Owner’s Manual

Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY”
and “IMPORTANT NOTES” (p. 2–3, p. 4). These sections provide important information
concerning the proper operation of the unit. Additionally, in order to feel assured that you
have gained a good grasp of every feature provided by your new unit, Owner’s manual
should be read in its entirety. The manual should be saved and kept on hand as a conve-
nient reference.

Copyright © 2004 ROLAND CORPORATION

All rights reserved. No part of this publication may be reproduced in any form without the written
permission of ROLAND CORPORATION.
USING THE UNIT SAFELY

Used for instructions intended to alert The symbol alerts the user to important instructions
the user to the risk of death or severe or warnings.The specific meaning of the symbol is
injury should the unit be used determined by the design contained within the
improperly. triangle. In the case of the symbol at left, it is used for
general cautions, warnings, or alerts to danger.
Used for instructions intended to alert
the user to the risk of injury or material The symbol alerts the user to items that must never
be carried out (are forbidden). The specific thing that
damage should the unit be used
must not be done is indicated by the design contained
improperly. within the circle. In the case of the symbol at left, it
* Material damage refers to damage or means that the unit must never be disassembled.
other adverse effects caused with The ● symbol alerts the user to things that must be
respect to the home and all its carried out. The specific thing that must be done is
furnishings, as well to domestic indicated by the design contained within the circle. In
animals or pets. the case of the symbol at left, it means that the power-
cord plug must be unplugged from the outlet.

001 009
• Before using this unit, make sure to read the • Do not excessively twist or bend the power cord,
instructions below, and the Owner’s Manual. nor place heavy objects on it. Doing so can
damage the cord, producing severed elements and
.......................................................................................................... short circuits. Damaged cords are fire and shock
002c
• Do not open (or modify in any way) the unit or its hazards!
AC adaptor. ..........................................................................................................
010
.......................................................................................................... • This unit, either alone or in combination with an
003 amplifier and headphones or speakers, may be
• Do not attempt to repair the unit, or replace parts capable of producing sound levels that could
within it (except when this manual provides cause permanent hearing loss. Do not operate for
specific instructions directing you to do so). Refer a long period of time at a high volume level, or at
all servicing to your retailer, the nearest Roland a level that is uncomfortable. If you experience
Service Center, or an authorized Roland any hearing loss or ringing in the ears, you should
distributor, as listed on the “Information” page. immediately stop using the unit, and consult an
.......................................................................................................... audiologist.
004
• Never use or store the unit in places that are: ..........................................................................................................
011
• Subject to temperature extremes (e.g., direct • Do not allow any objects (e.g., flammable material,
sunlight in an enclosed vehicle, near a heating coins, pins); or liquids of any kind (water, soft
duct, on top of heat-generating equipment); or drinks, etc.) to penetrate the unit.
are
• Damp (e.g., baths, washrooms, on wet floors);
..........................................................................................................
or are 012b
• Humid; or are • Immediately turn the power off, remove the AC
adaptor from the outlet, and request servicing by
• Exposed to rain; or are
your retailer, the nearest Roland Service Center, or
• Dusty; or are an authorized Roland distributor, as listed on the
• Subject to high levels of vibration. “Information” page when:
.......................................................................................................... • The AC adaptor, the power-supply cord, or the
007
• Make sure you always have the unit placed so it is plug has been damaged; or
level and sure to remain stable. Never place it on • If smoke or unusual odor occurs
stands that could wobble, or on inclined surfaces. • Objects have fallen into, or liquid has been
.......................................................................................................... spilled onto the unit; or
008c
• Be sure to use only the AC adaptor supplied with • The unit has been exposed to rain (or otherwise
the unit. Also, make sure the line voltage at the has become wet); or
installation matches the input voltage specified on • The unit does not appear to operate normally or
the AC adaptor’s body. Other AC adaptors may exhibits a marked change in performance.
use a different polarity, or be designed for a
different voltage, so their use could result in
damage, malfunction, or electric shock.

2
013 101b
• In households with small children, an adult • The unit and the AC adaptor should be located so
should provide supervision until the child is their location or position does not interfere with
capable of following all the rules essential for the their proper ventilation.
safe operation of the unit. ..........................................................................................................
.......................................................................................................... 102c
014 • Always grasp only the plug on the AC adaptor
• Protect the unit from strong impact. cord when plugging into, or unplugging from, an
(Do not drop it!) outlet or this unit.
..........................................................................................................
.......................................................................................................... 103b
015 • At regular intervals, you should unplug the AC
• Do not force the unit’s power-supply cord to share adaptor and clean it by using a dry cloth to wipe
an outlet with an unreasonable number of other all dust and other accumulations away from its
devices. Be especially careful when using prongs. Also, disconnect the power plug from the
extension cords—the total power used by all power outlet whenever the unit is to remain
devices you have connected to the extension unused for an extended period of time. Any
cord’s outlet must never exceed the power rating accumulation of dust between the power plug and
(watts/amperes) for the extension cord. Excessive the power outlet can result in poor insulation and
loads can cause the insulation on the cord to heat lead to fire.
up and eventually melt through. ..........................................................................................................
.......................................................................................................... 104
016 • Try to prevent cords and cables from becoming
• Before using the unit in a foreign country, consult entangled. Also, all cords and cables should be
with your retailer, the nearest Roland Service placed so they are out of the reach of children.
Center, or an authorized Roland distributor, as ..........................................................................................................
listed on the “Information” page. 106
• Never climb on top of, nor place heavy objects on
the unit.

..........................................................................................................
107c
• Never handle the AC adaptor or its plugs with
wet hands when plugging into, or unplugging
from, an outlet or this unit.
..........................................................................................................
108b
• Before moving the unit, disconnect the AC
adaptor and all cords coming from external
devices.
..........................................................................................................
109b
• Before cleaning the unit, turn off the power and
unplug the AC adaptor from the outlet (p. 10).

..........................................................................................................
110b
• Whenever you suspect the possibility of lightning
in your area, disconnect the AC adaptor from the
outlet.

3
 IMPORTANT NOTES
291a
In addition to the items listed under “USING THE UNIT SAFELY” on page 2–3, please read and observe the following:

Power Supply Repairs and Data

301 452
• Do not use this unit on the same power circuit with any • Please be aware that all data contained in the unit’s
device that will generate line noise (such as an electric memory may be lost when the unit is sent for repairs.
motor or variable lighting system). Important data should always be backed up in another
302 MIDI device (e.g., a sequencer), or written down on paper
• The AC adaptor will begin to generate heat after long (when possible). During repairs, due care is taken to avoid
hours of consecutive use. This is normal, and is not a the loss of data. However, in certain cases (such as when
cause for concern. circuitry related to memory itself is out of order), we
307
• Before connecting this unit to other devices, turn off the regret that it may not be possible to restore the data, and
power to all units. This will help prevent malfunctions Roland assumes no liability concerning such loss of data.
and/or damage to speakers or other devices.
Additional Precautions
Placement 551
• Please be aware that the contents of memory can be
351
• Using the unit near power amplifiers (or other equipment irretrievably lost as a result of a malfunction, or the
containing large power transformers) may induce hum. improper operation of the unit. To protect yourself against
To alleviate the problem, change the orientation of this the risk of losing important data, we recommend that you
unit; or move it farther away from the source of inter- periodically save a backup copy of important data you
ference. have stored in the unit’s memory in another MIDI device
352a (e.g., a sequencer).
• This device may interfere with radio and television 552
reception. Do not use this device in the vicinity of such • Unfortunately, it may be impossible to restore the contents
receivers. of data that was stored in another MIDI device (e.g., a
352b sequencer) once it has been lost. Roland Corporation
• Noise may be produced if wireless communications assumes no liability concerning such loss of data.
devices, such as cell phones, are operated in the vicinity of 553
this unit. Such noise could occur when receiving or initi- • Use a reasonable amount of care when using the unit’s
ating a call, or while conversing. Should you experience buttons, sliders, or other controls; and when using its jacks
such problems, you should relocate such wireless devices and connectors. Rough handling can lead to malfunctions.
556
so they are at a greater distance from this unit, or switch • When connecting / disconnecting all cables, grasp the
them off. connector itself—never pull on the cable. This way you
354a
• Do not expose the unit to direct sunlight, place it near will avoid causing shorts, or damage to the cable’s
devices that radiate heat, leave it inside an enclosed internal elements.
558a
vehicle, or otherwise subject it to temperature extremes. • To avoid disturbing your neighbors, try to keep the unit’s
Excessive heat can deform or discolor the unit. volume at reasonable levels. You may prefer to use
355b
• When moved from one location to another where the headphones, so you do not need to be concerned about
temperature and/or humidity is very different, water those around you (especially when it is late at night).
559a
droplets (condensation) may form inside the unit. Damage • When you need to transport the unit, package it in the box
or malfunction may result if you attempt to use the unit in (including padding) that it came in, if possible. Otherwise,
this condition. Therefore, before using the unit, you must you will need to use equivalent packaging materials.
allow it to stand for several hours, until the condensation 562
has completely evaporated. • Use a cable from Roland to make the connection. If using
some other make of connection cable, please note the
following precautions.
Maintenance • Some connection cables contain resistors. Do not use
401a cables that incorporate resistors for connecting to this
• For everyday cleaning wipe the unit with a soft, dry cloth unit. The use of such cables can cause the sound level
or one that has been slightly dampened with water. To to be extremely low, or impossible to hear. For infor-
remove stubborn dirt, use a cloth impregnated with a mation on cable specifications, contact the manufac-
mild, non-abrasive detergent. Afterwards, be sure to wipe turer of the cable.
the unit thoroughly with a soft, dry cloth.
402
• Never use benzine, thinners, alcohol or solvents of any
kind, to avoid the possibility of discoloration and/or 220
deformation. * All product names mentioned in this document are trade-
marks or registered trademarks of their respective owners.

4
 Introduction
The GR-20 is a guitar synthesizer (guitar synth) which contains a high-quality sound generator and is
designed for easy operation.
The GR-20 carefully analyses the pitch and volume of each string as it tracks the signals being output by the
divided pickup (a pickup installed on your guitar which outputs a separate signal for each string), and uses
this information to trigger its built-in sound generator. At the same time, a data stream interpreting your
guitar performance can also be transmitted via the MIDI OUT connector, and used to play an external MIDI
device, such as a sound module.

