7/25/2019 Jhon Deere DTC.

pdf

Diagnostic Trouble Codes

Diagnostic Trouble Code Priorities

IMPORTANT: These Diagnostic Trouble

Codes are listed for reference only. See
your John Deere dealer for specific
diagnostic information.

Each Diagnostic Trouble Code (DTC) has a

priority. The priority of the DTC is indicated in
the way the DTC is displayed to the operator:

Priority 1 - The Cornerpost Display 1

will stop normal function and the DTC
will be displayed. This indicates a
problem that requires the combine be
stopped, the engine turned off
immediately and the problem corrected.
The Cornerpost Display 1 will show the
DTC until the problem is resolved.
Priority 2 - The Cornerpost Display 1
Diagnostic Indicator comes on. This
indicates a problem that should be
checked immediately
Priority 3 - DTC's will be stored, but it
is not indicated to the operator.

OUZXMAG,00018B6 -19-10OCT02-1/27

http://slidepdf.com/reader/full/jhon-deere-dtcpdf 1/27
7/25/2019 Jhon Deere DTC.pdf

OUZXMAG,00018B6 -19-10OCT02-2/27

http://slidepdf.com/reader/full/jhon-deere-dtcpdf 2/27
7/25/2019 Jhon Deere DTC.pdf

A-Diagnostics Menu E-Display and Clear H-HeaderTrak Angle J-Machine Setting

B-Diagnostic Trouble Diangostic Trouble Sensor Calibration Addresses - Up &
Code Controller List codes I-Deck Plate Position Down Arrow Button
C-Quick Cal Menu F-Concave Position Sensor Calibration to change address -
D-Diagnostic Address Sensor Calibration CAL Button to
List G-Header change digit - Enter
Calibration Button to set change
into memory

Accessing Diagnostic Trouble Codes Turn the key switch to the run position.

Prepare Combine:
OUZXMAG,00018B6 -19-10OCT02-3/27

Press the diagnostic switch. dIA will appear on

the Cornerpost Display 1.

OUZXMAG,00018B6 -19-10OCT02-4/27

Press the up or down arrow switch to obtain the

desired address. For example A00 appears on
the Cornerpost Display 1.

OUZXMAG,00018B6 -19-10OCT02-5/27

http://slidepdf.com/reader/full/jhon-deere-dtcpdf 3/27
7/25/2019 Jhon Deere DTC.pdf

Press the enter switch.

OUZXMAG,00018B6 -19-10OCT02-6/27

Press the up arrow switch once. If diagnostic

trouble codes are available A00 and codE will
appear on Cornerpost Display 1.

If no DTC is available A00 and nonE will

appear on Cornerpost Display 1.

OUZXMAG,00018B6 -19-10OCT02-7/27

To read and record diagnostic trouble codes

press the enter switch.

OUZXMAG,00018B6 -19-10OCT02-8/27

http://slidepdf.com/reader/full/jhon-deere-dtcpdf 4/27
7/25/2019 Jhon Deere DTC.pdf

Press the up or down arrow switch to scroll

through the diagnostic trouble codes.

Record each control unit name

Record each suspected parameter
number
Record each failure mode identifier

OUZXMAG,00018B6 -19-10OCT02-9/27

After all codes have been displayed, there is an

option to clear these codes.

Scroll to end of code list until CLr? is

displayed.

OUZXMAG,00018B6 -19-10OCT02-10/27

Press the enter

donE will switch
appear to clear codes.
on Cornerpost A001.and
Display

OUZXMAG,00018B6 -19-10OCT02-11/27

http://slidepdf.com/reader/full/jhon-deere-dtcpdf 5/27
7/25/2019 Jhon Deere DTC.pdf

NOTE: Priority 1 codes cannot be cleared until

the problem is solved.

Press back arrow switch three times to return to

normal operation.

OUZXMAG,00018B6 -19-10OCT02-12/27

A00 - Engine Control Unit Diagnostic

Trouble Codes

Control
Unit SPN FMI Pri. Description
A00 91 09 3 Throttle input not valid or not received
A00 94 01 1 Fuel pressure too low - less than 80kPa / 11.6 PSI (9540)
A00 94 03 1 Fuel Pressure Sensor (cc# 131) voltage out of range high - greater than
4 V DC (9640, 9560, 9660, 9580, 9680)
A00 94 04 1 Fuel Pressure Sensor (cc# 131) voltage out of range low. (9640, 9560,
9660, 9580, 9680)
A00 94 10 2 The rail pressure drops too fast when the engine is motoring and the
high pressure pump is off. (9640, 9560, 9660, 9580, 9680)
A00 94 13 1 Fuel Pressure Sensor reading is incorrect. (9640, 9560, 9660, 9580,
9680)
A00 94 17 2 During starting, rail pressure is not developed after a short time
cranking. (9640, 9560, 9660, 9580, 9680)
A00 94 18 2 Fuel pressure too low - less than 100 kPa / 14.7 PSI at low idle (9540)
A00 97 03 2 Water in Fuel Sensor (cc# 136) voltage out of range high (9640, 9560-
Engine Type B, 9660, 9580, 9680)
A00 97 04 2 Water in Fuel Sensor (cc# 136) voltage out of range low (9640, 9560-
Engine Type B, 9660, 9580, 9680)

A00 97 31 2 Water is detected in fuel. (9640, 9560-Engine Type B, 9660, 9580,

9680)
A00 100 01 1 Oil Pressure Sensor is open after engine rpm is above cranking speed
A00 100 04 2 Oil Pressure Sensor is closed when engine is not running (9640, 9560,
9660, 9580, 9680)
Engine Manifold Air Temperature Sensor is above 100°C (9560-
A00 105 00 1
Engine Type C only)

http://slidepdf.com/reader/full/jhon-deere-dtcpdf 6/27
7/25/2019 Jhon Deere DTC.pdf

A00 105 03 2 Engine Manifold Air Temperature Sensor voltage is out of range high.
The device or wiring is faulty. (9640, 9560, 9660, 9580, 9680)
A00 105 04 2 Engine Manifold Air Temperature Sensor voltage is out of range low.
The device or wiring is faulty. (9640, 9560, 9660, 9580, 9680)
A00 105 16 2 Engine Manifold Air temperature above 88°C / 190°F (moderately
severe level). Maximum power level is derated. Power boost is
disabled.
A00 107 00 2 Air Filter Restricted Switch indicates a plugged air filter.
A00 110 00 1 Engine coolant temperature above 115°C / 240°F (most severe level).
Maximum power level is derated. Power boost is disabled.
A00 110 03 2 Engine Coolant Temperature Sensor voltage is out of range high. The
device or wiring is faulty.
A00 110 04 2 Engine Coolant Temperature Sensor voltage is out of range low. The
device or wiring is faulty.
A00 110 15 2 Engine Coolant Temperature is above 105°C. (9560-Engine Type C)
A00 110 16 2 Engine coolant temperature above 110°C / 230°F for 9640, 9560, 9660,
9580 and 9680 or above 100°C / 212°F for 9540. Maximum power
level is derated. Power boost is disabled.
A00 111 01 1 Coolant level low. Engine coolant temperature above 125°C / 257°F.
Maximum power level is derated. Power boost is disabled.
A00 158 17 2 Controller not powered down properly. (9640, 9560, 9660, 9580, 9680)
Engine fuel temperature is too high (greater than 75°C / 167°F).
A00 174 00 2 Injector pump may be damaged because hot fuel loses its lubrication
properties. (9540)
A00 174 03 2 Engine Fuel Temperature Sensor voltage is out of range high. The
device or wiring is faulty. Injector pump may be damaged because hot
fuel loses its lubrication properties. (9640, 9560, 9660, 9580, 9680)

