Data sheet 6ES7307-1EA01-0AA0

SIMATIC PS307/1AC/24VDC/5A

SIMATIC S7-300 Regulated power supply PS307 input: 120/230 V AC, output: 24
V/5 A DC

input
type of the power supply network 1-phase AC
supply voltage at AC Automatic range selection
supply voltage 120 V/230 V
input voltage 1 at AC 85 ... 132 V
input voltage 2 at AC 170 ... 264 V
wide range input No
overvoltage overload capability 2.3 × Vin rated, 1.3 ms
buffering time for rated value of the output current in the event of 20 ms
power failure minimum
operating condition of the mains buffering at Vin = 93/187 V
line frequency 50/60 Hz
line frequency 47 ... 63 Hz
input current
● at rated input voltage 120 V 2.3 A
● at rated input voltage 230 V 1.2 A
current limitation of inrush current at 25 °C maximum 20 A
duration of inrush current limiting at 25 °C
● maximum 3 ms
I2t value maximum 1.2 A²·s
fuse protection type T 3,15 A/250 V (not accessible)
fuse protection type in the feeder Recommended miniature circuit breaker: from 6 A characteristic C
output
voltage curve at output Controlled, isolated DC voltage
output voltage at DC rated value 24 V
output voltage
● at output 1 at DC rated value 24 V

output voltage adjustable No; -

relative overall tolerance of the voltage 3%
relative control precision of the output voltage
● on slow fluctuation of input voltage 0.1 %
● on slow fluctuation of ohm loading 0.5 %
residual ripple
● maximum 50 mV
● typical 10 mV
voltage peak
● maximum 150 mV
● typical 20 mV
display version for normal operation Green LED for 24 V OK
behavior of the output voltage when switching on No overshoot of Vout (soft start)

6ES73071EA010AA0 Subject to change without notice

6/23/2024
Page 1/4 © Copyright Siemens
 response delay maximum 2s
voltage increase time of the output voltage
● typical 10 ms
output current
● rated value 5A
● rated range 0 ... 5 A

supplied active power typical 120 W

short-term overload current
● on short-circuiting during the start-up typical 20 A
● at short-circuit during operation typical 20 A
duration of overloading capability for excess current
● on short-circuiting during the start-up 100 ms
● at short-circuit during operation 100 ms
bridging of equipment Yes
efficiency
efficiency in percent 87 %
power loss [W]
● at rated output voltage for rated value of the output 18 W
current typical
closed-loop control
relative control precision of the output voltage with rapid 0.1 %
fluctuation of the input voltage by +/- 15% typical
relative control precision of the output voltage load step of 1%
resistive load 50/100/50 % typical
setting time
● load step 50 to 100% typical 0.3 ms
● load step 100 to 50% typical 0.3 ms
protection and monitoring
design of the overvoltage protection Additional control loop, shutdown at < 28.8 V, automatic restart
property of the output short-circuit proof Yes
design of short-circuit protection Electronic shutdown, automatic restart
response value current limitation 5.5 ... 6.5 A
enduring short circuit current RMS value
● maximum 7A
safety
galvanic isolation between input and output Yes
galvanic isolation Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178
operating resource protection class Class I
leakage current
● maximum 3.5 mA
● typical 0.5 mA
protection class IP IP20
standard
● for emitted interference EN 55022 Class B
● for mains harmonics limitation EN 61000-3-2
● for interference immunity EN 61000-6-2
standards, specifications, approvals
certificate of suitability
● CE marking Yes
● UL approval Yes; cULus-Listed (UL 508, CSA C22.2 No. 142), File E143289
● CSA approval Yes; cULus-Listed (UL 508, CSA C22.2 No. 142), File E143289
● EAC approval Yes
● NEC Class 2 No
type of certification
● BIS Yes; R-41183539
● CB-certificate Yes
MTBF at 40 °C 2 480 589 h
standards, specifications, approvals hazardous environments
certificate of suitability
● IECEx Yes; IECEx Ex nA nC IIC T3 Gc
● ATEX Yes; ATEX (EX) II 3G Ex nA nC IIC T3 Gc