Main Features
• You can play more than 450 different types of synth sounds in the same way as when playing your guitar
conventionally.
• In addition to playing the synth sounds by themselves, you can combine the normal guitar sound with the
synth sound.
• When applying an external effects unit to the normal guitar sound, you can use the Mix In jack to mix the
processed sound with the synth sound.
• The GR-20 can be used with any steel-string guitar on which a GK-3 or GK-2A (divided pickup; sold
separately) can be correctly installed.
• The GR-20 can also be used with a bass guitar on which a GK-3B or GK-2B (divided pickup for bass guitar;
sold separately) is installed.
• Built-in effects (reverb, delay, chorus) are provided for the synth sound, creating a rich and spacious
ambiance. (p. 20)
• You can adjust and store settings such as attack and decay time, and effect depth. (p. 20)
• You can use the GR-20's two foot pedals to apply a Hold effect or Glide effect. (p. 15)
• Use the built-in expression pedal to control parameters such as volume or filter. (p. 16)
• Since your guitar performance is output as MIDI data, you can use your guitar to play an external sound
module or as an input device for your MIDI sequencer. (p. 28)
• A guitar tuner is built-in for quick and accurate tuning. (p. 13)

5
 Contents

USING THE UNIT SAFELY......................................................................2

IMPORTANT NOTES ...............................................................................4
Introduction .............................................................................................5
Main Features.............................................................................................................................................. 5

Names of Things and What They Do.....................................................8

Front Panel................................................................................................................................................... 8
Rear Panel .................................................................................................................................................. 10

Chapter 1 Play the Sounds! .................................................................11

Preparing Your Guitar ............................................................................................................................. 11
Connections ............................................................................................................................................... 11
Turning the Power On ............................................................................................................................. 12
Adjusting the Output Level .................................................................................................................... 12
Adjusting the Input Sensitivity (GK SENS).......................................................................................... 12
Tuning Your Guitar (Tuner Function)................................................................................................... 13
Specifying the Output Device (OUTPUT SELECT)............................................................................. 14
Selecting a Sound (Patch) ........................................................................................................................ 14
Using the Knob to Select Patches................................................................................................ 14
Using the Switches of the GK Pickup to Select Patches .......................................................... 15
Using the Foot Pedals to Select Patches ..................................................................................... 15
Using an External Device Via MIDI to Select Patches ............................................................. 15
Play the GR-20! ......................................................................................................................................... 15
Using the Foot Pedal to Change the Pitch (GLIDE) ............................................................................ 15
Using the Foot Pedal to Sustain the Sound (HOLD)........................................................................... 16
Using the Expression Pedal to Modify the Sound (EXP PEDAL) ..................................................... 16
Turning the Power Off............................................................................................................................. 16

Chapter 2 Using the GR-20 with Guitar Effects..................................17

Connections ............................................................................................................................................... 17
Switching between the Synth Sound and Guitar Sound .................................................................... 18
Using the GR-20 with a Multi-effects Unit ........................................................................................... 18
Channel (CH)................................................................................................................................. 18
Patch Link Setup (PATCH LINK SETUP) ................................................................................. 19

Chapter 3 Editing The Sounds.............................................................20

Selecting a Sound to Start From ............................................................................................................. 20
Use the Knobs to Adjust the Sound ....................................................................................................... 20
Adjusting the Attack—ATTACK................................................................................................ 20
Adjusting the Release—RELEASE.............................................................................................. 20
Adjusting the Spaciousness of the Sound—CHORUS ............................................................ 20
Adjusting the Reverberation—DELAY/REVERB.................................................................... 20
Adjusting the Volume—LEVEL.................................................................................................. 20

6
 Contents

Editing Other Parameters........................................................................................................................ 21

Adjusting the Brightness of the Sound—FREQ........................................................................ 21
Adding a Distinctive Character to the Tone—RESO ............................................................... 21
Adjusting the Pitch —TRANSPOSE........................................................................................... 21
Adjusting the Playing Feel—PLAY FEEL.................................................................................. 21
Selecting the Type of Glide Effect—GLIDE TYPE............................................................................... 22
Selecting the Type of Hold Effect—HOLD TYPE................................................................................ 23
Selecting the Effect Controlled by the Expression Pedal—EXP PEDAL.......................................... 23
Storing the Sounds You Create (WRITE) .............................................................................................. 24

Chapter 4 Other Functions...................................................................25

Copying Patches ....................................................................................................................................... 25
Exchanging Patches.................................................................................................................................. 25
Changing the function of the foot pedals (SW MODE) ...................................................................... 26
Switch Mode 1 ............................................................................................................................... 26
Switch Mode 2 ............................................................................................................................... 26
Saving Patches and System Parameter Settings on an External Device (BULK DUMP) ............... 26
Loading Patches and System Parameter Settings From an External Device (BULK LOAD)................ 27

Chapter 5 Connecting an External Sound Module or Sequencer..............28

Connecting an External Sound Module or Sequencer ........................................................................ 28
Setting the Transmission Mode................................................................................................... 28
Setting the MIDI Channel (BASIC CHANNEL) ....................................................................... 29
Specifying the Bend Range .......................................................................................................... 29
MIDI Messages Transmitted by the GR-20 ............................................................................... 29
Local Control Off ...................................................................................................................................... 30

Chapter 6 Appendices ..........................................................................31

Restoring the Factory Settings (Factory Reset)..................................................................................... 31
Calibrating the Expression Pedal ........................................................................................................... 31
Regarding GR-20 bass guitar support ................................................................................................... 32
Switching the GR-20 between bass guitar and guitar operation............................................ 32
How the Bass Guitar and Guitar settings differ ....................................................................... 32
Troubleshooting........................................................................................................................................ 33
During Normal Performance Using the GR-20 Alone............................................................. 33
When Using the GR-20 with other MIDI devices..................................................................... 33
Other ............................................................................................................................................... 34
Patch List.................................................................................................................................................... 35
User Patch List .......................................................................................................................................... 40
MIDI Implementation .............................................................................................................................. 41
MIDI Implementation Chart ................................................................................................................... 48
Main Specifications .................................................................................................................................. 49
INDEX ........................................................................................................................................................ 50

7
 Names of Things and What They Do

Front Panel
fig.0-01 (Panel Descriptions1)

1. BANK indicators 5. GK SIGNAL indicator

These indicators light to indicate the currently selected This indicator lights when a signal is received from the
sound bank. If the bank has been switched from an divided pickup.
external device (such as via MIDI or by the switches of
your GK pickup), the indicator for the selected bank 6. [GK SENS] button
will light regardless of the position of the BANK knob.
Press this button when you want to adjust the
sensitivity to match the output of the divided pickup.
2. [BANK] knob The system may malfunction if this adjustment is not
Selects the sound bank. The banks are organized into made correctly. Please adjust this setting accurately to
ten categories of sound. Sounds you edit can be stored match your guitar (p. 12).
in the User bank (p. 24).
7. OUTPUT/FREQ indicator
3. Display This indicator lights when you edit the System
Indicates the currently selected sound number. When parameter OUTPUT Select or the Patch parameter
you’re editing a parameter, the display indicates the FREQ (p. 14, p. 21).
value.
If you’ve edited the sound, the dot will light (p. 20). 8. SW MODE/RESO indicator
This indicator lights when you edit the System
4. [NUMBER/VALUE] knob parameter SW MODE or the Patch parameter RESO (p.
Use this to select the number of the sound you want to 14, p. 21).
play. Use the [BANK] knob (2) to select a category of
sounds, and use this knob to select a sound within that
category.
This knob is also used to change the values of other
parameters.

8
 Names of Things and What They Do

9. PATCH LINK SETUP/TRANSPOSE 21. [EXP PEDAL] button

indicator Press this button to select the function of the expression
This indicator lights when you edit the System pedal (p. 23).
parameter PATCH LINK SETUP or the Patch
parameter TRANSPOSE (p. 19, p. 21). 22. [GLIDE TYPE] button
Press this button to select the function of the Glide
10. MIDI CH/PLAY FEEL indicator pedal (p. 22).
This indicator lights when you edit the System
parameter MIDI CH or the Patch parameter PLAY 23. [HOLD TYPE] button
FEEL (p. 18, p. 21). Press this button to select the function of the Hold
pedal (p. 23).
11. [SYSTEM EDIT] button
Press this when you want to edit System parameters (p. 24. GLIDE pedal
14, p. 18, p. 19, p. 26, p. 27). Press this pedal to apply the Glide effect to the sound
(p. 15).
12. [PATCH EDIT] button
Press this when you want to edit Patch parameters (p. 25. GLIDE indicator
21). This indicator will light or blink according to how you
operate the GLIDE pedal.
13. [ATTACK] knob
Adjusts the speed of the attack (p. 20). 26. HOLD pedal
Press this pedal to apply the Hold effect to the sound
14. [RELEASE] knob (p. 16).
Adjusts the length of the release (p. 20).
27. HOLD indicator
15. [CHORUS] knob This indicator will light or blink according to how you
Adjusts the chorus depth (p. 20). operate the HOLD pedal.

16. [DELAY/REVERB] knob 28. Expression pedal

Adjusts the delay or reverb depth (p. 20). Use this pedal to adjust the volume or to apply
continuous change to the sound (p. 16).
17. [LEVEL] knob
Adjusts the volume of the synth sound for each patch
(p. 20). When you operate the expression pedal, please be
careful not to get your fingers pinched between the
movable part and the panel.
18. [EXIT] button
Press this to cancel an operation, or to return to a
previous state.
In households with small children, an adult should
provide supervision until the child is capable of
19. [WRITE] button following all the rules essential for the safe operation of
Press this button to write (store) or copy a patch (p. 24, the unit.
p. 25).

20. [TUNER] button

Press this button when you want to use the Tuner
function (p. 13).