OUZXMAG,00018B6 -19-10OCT02-13/27

Control
SPN FMI Pri. Description
Unit
A00 174 04 2 Engine Fuel Temperature Sensor voltage is out of range low. The
device or wiring is faulty. Injector pump may be damaged because hot
fuel loses its lubrication properties. (9640, 9560, 9660, 9580, 9680)
Engine fuel temperature above normal range (greater than 65°C /
A00 174 15 2
149°F). Maximum power level and power boost are derated. (9540)

http://slidepdf.com/reader/full/jhon-deere-dtcpdf 7/27
7/25/2019 Jhon Deere DTC.pdf

Engine fuel temperature above normal range (greater than 65°C /

A00 174 16 2 149°F for 9640, 9560, 9660, 9580, 9680 or greater than 73°C / 163°F
for 9540). Maximum power level and power boost are derated.
Engine Fuel Temperature Sensor is out of range. Maximum power
A00 174 31 2
level and power boost are derated. (9540)
A00 189 00 3 Low fuel pressure (9540)
A00 190 00 1 Engine over-speed (greater than 2800 rpm). (9540)
Engine speed too high (greater than 2800 rpm). Engine Control Unit
A00 190 16 3
reduce fuel flow until speed is below 2200 rpm (9540)
A00 611 03 1 The injector driver has detected a short to battery in the injector wiring.
(9640, 9560, 9660, 9580, 9680)
A00 611 04 1 The injector driver has detected a short to ground in the injector wiring.
(9640, 9560, 9660, 9580, 9680)
A00 627 01 2 All injector currents are out of specification. The injector pull-in
current is too low or the injector hold-in current is incorrect. (9640,
9560, 9660, 9580, 9680)
Engine Control Unit Power (cc# 042) missing at Engine Control Unit
A00 627 04 2
while Electronic Power (cc# 021) is on. (9540)
A00 629 19 2 Engine Control Unit not receiving messages from Pump. (9540)
A00 632 02 2 Fuel shutoff error condition detected. (9540)
The Engine Control Unit does not detect a change in engine speed after
A00 632 05 2 the Key Switch is turned off. Fuel shutoff not functioning correctly.
(9540)

A00 636 02 2 Electrical noise detected

Pump Position Sensor - on Pump
(cc# 173)Position Sensor + (cc# 172) and/or
A00 636 08 2 Pump Position Sensor signal is missing
A00 636 10 2 Pump Position Sensor signal has incorrect pulse pattern
A00 637 02 2 Electrical noise detected on Pump Position Sensor + (cc# 174) and/or
Pump Position Sensor - (cc# 175)
A00 637 07 2 Position relationship between Engine Speed Sensor and Pump Position
Sensor not correct (9640, 9560, 9660, 9580, 9680)
A00 637 08 2 Engine Speed Sensor signal is missing
A00 637 10 2 Engine Speed Sensor signal has incorrect pulse pattern
A00 651 05 2 The current to Injector #1 is less than expected. (9640, 9560, 9660,
9580, 9680)
A00 651 06 2 The current to Injector #1 increases too rapidly. (9640, 9560, 9660,
9580, 9680)
A00 651 07 2 The fuel flow to cylinder #1 is lower than expected. (9640, 9560-
Engine Type B, 9660, 9580)

http://slidepdf.com/reader/full/jhon-deere-dtcpdf 8/27
7/25/2019 Jhon Deere DTC.pdf

A00 652 05 2 The current to Injector #2 is less than expected. (9640, 9560, 9660,
9580, 9680)
A00 652 06 2 The current to Injector #2 increases too rapidly. (9640, 9560, 9660,
9580, 9680)
A00 652 07 2 The fuel flow to cylinder #2 is lower than expected. (9640, 9560-
Engine Type B, 9660, 9580, 9680)

OUZXMAG,00018B6 -19-10OCT02-14/27

Control
SPN FMI Pri. Description
Unit
A00 653 05 2 The current to Injector #3 is less than expected. (9640, 9560, 9660,
9580, 9680)
A00 653 06 2 The current to Injector #3 increases too rapidly. (9640, 9560, 9660,
9580, 9680)
A00 653 07 2 The fuel flow to cylinder #3 is lower than expected. (9640, 9560-
Engine Type B, 9660, 9580, 9680)
A00 654 05 2 The current to Injector #4 is less than expected. (9640, 9560, 9660,
9580, 9680)
A00 654 06 2 The current to Injector #4 increases too rapidly. (9640, 9560, 9660,
9580, 9680)
A00 654 07 2 The fuel flow to cylinder #4 is lower than expected. (9640, 9560-
Engine Type B, 9660, 9580, 9680)
A00 655 05 2 The current to Injector #5 is less than expected. (9640, 9560, 9660,
9580, 9680)
A00 655 06 2 The current to Injector #5 increases too rapidly. (9640, 9560, 9660,
9580, 9680)
A00 655 07 2 The fuel flow to cylinder #5 is lower than expected. (9640, 9560-
Engine Type B, 9660, 9580, 9680)
A00 656 05 2 The current to Injector #6 is less than expected. (9640, 9560, 9660,
9580, 9680)
A00 656 06 2 The current to Injector #6 increases too rapidly. (9640, 9560, 9660,
9580, 9680)
A00 656 07 2 The fuel flow to cylinder #6 is lower than expected. (9640, 9560-
Engine Type B, 9660, 9580)
A00 676 03 2 The Glow Plug Relay output is on when the relay is not energized by

http://slidepdf.com/reader/full/jhon-deere-dtcpdf 9/27
7/25/2019 Jhon Deere DTC.pdf

the Engine Control Unit. (9560-Engine Type C)

The Glow Plug Relay output is off when the relay is energized by the
A00 676 05 2
Engine Control Unit. (9560-Engine Type C)
Inlet Air Heater Relay Output (cc# 189) is high when Engine Control
A00 729 03 2
Unit is not energizing the Glow Plug Relay. (9540)
Inlet Air Heater Relay Output (cc# 189) is low when Engine Control
A00 729 05 2
Unit is energizing the Inlet Air Heater Relay. (9540)
The High Pressure Solenoid within the pump is continuously
energized, the Pump Control Unit is unable to detect closure of the
A00 1076 02 2
High Pressure Solenoid Valve or the internal pump speed sensor is
broken. (9540)
The High Pressure Solenoid Valve is closed when the Engine Control
A00 1077 07 2 Unit is commanding the Pump Control Unit to stop delivering fuel.
(9540)

