Alpha series - Front end cylinder with single eye
FE A149-3-03830-009-K1645-HD Item no. 70535210
Tipping weight 63 - 84 ton
* incl. 20 [-5; +30] mm pull out 3D model is available on request
Specifications Max. pump flow Tipping time
Max. working pressure 250 bar With KO¹ 220 L/min With KO¹ 14 sec
Weight 168 kg Without KO¹ 190 L/min Without KO¹ 16 sec
Working volume 51 L With KO¹ below -20°C 154 L/min With KO¹ below -20°C 20 sec
Total volume 55 L Without KO¹ below -20°C 133 L/min Without KO¹ below -20°C 23 sec
Max. cyl. load (start tipping) 345 kN Allowable lowering time 11 sec
Extension 1 2 3 4 5 6 7 Total
Effective diameter [mm] 149 129 110
Stroke* [mm] 1260 1285 1285 3830
Technical notes
This cylinder is a lifting device only. It should not be used as a structural member and should not be subjected to side loads. Tipping valve must
have a pressure relief at the cylinder port set not higher than max. working pressure. Verify max. cyl. load. Working temperature range is between
-40°C and +80°C. Max. duration of extension is 0.5 hours (excluded hard chromed stages). Cylinder is painted black (RAL9005) with a min.
thickness conforming to the 480 hours neutral salt spray test as per ISO 9227. ¹ Hyva knock-off.
Related documentation
Bracket options: 015BRA10 & 015BRA13 Mounting instructions: CYL-0031 Oil specifications: OIL-0011
Spec sheet explanation: CYL-0041
Tipping weight
BL body length BL [mm] 5000 4850 4700
OH rear overhang OH [mm] 200 400 600 200 400 600 200 400 600
Ycog vert. pos. centre At [°] 47 49 51 48 51 53 50 53 56
of gravity
Qo pivot length Ycog [mm]
C bracket length 400 63 68 74 64 69 76 65 71 79
At tipping angle 700 69 75 84 70 78 72
stroke x 60 / Qo 1000 76
Tipping weight [ton] at maximum pressure of 250 bar for a vertically mounted cylinder and C is 158 mm
For detailed tipping calculations please refer to: https://tipper.hyva.com
Subject to change without notice, no rights reserved Page 1/2 DO-E 70535210 / 2017-7-28 / RV AB
Alpha series - Front end cylinder with single eye
FE A149-3-03830-009-K1645-HD Item no. 70535210
Pos. Part no. Description Qty.
1
C01 71839120 DUST COVER FE 149-3 1
P01 74413551 PISTON FL2 S 110-1560-HD-HC 1
P02 71807112 K SLIDER FL 110 (2 X 1/2) A35 1
P03 71851110 K OUTER STOPRING FL 110 A22 2
P04 71822710 BOTTOM PLATE PISTON FL 110 MK2 HD 1
P05 01745021 K CIRCLIP 97 DIN 472 (102.5x3.0) 1
P06 71870220 K O-RING PISTON BOTTOM 110 1
P07 71847301 PISTON EYE SPH. FL 110 MK2 L=075 GR 1
P08 01226538 K O-RING 91.67 X 3.53 MM NBR 1
P09 01770085 K SPHERICAL BEARING D.50 DO GREASED 1
P10 01770560 K CIRCLIP 75 DIN 472 (79.5x3.0) 1
P11 71875012 PIN ROUND HEAD GROOVED 8x15 mm 2
P12 56288044 K GREASE NIPPLE M8x1 DIN 71412 1
P13 01317670 K GREASER PROTECTION CAP 1
S21 74614510 STAGE FL2 129-1510-HD 1
S22 71808129 K PACKSET FL 129/HP 129 TANDEM SEAL 1
S23 71807131 K SLIDER FL 129 (2 X 1/2) A35 1
S24 71851129 K OUTER STOPRING FL 129 A22 2
S25 71852129 K LIFTRING FL 129 A22 1
S11 74615510 STAGE FL2 149-1510-HD 1
S12 71808149 K PACKSET FL 149/HP 150 TANDEM SEAL 1
S13 71807151 K SLIDER FL 149 A35 1
S14 71851149 K OUTER STOPRING FL 149 A22 1
S15 71852149 K LIFTRING FL 149 A22 1
B01 74516510 BASE FL2 169-1549-4/4BSAE-190-HD 1
B02 71802169 K PACKSET FL 169 1
B03 71825425 BOTTOM PLATE FL2 169 1
B04 71870035 K SEAL BOTTOM PLATE FL 169 1
B05 71820169 LOCKING PLATE FL 169 3
B06 01732055 K BOLT HEX M8X20X1.25 SET 6 PCS 1
B07 01732559 K WASHER SPRING M8 SET 6 PCS 1
Seal kit complete Notes
71908531 K Consists of all packsets with packset grease and O- The inner stopring is pre-mounted in the grooves on spare bases and
rings stages.Therefore, when ordering new tubes, it is not required to order inner stoprings
separately.
For repair instructions see: CYL-0040. Serial no. is located on type plate and near type plate support.
Subject to change without notice, no rights reserved Page 2/2 DO-E 70535210 / 2017-7-28 / RV AB
