3/16 3/32 1.987 0.017 0.103 0.003 50.47 0.43 2.62 0.08
BS-137 2 1/16 2 1/4 3/32 2.050 0.017 0.103 0.003 52.07 0.43 2.62 0.08
BS-138 2 1/8 2 5/16 3/32 2.112 0.017 0.103 0.003 53.64 0.43 2.62 0.08
BS-139 2 3/16 2 3/8 3/32 2.175 0.017 0.103 0.003 55.25 0.43 2.62 0.08
BS-140 2 1/4 2 7/16 3/32 2.237 0.017 0.103 0.003 56.82 0.43 2.62 0.08
BS-141 2 5/16 2 1/2 3/32 2.300 0.020 0.103 0.003 58.42 0.51 2.62 0.08
BS-142 2 3/8 2 9/16 3/32 2.362 0.020 0.103 0.003 59.99 0.51 2.62 0.08
BS-143 2 7/16 2 5/8 3/32 2.425 0.020 0.103 0.003 61.60 0.51 2.62 0.08

247
Telephone : 01274 - 688222
 Fax
E- mail
: 01274 - 688549
: [email protected]
 O-RING REFERENCE GUIDE
Nominal Size (inches) Standard O-Ring Size (Inches) Metric O-Ring Size (mm)
O-Ring
Reference Inches Actual Per AS 568A Actual Per AS 568A
number
ID OD W ID +/- W +/- ID +/- W +/-
BS-144 2 1/2 2 11/16 3/32 2.487 0.020 0.103 0.003 63.17 0.51 2.62 0.08
BS-145 2 9/16 2 3/4 3/32 2.550 0.020 0.103 0.003 64.77 0.51 2.62 0.08
BS-146 2 5/8 2 13/16 3/32 2.612 0.020 0.103 0.003 66.34 0.51 2.62 0.08
BS-147 2 11/16 2 7/8 3/32 2.675 0.022 0.103 0.003 67.95 0.56 2.62 0.08
BS-148 2 3/4 2 15/16 3/32 2.737 0.022 0.103 0.003 69.52 0.56 2.62 0.08
BS-149 2 13/16 3 3/32 2.800 0.022 0.103 0.003 71.12 0.56 2.62 0.08
BS-150 2 7/8 3 1/16 3/32 2.862 0.022 0.103 0.003 72.69 0.56 2.62 0.08
BS-151 3 3 3/16 3/32 2.987 0.024 0.103 0.003 75.87 0.61 2.62 0.08
BS-152 3 1/4 3 7/16 3/32 3.237 0.024 0.103 0.003 82.22 0.61 2.62 0.08
BS-153 3 1/2 3 11/16 3/32 3.487 0.024 0.103 0.003 88.57 0.61 2.62 0.08
BS-154 3 3/4 3 15/16 3/32 3.737 0.028 0.103 0.003 94.92 0.71 2.62 0.08
BS-155 4 4 3/16 3/32 3.987 0.028 0.103 0.003 101.27 0.71 2.62 0.08
BS-156 4 1/4 4 7/16 3/32 4.237 0.030 0.103 0.003 107.62 0.76 2.62 0.08
BS-157 4 1/2 4 11/16 3/32 4.487 0.030 0.103 0.003 113.97 0.76 2.62 0.08
BS-158 4 3/4 4 15/16 3/32 4.737 0.030 0.103 0.003 120.32 0.76 2.62 0.08
BS-159 5 5 3/16 3/32 4.987 0.035 0.103 0.003 126.67 0.89 2.62 0.08
BS-160 5 1/4 5 7/16 3/32 5.237 0.035 0.103 0.003 133.02 0.89 2.62 0.08
BS-161 5 1/2 5 11/16 3/32 5.487 0.035 0.103 0.003 139.37 0.89 2.62 0.08
BS-162 5 3/4 5 15/16 3/32 5.737 0.035 0.103 0.003 145.72 0.89 2.62 0.08
BS-163 6 6 3/16 3/32 5.987 0.035 0.103 0.003 152.07 0.89 2.62 0.08
BS-164 6 1/4 6 7/16 3/32 6.237 0.040 0.103 0.003 158.42 1.02 2.62 0.08
BS-165 6 1/2 6 11/16 3/32 6.487 0.040 0.103 0.003 164.77 1.02 2.62 0.08
BS-166 6 3/4 6 15/16 3/32 6.737 0.040 0.103 0.003 171.12 1.02 2.62 0.08
BS-167 7 7 3/16 3/32 6.987 0.040 0.103 0.003 177.47 1.02 2.62 0.08
BS-168 7 1/4 7 7/16 3/32 7.237 0.045 0.103 0.003 183.82 1.14 2.62 0.08
BS-169 7 1/2 7 11/16 3/32 7.487 0.045 0.103 0.003 190.17 1.14 2.62 0.08
BS-170 7 3/4 7 15/16 3/32 7.737 0.045 0.103 0.003 196.52 1.14 2.62 0.08
BS-171 8 8 3/16 3/32 7.987 0.045 0.103 0.003 202.87 1.14 2.62 0.08
BS-172 8 1/4 8 7/16 3/32 8.237 0.050 0.103 0.003 209.22 1.27 2.62 0.08
BS-173 8 1/2 8 11/16 3/32 8.487 0.050 0.103 0.003 215.57 1.27 2.62 0.08
BS-174 8 3/4 8 15/16 3/32 8.737 0.050 0.103 0.003 221.92 1.27 2.62 0.08
BS-175 9 9 3/16 3/32 8.987 0.050 0.103 0.003 228.27 1.27 2.62 0.08
Klinger Acorn

BS-176 9 1/4 9 7/16 3/32 9.237 0.055 0.103 0.003 234.62 1.40 2.62 0.08
BS-177 9 1/2 9 11/16 3/32 9.487 0.055 0.103 0.003 240.97 1.40 2.62 0.08
BS-178 9 3/4 9 15/16 3/32 9.737 0.055 0.103 0.003 247.32 1.40 2.62 0.08
BS-201 3/16 7/16 1/8 0.171 0.005 0.139 0.004 4.34 0.13 3.53 0.10
BS-202 1/4 1/2 1/8 0.234 0.005 0.139 0.004 5.94 0.13 3.53 0.10
BS-203 5/16 9/16 1/8 0.296 0.005 0.139 0.004 7.52 0.13 3.53 0.10
BS-204 3/8 5/8 1/8 0.359 0.005 0.139 0.004 9.12 0.13 3.53 0.10
BS-205 7/16 11/16 1/8 0.421 0.005 0.139 0.004 10.69 0.13 3.53 0.10
BS-206 1/2 3/4 1/8 0.484 0.005 0.139 0.004 12.29 0.13 3.53 0.10
BS-207 9/16 13/16 1/8 0.546 0.007 0.139 0.004 13.87 0.18 3.53 0.10
BS-208 5/8 7/8 1/8 0.609 0.009 0.139 0.004 15.47 0.23 3.53 0.10
BS-209 11/16 15/16 1/8 0.671 0.010 0.139 0.004 17.04 0.23 3.53 0.10
BS-210 3/4 1 1/8 0.734 0.010 0.139 0.004 18.64 0.25 3.53 0.10
BS-211 13/16 1 1/16 1/8 0.796 0.010 0.139 0.004 20.22 0.25 3.53 0.10