A00 1077 11 2 The Pump Control Unit senses an abnormal voltage on Pump Power
(cc# 061). (9540)
A00 1077 12 2 The Pump Control Unit detects an error during a self test. (9540)
The Pump Control Unit is not receiving any ECU/CAN messages
A00 1077 19 2
while detecting a signal on Crank Speed Out (cc# 187). (9540)
Injection Pump initiated engine protection due to Diagnostic Trouble
A00 1077 31 1 Code 174.31, 1076.02, 1077.12, 1078.07 or 1078.31. Engine will
derate. (9540)
The Pump Control Unit receives a crank signal from the Engine
A00 1078 07 2 Control Unit that is moderately different than the internal timing within
the Pump. Engine will be derated. (9540)
The Engine Control Unit detects a difference between the internal
A00 1078 11 2
pump timing and engine speed. (9540)
The Pump Control Unit receives a crank signal from the Engine
A00 1078 31 2 Control Unit that is extremely different than the internal timing within
the Pump. Engine will be derated. (9540)
Sensor Supply Voltage 1 (cc# 131) too high (greater than 4.95 V DC).
A00 1079 03 2
(9540)
Sensor Supply Voltage 1 (cc# 131) too low (less than 4.0 V DC).
A00 1079 04 3
(9540)
A00 1080 03 1 Rail Pressure Sensor Power (cc# 721) voltage too high. (9640, 9560,
9660, 9580, 9680)

OUZXMAG,00018B6 -19-10OCT02-15/27

http://slidepdf.com/reader/full/jhon-deere-dtcpdf 10/27
7/25/2019 Jhon Deere DTC.pdf

Control
SPN FMI Pri. Description
Unit
A00 1080 04 1 Rail Pressure Sensor Power (cc# 721) voltage too low. (9640, 9560,
9660, 9580, 9680)
A00 1080 04 3 Rail Pressure Sensor Power (cc# 721) voltage too low. (9540)
A00 1347 03 1 CC# 178 Shorted to power. (9560-Engine Type C)
A00 1347 05 2 Driver detects problem in circuit to Pump Solenoid 1 Low (cc# 178).
(9640, 9560, 9660, 9580, 9680)
A00 1347 07 2 Rail Pressure Control is unable to match required rail pressure. It may
bee too high or too low. (9640, 9560, 9660, 9580, 9680)
A00 1347 10 2 Pump Solenoid 1 is not delivering expected fuel flow. (9640, 9560-
Engine Type B, 9660, 9580, 9680)

A00 1348 05 2 Driver detects problem in circuit to Pump Solenoid 2 Low (cc# 179).
(9640, 9560-Engine Type B, 9660, 9580, 9680)
A00 1348 10 2 Pump Solenoid 2 is not delivering expected fuel flow. (9640, 9560-
Engine Type B, 9660, 9580, 9680)
Pump Power (cc# 061) is powered when Engine Control Unit is off.
A00 1485 02 2
(9540)
A00 1569 31 2 Engine protection - power derated due to other faults. This code occurs
in conjunction with 105.16, 110.00, 110.03, 110.04, and 110.16. (9640,
9560, 9660, 9580, 9680)
A00 2000 13 1 Engine Control Unit security violation.

OUZXMAG,00018B6 -19-10OCT02-16/27

C00 - Armrest Control Unit Diagnostic

Trouble Codes

Control
Unit SPN FMI Pri. Description
C00 158 04 3 Control Circuit Power (cc# 023) is below 10.5 V DC.
C00 170 03 3 CLIMATRAK Cab Air Temperature Sensor voltage too high - greater
than 4.8 V DC. Indicates that the sensor resistance is greater than
60KΩ ( -22°F or -30°C).
C00 170 04 3 CLIMATRAK Cab Air Temperature Sensor voltage too low - less than
0.1 V DC. Indicates that the sensor resistance is less than 50Ω (293°F

http://slidepdf.com/reader/full/jhon-deere-dtcpdf 11/27
7/25/2019 Jhon Deere DTC.pdf

or 145°C).
C00 172 03 3 CLIMATRAK Outside Air Temperature Sensor voltage too high -
greater than 4.8 V DC. Indicates that the sensor resistance is greater
than 60KΩ ( -22°F or -30°C).
C00 172 04 3 CLIMATRAK Outside Air Temperature Sensor voltage too low - less
than 0.1 V DC. Indicates that the sensor resistance is less than 50Ω
(293°F or 145°C).
C00 190 09 3 CAN Bus message missing from Engine Control Unit - Engine Speed
C00 605 04 3 CLIMATRAK Lo Pressure Switch (cc#914) is 12 V DC. A CAN Bus
message from the Left Control Unit indicates that the CLIMATRAK
Hi Pressure Switch (cc#915) is 0 V DC. The CLIMATRAK Hi
Pressure Switch is open or there is a harness problem.
C00 627 03 1 Delayed Power (cc# 006) voltage is above 16 V DC. High voltage
situation must be resolved.

C00 627 04 3 Delayed Power (cc# 006) is below 10.5 V DC.

C00 628 12 1 Controller cannot exit boot block program. Disconnect Armrest
Control Unit connectors X653 and X654. Reconnect connectors.
Replace Armrest Control Unit if condition persists.
C00 630 11 1 Controller failed EEPROM test at power-up. Replace Armrest Control
Unit if condition persists.
C00 639 19 3 CAN Bus messages are not being transmitted or received correctly.
Possible effects are none, slow response, or machine down.
C00 875 04 3 CAN Bus message from Left Control Unit indicates that
CLIMATRAK Clutch Signal (cc# 913) is 12 V DC. CLIMATRAK Lo
Pressure Switch (cc# 914) is 0 V DC. The CLIMATRAK Lo Pressure
Switch is open or there is a harness problem.
C00 1490 08 2 Backshaft speed unknown. Damage could occur to feeder house if
reverser is engaged while backshaft is rotating in forward direction.
C00 1498 11 3 The header engage output transistor detects an open, short, over
voltage, or over temperature condition. The Armrest Control Unit will
disengage the header. The fault condition must be removed before the
header can be engaged.
C00 1499 11 3 The separator engage output transistor detects an open, short, over
voltage, or over temperature condition. The Armrest Control Unit will
disengage the separator. The fault condition must be removed before
the separator can be engaged.
C00 1499 12 2 The Separator Engage fault detection circuit indicates a failure. This is
an important disengagement override system. Replace the Armrest
Control Unit if condition persists.
C00 1504 11 1 The Seat Switch has been closed continuously for 6 hours. The switch
or the wiring harness is shorted. The header will not disengage when

http://slidepdf.com/reader/full/jhon-deere-dtcpdf 12/27
7/25/2019 Jhon Deere DTC.pdf

the operator has left the seat. This must be corrected.

