Owner’s Man
Owner’s ual
Manual
Model Numbers: P/N 12626
THB-2500,THB-2510, Date 08-10-01
TBL-4600,TBL-4610,TBL-505
BLOWERS
BLO
TBL-4600
THB-2510
Supplier To The Outdoor Power Equipment Industry
ISM, Inc. • 1028 4th Street SW • Auburn, WA 98001 • Phone: (253) 333-1200 • Fax: (253) 333-1212
www.tanakapowerequipment.com [email protected]
THB-2500/THB-2510/TBL-4600/4610,TBL-505 Owner’s Manual
Before using this unit:
• Read the operator’s manual carefully.
• Check that the blower is correctly assembled
and adjusted.
• Start the unit and check the carburetor adjustment.
See “Maintenance”.
WARNING
The engine exhaust from this product
contains chemicals known to the State
of California to cause cancer, birth
defects and other reproductive harm.
Always wear eye, head and ear protectors Read, understand and follow all warnings and
when using this unit. instructions in this manual and on the unit.
It is important that you read, fully understand and observe
the following safety precautions and warnings. Careless or
improper use of the unit may cause serious or fatal injury.
WARNING DANGER
Explains choke position. Upper sign indicates
choke closed and the lower fully open. Keep hands off from rotating fan. For vacuum,
vacuum pipe and bag must be in place. For
blower, dust cover must be securely installed.
www.tanakapowerequipment.com 1 [email protected]
THB-2500/THB-2510/TBL-4600/4610,TBL-505 Owner’s Manual
www.tanakapowerequipment.com 2 [email protected]
THB-2500/THB-2510/TBL-4600/4610,TBL-505 Owner’s Manual
2. Warnings and safety instructions.
Operator Safety
Blowing Safety
• IMPORTANT: A dust filter mask should be worn during
• Operate power equipment only at reasonable hours-not early
operation.
in the morning or late at night when people might be
• Always wear a safety face shield or goggles. Always wear
disturbed. Comply with times listed in local ordinances. Usual
heavy, long pants, boots and gloves. Do not wear loose
recommendations are 9:00 a.m. to 5:00 p.m., Monday
clothing, jewelry, short pants, sandals or go barefoot. Secure
through Saturday.
hair so it is above shoulder length.
• Never direct discharge of air toward bystanders nor allow
• Do not operate that tool when you are tired, ill or under the
anyone near the area of operation. Use care in directing
influence of alcohol, drugs or medication.
discharge to avoid glass enclosures, automobiles, etc.
• Never let a child or inexperienced person operate the
• Stay alert for uneven sidewalks, holes in terrain or other
machine.
unstable condition when using the tool.
• Wear hearing protection.
• Take all possible precautions when leaving the tool
• Never start or run the engine inside a closed room or
unattended such as stopping the engine.
building. Breathing exhaust fumes can kill.
• Never operate the tool without guards, blow pipes or other
• Keep handles free of oil and fuel.
protective device in place. (if so equipped.)
• Keep hands away from moving part or heated area.
• Keep others including children, animals, bystanders and
• Do not grab or hold the unit by the blow pipe.
helpers outside the 15 m (50ft) hazard zone. Stop the
• When the unit is turned off, make sure the engine has
engine immediately if you are approached.
stopped before the unit is set down.
• Always keep the engine on the right side of your body.
• When operation is prolonged, take a break from time to time
(Hand held blower only)
so that you may avoid possible whitefinger disease which is
• Keep firm footing and balance. Do not over-reach.
caused by vibration.
• Keep all parts of your body away from the muffler.
Tool Safety
Maintenance Safety
• Inspect the entire tool before each use. Replace damaged
• Maintain the tool according to recommended procedures.
parts. Check for fuel leaks and make sure all fasteners are in
• Disconnect the spark plug before performing maintenance
place and securely fastened.
except for carburetor adjustments.
• Replace parts that are cracked, chipped or damaged in any
• Keep others away when making carburetor adjustments.
way before using the tool.
• Use only genuine replacement parts as recommended by the
• Make sure the safety guard is properly attached.
manufacturer.