248
Telephone : 01274 - 688222
 Fax
E-mail
: 01274 - 688549
: [email protected]
 O-RING REFERENCE GUIDE
Nominal Size (inches) Standard O-Ring Size (Inches) Metric O-Ring Size (mm)
O-Ring
Reference Inches Actual Per AS 568A Actual Per AS 568A
number
ID OD W ID +/- W +/- ID +/- W +/-
BS-212 7/8 1 1/8 1/8 0.859 0.010 0.139 0.004 21.82 0.25 3.53 0.10
BS-213 15/16 1 3/16 1/8 0.921 0.010 0.139 0.004 23.39 0.25 3.53 0.10
BS-214 1 1 1/4 1/8 0.984 0.010 0.139 0.004 24.99 0.25 3.53 0.10
BS-215 1 1/16 1 5/16 1/8 1.046 0.010 0.139 0.004 26.57 0.25 3.53 0.10
BS-216 1 1/8 1 3/8 1/8 1.109 0.012 0.139 0.004 28.17 0.30 3.53 0.10
BS-217 1 3/16 1 7/16 1/8 1.171 0.012 0.139 0.004 29.74 0.30 3.53 0.10
BS-218 1 1/4 1 1/2 1/8 1.234 0.012 0.139 0.004 31.34 0.30 3.53 0.10
BS-219 1 5/16 1 9/16 1/8 1.296 0.012 0.139 0.004 32.92 0.30 3.53 0.10
BS-220 1 3/8 1 5/8 1/8 1.359 0.012 0.139 0.004 34.52 0.30 3.53 0.10
BS-221 1 7/16 1 11/16 1/8 1.421 0.012 0.139 0.004 36.09 0.30 3.53 0.10
BS-222 1 1/2 1 3/4 1/8 1.484 0.015 0.139 0.004 37.69 0.38 3.53 0.10
BS-223 1 5/8 1 7/8 1/8 1.609 0.015 0.139 0.004 40.87 0.38 3.53 0.10
BS-224 1 3/4 2 1/8 1.734 0.015 0.139 0.004 44.04 0.38 3.53 0.10
BS-225 1 7/8 2 1/8 1/8 1.859 0.018 0.139 0.004 47.22 0.46 3.53 0.10
BS-226 2 2 1/4 1/8 1.984 0.018 0.139 0.004 50.39 0.46 3.53 0.10
BS-227 2 1/8 2 3/8 1/8 2.109 0.018 0.139 0.004 53.57 0.46 3.53 0.10
BS-228 2 1/4 2 1/2 1/8 2.234 0.020 0.139 0.004 56.74 0.51 3.53 0.10
BS-229 2 3/8 2 5/8 1/8 2.359 0.020 0.139 0.004 59.92 0.51 3.53 0.10
BS-230 2 1/2 2 3/4 1/8 2.484 0.020 0.139 0.004 63.09 0.51 3.53 0.10
BS-231 2 5/8 2 7/8 1/8 2.609 0.020 0.139 0.004 66.27 0.51 3.53 0.10
BS-232 2 3/4 3 1/8 2.734 0.024 0.139 0.004 69.44 0.61 3.53 0.10
BS-233 2 7/8 3 1/8 1/8 2.859 0.024 0.139 0.004 72.62 0.61 3.53 0.10
BS-234 3 3 1/4 1/8 2.984 0.024 0.139 0.004 75.79 0.61 3.53 0.10
BS-235 3 1/8 3 3/8 1/8 3.109 0.024 0.139 0.004 78.97 0.61 3.53 0.10
BS-236 3 1/4 3 1/2 1/8 3.234 0.024 0.139 0.004 82.14 0.61 3.53 0.10
BS-237 3 3/8 3 5/8 1/8 3.359 0.024 0.139 0.004 85.32 0.61 3.53 0.10
BS-238 3 1/2 3 3/4 1/8 3.484 0.024 0.139 0.004 88.49 0.61 3.53 0.10
BS-239 3 5/8 3 7/8 1/8 3.609 0.028 0.139 0.004 91.67 0.71 3.53 0.10
BS-240 3 3/4 4 1/8 3.734 0.028 0.139 0.004 94.84 0.71 3.53 0.10
BS-241 3 7/8 4 1/8 1/8 3.859 0.028 0.139 0.004 98.02 0.71 3.53 0.10
BS-242 4 4 1/4 1/8 3.984 0.028 0.139 0.004 101.19 0.71 3.53 0.10
BS-243 4 1/8 4 3/8 1/8 4.109 0.028 0.139 0.004 104.37 0.71 3.53 0.10
BS-244 4 1/4 4 1/2 1/8 4.234 0.030 0.139 0.004 107.54 0.76 3.53 0.10

Klinger Acorn
BS-245 4 3/8 4 5/8 1/8 4.359 0.030 0.139 0.004 110.72 0.76 3.53 0.10
BS-246 4 1/2 4 3/4 1/8 4.484 0.030 0.139 0.004 113.89 0.76 3.53 0.10
BS-247 4 5/8 4 7/8 1/8 4.609 0.030 0.139 0.004 117.07 0.76 3.53 0.10
BS-248 4 3/4 5 1/8 4.734 0.030 0.139 0.004 120.24 0.76 3.53 0.10
BS-249 4 7/8 5 1/8 1/8 4.859 0.035 0.139 0.004 123.42 0.89 3.53 0.10
BS-250 5 5 1/4 1/8 4.984 0.035 0.139 0.004 126.59 0.89 3.53 0.10
BS-251 5 1/8 5 3/8 1/8 5.109 0.035 0.139 0.004 129.77 0.89 3.53 0.10
BS-252 5 1/4 5 1/2 1/8 5.234 0.035 0.139 0.004 132.94 0.89 3.53 0.10
BS-253 5 3/8 5 5/8 1/8 5.359 0.035 0.139 0.004 136.12 0.89 3.53 0.10
BS-254 5 1/2 5 3/4 1/8 5.484 0.035 0.139 0.004 139.29 0.89 3.53 0.10
BS-255 5 5/8 5 7/8 1/8 5.609 0.035 0.139 0.004 142.47 0.89 3.53 0.10
BS-256 5 3/4 6 1/8 5.734 0.035 0.139 0.004 145.64 0.89 3.53 0.10
BS-257 5 7/8 6 1/8 1/8 5.859 0.035 0.139 0.004 148.82 0.89 3.53 0.10

249
Telephone : 01274 - 688222
 Fax
E- mail
: 01274 - 688549
: [email protected]
 O-RING REFERENCE GUIDE
Nominal Size (inches) Standard O-Ring Size (Inches) Metric O-Ring Size (mm)
O-Ring
Reference Inches Actual Per AS 568A Actual Per AS 568A
number
ID OD W ID +/- W +/- ID +/- W +/-
BS-258 6 6 1/4 1/8 5.984 0.035 0.139 0.004 151.99 0.89 3.53 0.10
BS-259 6 1/4 6 1/2 1/8 6.234 0.040 0.139 0.004 158.34 1.02 3.53 0.10
BS-260 6 1/2 6 3/4 1/8 6.484 0.040 0.139 0.004 164.69 1.02 3.53 0.10
BS-261 6 3/4 7 1/8 6.734 0.040 0.139 0.004 171.04 1.02 3.53 0.10
BS-262 7 7 1/4 1/8 6.984 0.040 0.139 0.004 177.39 1.02 3.53 0.10
BS-263 7 1/4 7 1/2 1/8 7.234 0.045 0.139 0.004 183.74 1.14 3.53 0.10
BS-264 7 1/2 7 3/4 1/8 7.484 0.045 0.139 0.004 190.09 1.14 3.53 0.10
BS-265 7 3/4 8 1/8 7.734 0.045 0.139 0.004 196.44 1.14 3.53 0.10
BS-266 8 8 1/4 1/8 7.984 0.045 0.139 0.004 202.79 1.14 3.53 0.10
BS-267 8 1/4 8 1/2 1/8 8.234 0.050 0.139 0.004 209.14 1.27 3.53 0.10
BS-268 8 1/2 8 3/4 1/8 8.484 0.050 0.139 0.004 215.49 1.27 3.53 0.10
BS-269 8 3/4 9 1/8 8.734 0.050 0.139 0.004 221.84 1.27 3.53 0.10
BS-270 9 9 1/4 1/8 8.984 0.050 0.139 0.004 228.19 1.27 3.53 0.10
BS-271 9 1/4 9 1/2 1/8 9.234 0.055 0.139 0.004 234.54 1.40 3.53 0.10
BS-272 9 1/2 9 3/4 1/8 9.484 0.055 0.139 0.004 240.89 1.40 3.53 0.10
BS-273 9 3/4 10 1/8 9.734 0.055 0.139 0.004 247.24 1.40 3.53 0.10
BS-274 10 10 1/4 1/8 9.984 0.055 0.139 0.004 253.59 1.40 3.53 0.10
BS-275 10 1/2 10 3/4 1/8 10.484 0.055 0.139 0.004 266.29 1.40 3.53 0.10
BS-276 11 11 1/4 1/8 10.984 0.065 0.139 0.004 278.99 1.65 3.53 0.10
BS-277 11 1/2 11 3/4 1/8 11.484 0.065 0.139 0.004 291.69 1.65 3.53 0.10
BS-278 12 12 1/4 1/8 11.984 0.065 0.139 0.004 304.39 1.65 3.53 0.10
BS-279 13 13 1/4 1/8 12.984 0.065 0.139 0.004 329.79 1.65 3.53 0.10
BS-280 14 14 1/4 1/8 13.984 0.065 0.139 0.004 355.19 1.65 3.53 0.10
BS-281 15 15 1/4 1/8 14.984 0.065 0.139 0.004 380.59 1.65 3.53 0.10
BS-282 16 16 1/4 1/8 15.955 0.075 0.139 0.004 405.26 1.91 3.53 0.10
BS-283 17 17 1/4 1/8 16.955 0.080 0.139 0.004 430.66 2.03 3.53 0.10
BS-284 18 18 1/4 1/8 17.955 0.085 0.139 0.004 456.06 2.16 3.53 0.10
BS-309 7/16 13/16 3/16 0.412 0.005 0.210 0.005 10.46 0.13 5.33 0.13
BS-310 1/2 7/8 3/16 0.475 0.005 0.210 0.005 12.07 0.13 5.33 0.13
BS-311 9/16 15/16 3/16 0.537 0.007 0.210 0.005 13.64 0.18 5.33 0.13
BS-312 5/8 1 3/16 0.600 0.009 0.210 0.005 15.24 0.23 5.53 0.13
BS-313 11/16 1 1/16 3/16 0.662 0.009 0.210 0.005 16.81 0.23 5.33 0.13
Klinger Acorn