9
 Names of Things and What They Do

Rear Panel
fig.0-02 (Panel Descriptions2)

29. GK IN connector * This is available only if the output of your guitar is

connected to the normal pickup input jack of the divided
Use the included GK cable (or GKC-3/5/10 (sold
pickup.
separately) to connect this connector to your divided
pickup.
33. [OUTPUT LEVEL] knob
* For details on connections to a commercially available GK-
compatible guitar, refer to the guitar manufacturer or your Adjusts the volume that is sent from the output jacks.
dealer.
34. MIDI IN/OUT connectors
30. GUITAR OUT jack These can be connected to external MIDI devices,
This jack outputs the sound from the normal pickup of allowing the GR-20 to send and receive MIDI data.
your guitar. Connect this jack to your guitar amp or
guitar effects unit. 35. [POWER] switch
Turns the power on/off.
31. MIX IN R (MONO)/L jacks
The sound that is input to these jacks is mixed with the 36. AC Adaptor jack
synth sound of the GR-20 and sent from the OUTPUT Connect the included AC adaptor (BRC-series) here.
jacks (32).
If you have connected the GUITAR OUT jack (30) to an
external effects unit, connect the output of your effects Use only the attached power-supply cord. Also, the
unit to this jack; the synth sound and the sound supplied power cord must not be used with any other
processed by the effects unit will be output together device.
from the OUTPUT jacks (32) (p. 17).
37. Cable hook
32. OUTPUT R (MONO)/L (PHONES) Loop the AC adaptor cable around this hook to prevent
jacks the cable from being accidentally disconnected.
These jacks output the GR-20’s synth sound combined
with the sound that is input to the MIX IN jacks (31). If
38. Security Slot ( )
you’re making connections to a monaural amp, use R
(MONO) jack. http://www.kensington.com/

The L (PHONES) jack can also be used as a headphone

jack (stereo). (However, if headphones are connected to
L (PHONES) jack, you cannot simultaneously use R
(MONO) jack as an output.)
If nothing is connected to the GUITAR OUT jack (30) or
MIX IN jacks (31), the guitar’s normal pickup sound
will also be mixed into this output.

10
 Chapter 1 Play the Sounds!

Preparing Your Guitar

• In order to use the GR-20 you will need a guitar that has
a divided pickup (GK pickup) such as the Roland GK-3
Various guitar manufacturers sell GK-Compatible guitars
or GK-2A, or a bass guitar that has a bass guitar divided
that have a pre-installed GK pickup or contain equivalent
pickup such as the Roland GK-3B/GK-2B, which can
functionality. For details, contact your guitar dealer or a
independently output a separate signal for each string.
guitar manufacturer.
• For details on installing the GK pickup, refer to the
manual that came with your GK pickup.
• Notes may be sounded incorrectly if there are string In order to use the GR-20 with a bass guitar, follow the
buzzes due to improper neck curvature or buzzing frets, procedure described in Chapter 6 Appendices “Switching
or if the octave adjustment (intonation) is incorrect. the GR-20 between bass guitar and guitar operation (p.
32)” to switch the GR-20 to bass guitar operation.

Connections
fig.1-01(Connection)

Stereo set, Synthesizer amp (keyboard amplifier, PA system, etc.)

radio-cassette player, etc.

To AUX, LINE IN

L R Guitar amp /
guitar effects processors
L R

Stereo headphones
The (L) MIX OUT jacks
can also be used as dual
stereo headphone jacks.
Also be aware that you
cannot simultaneously Guitar with GK-3 / GK-2A /
use one jack as a LINE other GK-Compatible guitar
OUT while using the or
other as a headphone Bass guitar with GK-3B / GK-2B
jack – that is, you can't
use a monaural plug and
a stereo plug at the same
time.

AC adaptor
(BRC series)

* To prevent malfunction and/or damage to speakers or other * To prevent the inadvertent disruption of power to your unit
devices, always turn down the volume, and turn off the power (should the plug be pulled out accidentally), and to avoid
on all devices before making any connections applying undue stress to the AC adaptor jack, anchor the
* The volume of your amp should be raised only after you have power cord using the cord hook, as shown in the illustration.
fig.1-02(Cord Hook)
turned on the power of all your other equipment.
* If you’re outputting in monaural, connect the cable to the R
(MONO) OUTPUT jack.

11
 Chapter 1 Play the Sounds!

Turning the Power On Adjusting the Input

Once the connections have been completed, turn on power to
Sensitivity (GK SENS)
your various devices in the order specified. By turning on You’ll need to adjust the input sensitivity of each string
devices in the wrong order, you risk causing malfunction according to your picking strength and how the divided
and/or damage to speakers and other devices. pickup is installed.
1. If you've connected a device to MIX IN, turn on the
power of that device.
If this adjustment is not made correctly, the system won’t
2. Turn on the power of the GR-20.
work properly. You must perform this adjustment to ensure
that you’re taking full advantage of the GR-20’s capabilities.

After you’ve turned on the power, you’ll be ready to play * Once you make this adjustment, it’s stored within the GR-20;
when the panel indicators and the display reach the state you won’t need to make it again. However, you should perform
shown in the illustration. This state is called “Play mode.” the adjustment again after changing the strings or adjusting
the action of your guitar, or before using a different GK guitar.
* If you’re using a bass guitar, you can use the following table to
Before the GR-20 enters Play mode, it will indicate whether it convert the string names and indications you see in the display
is currently in guitar mode or bass guitar mode. while performing the procedure below.
• Guitar mode: “ ” 6th string → B string
5th string → E string (4th string on a conventional four-string bass)
• Bass guitar mode: “ ”
4th string → A string (3rd string on a conventional four-string bass)
* For details on how to switch between guitar mode and bass 3rd string → D string (2nd string on a conventional four-string bass)
guitar mode, refer to p. 32. 2nd string → G string (1st string on a conventional four-string bass)
* This unit is equipped with a protection circuit. A brief interval 1st string → C string
(a few seconds) after power up is required before the unit will
1. Press the [GK SENS] button.
operate normally.
fig.1-03(Play Mode) 2. Play only the 6th string.
The left side of the display will show “6,” indicating that
you played the 6th string.
The right digit will show the GK SENS setting. The
BANK indicators will function as a level meter and show
the strength of the guitar signal.
* If the left digit of the display does not show the number of the
3. Turn on the power of your amp.
string you played, press the HOLD pedal or GLIDE pedal
several times to make the desired string number appear.
fig.1-04(GK SENS)

Adjusting the Output Level Level Meter

Use the [OUTPUT LEVEL] knob on the rear panel to adjust

the output level of the GR-20.
Turning the knob toward the right (toward MAX) will
increase the volume. With the knob turned all the way to the
left (toward MIN), the volume will be zero.
* Normally, you should set this near the middle of the range.
fig.1-10(Level)

3. Adjust the sensitivity.

Turn the [NUMBER/VALUE] knob to adjust the sensitivity.
The sensitivity will increase as the number in the right of
the display increases. Adjust the sensitivity so that all of
the level meter indicators light briefly when you pick a
note strongly.

12
 Chapter 1 Play the Sounds!

* You can also use your GK pickup's UP/S2 button and 2. Use the [NUMBER/VALUE] knob to adjust the reference
DOWN/S1 button to adjust the sensitivity in the same way. pitch.
If you turn the [NUMBER/VALUE] knob slightly, the
4. Perform steps 2–3 for strings 5–1 to adjust the sensitivity
current reference pitch will be displayed for several
of all strings.
seconds. By turning the [NUMBER/VALUE] knob
5. Press the [GK SENS] button or [EXIT] button. during this time, you can adjust the reference pitch.
The GK SENS settings you made are stored in the GR- * You can adjust the reference pitch in a range of 427 Hz–452 Hz.
20k, and you will return to Play mode. When the GR-20 is shipped from the factory, this is set to
* The decimal point in the display will blink while the setting is 440 Hz.
being stored. Don't turn off the power during this time. * The reference pitch you specify will be stored when you exit the
* If you turn off the power before returning to Play mode, the Tuner function. Be aware that the setting will not be stored if
settings you made will not be stored. you turn off the power before doing so.
3. Cleanly play an unfretted note on the string that you
want to tune.
If you’re using a bass guitar, the number shown at the left The display will indicate the note name.
fig.1-051
side of the display will be as shown in the following table.
C F#
Displayed No. 1 2 3 4 5 6
4-string 1G 2D 3A 4E
bass string string string string C# G

5-string 1G 2D 3A 4E 5B
bass string string string string string D G#
6-string 1C 2G 3D 4A 5E 6B
bass string string string string string string D# A

Tuning Your Guitar E A#

(Tuner Function) F B

Since the GR-20 analyzes the pitch of each string in order to

4. Tune your guitar.
determine the sound it should produce, you must tune your
Watch the indicator in the panel, and tune your guitar so
guitar accurately.
that only the green indicator in the middle is lit.
* If your guitar is mistuned, the sound produced will be out of fig.1-06(Tuning)
tune, and the system will not operate correctly.
1. Press the [TUNER] button.
The [TUNER] button will light, and the Tuner function
will be on. The lower two digits of the current reference
pitch will be shown for approximately two seconds in
the display. Then you will be able to tune your guitar.
Example: When the pitch is set to 440Hz
fig.1-05(Reference pitch)

too low too high

5. Repeat steps 3–4 to tune each string of your guitar.

6. Press the [TUNER] or [EXIT] button to exit the Tuner

function.
The reference pitch you specified will be stored, and you
will return to Play mode.
* The decimal point in the display will blink while the reference
pitch is being stored. Don't turn off the power during this
* You can also turn on the Tuner function by pressing the
time.
HOLD pedal and GLIDE pedal simultaneously.

13
 Chapter 1 Play the Sounds!

Specifying the Output Device Selecting a Sound (Patch)

(OUTPUT SELECT)
Here you can specify the type of system connected to the
What is a Patch
OUTPUT jacks. This setting allows the GR-20 to internally
optimize its sound for the type of playback system you are A “patch” is a sound you play on the GR-20; in addition to
using. the type of sound, a patch also contains settings for effects
* This does not affect the sound that is input to MIX IN. such as reverb and chorus.
The GR-20’s patches are organized into ten banks by type,
1. Press the [SYSTEM EDIT] button a number of times until
with the patches numbered within each bank.
the OUTPUT/FREQ indicator lights.
fig.1-07(OUTPUT SELECT)
In Play mode, the BANK indicator and the display show the
patch that is currently selected.
You can edit the settings of a patch to your taste, and store
edited patches in the USER bank (p. 24).
You can use any of the following ways to select a patch.