C00 1505 03 3 HEADERTRAK Sensitivity Adjust voltage is too high - greater than
4.5 V DC. The device or wiring is faulty.
C00 1505 04 3 HEADERTRAK Sensitivity Adjust voltage is too low - less than 0.5 V
DC. The device or wiring is faulty.
C00 1506 03 3 HEADERTRAK Rate Adjust voltage is too high - greater than 4.5 V
DC. The device or wiring is faulty.

OUZXMAG,00018B6 -19-10OCT02-17/27

Control
Unit SPN FMI Pri. Description

C00 1506 04 3 HEADERTRAK Rate Adjust voltage is too low - less than 0.5 V
DC. The device or wiring is faulty.
C00 1505 10 3 HEADERTRAK Rate Adjust calibration fault: The potentiometer
was calibrated in the wrong direction or the difference between the
two calibration endpoints is less than 2.00 volts. This diagnostic
trouble code is only displayed during a calibration fault and is not
stored.
C00 1547 03 3 CLIMATRAK Core Temperature Sensor voltage too high - greater

than
101KΩ4.47 V DC.
( -4°F or Indicates
-20°C). that the sensor resistance is greater than
C00 1547 04 3 CLIMATRAK Core Temperature Sensor voltage too low - less than
0.1 V DC. Indicates that the sensor resistance is less than 52Ω
(356°F or 180°C).
C00 1548 03 3 CLIMATRAK Outlet Air Temperature Sensor voltage too high -
greater than 4.8 V DC. Indicates that the sensor resistance is greater
than 60KΩ ( -22°F or -30°C).
C00 1548 04 3 CLIMATRAK Outlet Air Temperature Sensor voltage too low - less
than 0.1 V DC. Indicates that the sensor resistance is less than 50Ω
(293°F or 145°C).
C00 1549 07 3 CLIMATRAK Water Valve position is greater than 30% different
than the commanded position.
C00 200011 03 3 CLIMATRAK Solar Sensor voltage is too high - greater than 4.8 V
DC. The device or wiring is faulty.
C00 200011 04 3 CLIMATRAK Solar Sensor voltage is too low - less than 1.5 V DC.
The device or wiring is faulty.

http://slidepdf.com/reader/full/jhon-deere-dtcpdf 13/27
7/25/2019 Jhon Deere DTC.pdf

C00 200017 09 3 CAN Bus message(s) missing from Cornerpost Control Unit.
C00 200018 09 3 CAN Bus message(s) missing from Left Control Unit.
C00 200201 11 3 Separator Engage Switch inputs are incorrect.
C00 200202 11 3 Header Engage Switch inputs are incorrect.

OUZXMAG,00018B6 -19-10OCT02-18/27

C03 - Cornerpost Control Unit Diagnostic

Trouble Codes

Control
SPN FMI Pri. Description
Unit
C03 96 09 3 CAN Bus message missing from Right Control Unit - Fuel Level.
C03 110 09 3 CAN Bus message missing from Engine Control Unit - Engine Coolant
Temperature
C03 190 09 3 CAN Bus message missing from Engine Control Unit - Engine Speed
C03 627 03 3 Delayed Power (cc# 006) voltage out of range high - greater than 16 V
DC.
C03 628 12 1 Controller cannot exit boot block program. Disconnect Cornerpost
Control Unit connector X500. Reconnect connector. Replace
Cornerpost Control Unit if condition persists.
C03 630 11 1 EEPROM failed test at power up. Replace Cornerpost Control Unit if
condition persists.
C03 639 19 3 CAN Bus messages are not being transmitted or received correctly.
Possible effects are none, slow response, or machine down.
C03 1079 03 3 Concave Position Sensor supply voltage high - greater than 5.5 V DC.
C03 1079 04 3 Concave Position Sensor supply voltage low - less than 4.5 V DC.
C03 1486 03 3 Concave Position Sensor voltage is too high - greater than 4.5 V DC.
The device or wiring is faulty.
C03 1486 04 3 Concave Position Sensor voltage is too low - less than 0.5 V DC. The
device or wiring is faulty.
C03 1487 03 3 Dimmer voltage is too high - greater than 4.5 V DC. The device or
wiring is faulty.
C03 1487 04 3 Dimmer voltage is too low - less than 0.5 V DC. The device or wiring
is faulty.
C03 1492 08 3 Cab interior backlighting output transistor detects an open, short, over
voltage, or over temperature condition. The Cornerpost Control Unit

http://slidepdf.com/reader/full/jhon-deere-dtcpdf 14/27
7/25/2019 Jhon Deere DTC.pdf

will turn off the backlighting. The fault condition must be removed
before the backlighting can be turned on.
C03 1493 09 3 CAN Bus message missing from Master Tailings Sensor - Tailings
Volume
C03 1500 11 3 A switch on Cornerpost Display Unit 1 is closed for longer than 30
Seconds.
C03 1501 11 3 A switch on Cornerpost Display Unit 2 is closed for longer than 30
Seconds.
C03 1502 11 3 A switch on Cornerpost Display Unit 3 is closed for longer than 30
Seconds.
C03 1503 09 3 CAN Bus message missing from Armrest Control Unit - Armrest
Switch Status
C03 1510 09 3 CAN Bus message missing from Right Control Unit - Combine
Temperatures
C03 1511 09 3 CAN Bus message missing from Right Control Unit - Grain Loss
C03 1515 09 3 CAN Bus message missing from Header Control Unit - Header Data
C03 1552 03 3 CLIMATRAK Temperature Setpoint Adjust voltage too high - greater
than 4.5 V DC. Device or wiring is faulty.
C03 1552 04 3 CLIMATRAK Temperature Setpoint Adjust voltage too low - less than
0.5 V DC. Device or wiring is faulty.
CLIMATRAK Temperature Setpoint Adjust not calibrated. Refer to
C03 1552 13 3
Diagnostic Address C03-135 for calibration.
C03 1553 03 3 CLIMATRAK Fan Speed Adjust voltage too high - greater than 4.5 V

DC. Device or wiring is faulty.

C03 1553 04 3 CLIMATRAK Fan Speed Adjust voltage too low - less than 0.5 V DC.
Device or wiring is faulty.
CLIMATRAK Fan Speed Adjust not calibrated. Refer to Diagnostic
C03 1553 13 3
Address C03-134 for calibration.
C03 1565 09 3 CAN Bus message missing from Armrest Control Unit - Separator and
Header Engage Status

OUZXMAG,00018B6 -19-10OCT02-19/27

Control
SPN FMI Pri. Description
Unit
C03 1567 09 3 CAN Bus message missing from Header Control Unit - Control

http://slidepdf.com/reader/full/jhon-deere-dtcpdf 15/27
7/25/2019 Jhon Deere DTC.pdf

Mode
C03 100100 09 3 CAN Bus message missing from Left Control Unit - System Data
C03 100101 09 3 CAN Bus message missing from Left Control Unit 2 - System Data
C03 100106 11 3 A switch on Cornerpost Display Unit 4 is closed for longer than 30
Seconds.