• Keep others away when making carburetor adjustments.
• Use only accessories as recommended for this tool by the
Transport and storage
manufacturer.
• Carry the tool by hand with the engine stopped and the
muffler away from your body.
WARNING!
• Allow the engine to cool, empty the fuel tank, and secure the
Never modify the tool in any way. Do not use the tool for any job
tool before storing or transporting in a vehicle.
except that for which it is intended.
• Empty the fuel tank before storing the tool. It is
recommended that the fuel be emptied after each use.
Fuel Safety
If fuel is left in the tank, store so fuel will not leak.
• Mix and pour fuel outdoors and where there are no sparks or
• Store tool out of the reach of children.
flames.
• Clean the unit carefully and store it in a dry place.
• Use a container approved for fuel.
• Make sure engine switch is off when transporting or storing.
• Do not smoke or allow smoking near fuel or the tool or while
using the tool.
If situations occur which are not covered in this manual, take care and
• Wipe up all fuel spills before starting engine.
have good judgment. Contact your dealer if you need assistance.
• Move at least 3 m (10 ft) away from fueling site before
starting engine.
Pay special attention to statements preceded by the following words:
• Stop engine before removing fuel cap.
• Empty the fuel tank before storing the tool. It is
WARNING!
recommended that the fuel be emptied after each use. If
Indicates a strong possibility of severe personal injury or loss of life, if
fuel is left in the tank, store so fuel will not leak.
instructions are not followed.
• Store tool and fuel in area where fuel vapors cannot reach
sparks or open flames from water heaters, electric motors or
CAUTION!
switches, furnaces, etc.
Indicates a possibility of personal injury or equipment damage, if
instructions are not followed.
WARNING!
Antivibration systems do not guarantee that you will not sustain
NOTE!
whitefinger disease or carpal tunnel syndrome. Therefore, continual
Helpful information for correct function and use.
and regular users should monitor closely the condition of their hands
and fingers. If any of the above symptoms appear, seek medical advice
immediately.
www.tanakapowerequipment.com 3 [email protected]
THB-2500/THB-2510/TBL-4600/4610,TBL-505 Owner’s Manual
Fig. 1
1
3. Assembly procedures.
Blow pipes to main body (Fig. 1-1)
Inspect the main body and accessories,
Connect straight pipe (1) and other pipe(s)
securely. (See page 1)
Align groove (2) in straight pipe with projection (3) on blower housing (or another pipe) and slide the pipe onto the blower
housing (or another pipe).
Rotate the pipe clockwise to lock it into place, then tighten the clamp band (if so equipped, THB-2510).
NOTE! (TBL-4600, optional)
• Connect flexible pipe (2) to main body with clamp (1).
Finger-tighten the clamp.
• Connect swivel pipe (4) to flexible pipe with clamp (3).
• Install throttle grip (5) to swivel pipe so that the grip locates 2-3 cm away from projection (6) on swivel pipe.
• Finally, if direction of bent pipe does not match the direction of throttle grip, loosen knob (7) or wing bolt (8) (enclosed in
vinyl bag) and swivel the grip to your comfort. (Fig. 1 - 1 B)
NOTE! (TBL-4600/4610/505, optional)
• Use flexible pipe with wire clamps.
• Install the pipe handle on swivel pipe or on straight pipe. Decide
location and direction to your comfort.
(Fig. 1-2)
NOTE! (THB-2510, optional)
Vacuum attachment is offered as an optional kit, which converts the hand-held blower into a vacuum cleaner. For installation,
see THV-200 vacuum manual.
www.tanakapowerequipment.com 4 [email protected]
THB-2500/THB-2510/TBL-4600/4610,TBL-505
Owner’s Manual
4. Operating procedures.
WARNING!
This unit is equipped with a two-stroke engine. Always run the engine on fuel, which is mixed with oil.
Provide good ventilation, when fueling or handling fuel.
Fuel
• Always use branded 89 octane unleaded gasoline.