Using the Knob to Select Patches

1. Use the [BANK] knob to select the type of sound you
want.
From the ten sound banks and the user bank, select the
2. Use the [NUMBER/VALUE] knob to change the setting. bank that contains the sound you want to use.
Guitar amp
fig.1-071
2. Use the [NUMBER/VALUE] knob to select a sound
within the bank.
Turning the [NUMBER/VALUE] knob will change the
Use this setting if you’ve connected the GR-20 to a guitar number shown in the display, letting you choose from
amp. various sounds within the selected bank.
fig.1-08(Sound Select)

Line
fig.1-072

Use this setting if you’ve connected the GR-20 to a

keyboard amp, mixer, headphones, or recorder.
* If you’re using a bass amp, use the Line setting.

3. Press the [EXIT] button.

The setting will be stored, and you will return to Play
mode.
* The decimal point in the display will blink while the setting is
being stored. Don't turn off the power during this time.
* If you turn off the power before returning to Play mode, the
setting you made will not be stored.

14
 Chapter 1 Play the Sounds!

Using the Switches of the GK Play the GR-20!

Pickup to Select Patches
Let’s get started playing the GR-20. Check the following
In Play mode, you can use the UP/S2 button and DOWN/S1 points.
button of the GK pickup to select the next or previous
number. 1. Make sure that the GR-20 is in Play mode (the state it’s
normally in immediately following power up).
When you reach the upper or lower limit within a bank, you
will move to the next bank. In some cases, you won’t hear any sound if the GR-20 is
fig.1-09(S1/S2) not in Play mode.

2. Set the select switch of your GK pickup to the “GK”

position (on the GK-2A, the “SYNTH” position).
If this switch is set to “GUITAR,” the normal pickup
sound will be output. If this switch is set to “MIX,” the
synth sound and the guitar normal pickup sound will be
mixed and output.

3. Turn the volume of the GK pickup to the right.

This volume controls the synth sounds of the GR-20.
Using the Foot Pedals to Select fig.1-11(GK-3)

Patches
When shipped from the factory, the GR-20’s two foot pedals
are assigned to the Hold function and Glide (Pitch Bend)
function respectively. You can change these assignments so
that the foot pedals will select patches.
For details, refer to Changing the function of the foot
pedals (SW MODE) (p. 26).

Using an External Device Via Using the Foot Pedal to

MIDI to Select Patches Change the Pitch (GLIDE)
You can connect an external device (e.g., multi-effects unit) to
You can press the GLIDE pedal to change the pitch of the
the MIDI IN connector, and select patches on the GR-20 by
currently playing synth sound smoothly.
operating the external MIDI device.
The type of change will depend on the sound, and you can
For details, refer to Using the GR-20 with a Multi-effects
also adjust the change to your taste (p. 22).
Unit (p. 18). fig.1-12(GLIDE)

* The GLIDE indicator will blink while you are pressing the
pedal.

15
 Chapter 1 Play the Sounds!

Using the Foot Pedal to Turning the Power Off

Sustain the Sound (HOLD) When you’re ready to turn off the power, be sure to do so in
the following order.
You can press the HOLD pedal to sustain the synth sound
you're playing. The effect will depend on the sound, and you 1. Turn off the power of your amp.
can also adjust the effect to your taste (p. 23).
fig.1-13(HOLD)
2. Turn off the power of the GR-20.

3. Turn off the power of the device connected to MIX IN.

* The HOLD indicator will blink while you are pressing the
pedal.

Using the Expression Pedal

to Modify the Sound
(EXP PEDAL)
You can use the expression pedal to continuously vary the
volume or tone of the synth sound.
The effect will depend on the sound, and you can also adjust
the effect to your taste (p. 23).
fig.1-14(EXP)

16
 Chapter 2 Using the GR-20 with Guitar Effects

Here’s how you can use your own effects unit and combine the sound of the guitar with the synth sound to create an even more
interesting range of possibilities.
The sound of the guitar’s normal pickups will pass through the GK cable and be output from the GR-20’s GUITAR OUT jack.
The sound that is processed by your effects unit can be connected to the GR-20’s MIX IN, and internally mixed with the GR-20’s
synth sound.
* Connect the output of your guitar to the normal pickup input jack of the GK pickup.

Connections
Using a compact effect device or a multi-effects unit that has no MIDI connector
fig.2-01(Effect Connection 1)
Guitar amp

* Set the GR-20's OUTPUT SELECT

to “Guitar Amp” (p. 14).

Using a multi-effects unit that has a MIDI connector

fig.2-02(Effect Connection 2)

Keyboard amplifier, PA system, etc.

* If you're using a multi-effects unit, set
the GR-20 as follows:
Guitar Amp Simulation: on
Output Select: line

* Set the GR-20's OUTPUT SELECT to “Line” (p. 14).

* If your multi-effects device does not have a amp simulator, set the GR-20's OUTPUT SELECT to “Guitar Amp,” and connect the output
to a guitar amp.

17
 Chapter 2 Using the GR-20 with Guitar Effects

Switching between the Synth Using the GR-20 with a

Sound and Guitar Sound Multi-effects Unit
To switch between the synth sound and guitar sound, use the By connecting your multi-effects unit via MIDI, you can
selector switch provided on your GK pickup. automatically change sounds (patches) on the GR-20 by
f
selecting sounds (patches) on your multi-effects unit.

Channel (CH)
MIDI uses “channels” to send independent streams of data
over a single cable. In order for data to be received, the
receiving device must be set to receive the channel that the
transmitting device is sending on. This means you must set
the transmit channel of your multi-effects unit to match the
If the selector of your GK pickup (e.g., GK-3, GK-2A) is set to
receive channel of the GR-20.
the GK position (labeled SYNTH on the GK-2A), the synth
sound will be output. If set to the GUITAR position, the 1. Check the MIDI transmit channel of your multi-effects
guitar sound will be output. If the selector is set to MIX, both unit.
sounds will be mixed and output. For details, refer to the manual of your multi-effects unit.
* To adjust the volume balance between the synth sound and 2. Press the [SYSTEM EDIT] button a number of times until
guitar sound, use the volume (p. 20) of each patch to adjust the the MIDI CH/PLAY FEEL indicator lights.
synth sound, and the volume of the guitar or the connected fig.2-03(MIDI CH)

effects device to adjust the volume of the guitar sound.

3. Use the [NUMBER/VALUE] knob to change the setting.

Set the channel so it’s the same as the MIDI transmit
channel of your multi-effects unit.

4. Press the [EXIT] button.

The setting will be stored, and you will return to Play
mode.
* The decimal point in the display will blink while the setting is
being stored. Don't turn off the power during this time.
* If you turn off the power before returning to Play mode, the
setting you made will not be stored.

18
 Chapter 2 Using the GR-20 with Guitar Effects

Patch Link Setup

(PATCH LINK SETUP)
Here’s how to link the patches (sounds) of your multi-effects
unit with the patches (sounds) of the GR-20. This will cause
the GR-20 to automatically switch to the specified sound
(patch) when you change patches on your multi-effects unit.

1. Use a MIDI cable to connect the MIDI OUT of your

multi-effects unit to the GR-20's MIDI IN.

2. Make sure that the MIDI transmit channel of your multi-

effects unit is the same as the MIDI channel of the GR-20
(p. 18).

3. Press the [SYSTEM EDIT] button a number of times until

the PATCH LINK SETUP/TRANSPOSE indicator lights.
fig.2-04(PATCH LINK)

4. On your multi-effects unit, select the patch for which you

want to specify a link.
* When you select a patch on your multi-effects unit, it will send
a “MIDI Program Change” message to the GR-20. The GR-20
will remember the content of this message, and will be ready
for you to specify the patch link setting.
* If two or more consecutive patch changes occur when you are
selecting a patch on your multi-effects unit, the GR-20 will
remember only the last-received MIDI program change.

5. Use the [BANK] knob and [NUMBER/VALUE] knob to

select the synth sound in the GR-20 that you want to use
with the effect you chose in step 4.

6. Repeat steps 4–5 to set as many links as you need.

7. Press the [EXIT] button.

You will return to Play mode, and the settings you made
will be stored.
* The decimal point in the display will blink while the setting is
being stored. Don't turn off the power during this time.
* If you turn off the power before returning to Play mode, your
settings will not be stored.

19
 Chapter 3 Editing The Sounds

The GR-20 lets you modify the sound to your taste. This With the knob turned all the way to the left, it activates the
process is called “editing.” envelope follower function.
When you edit the settings, the decimal point in the display
Envelope Follower (E FLW) function
will light, indicating that the sound has been modified from
the original settings. The guitar synth analyzes the vibration of your guitar string
to detect the pitch, and then plays the appropriate synth
sound. This means that if the string vibration is less than a
Selecting a Sound to Start From certain level, it will not be possible to detect the pitch, and
the synth sound will be silenced at that point. For some
Use the [BANK] knob and [NUMBER/VALUE] knob to
patches, the way in which the sound is silenced at this time
select the sound (patch) from which you want to start editing
may produce an unnatural result.
(p. 14).
The envelope follower function causes the volume of the
synth sound to always follow the string vibration of the
Use the Knobs to Adjust the guitar, making the synth sound decay naturally along with
Sound the decay of the string vibration.

fig.3-01(knob)
* For some patches, the effect may be slight.
* Using the envelope follower function on a decay-type synth
sound such as piano or guitar may have the opposite effect,
producing an unnatural-sounding decay.

Adjusting the Spaciousness of the

Sound—CHORUS
This adjusts the depth of the chorus effect, which gives the
sound a spacious feel. Turning the knob toward the right will
deepen the effect, and turning it toward the left will lessen
* Immediately after a patch change, the sound you'll hear will the effect.
reflect the settings stored in the patch, regardless of the * You will hear the original sound when the knob is at the center
positions of the knobs. position.
* For some sounds, moving the knob may not make any
Adjusting the Attack—ATTACK difference.
This adjusts the attack time of the sound. Turning the knob
toward the right will lengthen the time, producing a more Adjusting the Reverberation
gradual attack. Turning the knob toward the left will shorten
—DELAY/REVERB
the time, producing a sharper attack.
This controls two types of reverberation effect.
* You will hear the original sound when the knob is at the center
Delay is an effect that produces echo-like effects, while
position.
Reverb is an effect that simulates the way in which sound
* For some sounds, moving the knob may not make any reflects from the walls of a hall or tunnel. The left half of the
difference. knob’s range applies a delay effect, and the right half applies
reverb. In either case, turning the knob farther will deepen
Adjusting the Release—RELEASE the effect.
This adjusts the release, from when you mute a string until it
decays to silence. Turning the knob toward the right will Adjusting the Volume—LEVEL
lengthen the release, and turning it toward the left will This adjusts the volume of the patch.
shorten the release.
* You will hear the original sound when the knob is at the center
position.
* If you want to keep your edited sound, execute Write (p. 24) to
* For some sounds, moving the knob may not make any write your settings into a USER patch.
difference.

