TECHNICAL DATA SHEET FEVICOL 1K PUR
FOR INFORMATION ONLY
PROPERTIES
COLOUR: Brownish Liquid Fevicol 1K PUR is a one component ready
to use moisture curing polyurethane
APPLICATION CONSISTENCY adhesive with gap filling properties.
Brush, Spatula, nozzle applicator
Fevicol 1K PUR adhesive is a very fast
AVERAGE WEIGHT setting adhesive. Initial handling strength is
3
1.0-1.2 Kg/m achieved within 30 minutes.
AVERAGE NON-VOLATILE (PIL method) Fevicol 1K PUR adhesive is designed to
Not less than 99.5% by weight adhere wood, MDF, fiberboard,
particleboard, metal, laminates, stone,
VISCOSITY (Brookfield RVT) ceramic, brick, foam, fiberglass, marble,
30-60 PS plasterboard, masonry, rubber, some plastics
and many other substrates.
WATER RESISTANCE (DIN EN 204/D4) Fevicol 1K PUR adhesive can be used in
(Test report 505 32054/2e, dated August edge to edge joints, I- beam joints. It is
2006, ift Rosenheim, Germany) suitable for bonding tropical wood, sandwich
Confirms to German DIN standard for panels. Typical applications in window, door,
boiling water resistance. pillar. It gives an exceptionally high
mechanical strength.
HEAT RESISTANCE (WATT 91) Fevicol 1K PUR is specially designed for
(Test by ift Rosenheim, Germany) exterior weather condition. The adhesive
Confirms to high heat resistance as per bond is resistance to cold and hot weather
WATT91. conditions.
2
Adhesive Strength 12.8 N/mm
Fevicol 1K PUR gives a clear glue line on
COVERAGE RANGE (PSTM WI 1069) drying that can be sanded, painted or
(Subject to type of surface coated) stained.
8.0 – 9.0 m2/Kg
VOC - 1.0 g/L max
PIDILITE INDUSTRIES LIMITED
Fevicol Division: P.B. No. 17411, Andheri (East), Mumbai 400 059 (India),
Phone +91-22-28367085, Fax: +91-22-28357853, website: www.pidilite.com
2
APPLICATION GUIDE FOR FEVICOL 1K PUR
MATERIAL PREPARATION
Surface to be bonded should be dry, clean, and free from oil or grease.
APPLICATION
By Brush/Roller/Spatula
Apply to one surface in a thin layer, assemble the parts and leave to set, it will set in
30mininutes. During cure this product will expand to fill gaps and rough surfaces, when
foamed. Firmly clamp both the substrates. A strong bond will be obtained after 2 - 3
hours and full strength will be realized after 24 hours at room temperature. Individual
substrates should be evaluated for bonding performance prior to any large scale
application.
CLEAN-UP
Mineral spirit or acetone when glue is wet, sand & scrape when glue is dry.
STORAGE
Being a highly reactive moisture curing system, any water contamination of the
container will cause problems. Once opened therefore, the glue should be used up as
quickly as possible.
HANDLING
Adhesive is based on diphenyl methane-4, 4-di-isocyanate and is therefore classed as
harmful. Wear suitable rubber gloves and eye protective while handling. Keep out of
reach of children.
SHELF LIFE
Best before nine months from the date of manufacturing in factory sealed container.
PACKING
500 g, 20 Kg.
IMPORTANT
We recommend that before using our product, the customer should make his own test to determine the
suitability of the product for his own purpose under his operating conditions. As the circumstances under
which our product is stored, handled and used, are beyond our control. We cannot assume any
responsibility of their use by the customer.
Specifications are subject to change. Current specification is available with HO Marketing and can be provided on request.
Consult Material Safety Data Sheet and Container label for further information.
Revised on 25/03/2013
***