• Use Tanaka two-cycle oil or a quality two-cycle oil at mixing ratio of 25-50:1 (Gasoline (A) : Oil (B)), only for the state of
California at 50: 1.
• Never use multi-grade oil (10 W/30) or waste oil.
• Always mix fuel and oil in a separate clean container.
Always start by filling half the amount of fuel, which is to be used. Then add the whole amount of oil. Mix (shake) the fuel
mixture.
Add the remaining amount of fuel.
Mix (shake) the fuel-mix thoroughly before filling the fuel tank.
Fueling
WARNING!
* Always shut off the engine before refueling.
*Slowly open the fuel tank, when filling up with fuel, so that possible over-pressure disappears.
Tighten the fuel cap carefully, after fueling.
*Always move the unit at least 3 m (10 ft.) from the fueling area before starting.
Before fueling, clean the tank cap area carefully, to ensure that no dirt falls into the tank.
Make sure that the fuel is well mixed by shaking the container, before fueling.
www.tanakapowerequipment.com 5 [email protected]
THB-2500/THB-2510/TBL-4600/4610,TBL-505
Owner’s Manual
Starting
CAUTION!
Do not start if the pipe is obstructed by the ground or any other object.
1 .Set ignition switch (1) to ON position.
(Fig. 2-2, 2B, 2C)
• Push priming bulb (4) several times so that fuel flows through return pipe (5) (if so equipped) (Fig. 2-3, 3B)
• Move throttle lever to a half-open position (2) and lock it with lock lever (4) (if so equipped), when it is hard to
start engine. (Fig. 2-2C)
Note! (TBL-4610)
Model TBL-4610 does not have an ignition switch.
To start or to stop the unit, ignore the switch operation from procedures in the manual. However, when
starting the unit, move throttle lever to START position.
2. Set choke lever to CLOSED position (4). Fig. 2-4, 4B
3. Pull recoil starter briskly, taking care to keep the handle in your grasp
and not allowing it to snap back. (Fig. 2-5, 5B)
4. When you hear the engine want to start, return choke lever to RUN
position (open). Then pull recoil starter briskly again.
NOTE!
If engine does not start, repeat procedures from 2 to 4.
5. After starting engine, allow the engine about 2-3 minutes to warm up
before subjecting it to any load.
www.tanakapowerequipment.com 6 [email protected]
THB-2500/THB-2510/TBL-4600/4610,TBL-505
Owner’s Manual
Operating blower (Fig. 2-6, 6B)
Adjust shoulder harness to fit your stature before operating unit. Back-pack unit in a correct way. (Fig. 2-6B)
WARNING!
Do not direct discharge of air toward people or pet.
1. The unit should be operated in a well ventilated area.
2. A low speed should be used to blow leaves and dry grass.
3. A medium speed should be used to clean wet leaves and grass.
4. A high speed should be used when moving gravel, dirt or other heavy materials.
CAUTION!
This blower has been designed and adjusted to be used with all blower pipes attached (See page 1). It must never be
operated without the straight pipe, and blow head.
Stopping (Fig. 2-7, 7B, 7C)
Decrease engine speed, and push ignition switch to stop position.
Note! (TBL-4610)
Model TBL-4610 does not have an ignition switch.
To stop the unit, move throttle lever to START position and run for a few minutes, then move the lever further to STOP
position.
www.tanakapowerequipment.com 7 [email protected]
THB-2500/THB-2510/TBL-4600/4610,TBL-505
Owner’s Manual
5. Maintenance
MAINTENANCE, REPLACEMENT, OR REPAIR OF THE EMISSION CONTROL DEVICES AND SYSTEM MAY BE
PERFORMED BY ANY NONROAD ENGINE REPAIR ESTABLISHMENT OR INDIVIDUAL.
Carburetor adjustment (Fig. 3-1, 1 B, IC)
In the carburetor, fuel is mixed with air. When the engine is test run at the factory, the carburetor is basically
adjusted. A further adjustment may be required, according to climate and altitude. The carburetor has one adjustment
possibility:
T = Idle speed adjustment screw.