20
 Chapter 3 Editing The Sounds

Editing Other Parameters Adjusting the Playing Feel

—PLAY FEEL
You will use the [PATCH EDIT] button and [NUMBER/
VALUE] knob to edit these parameters. You can select the way in which the synth sound will
respond to your picking dynamics. You can more naturally
1. Press the [PATCH EDIT] button a number of times until express your playing dynamics by changing this setting to
the indicator of the parameter you want to edit is lit. suit a particular playing style or sound.
2. Use the [NUMBER/VALUE] knob to edit the value. 1–4:
fig.3-02(Other Parameters)
The “1” setting gives you the widest range of
volume change in response to your picking
dynamics. With higher-numbered settings,
even softly picked notes will sound at a high
volume, making the volume more consistent
even when you use tapping techniques or if
your picking is not consistent.
No dynamics:
With this setting, notes will be sounded at a
fixed volume regardless of your picking
dynamics.
Strum:
Adjusting the Brightness of the
This setting suppresses softly picked notes.
Sound—FREQ
Use this setting if unwanted notes are
This controls the cutoff frequency of the filter within the triggered when you strum or when your finger
sound generator. contacts a string unintentionally.
Increasing this setting will raise the frequency, producing a
brighter tone. Conversely, decreasing this setting will lower
the frequency, producing a softer tone. 3. Press the [EXIT] button to return to Play mode.
* If you want to keep your edited sound, execute Write (p. 24) to
write your settings into a USER patch.
Adding a Distinctive Character to
the Tone—RESO
This controls the resonance of the filter within the sound
generator. Increasing this setting will produce a more
distinctive tone, while decreasing the setting will produce a
milder tone.

Adjusting the Pitch —TRANSPOSE

The pitch of the synth sound produced by the GR-20 can be
raised or lowered in one-octave steps relative to the pitch
you play on your guitar.
(-2, -1, 0, +1, +2)

21
 Chapter 3 Editing The Sounds

Selecting the Type of Glide u5–u8: GLIDE UP 5–8

Effect—GLIDE TYPE d5–d8: GLIDE DOWN 5–8

The pitch will change one octave (up/
You can select how the pitch changes when you press the down) when you press the GLIDE pedal,
and will return to normal when you re-
GLIDE pedal.
lease the pedal. Higher settings will short-
1. Press the [GLIDE TYPE] button. en the time over which the pitch changes.
fig.3-03(GLIDE TYPE)

V1–V4: VIBRATO 1–4

Pressing the pedal applies vibrato (an ef-
fect that changes the pitch cyclically). The
effect quickens as the value is increased
2. Use the [NUMBER/VALUE] knob to change the setting.

u1: GLIDE UP 1
d1: GLIDE DOWN 1
The pitch will change one semitone (up/
down) when you press the GLIDE pedal,
and will return to normal when you re- 3. Press the [GLIDE TYPE] button or [EXIT] button to
lease the pedal. return to Play mode.
* If you want to keep your edited sound, execute Write (p. 24) to
write your settings into a USER patch.
u2: GLIDE UP 2
d2: GLIDE DOWN 2
The pitch will change a whole step (up/
down) when you press the GLIDE pedal,
and will return to normal when you re-
lease the pedal.

u3: GLIDE UP 3
d3: GLIDE DOWN 3
The pitch will change a perfect fourth
(up/down) when you press the GLIDE
pedal, and will return to normal when you
release the pedal.

u4: GLIDE UP 4
d4: GLIDE DOWN 4
The pitch will change a perfect fifth (up/
down) when you press the GLIDE pedal,
and will return to normal when you re-
lease the pedal.

22
 Chapter 3 Editing The Sounds

Selecting the Type of Hold 3. Press the [HOLD TYPE] button or [EXIT] button to
return to Play mode.
Effect—HOLD TYPE
* If you want to keep your edited sound, execute Write (p. 24) to
You can select the type of hold effect you’ll get when you write your settings into a USER patch.
press the HOLD pedal.

1. Press the [HOLD TYPE] button.

fig.3-04(HOLD TYPE)
Selecting the Effect
Controlled by the Expression
Pedal—EXP PEDAL
You can select one of the following as the effect controlled by
the expression pedal.

1. Press the [EXP TYPE] button.

fig.3-05(EXP TYPE)

2. Use the [NUMBER/VALUE] knob to change the setting.

H1: HOLD 1
The notes that were sounding when you
pressed the pedal will be held, and any
notes you play while continuing to press
the pedal will also be held. However, if
you play any notes on a string that was al-
ready sounding, the previous note will
2. Use the [NUMBER/VALUE] knob to change the setting.
disappear and be replaced by the newly
played note. This lets you smoothly play
notes located at different fret positions. VO: VOLUME
The pedal will adjust the overall volume
H2: HOLD 2 of the synth sound.
The notes that were sounding when you
pressed the pedal will be held as long as
you continue pressing the pedal. Subse- FL: FILTER
quent notes that you play while holding The pedal will adjust the filter cutoff fre-
the pedal will not be heard. This lets you quency of the sound generator, varying
hold a chord using the synth sound, and the tone.
play a melody using the guitar sound.
b1: PITCH BEND 1
H3: HOLD 3
When the pedal is pressed, the pitch
The notes that were sounding when you changes up to a perfect fourth (max.).
pressed the pedal will be held as long as you
continue pressing the pedal. Subsequent
notes that you play while holding the pedal b2: PITCH BEND 2
will sound but will not be held. (The notes
When the pedal is pressed, the pitch
that you can play afterward are limited to
changes up to a perfect fifth (max.).
strings other than those that are being held.)
This lets you hold a chord using the synth
sound on the low notes, and play a melo-
dy on the high notes. b3: PITCH BEND 3
When the pedal is pressed, the pitch
H4: HOLD 4 changes up to one octave (max.).
The notes that were sounding when you
pressed the pedal will be held, and any subse-
quent notes you play while continuing to
press the pedal will also be held. This is the
same behavior as the damper pedal of a piano.

23
 Chapter 3 Editing The Sounds

b4: PITCH BEND 4 Storing the Sounds You

When the pedal is pressed, the pitch
changes down to a semi tone (max.).
Create (WRITE)
The sounds you create will be lost if you change the patch or
b5: PITCH BEND 5 simply turn off the power. If you want to keep the
When the pedal is pressed, the pitch modifications you’ve made, you must perform the Write
changes down to a whole tone (max.). procedure.

1. Press the [WRITE] button.

fig.3-06(WRITE)
b6: PITCH BEND 6
When the pedal is pressed, the pitch
changes down to one octave (max.).

EF: Effect
The pedal will adjust the effect used with-
in each patch.

* The result will differ for each patch.

* For some patches, there will be no effect.
The BANK indicators will indicate USER, and the
3. Press the [EXP TYPE] button or [EXIT] button to return display will blink.
to Play mode.
2. Use the [NUMBER/VALUE] knob to select the patch
* If you want to keep your edited sound, execute Write (p. 24) to number into which you want to write your settings.
write your settings into a USER patch.
* If you decide to abort the Write operation at this point, press
the [EXIT] button.

3. Press the [WRITE] button once again.

Your settings will be written into the patch you selected.
* Use caution, since the settings previously stored in that patch
will be overwritten and lost.
* The decimal point in the display will blink while the setting is
being stored. Don't turn off the power during this time.

24
 Chapter 4 Other Functions

Copying Patches Exchanging Patches

Here’s how you can copy patch settings. You can copy only Here’s how you can exchange (swap) patches within the
to the USER bank. USER bank. This is a convenient way to arrange USER bank
patches in the desired order.
1. Select the copy-source patch (the patch you want to copy
from). * This will not work if the selected patch is not in the USER
bank.
2. Press the [WRITE] button.
The BANK indicator will change to USER, and the 1. Select one of the patches that you want to exchange.
display will blink. 2. Hold down the [EXIT] button and press the [WRITE]
fig.4-01(COPY)
button.
The indication in the display starts blinking.
fig.4-02(EXCNG)

3. Use the [NUMBER/VALUE] knob to select the copy-

destination patch number (patch number you want to
copy to). 3. Use the [NUMBER/VALUE] knob to select the other
4. Press the [WRITE] button once again. patch that you want to exchange.
The setting will be copied to the copy-destination patch. 4. Press the [WRITE] button once again.
* The decimal point in the display will blink while copying the The patches will be exchanged.
setting. * The decimal point in the display will blink while the patches is
* Use caution, since the settings previously stored in the copy- being exchanged.
destination patch will be overwritten and lost.