6ES73071EA010AA0 Subject to change without notice

6/23/2024
Page 2/4 © Copyright Siemens
 ● ULhazloc approval Yes
● cCSAus, Class 1, Division 2 No
● FM registration Yes; Class I, Div. 2, Group ABCD, T4
standards, specifications, approvals marine classification
shipbuilding approval Yes
Marine classification association
● American Bureau of Shipping Europe Ltd. (ABS) No
● French marine classification society (BV) No
● Det Norske Veritas (DNV) No
● Lloyds Register of Shipping (LRS) Yes
standards, specifications, approvals Environmental Product Declaration
Environmental Product Declaration Yes
Global Warming Potential [CO2 eq]
● total 575.4 kg
● during manufacturing 11.8 kg
● during operation 563.1 kg
● after end of life 0.38 kg
ambient conditions
ambient temperature
● during operation 0 ... 60 °C; with natural convection
● during transport -40 ... +85 °C
● during storage -40 ... +85 °C
environmental category according to IEC 60721 Climate class 3K3, 5 ... 95% no condensation
connection method
type of electrical connection screw terminal
● at input L, N, PE: 1 screw terminal each for 0.5 ... 2.5 mm² single-core/finely stranded
● at output L+, M: 3 screw terminals each for 0.5 ... 2.5 mm²
● for auxiliary contacts -
mechanical data
width × height × depth of the enclosure 60 × 125 × 120 mm
installation width × mounting height 60 mm × 205 mm
required spacing
● top 40 mm
● bottom 40 mm
● left 0 mm
● right 0 mm
fastening method Can be mounted onto S7 rail
● standard rail mounting No
● S7 rail mounting Yes
● wall mounting No
housing can be lined up Yes
net weight 0.6 kg
accessories
mechanical accessories Mounting adapter for standard mounting rail (6EP1971-1BA00)
further information internet links
internet link
● to website: Industry Mall https://mall.industry.siemens.com
additional information
other information Specifications at rated input voltage and ambient temperature +25 °C (unless
otherwise specified)
security information
security information Siemens provides products and solutions with industrial cybersecurity functions
that support the secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber
threats, it is necessary to implement – and continuously maintain – a holistic,
state-of-the-art industrial cybersecurity concept. Siemens’ products and
solutions constitute one element of such a concept. Customers are responsible
for preventing unauthorized access to their plants, systems, machines and
networks. Such systems, machines and components should only be connected
to an enterprise network or the internet if and to the extent such a connection is
necessary and only when appropriate security measures (e.g. firewalls and/or
network segmentation) are in place. For additional information on industrial
cybersecurity measures that may be implemented, please visit
www.siemens.com/cybersecurity-industry. Siemens’ products and solutions

6ES73071EA010AA0 Subject to change without notice

6/23/2024
Page 3/4 © Copyright Siemens
 undergo continuous development to make them more secure. Siemens strongly
recommends that product updates are applied as soon as they are available
and that the latest product versions are used. Use of product versions that are
no longer supported, and failure to apply the latest updates may increase
customer’s exposure to cyber threats. To stay informed about product updates,
subscribe to the Siemens Industrial Cybersecurity RSS Feed under
https://www.siemens.com/cert. (V4.7)
Classifications
Version Classification

eClass 14 27-04-07-01
eClass 12 27-04-07-01
eClass 9.1 27-04-07-01
eClass 9 27-04-07-01
eClass 8 27-04-90-02
eClass 7.1 27-04-90-02
eClass 6 27-04-90-02
ETIM 9 EC002540
ETIM 8 EC002540
ETIM 7 EC002540
IDEA 4 4130
UNSPSC 15 39-12-10-04

Approvals Certificates
General Product Approval

Manufacturer Declara-
tion

General Product Approval Marine / Shipping Environment

BIS CRS

last modified: 6/14/2024

6ES73071EA010AA0 Subject to change without notice

6/23/2024
Page 4/4 © Copyright Siemens