Idle speed adjustment (T)
To adjust, turn IDLE Adjustment Screw (T) in (clockwise) to increase engine speed, out (counterclockwise) to
decrease engine speed.
Standard Idle rpm is 2500-3000rpm.
CAUTION!
The above adjusting procedure must be followed when adjustment is MADE or DAMAGE to engine will occur because of
the incorrect condition.
RECOMMENDATION:
CARBURETOR ADJUSTMENT NEEDS THE SKILL OF EXPERIENCED OR WELL TRAINED PEOPLE. IT IS RECOMMENDED TO
TAKE THE UNIT TO YOUR NEAREST DEALER.
www.tanakapowerequipment.com 8 [email protected]
THB-2500/THB-2510/TBL-4600/4610,TBL-505
Owner’s Manual
Air filter
The air filter must be cleaned from dust and dirt in order to avoid:
• Carburetor malfunctions.
• Starting problems.
• Engine power reduction.
• Unnecessary wear on the engine parts.
• Abnormal fuel consumption.
Remove the air cleaner cover by pushing and pulling back the tab on the top. (Fig. 3-2)
Cleaning the air filter
Clean the cleaner element every day or every 8 hours of operation. More frequent cleaning is recommended under
very dusty conditions. Wash the element in liquid detergent and water. Squeeze the element to remove the dirt. Press
the element in a dry rag until it is completely dry. Saturate the element in 2-cycle oil or the equivalent. Squeeze the
element to distribute the oil completely and to remove any excess oil. Replace the element and install the cover. (Fig.
3-2B, 2C)
Fuel filter (Fig. 3-3, 3B)
Drain all fuel from fuel tank and pull fuel filter line from tank. Pull filter element out of holder assembly and rinse
element in warm water with detergent.
Rinse thoroughly until all traces of detergent are eliminated. Squeeze, do not wring, away excess water and allow
element to air dry.
NOTE!
If element is hard due to excessive dirt buildup, replace it.
www.tanakapowerequipment.com 9 [email protected]
THB-2500/THB-2510/TBL-4600/4610,TBL-505
Owner’s Manual
Spark plug (Fig. 3-4)
The spark plug condition is influenced by:
• An incorrect carburetor setting.
• Wrong fuel mixture (too much oil in the gasoline)
• A dirty air filter.
• Hard running conditions (such as cold weather).
These factors cause deposits on the spark plug electrodes, which may result in malfunction and starting difficulties. If
the engine is low on power, difficult to start or runs poorly at idling speed, always check the spark plug first. If the
spark plug is dirty, clean it and check the electrode gap. Readjust if necessary. The correct gap is 0.6 mm (.024”). The
spark plug should be replaced after about 100 operation hours or earlier if the electrodes are badly eroded.
NOTE!
In some areas, local law requires using a resistor spark plug to suppress ignition signals. If this machine was originally
equipped with resistor spark plug, use same type of spark plug for replacement.
Muffler (Fig. 3-5, 5B,5C)
Remove the muffler and clean out any excess carbon from the exhaust port or muffler inlet every 100 hours of
operation.
Cylinder (Engine cooling) (Fig. 3-6, 6B)
The engine is air cooled, and air must circulate freely around engine and over cooling fins on cylinder head to prevent
overheating.
Every 100 Operating hours, or once a year (more often if conditions require), clean fins and external surfaces of engine
of dust, dirt and oil deposits which can contribute to improper cooling.
NOTE!
Do not operate engine with engine shroud or muffler guard removed as this will cause overheating and engine damage.
Spark arrestor
If your unit comes with spark arrestor screen and yet your local regulation requires use of spark arrestor for prevention
against a possible fire, please attach it to the muffler by removing muffler protector and other related parts.
(The spark arrestor meets the regulation of SAE J335-SEP90 and CSA CAN3-Z62. 1 -M77)
www.tanakapowerequipment.com 10 [email protected]
THB-2500/THB-2510/TBL-4600/4610,TBL-505
Owner’s Manual
Maintenance schedule
Below you will find some general maintenance instructions. For further information
please contact your service dealer.
Daily maintenance
• Clean the exterior of the unit.