25
 Chapter 4 Other Functions

Changing the function of the 2. Use the NUMBER/VALUE knob to change the setting.

foot pedals (SW MODE) * The actual mode of operation will not change until you store
the setting and return to Play mode.
You can change the function of the GLIDE pedal and the 3. Press the [EXIT] button.
HOLD pedal by changing the switch mode. This setting also
You will return to Play mode, and the setting will be
changes the function of your GK pickup's DOWN/S1 screen
stored.
and UP/S2 switch.
* The decimal point in the display will blink while the setting is
being stored. Don't turn off the power during this time.
Switch Mode 1 * The setting will not be stored if you turn off the power without
The GLIDE pedal operates the Glide function, and the HOLD returning to Play mode.
pedal operates the Hold function.
* In Switch Mode 1, the GLIDE indicator and HOLD indicator
Your GK pickup's UP/S2 switch and DOWN/S1 switch will will normally be lit; they will blink only while you press the
move up/down through the patches. pedal.
* This mode is selected when the GR-20 is shipped from the * In Switch Mode 2, the GLIDE indicator and HOLD indicator
factory. will normally be unlit; however, when the function of each
pedal is being changed by pressing the DOWN/S1 switch or

Switch Mode 2 UP/S2 switch, the indicators will behave the same way as they
do in Switch Mode 1.
The HOLD pedal and GLIDE pedal will move up/down
through the patches.
You can use your GK pickup's DOWN/S1 switch and UP/S1 Saving Patches and System
switch in conjunction with the pedals to perform the
following operations.
Parameter Settings on an
• When you press the DOWN/S1 switch, the GLIDE pedal External Device (BULK DUMP)
will function as Octave Down and the HOLD pedal will
Here’s how you can save the user bank patches and the
function as Octave Up (TRANSPOSE).
system parameter settings via MIDI on an external device or
When you press DOWN/S1 (or UP/S2) once again, the
computer (sequencer).
pedals will revert to the patch up/down function.
You can also transfer data via a MIDI cable directly between
• When you press the UP/S2 switch, the GLIDE pedal will
two GR-20 units.
function as Glide and the HOLD pedal will function as
Hold.
When you press UP/S2 (or DOWN/S1) once again, the Sending GR-20 data in this way is called “bulk dump,” and
pedals will revert to the patch up/down function. receiving this data is called “bulk load.”
1. Press the [SYSTEM EDIT] button enough times to get the
SW MODE indicator to light.
What are System Parameters?
Parameters that apply to the entire GR-20 (such as SW
MODE and MIDI CH) are called “system parameters.”

1. Connect the GR-20’s MIDI OUT to your external device’s

MIDI IN.

26
 Chapter 4 Other Functions

2. Turn off the power of the GR-20, and then hold down the
Loading Patches and System
[PATCH EDIT] button while you turn the power on
again. Parameter Settings From an
The display will indicate “dP.” External Device (BULK LOAD)
fig.4-03(DUMP)

Here’s how GR-20 settings saved via Bulk Dump on an

external device can be loaded back into the GR-20 via MIDI.

Performing the BULK LOAD operation will rewrite all the

data in the GR-20. Be aware that all currently existing data
will be lost.

1. Connect your external device’s MIDI OUT to the GR-20’s

MIDI IN.

3. Begin recording on the external device that will receive 2. Turn off the power of the GR-20, and then hold down the
the data. [PATCH EDIT] button and turn the power back on again.
If you want to transfer data between two GR-20 units, The display will indicate “dP.”
put the receiving GR-20 in the Bulk Load (p. 27) Ready
3. Using the [NUMBER/VALUE] knob, get “Ld” to appear
state.
in the display.
4. Press the [WRITE] button. fig.4-04(LOAD)

The data will be transmitted from MIDI OUT to the

external device.
During transmission, the display will show the following.
fig.4-031

4. Transmit the data from your external device.

Lit
When the display returns to “dP,” transmission has been During transmission, the display will show the
completed. following, and the decimal point of the display will
blink.
5. Stop recording on the receiving device. fig.4-041

6. Turn off the power.

When the decimal point of the display stops blinking,

and the display again shows “Ld,” reception has been
completed.

5. Press the [WRITE] button.

* If the power of the GR-20 was turned off while the data was
being received, the transmitted data will not be written into
the GR-20. If necessary, perform the Bulk Load operation once
again.

6. Press the [EXIT] button to return to Play mode.

27
 Chapter 5 Connecting an External Sound
Module or Sequencer

You can use the GR-20 to play an external sound module via Setting the Transmission Mode
MIDI, or use it as an input tool for your sequencer.
The GR-20 lets you select either “Mono Mode transmission”
or “Poly Mode transmission” as the method it uses when

Connecting an External transmitting MIDI messages.

Sound Module or Sequencer ❍Mono Mode transmission

Connect the GR-20 to your external sound module or Performance data for each string will be transmitted individually,
computer (sequencer) as shown in the diagram. with each using its own separate MIDI channel. Starting with the
fig.5-01(External Sound Module)
selected MIDI CH, six consecutive MIDI channels will be selected
automatically. For example, if MIDI CH is set to 3, the six channels
MIDI IN
3–8 will transmit MIDI data for strings 1–6, respectively.
Since continuous pitch change data (MIDI Pitch Bend messages)
can be transmitted independently for each string, this allows you
to use performance techniques typical of a guitar, such as use of
the whammy bar and string bending.

MIDI IN
* The connected sound module must be a multitimbral sound
module with at least six parts.

MIDI OUT ❍Poly Mode transmission

Performance data for all strings will be transmitted on a single
MIDI channel. The selected MIDI CH will be used. Since the
entire guitar will use only one channel, this lets you conserve
MIDI channels. This also lets you control a sound module that
is not able to receive six channels simultaneously.
* However, if two or more strings are sounding, bend data will
not be transmitted; pitch change will occur only in semitone
steps. This means that the pitch actually being played by the
fig.5-02(External Sequencer)
guitar will not be completely reflected by the synth sound.

1. Turn off the power of the GR-20, and hold down the
[EXIT] button while you turn the power on again.
fig.5-03(Transmission Mode)
MIDI
Interface
PC

MIDI IN MIDI OUT

2. Use the [NUMBER/VALUE] knob to select the mode.

: MONO MODE

* If you are connecting the GR-20 to a sequencer, turn “Local

Control Off” (p. 30). : POLY MODE

28
 Chapter 5 Connecting an External Sound Module or Sequencer

3. Press the [EXIT] button. MIDI Messages Transmitted by

The setting will be stored, and you will return to Play the GR-20
mode.
As performance data, the GR-20 transmits a note-on message
* The decimal point in the display will blink while the setting is
when you play a note, a note-off message when a note stops,
being stored. Don't turn off the power during this time.
and pitch bend messages when you bend a note.
* If you turn off the power before returning to Play mode, the In addition to these messages, the GR-20 also transmits the
setting you made will not be stored. following MIDI messages so that your performance can be
faithfully reproduced when recorded and played back by a

Setting the MIDI Channel sequencer.

(BASIC CHANNEL)
❍ENVELOPE FOLLOW
* You can select only channels 1–11. Channels 12–16 are not
If the RELEASE setting is E FLW (p. 20), MIDI control change
available.
number 18 (general purpose controller 3) will be transmitted
* If the output mode is set to “Mono Mode,” the GR-20 will use according to the amplitude of the guitar string’s vibration.
six channels starting with the channel you specify here.

1. Press the [SYSTEM EDIT] button a number of times until ❍GLIDE pedal
the MIDI CH/PLAY FEEL indicator lights.
MIDI pitch bend messages will be transmitted according to
fig.2-03(MIDI CH)
the change in pitch.

❍HOLD pedal
If the HOLD MODE is H1, H2, or H3
Outputting of MIDI note-off messages will be suspended as
long as you continue pressing the pedal.

If the HOLD MODE is H4

Control change number 64 will be transmitted.

2. Use the [NUMBER/VALUE] knob to change the setting. * In the case of Poly Mode transmission (p. 28), the Hold effect
cannot be conveyed entirely because it cannot be processed
Set the channel so it’s the same as the MIDI transmit
independently for identical pitches played on different strings.
channel of your multi-effects unit.

3. Press the [EXIT] button.

❍Expression pedal
The setting will be stored, and you will return to Play
Control change number 7 (Volume) or number 4 (Foot Type)
mode.
is transmitted according to movements of the pedal.
* The decimal point in the display will blink while the setting is
being stored. Don't turn off the power during this time.
❍Program change
* If you turn off the power before returning to Play mode, the
This message is transmitted when you switch patches.
setting you made will not be stored.
The sound bank is transmitted by MIDI Bank Select (CC#0),
and the sound number is transmitted as a Program Change
Specifying the Bend Range (PC).

Since the GR-20 transmits Pitch Bend data based on a bend

range of 24, you must set your sound module to a bend range
of ±24. For details on making this setting, refer to the manual
for your sound module.

29
 Chapter 5 Connecting an External Sound Module or Sequencer

Local Control Off * To turn Local Control on, turn the power of the GR-20 off,
then on again.
The state in which the GR-20’s guitar control section is
internally connected to the sound generator is referred to as
“Local Control On.” In contrast, the Local Control Off setting
internally disconnects the GR-20’s sound generator from the
guitar control section, so that the sound generator will produce
sound only in response to MIDI messages from MIDI IN. The
guitar performance will be transmitted only from MIDI OUT.
fig.5-033(Local Control Off)

Sequencer

Thru function to
MIDI OUT: On

MIDI OUT MIDI IN

MIDI IN MIDI OUT

Sound GK IN
Guitar
Generator Controller

Local Control
OFF

GR-20
By selecting the Local Control Off setting and enabling the
“Soft Thru” setting on your externally connected sequencer,
you can avoid conflicts from occurring between the
performance data from your guitar and from the sequencer.

1. Turn off the GR-20, and then hold down the [SYSTEM
EDIT] button while turning the power on again.
The display will indicate “Lo” for approximately one
second, and the GR-20 will then enter Play mode.
fig.5-04(Local Off)

* The Local Control Off setting cannot be stored.

* If the connections between the GR-20 and your external MIDI
device form a loop, you must use the Local Control Off setting.
If you make connections with this setting On, switches will
not function, and the system will not operate correctly.

30
 Chapter 6 Appendices

Restoring the Factory —

Settings (Factory Reset)
: Only the specified patch will be returned to the factory
If you want, you can get back all the settings and patches that
settings.
the GR-20 had when you first took it out of the box; this
process is called “Factory Reset.” 3. Press the [WRITE] button.
You can restore the entire GR-20 to the factory-set state, or The decimal point in the display will blink, the Factory
restore an individual user patch to its factory-set state. Reset operation will be executed. Then you will return to
Play mode.
* Do not turn off the power while the decimal point is blinking.
Calibration settings for the expression pedal (p. 31) will not
be returned to the factory-set condition. This means that even
if you execute Factory Reset, you don't need to calibrate the Calibrating the Expression
expression pedal again.
Pedal
When the GR-20 is shipped from the factory, the expression
When you execute Factory Reset, all data you currently have pedal is calibrated for optimum performance. However, with
stored in the unit will be overwritten by the factory-default extended use, or depending on the conditions of use, this
data. If the GR-20 contains important data that you want to calibration may drift. If you experience problems, such as
keep, use Bulk Dump (p. 26) to save it on an external MIDI being unable to use the volume pedal to silence the sound
device before you execute a Factory Reset. entirely, or if the pitch does not rise or fall through the full
range specified, you can use the following procedure to re-
1. Turn off the GR-20, and then hold down the [WRITE]
calibrate the expression pedal.
button while turning the power on again.
fig.6-01(FACTORY RESET 1Åj
1. Turn off the power of the GR-20. Then hold down [EXP
PEDAL] while you turn the power on again.
The display will indicate “Pu.”