E00 - Tailings Control Unit Diagnostic

Trouble Codes

Control
SPN FMI Pri. Description
Unit
E00 190 09 3 CAN Bus message missing from Engine Control Unit - Engine Speed

E00 628 12 2 Controller cannot exit boot block program. Turn Key Switch to the
OFF position. Wait 30 seconds. Replace Master Tailings Sensor if
condition persists.
E00 630 11 2 EEPROM failed test at power up. Replace the Master Tailings Sensor
if condition persists.
E00 639 09 3 CAN Bus messages are not received by the Tailings Control Unit in a
timely manner. Possible effects are none, slow response, or machine
down. Other Diagnostic Trouble Codes will indicate the lost message.
E00 639 19 3 CAN Bus messages are not being transmitted or received correctly.
Possible effects are none, slow response, or machine down.
E00 1493 11 3 Tailings system failure. Cause unknown.
E00 1493 15 3 Tailings system calibration is out of range high (sensor detectors are
receiving too little light). Recalibrate. If situation persists, possible
dirty sensor or failed sensor.
E00 1493 17 3 Tailings system calibration is out of range low (sensor detectors are
receiving too much light). Recalibrate. If situation persists, possible
missing elevator paddle or failed sensor.
E00 1494 08 3 Stuck photo receiver detected in Master Tailings Sensor. Clean master
tailings sensor. If condition persists, replace sensor.
E00 1494 11 3 Master Tailings Sensor failure. Cause unknown.
E00 1495 08 3 Stuck photo receiver detected in Slave Tailings Sensor. Clean Slave
Tailings Sensor. If condition continues, replace sensor.
E00 1495 11 3 Slave Tailings Sensor failure. Cause unknown.
E00 1496 07 3 Tailings elevator paddle missing
E00 1511 09 3 CAN Bus message missing from Right Control Unit - Seed Size
E00 1565 09 3 CAN Bus message missing from Armrest Control Unit - Header and

http://slidepdf.com/reader/full/jhon-deere-dtcpdf 16/27
7/25/2019 Jhon Deere DTC.pdf

Separator Engaged

OUZXMAG,00018B6 -19-10OCT02-20/27

E01 - Header Control Unit Diagnostic

Trouble Codes

Control
SPN FMI Pri. Description
Unit
E01 84 09 3 CAN Bus message missing from Cornerpost Control Unit - Wheel
Speed
E01 190 09 3 CAN Bus message missing from Engine Control Unit - Engine Speed
E01 627 03 1 Controller Supply voltage out of range high - greater than 16 V DC.
E01 628 12 1 Controller cannot exit boot block program. Disconnect Header Control
Unit connector X205. Reconnect connector. Replace Header Control
Unit if condition persists.
E01 630 11 3 System not calibrated or EEPROM failed test at power up. Calibrate
header. Replace the Header Control Unit if condition persists.
E01 639 13 3 Multiple CAN Bus messages have not been received by the Header
Control Unit in a timely manner. Possible effects are no effect, slowed
response, or no response.

E01 1079 03 2 Height Sensor Power (cc# 481) voltage is too high - greater than 5.25
V DC. Height Sensor Power is used to power the Return To Cut
Sensor, Reel Fore/Aft Position Sensor, Deck Plate Position Sensor,
Right HEADERTRAK Sensor, Center HEADERTRAK Sensor and
Left HEADERTRAK Sensor. The voltage regulator of the Header
Control Unit is bad or there is a short in the wiring.
E01 1079 04 2 Height Sensor Power (cc# 481) voltage is too low - less than 4.75 V
DC. Height Sensor Power is used to power the Return To Cut Sensor,
Reel Fore/Aft Position Sensor, Deck Plate Position Sensor, Right
HEADERTRAK Sensor, Center HEADERTRAK Sensor and Left
HEADERTRAK Sensor. The voltage regulator of the Header Control
Unit is bad or there is a short in the wiring.
E01 1080 03 2 Height Sensor Power 2 (cc# 471) voltage is too high - greater than 5.25
V DC. Height Sensor Power 2 is used to power the HEADERTRAK
Angle Sensor and the Header Raise Pressure Sensor. The voltage
regulator of the Header Control Unit is bad or there is a short in the
wiring.
E01 1080 04 2 Height Sensor Power 2 (cc# 471) voltage is too low - less than 4.75 V

http://slidepdf.com/reader/full/jhon-deere-dtcpdf 17/27
7/25/2019 Jhon Deere DTC.pdf

DC. Height Sensor Power 2 is used to power the HEADERTRAK

Angle Sensor and the Header Raise Pressure Sensor. The voltage
regulator of the Header Control Unit is bad or there is a short in the
wiring.
E01 1515 13 2 HEADERTRAK system not calibrated for currently attached header.
Perform the calibration procedure.
E01 1516 13 2 HEADERTRAK - Ground Pressure system not calibrated for currently
attached header. Perform the calibration procedure.
E01 1517 04 2 Header Raise Pressure (cc# 706) voltage is too low - less than 0.25 V
DC.
E01 1518 02 3 Circuit codes 436, 487, 488, and 489 changed while the
HEADERTRAK was in the automatic mode. These are the header
select lines that identify the type of header on the combine.
E01 1518 07 3 Header not connected or invalid connection. Circuit codes 436, 487,
488, and 489 are the header select lines that identify the type of header
on the combine.
E01 1518 14 3 Cannot activate HEADERTRAK Stubble Height or HEADERTRAK
Tilt Header sensors are not available.
E01 1519 11 2 Header raise valve driver detects an open, short, over voltage, or over
temperature condition. The Header Control Unit will not actuate the
Header Raise Valve until the fault condition is removed.
E01 1520 11 2 Header lower valve driver detects an open, short, over voltage, or over
temperature condition. The Header Control Unit will not actuate the
Header Lower Valve until the fault condition is removed.

E01 1521 11 2 Tilt left valve condition.

temperature driver detects
Thean open, Control
Header short, over
Unitvoltage,
will notoractuate
over the
HEADERTRAK Tilt Left Valve until the fault condition is removed.