• Check the dust cover for damage or cracks. Change the cover in case of impacts or
cracks. (Hand held blower only)
• Check that nuts and screws are sufficiently tightened.
Weekly maintenance
• Check the starter, especially cord and return spring.
• Clean the exterior of the spark plug.
• Remove it and check the electrode gap. Adjust it to 0.6 mm (.024”), or change the
spark plug.
• Clean the cooling fins on the cylinder and check that the air intake at the starter is
not clogged.
• Clean the air filter.
Monthly maintenance
• Rinse the fuel tank with gasoline.
• Clean the exterior of the carburetor and the space around it.
• Clean the fan and the space around it.
www.tanakapowerequipment.com 11 [email protected]
THB-2500/THB-2510/TBL-4600/4610,TBL-505
Owner’s Manual
6. Specifications
ANSI : Measured at 50 feet away from unit.
CEN : Measured at operator's ear.
NOTE : Equivalent noise level/vibration levels are calculated as the time-weighted energy total for noise/vibration levels
under various working conditions with the following time distribution : ½ idle, ½ full speed.
* All data subject to change without notice.
www.tanakapowerequipment.com 12 [email protected]
THB-2500/THB-2510/TBL-4600/4610,TBL-505
Owner’s Manual
Declaration of conformity
Declaration de conformite
Dichiarazione di conformita
Konformitiitserkliirung
Declaraci6n de conformidad
Konformitetsdeklaration
We, Tanaka Kogyo Co., Ltd., 3-4-29 Tsudanuma, Narashino, Chiba, Japan
Nous,soussign6s,
Noi,
Der unterzeichnete,
Nosotros,
vi,
Declare under our sole responsibility that the product, power blower model THB-25 10, TBL-4600/4610/5O5
D6clarons sous notre seule responsabilitd que le produit en question, souffleuse mdcanique mod~le
Dichiariamo sotto la nostra unica responsabilita che it prodotto, it motosoffiatore modello
Erklarl unter, eigener Verantwortung, daB das Produkt, motorgeblase model]
Declaramos dajo nuestra Onica responsabilidad que el producto, soplador mecdnico modelo
Forklarar harmed pA eget ansvar att denna produkt, motordriven grdsmattsluftare modell
to which this declaration relates is in conformity with the essential safety requirements of directives.
laquelle se rapporte la pr6sente d6claration est conforme aux directives concernant les conditions de s6curit6
essentielles.
at quale questa dichiarazione si riferisce, ~ conforme ai requisiti di sicurezza essenziali delle direttive.
for das these Erklarung gilt, den wesentlichen Sicherheitsanforderungen der Directive entspricht.
que corresponde a esta declaracl6n, satisface la (s) siguiente (s) exigencia (s) de seguridad esencial (es) de las
directivas.
till vilken denna deklaration tillhor, uppfyller samtliga vasentliga sakerhetskrav f6reskrivna 1 ber6rda direktiv.
89/392/EEC, 91/368/EEC, 93/44/EEC, 93/68/EEC, EMC89/336/EEC
The following standards have been taken into consideration IS03864, (EN-292-2)
Les normes suivantes ont 6t6 prises en consid6ration. Sono
stati presi in considerazione 1 seguenti standard. Die
nachfolgenden Standards wurden in Betracht gezogen. Se ban
tenido en consideraci6n las siguientes normas. Vi har tagit
hansyn till f6ljande standards.
Manufactured at: Chiba, Japan Serial No. up from v001001
Fait A: No. de s6rie A partir de
Luogo: Num. di serie da
Erstellt in: Scrien-Nr. ab
Fabricado en: No. de Serie de
en adelante
Tillverkad av: Serienr fr. o.m.
Signature:
Signature:
Firma: Sejii Tanaka
Unterschrift:
Fimado:
Signatur:
Position: Vice president
Function: Vice-pr6sident
Incarico: Vicepresidente
Titel: Stellvertretender Vorsitzender
Cargo: Vicepresidente
Befattning: Vice President
www.tanakapowerequipment.com 13 [email protected]