BS-314 3/4 1 1/8 3/16 0.725 0.010 0.210 0.005 18.42 0.25 5.33 0.13
BS-315 13/16 1 3/16 3/16 0.787 0.010 0.210 0.005 19.99 0.25 5.33 0.13
BS-316 7/8 1 1/4 3/16 0.85 0.010 0.210 0.005 21.59 0.25 5.33 0.13
BS-317 15/16 1 5/16 3/16 0.912 0.010 0.210 0.005 23.16 0.25 5.33 0.13
BS-318 1 1 3/8 3/16 0.975 0.010 0.210 0.005 24.77 0.25 5.53 0.13
BS-319 1 1/16 1 7/16 3/16 1.037 0.010 0.210 0.005 26.34 0.25 5.33 0.13
BS-320 1 1/8 1 1/2 3/16 1.100 0.012 0.210 0.005 27.94 0.30 5.33 0.13
BS-321 1 3/16 1 9/16 3/16 1.162 0.012 0.210 0.005 29.51 0.30 5.33 0.13
BS-322 1 1/4 1 5/8 3/16 1.225 0.012 0.210 0.005 31.12 0.30 5.33 0.13
BS-323 1 5/16 1 11/16 3/16 1.287 0.012 0.210 0.005 32.69 0.30 5.53 0.13
BS-324 1 3/8 1 3/4 3/16 1.350 0.012 0.210 0.005 34.29 0.30 5.33 0.13
BS-325 1 1/2 1 7/8 3/16 1.475 0.015 0.210 0.005 37.47 0.38 5.33 0.13
BS-326 1 5/8 2 3/16 1.600 0.015 0.210 0.005 40.64 0.38 5.33 0.13
BS-327 1 3/4 2 1/8 3/16 1.725 0.015 0.210 0.005 43.82 0.38 5.33 0.13

250
Telephone : 01274 - 688222
 Fax
E-mail
: 01274 - 688549
: [email protected]
 O-RING REFERENCE GUIDE
Nominal Size (inches) Standard O-Ring Size (Inches) Metric O-Ring Size (mm)
O-Ring
Reference Inches Actual Per AS 568A Actual Per AS 568A
number
ID OD W ID +/- W +/- ID +/- W +/-
BS-328 1 7/8 2 1/4 3/16 1.850 0.015 0.210 0.005 46.99 0.38 5.53 0.13
BS-329 2 2 3/8 3/16 1.975 0.018 0.210 0.005 50.17 0.46 5.33 0.13
BS-330 2 1/8 2 1/2 3/16 2.100 0.018 0.210 0.005 53.34 0.46 5.33 0.13
BS-331 2 1/4 2 5/8 3/16 2.225 0.018 0.210 0.005 56.52 0.46 5.33 0.13
BS-332 2 3/8 2 3/4 3/16 2.350 0.018 0.210 0.005 59.69 0.46 5.33 0.13
BS-333 2 1/2 2 7/8 3/16 2.475 0.020 0.210 0.005 62.87 0.51 5.53 0.13
BS-334 2 5/8 3 3/16 2.600 0.020 0.210 0.005 66.04 0.51 5.33 0.13
BS-335 2 3/4 3 1/8 3/16 2.725 0.020 0.210 0.005 69.22 0.51 5.33 0.13
BS-336 2 7/8 3 1/4 3/16 2.850 0.020 0.210 0.005 72.39 0.51 5.33 0.13
BS-337 3 3 3/8 3/16 2.975 0.024 0.210 0.005 75.57 0.61 5.33 0.13
BS-338 3 1/8 3 1/2 3/16 3.100 0.024 0.210 0.005 78.74 0.61 5.53 0.13
BS-339 3 1/4 3 5/8 3/16 3.225 0.024 0.210 0.005 81.92 0.61 5.33 0.13
BS-340 3 3/8 3 3/4 3/16 3.350 0.024 0.210 0.005 85.09 0.61 5.33 0.13
BS-341 3 1/2 3 7/8 3/16 3.475 0.024 0.210 0.005 88.27 0.61 5.33 0.13
BS-342 3 5/8 4 3/16 3.600 0.028 0.210 0.005 91.44 0.71 5.33 0.13
BS-343 3 3/4 4 1/8 3/16 3.725 0.028 0.210 0.005 94.62 0.71 5.53 0.13
BS-344 3 7/8 4 1/4 3/16 3.850 0.028 0.210 0.005 97.79 0.71 5.33 0.13
BS-345 4 4 3/8 3/16 3.975 0.028 0.210 0.005 100.97 0.71 5.33 0.13
BS-346 4 1/8 4 1/2 3/16 4.100 0.028 0.210 0.005 104.14 0.71 5.33 0.13
BS-347 4 1/4 4 5/8 3/16 4.225 0.030 0.210 0.005 107.32 0.76 5.33 0.13
BS-348 4 3/8 4 3/4 3/16 4.350 0.030 0.210 0.005 110.49 0.76 5.53 0.13
BS-349 4 1/2 4 7/8 3/16 4.475 0.030 0.210 0.005 113.67 0.76 5.33 0.13
BS-350 4 5/8 5 3/16 4.600 0.030 0.210 0.005 116.84 0.76 5.33 0.13
BS-351 4 3/4 5 1/8 3/16 4.725 0.030 0.210 0.005 120.02 0.76 5.33 0.13
BS-352 4 7/8 5 1/4 3/16 4.850 0.030 0.210 0.005 123.19 0.76 5.33 0.13
BS-353 5 5 3/8 3/16 4.975 0.037 0.210 0.005 126.37 0.94 5.33 0.13
BS-354 5 1/8 5 1/2 3/16 5.100 0.037 0.210 0.005 129.54 0.94 5.53 0.13
BS-355 5 1/4 5 5/8 3/16 5.225 0.037 0.210 0.005 132.72 0.94 5.33 0.13
BS-356 5 3/8 5 3/4 3/16 5.350 0.037 0.210 0.005 135.89 0.94 5.33 0.13
BS-357 5 1/2 5 7/8 3/16 5.475 0.037 0.210 0.005 139.07 0.94 5.33 0.13
BS-358 5 5/8 6 3/16 5.600 0.037 0.210 0.005 142.24 0.94 5.33 0.13
BS-359 5 3/4 6 1/8 3/16 5.725 0.037 0.210 0.005 145.42 0.94 5.53 0.13
BS-360 5 7/8 6 1/4 3/16 5.850 0.037 0.210 0.005 148.59 0.94 5.33 0.13

Klinger Acorn
BS-361 6 6 3/8 3/16 5.975 0.037 0.210 0.005 151.77 0.94 5.33 0.13
BS-362 6 1/4 6 5/8 3/16 6.225 0.040 0.210 0.005 158.12 1.02 5.33 0.13
BS-363 6 1/2 6 7/8 3/16 6.475 0.040 0.210 0.005 164.47 1.02 5.33 0.13
BS-364 6 3/4 7 1/8 3/16 6.725 0.040 0.210 0.005 170.82 1.02 5.53 0.13
BS-365 7 7 3/8 3/16 6.975 0.040 0.210 0.005 177.17 1.02 5.33 0.13
BS-366 7 1/4 7 5/8 3/16 7.225 0.045 0.210 0.005 183.52 1.14 5.33 0.13
BS-367 7 1/2 7 7/8 3/16 7.475 0.045 0.210 0.005 189.87 1.14 5.33 0.13
BS-368 7 3/4 8 1/8 3/16 7.725 0.045 0.210 0.005 196.22 1.14 5.33 0.13
BS-369 8 8 3/8 3/16 7.975 0.045 0.210 0.005 202.57 1.14 5.53 0.13
BS-370 8 1/4 8 5/8 3/16 8.225 0.050 0.210 0.005 208.92 1.27 5.33 0.13
BS-371 8 1/2 8 7/8 3/16 8.475 0.050 0.210 0.005 215.27 1.27 5.33 0.13
BS-372 8 3/4 9 1/8 3/16 8.725 0.050 0.210 0.005 221.62 1.27 5.33 0.13
BS-373 9 9 3/8 3/16 8.975 0.050 0.210 0.005 227.97 1.27 5.33 0.13