2. Fully release the pedal (applying pressure at the heel),

and press the [WRITE] button.
The display will indicate “Pd.”

3. Depress the pedal completely (applying pressure at the

toe), and press the [WRITE] button.
The setting will be stored, and you will return to Play
mode.
2. Use the [NUMBER/VALUE] knob to select the range of
data that you want to restore to the factory settings. * The decimal point in the display will blink while the setting is
being stored. Don't turn off the power during this time.
* If you turn off the power before returning to Play mode, the
setting you made will not be stored.
: The entire GR-20 will be returned to the factory
settings.

When you perform this operation, the guitar/bass

setting will return to guitar mode (the default setting).
If you want to use the GR-20 with a bass guitar, you’ll
need to follow the procedure described in “Switching
the GR-20 between bass guitar and guitar operation
(p. 32)” to switch the GR-20 back to bass guitar mode.

31
 Chapter 6 Appendices

Regarding GR-20 bass guitar support

The GR-20 you purchased includes system program version 2, which allows the bass guitar range to be supported as well.
By connecting a bass guitar that has a separately sold GK-2B or GK-3B divided pickup (for bass) installed, you can play
the GR-20 from your bass guitar.
When shipped from the factory, the GR-20 is set for use with a guitar. The procedure described below lets you switch the GR-20 between
guitar and bass operation.
* You may repeat this procedure as many times as you like. Furthermore, this procedure will not affect the user patch data.

Switching the GR-20 between bass guitar and guitar operation ..........
1. Switch off the GR-20. Then while holding down the [GK SENS] button, turn on the power.
Shortly afterwards, the display will indicate “ ” or “ .”

2. Use the [NUMBER/VALUE] knob to select bass guitar or guitar operation.

• Bass guitar operation: Turn the [NUMBER/VALUE] knob toward the right (clockwise) to make the display read “ .”
• Guitar operation: Turn the [NUMBER/VALUE] knob toward the left (counterclockwise) to make the display read “ .”

3. Press the [EXIT] button.

The setting will be stored, and you will be in Play mode.
* The decimal point of the display will blink while the setting is being stored. Do not switch off the GR-20’s power while this takes place.
* Please note that the setting will not be stored if you neglect to return to Play mode before you switch off the unit.
* The setting is preserved until you repeat this procedure again.

How the Bass Guitar and Guitar settings differ ...................................

• The range of pitches produced by the GR-20 is switched between guitar and bass guitar ranges.

• In some of the preset patches, this setting causes the actual pitch produced by the synthesizer to be one or more octaves above or
below the pitch that is input. The same applies to user patches that you create based on these preset patches.
(Example) BANK= BASS/GTR No= “Wood Bass”

Bass Guitar operation The synthesizer will sound at the same pitch as the input.
Guitar operation The synthesizer will sound one octave lower than the input.

• When setting the input sensitivity (GK SENS), the numbers shown in the left of the display correspond to strings as shown in the
diagram below.

You must install the GK-2B/3B pickup on your bass guitar as shown below. The system will not operate correctly if you install
the pickup any other way.

For a four-string bass: For a five-string bass: For a six-string bass:

5th string 2nd string 5th string 2nd string 5th string 2nd string
marker marker marker marker marker marker
4 3 2 1
3 2 1 6 5 4 3 2 1

GK SENS Display

32
 Chapter 6 Appendices

Troubleshooting ● Internal effects not applied to the guitar sound

◆ The GR-20’s internal effects can only be applied to the

During Normal Performance synth sound. They cannot be applied to the normal guitar
Using the GR-20 Alone sound.
→ By using the guitar out jack you can apply an external
● Playing your guitar does not produce a synth sound guitar effects processor only to the guitar sound. (If you
want the synth sound and guitar sound to share a single
◆ Could the OUTPUT LEVEL have been lowered? amp, use the MIX IN jacks as well.) (p. 17)
→ Use the rear panel [OUTPUT LEVEL] knob to raise the
level appropriately (p. 12).
● The pitch of the synth sound does not change in the
◆ Could the volume of the GK pickup be turned down? same way as the pitch of the guitar
→ Raise the volume of the GK pickup to an appropriate
◆ The pitch of some tones (such as percussion instruments
level.
and sound effects) will change in a different way than the
◆ Could the select switch of the GK pickup be set to pitch of your guitar; it does not indicate a malfunction.
GUITAR?
→ Set the switch of the GK pickup to GK (or SYNTH) or ● You sometimes hear a thin, modulated noise in an
MIX. extremely high frequency range
◆ Could the expression pedal be released?
◆ This is a phenomenon known as “aliasing noise,” unique
→ Depress the expression pedal. to digital sound generators. You may hear this when
◆ Could the LEVEL be turned down? playing a slide or when using the glide function. This
does not indicate a malfunction.
→ Try turning the [LEVEL] knob (p. 20).

● The pitch changes in half-steps when bending or etc.

● Volume is uneven among the strings
◆ On some sounds (patches) such as piano or organ, the
◆ Was the “GK SENS” setting adjusted correctly for each
pitch will not change smoothly, but change only in
string?
semitone steps. This is done intentionally in order to
→ Perform the adjustment (p. 12). make the instrument sound more realistic; it does not
indicate a malfunction.

● When using Pitch Glide (or the pitch function of the

expression pedal), the pitch does not rise all the way ● Synth sound is delayed when you play from a bass

◆ Depending on the tone or the region of pitch, the range of

guitar

upward change may be restricted for functions that → The GR-20 analyzes the output of the divided pickups,
modify the pitch continuously. and produces the synth sound after the pitch and
→ Use a narrower range of change (p. 22, p. 23). loudness have been detected.
Due to the laws of physics, lower pitches take more time
to analyze. This means that with a bass guitar, and its
● When using the GR-20’s pedal effects or expression inherently lower pitches, you should expect that it may
pedal, the result is different for each patch take longer for the synth sound to begin.

◆ The effect produced using the expression pedal is

different for each sound (patch).
→ Check the effect of each patch beforehand.

33
Chapter 6 Appendices

When Using the GR-20 with ● When you view the note messages recorded in your
other MIDI devices sequencer, the pitches differ from what is actually
sounded

● The external sound module connected to the MIDI OUT ◆ In order to convey the beginning of a note as quickly as
connector does not sound possible, and to allow the pitch to change flexibly, the
GR-20 transmits the pitch as a combination of note
◆ Do the MIDI channels of the transmitting and receiving messages and pitch bend messages. This means that
devices match? when you view only the note data using the event list
→ Match the MIDI channels (p. 29). (“microscope”) screen of your sequencer, the data may
appear to be different than the pitch that is actually
◆ Could you have turned down the volume using the
sounded.
volume control of the GK pickup or the expression pedal?
→ Raise the controller or volume.
Other
● Only one string sounds on the external sound module
(some strings do not sound) ● The volume level of the instrument connected to MIX
IN jack is too low.
◆ Could you be using Mono mode to transmit from the GR-
20 to a sound module that is unable to receive six MIDI ◆ Could you be using a connection cable that contains a
channels simultaneously? resistor?
→ Use a sound module that supports multitimbral → Use a connection cable that does not contain a resistor.
operation (p. 28).
→ Use the GR-20 in Poly mode.

● Pitch is incorrect (different than the guitar pitch)

◆ Is the Bend Range of your external sound module set to

+-24?
→ Set the Bend Range of your external sound module to +-
24.

◆ Is your guitar tuned accurately?

→ Use the GR-20's Tuner function to tune your guitar
accurately. You must also adjust your guitar so that
accurate pitches are sounded even on the high frets.

● Pitch does not change smoothly

◆ On the GR-20, could you have selected a patch such as

piano or organ for which the pitch changes in semitone
steps?
→ Select a patch on the GR-20 whose pitch will change
smoothly.

34
 Chapter 6 Appendices

Patch List BANK No NAME

ORGAN/ 17 Glide Organ
KB 18 Cathedral
BANK No NAME 19 Church Choir
PIANO 1 Grand E.P 20 Rotary Choir Organ
2 Rock Piano 21 3 Tone Stack
3 Piano / Bass 22 Organ & Synth Strings
4 4-Hand Piano 23 Ice Organ
5 Honky Tonk 24 Clavi
6 Piano & Strings 25 Retro Clavi
7 Piano & Orchestra 26 Phase Clavi
8 Piano & Choir Oohs 27 JUNO Clavi
9 Piano & Choir Aahs 28 JUNO Keys
10 West Coast 29 Harpsichord
11 Ac.Piano 30 Baroque Piano
12 Hard Rhodes 31 Harpsichord & Strings
13 Rhodes 32 New Harpsichord
14 Phaser Rhodes 33 Accordion
15 Touch Sense E.P 34 Asian Trance
16 Soft Rhodes 35 Bell
17 Smooth Rhodes 36 Twinkle
18 Love E.P 37 Milky Way
19 E.P / Bass 38 D-50 Stack
20 Wide E.P 39 Dream Bell
21 Crystal Piano 1 40 Drama Stack
22 Crystal Piano 2 41 Staccato Heaven
23 Fantasy Piano 42 Heaven Choir
24 Silky E.P Pad 43 Hybrid Synth
25 Detuned E.P Pad 44 Archimedes
26 Chorus E.P Pad BASS/ 1 Wood Bass
27 E.P & Strings GTR 2 Wood Pick Bass
28 E.P & Choir 3 Electric Bass
29 Great Rhodes 4 Phased Bass
30 GR Ballad 5 Fretless Bass 1
31 Pulse E.P 6 Fretless Bass 2
32 Shattering 7 Slap Bass
33 Dynamic Piano 8 Touch Wah Slap Bass
34 Minor Mood 9 FM Bass
35 House 10 FM Bass + Low
ORGAN/ 1 Rock Organ 1 11 Flat Bass
KB 2 Rock Organ 2 12 Synth Bass
3 Rock Organ & Pedal Organ 13 2020 Bass
4 Rock Organ & Wood Bass 14 Soft Reso Bass
5 Rock Organ & E.Bass 15 101 Bass
6 Purple Organ 16 TB-303
7 Rock Organ 3 17 Acid TB
8 Jazz Organ 1 18 Wonder Bass
9 Jazz Organ 2 19 Res Bass 1
10 Jazz Organ & Pedal Organ 20 Res Bass 2
11 Jazz Organ & Wood Bass 21 Heavy
12 Jazz Organ & E.Bass 22 System Bass
13 Jazz Organ 3 23 Love Parade Bass
14 Jazz Organ 4 24 Mix Bass
15 Gospel Organ 25 MG Reso Bass
16 60’s Organ 26 Body Bass