OUZXMAG,00018B6 -19-10OCT02-21/27

Control
Unit SPN FMI Pri. Description
E01 1522 11 2 Tilt right valve driver detects an open, short, over voltage, or over
temperature condition. The Header Control Unit will not actuate the
HEADERTRAK Tilt Right Valve until the fault condition is removed.
E01 1524 11 3 Reel forward valve driver detects an open, short, over voltage, or over
temperature condition. The Header Control Unit will not actuate the
Reel Forward Valve until the fault condition is removed.

http://slidepdf.com/reader/full/jhon-deere-dtcpdf 18/27
7/25/2019 Jhon Deere DTC.pdf

E01 1525 11 3 Reel Aft valve driver detects an open, short, over voltage, or over
temperature condition. The Header Control Unit will not actuate the
Reel Aft Valve until the fault condition is removed.
E01 1526 11 3 Reel Raise valve driver detects an open, short, over voltage, or over
temperature condition. The Header Control Unit will not actuate the
Reel Raise Valve until the fault condition is removed.
E01 1527 11 3 Reel Lower valve driver detects an open, short, over voltage, or over
temperature condition. The Header Control Unit will not actuate the
Reel Lower Valve until the fault condition is removed.
E01 1528 11 3 Drop Rate valve driver detects an open, short, over voltage, or over
temperature condition. The Header Control Unit will not actuate the
Drop Rate Valve until the fault condition is removed.
E01 1529 11 3 Accumulator Shutoff valve driver detects an open, short, over voltage,
or over temperature condition. The Header Control Unit will not
actuate the Accumulator Shutoff Valve until the fault condition is
removed.
E01 1531 06 2 Reel Speed Increase driver detects an open, short, over voltage, or over
temperature condition. The Header Control Unit will not actuate the
Reel Speed Actuator in the increase speed mode until the fault
condition is removed
E01 1532 06 2 Reel Speed Decrease driver detects an open, short, over voltage, or
over temperature condition. The Header Control Unit will not actuate
the Reel Speed Actuator in the decrease speed mode until the fault
condition is removed
E01 1533 03 2 HEADERTRAK - Return to Cut Sensor (cc# 828) voltage is too high -
greater than 4.5 V DC. Faulty device or wiring.
E01 1533 04 2 HEADERTRAK - Return to Cut Sensor (cc# 828) voltage is too low -
less than 0.5 V DC. Faulty device or wiring.
E01 1534 03 2 Left HEADERTRAK Sensor (cc# 412) voltage is too high - greater
than 4.5 V DC. Faulty device or wiring.
E01 1534 04 2 Left HEADERTRAK Sensor (cc# 412) voltage is too low less than 0.5
V DC. Faulty device or wiring.
E01 1535 03 2 Right HEADERTRAK Sensor (cc# 454) voltage is too high - greater
than 4.5 V DC. Faulty device or wiring.

E01 1535 04 2 Right

0.5 VHEADERTRAK Sensor
DC. Faulty device (cc# 454) voltage is too low - less than
or wiring.
E01 1536 03 2 Center HEADERTRAK Sensor (cc# 414) voltage is too high - greater
than 4.5 V DC. Faulty device or wiring.
E01 1536 04 2 Center HEADERTRAK Sensor (cc# 414) voltage is too low - less than
0.5 V DC. Faulty device or wiring.
E01 1537 03 3 Reel Fore/Aft Position Sensor or Deck Plate Position Sensor (cc# 834)

http://slidepdf.com/reader/full/jhon-deere-dtcpdf 19/27
7/25/2019 Jhon Deere DTC.pdf

voltage too high - greater than 4.5 V DC. Faulty device or wiring.
E01 1537 04 3 Reel Fore/Aft Position Sensor or Deck Plate Position Sensor (cc# 834)
voltage too low - less than 0.5 V DC. Faulty device or wiring.
E01 1538 03 3 Reel Height Sensor (cc# 835) voltage too high - greater than 4.5 V DC.
Faulty device or wiring.
E01 1538 04 3 Reel Height Sensor (cc# 835) voltage too low - less than 0.5 V DC.
Faulty device or wiring.

OUZXMAG,00018B6 -19-10OCT02-22/27

Control
Unit SPN FMI Pri. Description

E01 1539 03 3 HEADERTRAK Angle Sensor (cc# 833) voltage too high - greater
than 4.5 V DC. Faulty device or wiring.
E01 1539 04 3 HEADERTRAK Angle Sensor (cc# 833) voltage too low - less than
0.5 V DC. Faulty device or wiring.
E01 1541 02 2 Reel speed unknown.
E01 1544 09 3 CAN Bus message missing from Armrest Control Unit - Multifunction
Lever Switch Status

E02 - Right Control Unit Diagnostic Trouble

Codes

Control
SPN FMI Pri. Description
Unit
E02 96 03 3 Fuel Level Signal (cc# 652) voltage is too high - greater than 1.96 V
DC. The device or wiring is faulty.
E02 96 04 3 Fuel Level Signal (cc# 652) voltage is too low - less than 0.12 V DC.
The device or wiring is faulty.
E02 627 03 1 Electronic Power (cc# 021) voltage is too high - greater than 16 V DC.
E02 628 12 1 Controller cannot exit boot block program. Turn Key Switch to the
OFF position. Wait for 30 seconds. Replace Right Control Unit if
condition persists.
E02 630 11 2 EEPROM failed test on power up. Replace the Right Control Unit if
condition persists.

http://slidepdf.com/reader/full/jhon-deere-dtcpdf 20/27
7/25/2019 Jhon Deere DTC.pdf

E02 639 09 3 CAN Bus messages are not received by the Right Control Unit in a
timely manner. Possible effects are none, slow response, or machine
down. Other Diagnostic Trouble Codes will indicate the lost message
E02 639 19 2 CAN Bus messages are not being transmitted or received correctly.
Possible effects are none, slow response, or machine down.
E02 1498 09 3 CAN Bus message missing from Armrest Control Unit - Header
Engage Status
E02 1500 09 3 CAN Bus message missing from Cornerpost Control Unit - Machine
Configuration
E02 1500 11 3 CAN Bus message from Cornerpost Control Unit invalid - Machine
Configuration
E02 1508 03 2 Hydraulic Oil Temperature Sensor (cc# 775) voltage is too high -
greater than 4.97 V DC. The device or wiring is faulty.
E02 1508 04 2 Hydraulic Oil Temperature Sensor (cc# 775) voltage is too low - less
than 0.29 V DC. The device or wiring is faulty.
E02 1509 03 2 Main Gearcase Oil Temperature Sensor (cc# 774) voltage is too high -
greater than 4.97 V DC. The device or wiring is faulty.
E02 1509 04 2 Main Gearcase Oil Temperature Sensor (cc# 774) voltage is too low -
less than 0.29 V DC. The device or wiring is faulty.
E02 1510 03 3 Chopper Vane Angle Sensor (cc# 781) voltage is too high (above 4.97
V DC). The device or wiring is faulty.
E02 1510 13 3 Chopper Vane Angle Sensor out of calibration. Perform the calibration
procedure.
E02 1565 09 3 CAN Bus message missing from Armrest Control Unit - Discrete Input
Status

OUZXMAG,00018B6 -19-10OCT02-23/27

E03 - Left Control Unit Diagnostic Trouble

Codes

Control SPN FMI Pri. Description

Unit
E03 190 09 3 CAN Bus message(s) missing from Engine Control Unit - Engine
Speed
E03 627 03 1 Electronic Power (cc# 021) voltage is too high - greater than 15.5 V
DC.
E03 628 12 1 Controller cannot exit boot block program. Disconnect Left Control

http://slidepdf.com/reader/full/jhon-deere-dtcpdf 21/27
7/25/2019 Jhon Deere DTC.pdf