251
Telephone : 01274 - 688222
 Fax
E- mail
: 01274 - 688549
: [email protected]
 O-RING REFERENCE GUIDE
Nominal Size (inches) Standard O-Ring Size (Inches) Metric O-Ring Size (mm)
O-Ring
Reference Inches Actual Per AS 568A Actual Per AS 568A
number
ID OD W ID +/- W +/- ID +/- W +/-
BS-374 9 1/4 9 5/8 3/16 9.225 0.055 0.210 0.005 234.32 1.40 5.53 0.13
BS-375 9 1/2 9 7/8 3/16 9.475 0.055 0.210 0.005 240.67 1.40 5.33 0.13
BS-376 9 3/4 10 1/8 3/16 9.725 0.055 0.210 0.005 247.02 1.40 5.33 0.13
BS-377 10 10 3/8 3/16 9.975 0.055 0.210 0.005 253.37 1.40 5.33 0.13
BS-378 10 1/2 10 7/8 3/16 10.475 0.060 0.210 0.005 266.07 1.52 5.33 0.13
BS-379 11 11 3/8 3/16 10.975 0.060 0.210 0.005 278.77 1.52 5.53 0.13
BS-380 11 1/2 11 7/8 3/16 11.475 0.065 0.210 0.005 291.47 1.65 5.33 0.13
BS-381 12 12 3/8 3/16 11.975 0.065 0.210 0.005 304.17 1.65 5.33 0.13
BS-382 13 13 3/8 3/16 12.975 0.065 0.210 0.005 329.57 1.65 5.33 0.13
BS-383 14 14 3/8 3/16 13.975 0.070 0.210 0.005 354.97 1.78 5.33 0.13
BS-384 15 15 3/8 3/16 14.975 0.070 0.210 0.005 380.37 1.78 5.53 0.13
BS-385 16 16 3/8 3/16 15.955 0.075 0.210 0.005 405.26 1.91 5.33 0.13
BS-386 17 17 3/8 3/16 16.955 0.080 0.210 0.005 430.66 2.03 5.33 0.13
BS-387 18 18 3/8 3/16 17.955 0.085 0.210 0.005 456.06 2.16 5.33 0.13
BS-388 19 19 3/8 3/16 18.955 0.090 0.210 0.005 481.41 2.29 5.33 0.13
BS-389 20 20 3/8 3/16 19.955 0.095 0.210 0.005 506.81 2.41 5.53 0.13
BS-390 21 21 3/8 3/16 20.955 0.095 0.210 0.005 532.21 2.41 5.33 0.13
BS-391 22 22 3/8 3/16 21.955 0.100 0.210 0.005 557.61 2.54 5.33 0.13
BS-392 23 23 3/8 3/16 22.940 0.105 0.210 0.005 582.68 2.67 5.33 0.13
BS-393 24 24 3/8 3/16 23.940 0.110 0.210 0.005 608.08 2.79 5.33 0.13
BS-394 25 25 3/8 3/16 24.940 0.115 0.210 0.005 633.48 2.92 5.33 0.13
BS-395 26 26 3/8 3/16 25.940 0.120 0.210 0.005 658.88 3.05 5.33 0.13
BS-425 4 1/2 5 1/4 4.475 0.033 0.275 0.006 113.67 0.84 6.99 0.15
BS-426 4 5/8 5 1/8 1/4 4.600 0.033 0.275 0.006 116.84 0.84 6.99 0.15
BS-427 4 3/4 5 1/4 1/4 4.725 0.033 0.275 0.006 120.02 0.84 6.99 0.15
BS-428 4 7/8 5 3/8 1/4 4.850 0.033 0.275 0.006 123.19 0.84 6.99 0.15
BS-429 5 5 1/2 1/4 4.975 0.037 0.275 0.006 126.37 0.94 6.99 0.15
BS-430 5 1/8 5 5/8 1/4 5.100 0.037 0.275 0.006 129.54 0.94 6.99 0.15
BS-431 5 1/4 5 3/4 1/4 5.225 0.037 0.275 0.006 132.72 0.94 6.99 0.15
BS-432 5 3/8 5 7/8 1/4 5.350 0.037 0.275 0.006 135.89 0.94 6.99 0.15
BS-433 5 1/2 6 1/4 5.475 0.037 0.275 0.006 139.07 0.94 6.99 0.15
BS-434 5 5/8 6 1/8 1/4 5.600 0.037 0.275 0.006 142.24 0.94 6.99 0.15
Klinger Acorn

BS-435 5 3/4 6 1/4 1/4 5.725 0.037 0.275 0.006 145.42 0.94 6.99 0.15
BS-436 5 7/8 6 3/8 1/4 5.850 0.037 0.275 0.006 148.59 0.94 6.99 0.15
BS-437 6 6 1/2 1/4 5.975 0.037 0.275 0.006 151.77 0.94 6.99 0.15
BS-438 6 1/4 6 3/4 1/4 6.225 0.040 0.275 0.006 158.12 1.02 6.99 0.15
BS-439 6 1/2 7 1/4 6.475 0.040 0.275 0.006 164.47 1.02 6.99 0.15
BS-440 6 3/4 7 1/4 1/4 6.725 0.040 0.275 0.006 170.82 1.02 6.99 0.15
BS-441 7 7 1/2 1/4 6.975 0.040 0.275 0.006 177.17 1.02 6.99 0.15
BS-442 7 1/4 7 3/4 1/4 7.225 0.045 0.275 0.006 183.52 1.14 6.99 0.15
BS-443 7 1/2 8 1/4 7.475 0.045 0.275 0.006 189.87 1.14 6.99 0.15
BS-444 7 3/4 8 1/4 1/4 7.725 0.045 0.275 0.006 196.22 1.14 6.99 0.15
BS-445 8 8 1/2 1/4 7.975 0.045 0.275 0.006 202.57 1.14 6.99 0.15
BS-446 8 1/2 9 1/4 8.475 0.055 0.275 0.006 215.27 1.40 6.99 0.15
BS-447 9 9 1/2 1/4 8.975 0.055 0.275 0.006 227.97 1.40 6.99 0.15
BS-448 9 1/2 10 1/4 9.475 0.055 0.275 0.006 240.67 1.40 6.99 0.15

252
Telephone : 01274 - 688222
 Fax
E-mail
: 01274 - 688549
: [email protected]
 O-RING REFERENCE GUIDE
Nominal Size (inches) Standard O-Ring Size (Inches) Metric O-Ring Size (mm)
O-Ring
Reference Inches Actual Per AS 568A Actual Per AS 568A
number
ID OD W ID +/- W +/- ID +/- W +/-
BS-449 10 10 1/2 1/4 9.975 0.055 0.275 0.006 253.37 1.40 6.99 0.15
BS-450 10 1/2 11 1/4 10.475 0.060 0.275 0.006 266.07 1.52 6.99 0.15
BS-451 11 11 1/2 1/4 10.975 0.060 0.275 0.006 278.77 1.52 6.99 0.15
BS-452 11 1/2 12 1/4 11.475 0.060 0.275 0.006 291.47 1.52 6.99 0.15
BS-453 12 12 1/2 1/4 11.975 0.060 0.275 0.006 304.17 1.52 6.99 0.15
BS-454 12 1/2 13 1/4 12.475 0.060 0.275 0.006 316.87 1.52 6.99 0.15
BS-455 13 13 1/2 1/4 12.975 0.060 0.275 0.006 329.57 1.52 6.99 0.15
BS-456 13 1/2 14 1/4 13.475 0.070 0.275 0.006 342.27 1.78 6.99 0.15
BS-457 14 14 1/2 1/4 13.975 0.070 0.275 0.006 354.97 1.78 6.99 0.15
BS-458 14 1/2 15 1/4 14.475 0.070 0.275 0.006 367.67 1.78 6.99 0.15
BS-459 15 15 1/2 1/4 14.975 0.070 0.275 0.006 380.37 1.78 6.99 0.15
BS-460 15 1/2 16 1/4 15.475 0.070 0.275 0.006 393.07 1.78 6.99 0.15
BS-461 16 16 1/2 1/4 15.955 0.075 0.275 0.006 405.26 1.91 6.99 0.15
BS-462 16 1/2 17 1/4 16.455 0.075 0.275 0.006 417.96 1.91 6.99 0.15
BS-463 17 17 1/2 1/4 16.955 0.080 0.275 0.006 430.66 2.03 6.99 0.15
BS-464 17 1/2 18 1/4 17.455 0.085 0.275 0.006 443.36 2.16 6.99 0.15
BS-465 18 18 1/2 1/4 17.955 0.085 0.275 0.006 456.06 2.16 6.99 0.15
BS-466 18 1/2 19 1/4 18.455 0.085 0.275 0.006 468.76 2.16 6.99 0.15
BS-467 19 19 1/2 1/4 18.955 0.090 0.275 0.006 481.46 2.29 6.99 0.15
BS-468 19 1/2 20 1/4 19.455 0.090 0.275 0.006 494.16 2.29 6.99 0.15
BS-469 20 20 1/2 1/4 19.955 0.095 0.275 0.006 506.86 2.41 6.99 0.15
BS-470 21 21 1/2 1/4 20.955 0.095 0.275 0.006 532.26 2.41 6.99 0.15
BS-471 22 22 1/2 1/4 21.955 0.100 0.275 0.006 557.66 2.54 6.99 0.15
BS-472 23 23 1/2 1/4 22.940 0.105 0.275 0.006 582.68 2.67 6.99 0.15
BS-473 24 24 1/2 1/4 23.940 0.110 0.275 0.006 608.08 2.79 6.99 0.15
BS-474 25 25 1/2 1/4 24.940 0.115 0.275 0.006 633.48 2.92 6.99 0.15
BS-475 26 26 1/2 1/4 25.940 0.120 0.275 0.006 658.88 3.05 6.99 0.15

Klinger Acorn

253
Telephone : 01274 - 688222
 Fax
E- mail
: 01274 - 688549
: [email protected]
 O-RING REFERENCE GUIDE
Straight Thread Tube Fitting O-Ring Dimensions

O-Ring Reference Straight Thread Tube Fitting O-ring Size Metric O-Ring Size (mm)
Number Tube OD ID +/- W +/- ID +/- W +/-
BS-3-901 3/32 0.185 0.005 0.056 0.003 4.70 0.13 1.42 0.08
BS-3-902 1/8 0.239 0.005 0.064 0.003 6.07 0.13 1.63 0.08
BS-3-903 3/16 0.301 0.005 0.064 0.003 7.65 0.13 1.63 0.08
BS-3-904 1/4 0.351 0.005 0.072 0.003 8.92 0.13 1.93 0.08
BS-3-905 5/16 0.414 0.005 0.072 0.003 10.52 0.13 1.93 0.08
BS-3-906 3/8 0.468 0.005 0.078 0.003 11.89 0.13 1.98 0.08
BS-3-907 7/16 0.53 0.005 0.082 0.003 13.46 0.13 2.08 0.08
BS-3-908 1/2 0.644 0.009 0.087 0.003 16.36 0.23 2.20 0.08
BS-3-909 9/16 0.706 0.009 0.097 0.003 17.93 0.23 2.46 0.08
BS-3-910 5/8 0.755 0.009 0.097 0.003 19.18 0.23 2.46 0.08
BS-3-911 11/16 0.863 0.009 0.116 0.004 21.92 0.23 2.95 0.10
BS-3-912 3/4 0.924 0.009 0.116 0.004 23.47 0.23 2.95 0.10
BS-3-913 13/16 0.986 0.010 0.116 0.004 25.04 0.25 2.95 0.10
BS-3-914 7/8 1.047 0.010 0.116 0.004 26.62 0.25 2.95 0.10
BS-3-916 1 1.171 0.010 0.116 0.004 29.74 0.25 2.95 0.10
BS-3-918 1 1/8 1.355 0.012 0.116 0.004 34.42 0.30 2.95 0.10
BS-3-920 1 1/4 1.475 0.014 0.118 0.004 37.47 0.36 3.00 0.10
BS-3-924 1 1/2 1.72 0.014 0.118 0.004 43.69 0.36 3.00 0.10
BS-3-928 1 3/4 2.09 0.018 0.118 0.004 53.09 0.46 3.00 0.10
BS-3-932 2 2.337 0.018 0.118 0.004 59.36 0.46 3.00 0.10
Klinger Acorn

254
Telephone : 01274 - 688222
 Fax
E-mail
: 01274 - 688549
: [email protected]
 O-RING REFERENCE GUIDE
Non-Standard O-Ring Dimensions
O-Ring Cross O-Ring Cross O-Ring Cross
Inside Dia Inside Dia Inside Dia
Reference Section Reference Section Reference Section
(mm) (mm) (mm)
Number (mm) Number (mm) Number (mm)
BS 606 1.78 1.02 BS 824 39.69 3.53 BS 360A 149.23 5.34
BS 607 2.54 1.02 BS 825 41.28 3.53 BS 870 149.23 5.34
BS 801 3.17 1.78 BS 826 42.86 3.53 BS 361A 155.00 5.34
BS 802 4.76 1.78 BS 827 44.45 3.53 BS 644 155.00 5.34
BS 803 6.35 1.78 BS 828 46.04 3.53 BS 362A 161.30 5.34
BS 610 6.75 1.78 BS 829 47.63 3.53 BS 645 161.30 5.34
BS 804 7.94 1.78 BS 830 49.21 3.53 BS 363A 167.70 5.34
BS 611 8.73 1.78 BS 831 50.80 3.53 BS 646 167.70 5.34
BS 806 11.11 1.78 BS 832 52.39 3.53 BS 624 114.70 6.99
BS 517 36.27 1.78 BS 833 53.98 3.53 BS 647 174.00 6.99
BS 519 39.45 1.78 BS 834 55.56 3.53 BS 625 124.60 6.99
BS 532 79.00 1.78 BS 835 57.15 3.53 BS 626 134.50 6.99
BS 534 85.34 1.78 BS 836 58.74 3.53 BS 872 155.60 6.99
BS 536 91.70 1.78 BS 837 60.33 3.53 BS 627 159.50 6.99
BS 538 98.05 1.78 BS 838 61.90 3.53 BS 874 161.90 6.99
BS 540 104.40 1.78 BS 839 63.50 3.53 BS 628 166.70 6.99
BS 542 110.74 1.78 BS 840 65.10 3.53 BS 876 168.30 6.99
BS 544 117.10 1.78 BS 841 66.67 3.53 BS 878 174.60 6.99
BS 546 123.44 1.78 BS 842 68.26 3.53 BS 441A 181.00 6.99
BS 548 129.40 1.78 BS 843 69.85 3.53 BS 880 181.00 6.99
BS 550 135.76 1.78 BS 844 71.44 3.53 BS 442A 187.30 6.99
BS 551 138.94 1.78 BS 845 73.02 3.53 BS 882 187.30 6.99
BS 552 142.11 1.78 BS 846 74.60 3.53 BS 443A 193.70 6.99
BS 553 145.29 1.78 BS 619 74.63 5.34 BS 884 193.70 6.99
BS 554 148.46 1.78 BS 620 79.77 5.34 BS 444A 200.00 6.99
BS 555 151.64 1.78 BS 621 89.69 5.34 BS 886 200.00 6.99
BS 556 154.81 1.78 BS 622 100.00 5.34 BS 445A 208.92 6.99
BS 557 158.00 1.78 BS 623 109.54 5.34 BS 674 208.92 6.99
BS 558 161.16 1.78 BS 350A 117.48 5.34 BS 446A 221.62 6.99
BS 559 164.34 1.78 BS 860 117.48 5.34 BS 676 221.62 6.99
BS 560 167.51 1.78 BS 351A 120.70 5.34 BS 447A 234.32 6.99
BS 561 170.69 1.78 BS 861 120.70 5.34 BS 678 234.32 6.99
BS 562 173.87 1.78 BS 352A 123.83 5.34 BS 448A 247.00 6.99
BS 613 9.92 2.62 BS 862 123.83 5.34 BS 680 247.00 6.99
BS 614 11.91 2.62 BS 353A 127.00 5.34 BS 449A 259.70 6.99