Unit connector X213. Reconnect connector. Replace Left Control

Unit if condition persists.
E03 630 11 3 EEPROM failed test on power up. Replace the Left Control Unit if
condition persists.
E03 639 19 3 CAN Bus messages are not being transmitted or received correctly.
Possible effects are none, slow response, or machine down.
The CLIMATRAK Compressor driver detects an open, short, over
E03 876 11 2
voltage, or over temperature condition.
E03 1497 11 3 Unloading Auger Engage driver detects an open, short, over voltage,
or over temperature condition. The Left Control Unit cannot engage
the auger until the fault condition is removed.
E03 1500 09 3 CAN Bus message(s) missing from Cornerpost Control Unit -
Ground Speed and/or Machine Configuration.
E03 1503 09 3 CAN Bus message(s) missing from Armrest Control Unit
E03 1515 09 3 CAN Bus message(s) missing from Header Control Unit
E03 200112 03 2 12 V DC is detected at the output of Grain Tank Cover Fold relay
(K7) of the Control Relay Board when it is not energized. Indicates
possible problem with K7 or Control Power (cc# 016) short circuit
to 12 V DC.
E03 200112 04 2 12 V DC is not detected at the output of Grain Tank Cover Fold
relay (K7) of the Control Relay Board when it is energized.
Indicates possible problem with K7 or Control Power (cc# 016).
E03 200126 11 3 The Unloading Auger Swing In driver or the Unloading Auger
Swing Out driver detects an open, short, over voltage, or over
temperature condition. The Left Control Unit cannot swing the auger
until the fault condition is removed.
E03 200128 03 1 HILLMASTER II Engage is not ON, but 12 V DC is detected on the
Hillmaster Engage Signal (cc# 447) of the Left Control Unit.
Possible problem with Left Control Unit or Hillmaster Engage
Signal (cc# 447) shorted to 12 V DC
E03 200128 04 1 Hillmaster Engage Signal (cc# 447) is not 12 V DC when ON.
Possible problem with Left Control Unit or Hillmaster Engage
Signal (cc# 447) wiring. When HILLMASTER II is disengaged, the
Diagnostic Trouble Code becomes a stored code.

E03 200129 11 3 The Combine Lower driver detects an open, short, over voltage, or
over temperature condition. The Left Control Unit cannot engage
Combine Lower until the fault condition is removed.
E03 200132 11 1 The Left Brake Light driver detects an open, short, over voltage, or
over temperature condition. Only active in the ROAD mode.
E03 200133 11 1 The Right Brake Light driver detects an open, short, over voltage, or
over temperature condition. Only active in the ROAD mode.

http://slidepdf.com/reader/full/jhon-deere-dtcpdf 22/27
7/25/2019 Jhon Deere DTC.pdf

E03 200134 11 1 The Left Marker Light driver detects an open, short, over voltage, or
over temperature condition. Only active in the ROAD mode.
E03 200135 11 1 The Right Marker Light driver detects an open, short, over voltage,
or over temperature condition. Only active in the ROAD mode.
E03 200137 11 2 The Feeder House Reverser driver detects an open, short, over
voltage, or over temperature condition.
E03 200140 03 2 12 V DC detected on Ground (cc# 010) of Control Relay Board.
Indicates problem with ground connections.

OUZXMAG,00018B6 -19-10OCT02-24/27

Control
SPN FMI Pri. Description
Unit
E03 200141 04 2 12 V DC not detected on Unswitched Electronic Power (cc# 022) of
Control Relay Board. Indicates problem with Unswitched Electronic
Power connection, wiring or Fuse F20 of the Engine Compartment
Relay Panel.
E03 200142 04 2 12 V DC not detected on Light Power (cc# 014) of Control Relay
Board. Indicates problem with Light Power connection, wiring or
Fuse F18 of the Engine Compartment Relay Panel.

E03 200143 04 2 12Board.

V DCIndicates
not detected on Control
problem Power Power
with Control (cc# 016) of Control
connection, Relay
wiring,
Fuse F8 or Relay K4 of the Engine Compartment Relay Panel.
E03 200144 04 2 12 V DC not detected on Light Power 2 (cc# 046) of Control Relay
Board. Indicates problem with Light Power 2 connection, wiring or
Fuse F5 of the Engine Compartment Relay Panel.
E03 200145 04 2 12 V DC not detected on Light Power 3 (cc# 047) of Control Relay
Board. Indicates problem with Light Power 3 connection, wiring or
Fuse F3 of the Engine Compartment Relay Panel.
E03 200146 04 3 12 V DC not detected on Light Power 4 (cc# 048) of Control Relay
Board. Indicates problem with Light Power 4 connection, wiring or
Fuse F4 of the Engine Compartment Relay Panel.
E03 200147 04 2 12 V DC not detected on Fan Speed Adjust Power (cc# 051) of
Control Relay Board. Indicates problem with Fan Speed Adjust
Power connection, wiring or Fuse F11 or Relay K5 of the Engine
Compartment Relay Panel.
E03 200148 04 2 12 V DC not detected on Light Power 5 (cc# 049) of Control Relay
Board. Indicates problem with Light Power 5 connection, wiring or

http://slidepdf.com/reader/full/jhon-deere-dtcpdf 23/27
7/25/2019 Jhon Deere DTC.pdf

Fuse F9 of the Engine Compartment Relay Panel.

E03 200149 11 2 Indicates a problem in the serial communication link between the
Left Control Unit and the Control Relay Board.

Left Control Unit 2 Type Identification

The Left Control Unit 2 will have 1 or 2

connectors.

If the Left Control Unit 2 has one 30 pin

connector, it is a Type A control unit. If the
Left Control Unit 2 has 2 connectors, it is a
Type B control unit
OUZXMAG,00018B6 -19-10OCT02-25/27

E04 - Left Control Unit 2 Diagnostic Trouble

Codes

Control
SPN FMI Pri. Description
Unit
E04 190 09 3 CAN Bus message(s) missing from Engine Control Unit - Engine
Speed

E04 627 03 1 Delayed

DC. Power (cc# 006) voltage is too high - greater than 15.5 V
Controller cannot exit boot block program. Disconnect Left Control
E04 628 12 2 Unit 2 connectors X314 and X315. Reconnect connectors. Replace
Armrest Control Unit if condition persists. (Type B only)
E04 630 11 3 EEPROM failed test on power up. Replace the Left Control Unit 2 if
condition persists.
CAN Bus off - There are more than 256 CAN Bus errors (Type B
E04 639 19 3
only)
E04 1500 09 3 CAN Bus message(s) missing from Cornerpost Control Unit
E04 1503 09 2 CAN Bus message(s) missing from Armrest Control Unit
E04 200150 11 3 Threshing Speed failed to reach commanded speed after 50 seconds
E04 200151 11 3 Threshing Clearance failed to reach commanded clearance after 30
seconds
E04 200152 11 3 Cleaning Fan Speed failed to reach commanded speed after 130
seconds

http://slidepdf.com/reader/full/jhon-deere-dtcpdf 24/27
7/25/2019 Jhon Deere DTC.pdf