Klinger Acorn
BS 807 12.70 2.62 BS 863 127.00 5.34 BS 682 259.70 6.99
BS 615 13.10 2.62 BS 354A 130.18 5.34 BS 450A 272.40 6.99
BS 616 15.08 2.62 BS 864 130.18 5.34 BS 684 272.40 6.99
BS 809 15.88 2.62 BS 355A 133.35 5.34 BS 451A 285.10 6.99
BS 810 17.46 2.62 BS 865 133.35 5.34 BS 686 285.10 6.99
BS 617 17.86 2.62 BS 356A 136.53 5.34 BS 452A 297.80 6.99
BS 812 20.63 2.62 BS 866 136.53 5.34 BS 688 297.47 6.99
BS 813 22.22 2.62 BS 357A 139.70 5.34 BS 453A 310.50 6.99
BS 814 23.81 2.62 BS 867 139.70 5.34 BS 648 310.50 6.99
BS 641 77.50 2.62 BS 358A 142.88 5.34 BS 649 323.20 6.99
BS 642 80.60 2.62 BS 868 142.88 5.34 BS 650 335.90 6.99
BS 643 83.80 2.62 BS 359A 146.05 5.34
BS 618 25.80 3.53 BS 869 146.05 5.34

255
Telephone : 01274 - 688222
 Fax
E- mail
: 01274 - 688549
: [email protected]
 O-RING BACK-UP RINGS

Introduction
Back-Up Rings are a polymer or rubber ring used to prevent
the O-Ring from entering the extrusion gap. In high pressure
applications the soft rubber O-Ring material can be forced
into the extrusion gap which can cause the O-Ring to fail.
The harder Back-Up Ring material will prevent the O-Ring
from extruding and help prevent premature degradation.
Contoured Back-up Rings
Contoured Back-Up Rings are predominately manufactured
from moulded 90° Durometer Nitrile or Viton with a contour
on one face where contact is made with the O-Ring.
I.D
Back-Up Rings are specifically designed to be used in
A A conjunction with an O-Ring to prevent extrusion of the
O-Ring in machined grooves. They can be used on either
Depth one or on both sides of the O-Ring for bidirectional pressure.
A Both options are simple to install.

We would recommend the use of Contoured Back-Up Rings

when the hydraulic pressure exceeds 100bar. Additional
Width
Radius benefits of Back-Up Rings are broader allowable machining
tolerances and also provide improved clearance of mating
parts.

We stock all standard Nitrile 90° Durometer Contoured Back-

A-A
R0.010" MAX Up Rings, along with the most commonly used sizes in Viton
Contoured rubber.

All parts are supplied with batch numbers and cure dates.

I.D
All sizes correspond to the BS & AS568 O-Rings sizes with
which they are used.
Availability
Klinger Acorn

Scarf-Cut
Contoured Back-Up Rings are manufactured from 90°
Durometer Nitrile, but also Viton is available in many sizes.

Scarf-Cut, Spiral-Cut and Butt-Cut Back-Up Rings are

only available in PTFE. These styles of back-up rings aid
installation. We also supply solid flat back-up rings.
I.D

Spiral-Cut

256
Telephone : 01274 - 688222
 Fax
E-mail
: 01274 - 688549
: [email protected]
 CONTOURED BACK-UP RING REFERENCE GUIDE
Ref I.D. Width Radius A. Depth, D Ref I.D. Width Radius A. Depth, D
CB-004 0.096 0.053 0.087 0.045 0.049 CB-115 0.702 0.086 0.129 0.045 0.053
CB-005 0.127 0.053 0.087 0.045 0.049 CB-116 0.765 0.086 0.129 0.045 0.053
CB-006 0.140 0.053 0.087 0.045 0.049 CB-117 0.831 0.086 0.129 0.045 0.053
CB-007 0.171 0.053 0.087 0.045 0.049 CB-118 0.893 0.086 0.129 0.045 0.053
CB-008 0.202 0.053 0.087 0.045 0.049 CB-119 0.956 0.086 0.129 0.045 0.053
CB-009 0.234 0.053 0.087 0.045 0.049 CB-120 1.018 0.086 0.129 0.045 0.053
CB-010 0.265 0.053 0.087 0.045 0.049 CB-121 1.081 0.086 0.129 0.045 0.053
CB-011 0.327 0.053 0.087 0.045 0.049 CB-122 1.143 0.086 0.129 0.045 0.053
CB-012 0.390 0.053 0.087 0.045 0.049 CB-123 1.206 0.086 0.129 0.045 0.053
CB-013 0.455 0.053 0.087 0.045 0.049 CB-124 1.268 0.086 0.129 0.045 0.053
CB-014 0.518 0.053 0.087 0.045 0.049 CB-125 1.331 0.086 0.129 0.045 0.053
CB-015 0.580 0.053 0.087 0.045 0.049 CB-126 1.393 0.086 0.129 0.045 0.053
CB-016 0.643 0.053 0.087 0.045 0.049 CB-127 1.456 0.086 0.129 0.045 0.053
CB-017 0.705 0.053 0.087 0.045 0.049 CB-128 1.518 0.086 0.129 0.045 0.053
CB-018 0.768 0.053 0.087 0.045 0.049 CB-129 1.581 0.086 0.129 0.045 0.053
CB-019 0.893 0.053 0.087 0.045 0.049 CB-130 1.643 0.086 0.129 0.045 0.053
CB-020 0.893 0.053 0.087 0.045 0.049 CB-131 1.706 0.086 0.129 0.045 0.053
CB-021 0.955 0.053 0.087 0.045 0.049 CB-132 1.768 0.086 0.129 0.045 0.053
CB-022 1.018 0.053 0.087 0.045 0.049 CB-133 1.831 0.086 0.129 0.045 0.053
CB-023 1.080 0.053 0.087 0.045 0.049 CB-134 1.893 0.086 0.129 0.045 0.053
CB-024 1.143 0.053 0.087 0.045 0.049 CB-135 1.956 0.086 0.129 0.045 0.053
CB-025 1.205 0.053 0.087 0.045 0.049 CB-136 2.018 0.086 0.129 0.045 0.053
CB-026 1.268 0.053 0.087 0.045 0.049 CB-137 2.081 0.086 0.129 0.045 0.053
CB-027 1.330 0.053 0.087 0.045 0.049 CB-138 2.143 0.086 0.129 0.045 0.053
CB-028 1.393 0.053 0.087 0.045 0.049 CB-139 2.206 0.086 0.129 0.045 0.053
CB-029 1.518 0.053 0.087 0.045 0.049 CB-140 2.268 0.086 0.129 0.045 0.053
CB-030 1.643 0.053 0.087 0.045 0.049 CB-141 2.331 0.086 0.129 0.045 0.053
CB-031 1.768 0.053 0.087 0.045 0.049 CB-142 2.393 0.086 0.129 0.045 0.053
CB-032 1.893 0.053 0.087 0.045 0.049 CB-143 2.456 0.086 0.129 0.045 0.053
CB-033 2.018 0.053 0.087 0.045 0.049 CB-144 2.528 0.086 0.129 0.045 0.053
CB-034 2.143 0.053 0.087 0.045 0.049 CB-150 2.893 0.086 0.129 0.045 0.053
CB-035 2.268 0.053 0.087 0.045 0.049 CB-151 3.018 0.086 0.129 0.045 0.053
CB-036 2.393 0.053 0.087 0.045 0.049 CB-152 3.268 0.086 0.129 0.045 0.053
CB-037 2.519 0.053 0.087 0.045 0.049 CB-153 3.518 0.086 0.129 0.045 0.053
CB-038 2.643 0.053 0.087 0.045 0.049 CB-154 3.768 0.086 0.129 0.045 0.053
CB-039 2.768 0.053 0.087 0.045 0.049 CB-155 4.018 0.086 0.129 0.045 0.053
CB-040 2.893 0.053 0.087 0.045 0.049 CB-156 4.268 0.086 0.129 0.045 0.053
CB-041 3.018 0.053 0.087 0.045 0.049 CB-157 4.518 0.086 0.129 0.045 0.053
CB-042 3.518 0.053 0.087 0.045 0.049 CB-158 4.768 0.086 0.129 0.045 0.053
CB-043 3.518 0.053 0.087 0.045 0.049 CB-159 5.018 0.086 0.129 0.045 0.053
CB-044 3.768 0.053 0.087 0.045 0.049 CB-160 5.268 0.086 0.129 0.045 0.053
CB-045 4.018 0.053 0.087 0.045 0.049 CB-161 5.518 0.086 0.129 0.045 0.053
CB-046 4.268 0.053 0.087 0.045 0.049 CB-162 5.768 0.086 0.129 0.045 0.053
CB-047 4.518 0.053 0.087 0.045 0.049 CB-163 6.018 0.086 0.129 0.045 0.053
CB-048 4.768 0.053 0.087 0.045 0.049 CB-164 6.268 0.086 0.129 0.045 0.053

Klinger Acorn
CB-049 5.018 0.053 0.087 0.045 0.049 CB-165 6.518 0.086 0.129 0.045 0.053
CB-050 5.268 0.053 0.087 0.045 0.049 CB-166 6.768 0.086 0.129 0.045 0.053
CB-102 0.077 0.086 0.129 0.045 0.053 CB-167 7.018 0.086 0.129 0.045 0.053
CB-103 0.109 0.086 0.129 0.045 0.053 CB-168 7.268 0.086 0.129 0.045 0.053
CB-104 0.140 0.086 0.129 0.045 0.053 CB-169 7.518 0.086 0.129 0.045 0.053
CB-105 0.171 0.086 0.129 0.045 0.053 CB-170 7.768 0.086 0.129 0.045 0.053
CB-106 0.202 0.086 0.129 0.045 0.053 CB-171 8.018 0.086 0.129 0.045 0.053
CB-107 0.234 0.086 0.129 0.045 0.053 CB-172 8.268 0.086 0.129 0.045 0.053
CB-108 0.265 0.086 0.129 0.045 0.053 CB-173 8.518 0.086 0.129 0.045 0.053
CB-109 0.327 0.086 0.129 0.045 0.053 CB-174 8.768 0.086 0.129 0.045 0.053
CB-110 0.390 0.086 0.129 0.045 0.053 CB-175 9.018 0.086 0.129 0.045 0.053
CB-111 0.452 0.086 0.129 0.045 0.053 CB-176 9.268 0.086 0.129 0.045 0.053
CB-112 0.515 0.086 0.129 0.045 0.053 CB-177 9.518 0.086 0.129 0.045 0.053
CB-113 0.577 0.086 0.129 0.045 0.053 CB-178 9.768 0.086 0.129 0.045 0.053
CB-114 0.640 0.086 0.129 0.045 0.053 CB-201 0.202 0.118 0.174 0.040 0.050

All dimensions in inches

257
Telephone : 01274 - 688222
 Fax
E- mail
: 01274 - 688549
: [email protected]
 CONTOURED BACK-UP RING REFERENCE GUIDE
Ref I.D. Width Radius A. Depth, D Ref I.D. Width Radius A. Depth, D
CB-202 0.265 0.118 0.174 0.040 0.050 CB-262 7.018 0.118 0.174 0.040 0.050
CB-203 0.327 0.118 0.174 0.040 0.050 CB-263 7.268 0.118 0.174 0.040 0.050
CB-204 0.390 0.118 0.174 0.040 0.050 CB-264 7.518 0.118 0.174 0.040 0.050
CB-205 0.455 0.118 0.174 0.040 0.050 CB-265 7.768 0.118 0.174 0.040 0.050
CB-206 0.518 0.118 0.174 0.040 0.050 CB-266 8.018 0.118 0.174 0.040 0.050
CB-207 0.580 0.118 0.174 0.040 0.050 CB-267 8.268 0.118 0.174 0.040 0.050
CB-208 0.643 0.118 0.174 0.040 0.050 CB-268 8.518 0.118 0.174 0.040 0.050
CB-209 0.705 0.118 0.174 0.040 0.050 CB-269 8.768 0.118 0.174 0.040 0.050
CB-210 0.765 0.118 0.174 0.040 0.050 CB-270 9.018 0.118 0.174 0.040 0.050
CB-211 0.828 0.118 0.174 0.040 0.050 CB-271 9.268 0.118 0.174 0.040 0.050
CB-212 0.891 0.118 0.174 0.040 0.050 CB-272 9.518 0.118 0.174 0.040 0.050
CB-213 0.953 0.118 0.174 0.040 0.050 CB-273 9.768 0.118 0.174 0.040 0.050
CB-214 1.016 0.118 0.174 0.040 0.050 CB-274 10.018 0.118 0.174 0.040 0.050
CB-215 1.078 0.118 0.174 0.040 0.050 CB-275 10.518 0.118 0.174 0.040 0.050
CB-216 1.141 0.118 0.174 0.040 0.050 CB-276 11.018 0.118 0.174 0.040 0.050
CB-217 1.203 0.118 0.174 0.040 0.050 CB-277 11.518 0.118 0.174 0.040 0.050
CB-218 1.266 0.118 0.174 0.040 0.050 CB-278 12.018 0.118 0.174 0.040 0.050
CB-219 1.334 0.118 0.174 0.040 0.050 CB-279 13.018 0.118 0.174 0.040 0.050
CB-220 1.397 0.118 0.174 0.040 0.050 CB-280 14.018 0.118 0.174 0.040 0.050
CB-221 1.459 0.118 0.174 0.040 0.050 CB-281 15.018 0.118 0.174 0.040 0.050
CB-222 1.522 0.118 0.174 0.040 0.050 CB-282 15.989 0.118 0.174 0.040 0.050
CB-223 1.647 0.118 0.174 0.040 0.050 CB-283 16.989 0.118 0.174 0.040 0.050
CB-224 1.772 0.118 0.174 0.040 0.050 CB-284 17.989 0.118 0.174 0.040 0.050
CB-225 1.897 0.118 0.174 0.040 0.050 CB-309 0.450 0.183 0.262 0.060 0.076
CB-226 2.022 0.118 0.174 0.040 0.050 CB-310 0.513 0.183 0.262 0.060 0.076
CB-227 2.147 0.118 0.174 0.040 0.050 CB-311 0.575 0.183 0.262 0.060 0.076
CB-228 2.272 0.118 0.174 0.040 0.050 CB-312 0.638 0.183 0.262 0.060 0.076
CB-229 2.397 0.118 0.174 0.040 0.050 CB-313 0.700 0.183 0.262 0.060 0.076
CB-230 2.522 0.118 0.174 0.040 0.050 CB-314 0.763 0.183 0.262 0.060 0.076
CB-231 2.631 0.118 0.174 0.040 0.050 CB-315 0.825 0.183 0.262 0.060 0.076
CB-232 2.756 0.118 0.174 0.040 0.050 CB-316 0.888 0.183 0.262 0.060 0.076
CB-233 2.881 0.118 0.174 0.040 0.050 CB-317 0.950 0.183 0.262 0.060 0.076
CB-234 3.006 0.118 0.174 0.040 0.050 CB-318 1.103 0.183 0.262 0.060 0.076
CB-235 3.131 0.118 0.174 0.040 0.050 CB-319 1.075 0.183 0.262 0.060 0.076
CB-236 3.256 0.118 0.174 0.040 0.050 CB-320 1.138 0.183 0.262 0.060 0.076
CB-237 3.381 0.118 0.174 0.040 0.050 CB-321 1.200 0.183 0.262 0.060 0.076
CB-238 3.506 0.118 0.174 0.040 0.050 CB-322 1.263 0.183 0.262 0.060 0.076
CB-239 3.631 0.118 0.174 0.040 0.050 CB-323 1.316 0.183 0.262 0.060 0.076
CB-240 3.756 0.118 0.174 0.040 0.050 CB-324 1.388 0.183 0.262 0.060 0.076
CB-241 3.881 0.118 0.174 0.040 0.050 CB-325 1.513 0.183 0.262 0.060 0.076
CB-242 4.006 0.118 0.174 0.040 0.050 CB-326 1.638 0.183 0.262 0.060 0.076
CB-243 4.131 0.118 0.174 0.040 0.050 CB-327 1.763 0.183 0.262 0.060 0.076
CB-244 4.256 0.118 0.174 0.040 0.050 CB-328 1.888 0.183 0.262 0.060 0.076
CB-245 4.381 0.118 0.174 0.040 0.050 CB-329 2.013 0.183 0.262 0.060 0.076
Klinger Acorn