Left Chaffer Actuator Limit Switch problem. Pulses present on

E04 200310 11 3 Chaffer 1 Position (cc# 824). Limit switch remains on. (Type B
only)
Left Sieve Actuator Limit Switch problem. Pulses present on Sieve 1
E04 200311 11 3
Position (cc# 825). Limit switch remains on. (Type B only)
Left Precleaner Actuator Limit Switch problem. Pulses present on
E04 200312 11 3 Precleaner 1 Position (cc# 823). Limit switch remains on. (Type B
only)
Right Chaffer Actuator Limit Switch problem. Pulses present on
E04 200313 11 3 Chaffer 2 Position (cc# 819). Limit switch remains on. (Type B
only)
Right Sieve Actuator Limit Switch problem. Pulses present on Sieve
E04 200314 11 3
2 Position (cc# 827). Limit switch remains on. (Type B only)
Right Precleaner Actuator Limit Switch problem. Pulses present on
E04 200315 11 3 Precleaner 2 Position (cc# 818). Limit switch remains on. (Type B
only)
Left Chaffer Actuator commanded to move, but no pulses present on
E04 200316 11 3 Chaffer 1 Position (cc# 824). Actuator is in a valid position. (Type B
only)
Left Sieve Actuator commanded to move, but no pulses present on
E04 200317 11 3 Sieve 1 Position (cc# 825). Actuator is in a valid position. (Type B
only)
Left Precleaner Actuator commanded to move, but no pulses present
E04 200318 11 3 on Precleaner 1 Position (cc# 823). Actuator is in a valid position.
(Type B only)
Right Chaffer Actuator commanded to move, but no pulses present
E04 200319 11 3 on Chaffer 2 Position (cc# 819). Actuator is in a valid position.
(Type B only)
Right Sieve Actuator commanded to move, but no pulses present on
E04 200320 11 3 Sieve 2 Position (cc# 827). Actuator is in a valid position. (Type B
only)
Right Precleaner Actuator commanded to move, but no pulses
E04 200321 11 3 present on Precleaner 2 Position (cc# 818). Actuator is in a valid
position. (Type B only)

E04 200322 11 3 Power present

seconds. (Typeon
B Chaffer
only) Open Signal (cc# 374) for longer than 30
Power present on Chaffer Close Signal (cc# 375) for longer than 30
E04 200323 11 3
seconds. (Type B only)
Power present on Sieve Open Signal (cc# 376) for longer than 30
E04 200324 11 3
seconds. (Type B only)
E04 200325 11 3 Power present on Sieve Close Signal (cc# 377) for longer than 30

http://slidepdf.com/reader/full/jhon-deere-dtcpdf 25/27
7/25/2019 Jhon Deere DTC.pdf

seconds. (Type B only)

Power present on Precleaner Open Signal (cc# 372) for longer than
E04 200326 11 3
30 seconds. (Type B only)
Power present on Precleaner Close Signal (cc# 373) for longer than
E04 200327 11 3
30 seconds. (Type B only)

OUZXMAG,00018B6 -19-10OCT02-26/27

Control
SPN FMI Pri. Description
Unit

E04 200328 03 3 A shortnot

2 will circuit to ground
actuate the Leftdetected
Chaffer on cc# 385.
Actuator The
until theLeft Control
fault Unit
condition
is removed. (Type B only)
A short circuit to power detected on cc# 385 or 384. The Left
E04 200329 04 3 Control Unit 2 will not actuate the Left Chaffer Actuator until the
fault condition is removed. (Type B only)
A short circuit to ground detected on cc# 384. The Left Control Unit
E04 200330 03 3 2 will not actuate the Left Chaffer Actuator until the fault condition
is removed. (Type B only)
A short circuit to ground detected on cc# 387. The Left Control Unit

E04 200331 03 3 2removed.

will not (Type
actuateBthe Left Sieve Actuator until the fault condition is
only)
A short circuit to power detected on cc# 387 or 386. The Left
E04 200332 04 3 Control Unit 2 will not actuate the Left Sieve Actuator until the fault
condition is removed. (Type B only)
A short circuit to ground detected on cc# 386. The Left Control Unit
E04 200333 03 3 2 will not actuate the Left Sieve Actuator until the fault condition is
removed. (Type B only)
A short circuit to ground detected on cc# 383. The Left Control Unit
E04 200334 03 3 2 will not actuate the Left Precleaner Actuator until the fault
condition is removed. (Type B only)
A short circuit to power detected on cc# 383 or 382. The Left
E04 200335 04 3 Control Unit 2 will not actuate the Left Precleaner Actuator until the
fault condition is removed. (Type B only)
A short circuit to ground detected on cc# 382. The Left Control Unit
E04 200336 03 3 2 will not actuate the Left Precleaner Actuator until the fault
condition is removed. (Type B only)

http://slidepdf.com/reader/full/jhon-deere-dtcpdf 26/27
7/25/2019 Jhon Deere DTC.pdf

A short circuit to ground detected on cc# 393. The Left Control Unit
E04 200337 03 3 2 will not actuate the Right Chaffer Actuator until the fault condition
is removed. (Type B only)
A short circuit to power detected on cc# 393 or 392. The Left
E04 200338 04 3 Control Unit 2 will not actuate the Right Chaffer Actuator until the
fault condition is removed. (Type B only)
A short circuit to ground detected on cc# 392. The Left Control Unit
E04 200339 03 3 2 will not actuate the Right Chaffer Actuator until the fault condition
is removed. (Type B only)
A short circuit to ground detected on cc# 395. The Left Control Unit
E04 200340 03 3 2 will not actuate the Right Sieve Actuator until the fault condition
is removed. (Type B only)
A short circuit to power detected on cc# 395 or 394. The Left
E04 200341 04 3 Control Unit 2 will not actuate the Right Sieve Actuator until the
fault condition is removed. (Type B only)
A short circuit to ground detected on cc# 394. The Left Control Unit
E04 200342 03 3 2 will not actuate the Right Sieve Actuator until the fault condition
is removed. (Type B only)
A short circuit to ground detected on cc# 389. The Left Control Unit
E04 200343 03 3 2 will not actuate the Right Precleaner Actuator until the fault
condition is removed. (Type B only)
A short circuit to power detected on cc# 389 or 388. The Left
E04 200344 04 3 Control Unit 2 will not actuate the Right Precleaner Actuator until
the fault condition is removed. (Type B only)
A short circuit to ground detected on cc# 388. The Left Control Unit
E04 200345 03 3 2 will not actuate the Right Precleaner Actuator until the fault
condition is removed. (Type B only)
E04 200352 11 3 Chaffer Actuators not calibrated. (Type B only)
E04 200353 11 3 Sieve Actuators not calibrated. (Type B only)
E04 200354 11 3 Precleaner Actuators not calibrated. (Type B only)

OUZXMAG,00018B6 -19-10OCT02-27/27

http://slidepdf.com/reader/full/jhon-deere-dtcpdf 27/27