CB-246 4.506 0.118 0.174 0.040 0.050 CB-330 2.138 0.183 0.262 0.060 0.076
CB-247 4.631 0.118 0.174 0.040 0.050 CB-331 2.268 0.183 0.262 0.060 0.076
CB-248 4.768 0.118 0.174 0.040 0.050 CB-332 2.393 0.183 0.262 0.060 0.076
CB-249 4.893 0.118 0.174 0.040 0.050 CB-333 2.518 0.183 0.262 0.060 0.076
CB-250 5.018 0.118 0.174 0.040 0.050 CB-334 2.643 0.183 0.262 0.060 0.076
CB-251 5.143 0.118 0.174 0.040 0.050 CB-335 2.768 0.183 0.262 0.060 0.076
CB-252 5.268 0.118 0.174 0.040 0.050 CB-336 2.893 0.183 0.262 0.060 0.076
CB-253 5.393 0.118 0.174 0.040 0.050 CB-337 3.018 0.183 0.262 0.060 0.076
CB-254 5.518 0.118 0.174 0.040 0.050 CB-338 3.143 0.183 0.262 0.060 0.076
CB-255 5.643 0.118 0.174 0.040 0.050 CB-339 3.273 0.183 0.262 0.060 0.076
CB-256 5.768 0.118 0.174 0.040 0.050 CB-340 3.398 0.183 0.262 0.060 0.076
CB-257 5.893 0.118 0.174 0.040 0.050 C8-341 3.523 0.183 0.262 0.060 0.076
CB-258 6.018 0.118 0.174 0.040 0.050 CB-342 3.648 0.183 0.262 0.060 0.076
CB-259 6.268 0.118 0.174 0.040 0.050 CB-343 3.773 0.183 0.262 0.060 0.076
CB-260 6.518 0.118 0.174 0.040 0.050 CB-344 3.898 0.183 0.262 0.060 0.076
CB-261 6.768 0.118 0.174 0.040 0.050 CB-345 4.028 0.183 0.262 0.060 0.076

All dimensions in inches

258
Telephone : 01274 - 688222
 Fax
E-mail
: 01274 - 688549
: [email protected]
 CONTOURED BACK-UP RING REFERENCE GUIDE
Ref I.D. Width Radius A. Depth, D Ref I.D. Width Radius A. Depth, D
CB-346 4.153 0.183 0.262 0.060 0.076 CB-435 5.801 0.236 0.344 0.096 0.117
CB-347 4.278 0.183 0.262 0.060 0.076 CB-436 5.926 0.236 0.344 0.096 0.117
CB-348 4.403 0.183 0.262 0.060 0.076 CB-437 6.051 0.236 0.344 0.096 0.117
CB-349 4.528 0.183 0.262 0.060 0.076 CB-438 6.274 0.236 0.344 0.096 0.117
CB-350 4.653 0.183 0.262 0.060 0.076 CB-439 6.525 0.236 0.344 0.096 0.117
CB-351 4.778 0.183 0.262 0.060 0.076 CB-440 6.774 0.236 0.344 0.096 0.117
CB-352 4.903 0.183 0.262 0.060 0.076 CB-441 7.024 0.236 0.344 0.096 0.117
CB-353 5.028 0.183 0.262 0.060 0.076 CB-442 7.274 0.236 0.344 0.096 0.117
CB-354 5.153 0.183 0.262 0.060 0.076 CB-443 7.524 0.236 0.344 0.096 0.117
CB-355 5.278 0.183 0.262 0.060 0.076 CB-444 7.774 0.236 0.344 0.096 0.117
CB-356 5.403 0.183 0.262 0.060 0.076 CB-445 8.024 0.236 0.344 0.096 0.117
CB-357 5.528 0.183 0.262 0.060 0.076 CB-446 8.524 0.236 0.344 0.096 0.117
CB-358 5.653 0.183 0.262 0.060 0.076 CB-447 9.024 0.236 0.344 0.096 0.117
CB-359 5.778 0.183 0.262 0.060 0.076 CB-448 9.524 0.236 0.344 0.096 0.117
CB-360 5.903 0.183 0.262 0.060 0.076 CB-449 10.024 0.236 0.344 0.096 0.117
CB-361 6.028 0.183 0.262 0.060 0.076 CB-450 10.524 0.236 0.236 0.096 0.117
CB-362 6.278 0.183 0.262 0.060 0.076 CB-451 11.024 0.236 0.236 0.096 0.117
CB-363 6.528 0.183 0.262 0.060 0.076 CB-452 11.524 0.236 0.236 0.096 0.117
CB-364 6.778 0.183 0.262 0.060 0.076 CB-453 12.024 0.236 0.236 0.096 0.117
CB-365 7.028 0.183 0.262 0.060 0.076 CB-454 12.524 0.236 0.236 0.096 0.117
CB-366 7.278 0.183 0.262 0.060 0.076 CB-455 13.024 0.236 0.236 0.096 0.117
CB-367 7.528 0.183 0.262 0.060 0.076 CB-456 13.524 0.236 0.236 0.096 0.117
CB-368 7.778 0.183 0.262 0.060 0.076 CB-457 14.024 0.236 0.236 0.096 0.117
CB-369 8.028 0.183 0.262 0.060 0.076 CB-458 14.524 0.236 0.236 0.096 0.117
CB-370 8.278 0.183 0.262 0.060 0.076 CB-459 15.024 0.236 0.236 0.096 0.117
CB-371 8.528 0.183 0.262 0.060 0.076 CB-460 15.524 0.236 0.236 0.096 0.117
CB-372 8.778 0.183 0.262 0.060 0.076 CB-461 16.004 0.236 0.236 0.096 0.117
CB-373 9.028 0.183 0.262 0.060 0.076 CB-462 16.504 0.236 0.236 0.096 0.117
CB-374 9.278 0.183 0.262 0.060 0.076 CB-463 17.004 0.236 0.236 0.096 0.117
CB-375 9.528 0.183 0.262 0.060 0.076 CB-464 17.504 0.236 0.236 0.096 0.117
CB-376 9.778 0.183 0.262 0.060 0.076 CB-465 18.004 0.236 0.236 0.096 0.117
CB-377 10.028 0.183 0.262 0.060 0.076 CB-466 18.504 0.236 0.236 0.096 0.117
CB-378 10.528 0.183 0.262 0.060 0.076 CB-467 19.004 0.236 0.236 0.096 0.117
CB-379 11.028 0.183 0.262 0.060 0.076 CB-468 19.504 0.236 0.236 0.096 0.117
CB-380 11.528 0.183 0.262 0.060 0.076 CB-469 20.004 0.236 0.236 0.096 0.117
CB-381 12.028 0.183 0.262 0.060 0.076 CB-470 21.004 0.236 0.236 0.096 0.117
CB-382 13.028 0.183 0.262 0.060 0.076 CB-471 22.004 0.236 0.236 0.096 0.117
CB-383 14.028 0.183 0.262 0.060 0.076 CB-472 23.004 0.236 0.236 0.096 0.117
CB-384 15.028 0.183 0.262 0.060 0.076 CB-473 24.004 0.236 0.236 0.096 0.117
CB-385 16.008 0.183 0.262 0.060 0.076 CB-474 25.004 0.236 0.236 0.096 0.117
CB-386 17.008 0.183 0.262 0.060 0.076 CB-475 26.004 0.236 0.236 0.096 0.117
CB-387 18.008 0.183 0.262 0.060 0.076
CB-388 19.006 0.183 0.262 0.060 0.076
CB-389 20.006 0.183 0.262 0.060 0.076
CB-390 21.006 0.183 0.262 0.060 0.076

Klinger Acorn
CB-391 22.006 0.183 0.262 0.060 0.076
CB-392 22.993 0.183 0.262 0.060 0.076
CB-393 23.993 0.183 0.262 0.060 0.076
CB-394 24.930 0.183 0.262 0.060 0.076
CB-395 25.993 0.183 0.262 0.060 0.076
CB-425 4.551 0.236 0.344 0.096 0.117
CB-426 4.676 0.236 0.344 0.096 0.117
CB-427 4.801 0.236 0.344 0.096 0.117
CB-428 4.926 0.236 0.344 0.096 0.117
CB-429 5.051 0.236 0.344 0.096 0.117
CB-430 5.176 0.236 0.344 0.096 0.117
CB-431 5.301 0.236 0.344 0.096 0.117
CB-432 5.426 0.236 0.344 0.096 0.117
CB-433 5.551 0.236 0.344 0.096 0.117
CB-434 5.676 0.236 0.344 0.096 0.117

All dimensions in inches

259
Telephone : 01274 - 688222
 Fax
E- mail
: 01274 - 688549
: [email protected]