35
Chapter 6 Appendices

BANK No NAME BANK No NAME

BASS/ 27 In Sync WIND 1 Fat Tenor Sax
GTR 28 Throw up 2 Bright Tenor Sax
29 Basstortion 3 Moody Sax
30 Nylon Guitar 4 Alto Sax
31 Nylon Duet 5 Alto Sax Vib
32 Nylon & Strings 6 Soprano Sax
33 Nylon & Choir 7 Baritone Sax
34 Ac.Guitar 8 Sax Ensemble
35 Ac.Guitar Oct 9 Sax Section & Baritone Sax
36 Ac.Guitar + Low 10 Brass Section & Baritone Sax
37 12 Str Guitar 11 Sax Section Oct
38 12 Str & Synth Strings 12 Harmonica
39 12 Str Heaven 13 Blues Harp OD
40 Guitar & Pad 14 Blues Harp Dist
41 Feedback 15 Piccolo
42 Whammy 16 Flute
43 OD-Paradise 17 Attack Flute
44 Small Amp Dist Vib 18 Piccolo & Glocken
45 Digital Rock Guitar 19 Flute & Glocken
46 Orgguitar 20 Piccolo & Flute
BRASS 1 Trumpet 21 Flute & Clarinet
2 Trumpet Split 22 Growl Flute
3 Mute Trumpet 23 Synth Flutes
4 Trombone 24 Playback Flute
5 Trombone Vib 25 Clarinet
6 Tuba 26 Clarinet Duet
7 Horn 27 Oboe
8 Flugelhorn 28 Bassoon
9 Tp Section 29 Oboe & Bassoon
10 Brass Section 30 Wind Ensemble Cresc.
11 NewYork Brass 31 Wind Ensemble
12 Brass & Sax 1 STRINGS 1 Strings
13 Brass & Sax 2 /ORCH 2 Hybrid Strings
14 French Horns 3 Dolce Strings
15 5th French Horns 4 Strings & Horns 1
16 French Heaven 5 Warm Strings
17 Pat Brass 6 Tremolo Strings
18 Brassy Saws 7 Strings Oct
19 Poly Brass 1 8 Strings & Timpani
20 Synth Brass 1 9 Nashville Strings
21 Xpensive Synth Brass 10 Good Old Strings Pad
22 Synth Brass 2 11 Silicon Strings
23 Synth Brass 3 12 Lo-Bows
24 Poly Brass 2 13 Marcato Strings
25 MG Brass 14 Pizzicato
26 Fat Synth Brass 15 Violin Vib
27 Breathy Brass 16 Violin
28 Lee Brass 17 Cello
29 Soft D-50 Brass 18 Cello Vib
30 Confident Lead 19 Synth Cello
31 Bright Synth Brass 20 Gang Strings
32 Brass It ! 21 Retro Synth Strings
33 Synth Brass Chord 22 Retro Synth Strings Oct
34 Wacky Brass 23 Playback Strings 1

36
 Chapter 6 Appendices

BANK No NAME BANK No NAME

STRINGS 24 Playback Strings 2 SYNTH/ 44 Haze Lead
/ORCH 25 Moving Strings LEAD 45 Vocoder
26 Clustered 46 Sweep Reso Lead
27 Farewell 47 Heavy Boost Lead
28 Wind & Strings 48 Morph
29 Orchestra & Choir 49 Sweep Lead
30 Ending Scene 50 Sync Sweep
31 Strings & Warm Brass 51 Vibro Sweep
32 Strings & Bright Brass 52 Rotary Lead
33 Strings & Horns 2 53 Step Saws
34 Synth Brass & Strings 54 Touch Filter
SYNTH/ 1 Guitar Attack Soft Lead 55 Trade Mark Lead
LEAD 2 Digi Lead 56 Retro Synth
3 Attack Digi Lead 57 No Bob No Hope
4 Creamer 58 House Of Phase
5 GR-300 Saw 1 59 Attack Organ Lead
6 Brass Lead 60 Minor Incid.
7 Simple Synth Lead 61 Heavy Oct Lead
8 Loud Synth Lead 62 Mental Chord
9 Synth Pad & Saws 63 House Chord 1
10 Heavy Saws Lead 64 House Chord 2
11 Saw & Square Lead 65 Flack
12 Poly Pulse 66 Waves
13 Daft Lead 67 Enterprise
14 Razor Lead 68 Chasing VOC
15 Blister Lead 69 Key In Sync
16 Sharp Attack Lead 70 Gated
17 Square Lead 1 71 Delay Gate
18 Square Lead 2 72 Acid Shuffle
19 Square Lead 3 73 Didgeridoo Dance
20 Reso Lead 1 74 Phobia
21 Square Lead 4 75 Deep
22 Basic 76 Atmosphere
23 OB Lead 77 Big Pipe Noise
24 Sine Lead 78 Sequencer
25 70’s Lead 79 Poly Key
26 SH-2000 80 Sandy Synth Attack
27 Simple Soft Lead 81 Detune Synth Attack
28 Soft Lead 1 82 For Synth Arpeggio
29 Soft Lead 2 83 Reso Synth Attack
30 Reso Lead 2 84 Trancy
31 Reso Lead 3 85 Fat Ana Lead 1
32 Saw Lead 1 86 Fat Ana Lead 2
33 Saw Lead 2 87 Wire Key
34 Bright Saw Lead 88 Pulse Key
35 Bright Moving Lead 89 Belly Keys
36 Saw Lead Vib 90 Velo Sense
37 Qwak Lead 91 Sugar Key
38 Flanger Ana Lead 92 Phobo Tron
39 Porta Wah 93 Sentimental
40 Wet Reso Lead VOICE/ 1 Jazz Doos
41 GR-300 Saw 2 PAD 2 Jazz Scat Bop
42 The Machine 3 Jazz Scat Doos & Bop
43 Big BPF 4 Male Aahs

37
Chapter 6 Appendices

BANK No NAME BANK No NAME

VOICE/ 5 Choir Aahs Soft ETHNIC 3 Sitar+Tampura
PAD 6 Choir Aahs 4 Sitar & Drone
7 Female Aahs 5 E.Sitar
8 Choir Oohs 6 Sitar & Tabla
9 Pop Chorus 7 Sitar & Tabla Phrase
10 Pop Voice 8 Sitar Pad
11 Arpeggio Choir 9 Banjo
12 Melancholia 10 5str Banjo
13 Spaced Voxx 11 Fiddle
14 Voice Pad 909 12 Flat Mandolin
15 Choir & Sweep 13 Flat Mandolin Tremolo
16 Wide Vox 14 Guitar & Morocco Phrase
17 Choir & Pad 1 15 Koto
18 Choir & Pad 2 16 Koto Heaven
19 Chorus Vox Pad 17 Shamisen
20 Heavenly Pad 18 Shamisen Ensemble
21 S&H Layer 19 Synth Shamisen
22 Wide Pad 20 Sanshin
23 Lost On Mars 21 Sanshin Soft
24 Miaow Pad 22 Kayakeum
25 JUNO Polaris 23 Erhu
26 Darkshine 1 24 Erhu Vib Soft
27 Darkshine 2 25 Erhu Vib Hard
28 Digi Saw Pad 26 Erhu & China Phrase
29 Analog Drama 1 27 Ocarina
30 Saws Sweep 1 28 Didgeridoo & Ocarina
31 Saws Sweep 2 29 India Flute
32 Xpensive Synth Pad 30 Andes
33 Wall of Sand 31 Pan Pipes
34 Super Bright Pad 1 32 Pan Pipes Soft
35 Super Bright Pad 2 33 Zampona Soft
36 Pivotal Pad 34 Zampona Hard
37 Pulsify 35 Shakuhachi
38 Vintage Orchestra 36 Shakuhachi & Drum Phrase
39 Cosmos Pad 37 Katmandu
40 Analog Drama 2 38 Legato Bamboo
41 Soft Pad Oct 39 Culture Flute
42 Soft Pad 40 Peru Lead
43 Pad / Bass 41 Mizmar
44 Silky Way 42 Mizmar Pad
45 JP-8 Haunting 43 Shanai
46 Shifted Glass 44 Dazin Shanai
47 Glass Voices 45 Gamelan Breathy
48 2.2 Warm Dream 46 Vox & Sitar & Tabla
49 Moving Fine Wine RHYTHM 1 Vibraphone
50 2.2 Bright Dream /PERC 2 Glockenspiel
51 Wine Pad 3 Xylophone
52 Glassy Pad 4 Marimba
53 Darkshine 3 5 Steel Drum
54 Soundtrack Seal 6 Timpani
55 Warm Pad 7 Impact
56 Changes 8 Orchestra Hit
ETHNIC 1 Sitar 9 Philly Hit
2 Sitar & Morocco Phrase 10 Kalimba

38
 Chapter 6 Appendices

BANK No NAME
RHYTHM 11 Agogo Bell
/PERC 12 Jublag
13 Gamelan Set
14 Kajar
15 Asian Gong
16 Finger Bell
17 Balaphone
18 Angklung
19 Dragon
20 Vox Set
21 Vox & Perc. Kit
22 Drum & Perc. Kit
23 Drum Kit
24 Machine & Perc. Kit
25 Machine Kit
26 Guiro & Cowbell Pattern
27 Latin Perc. Set
28 Conga Pattern
29 Tabla & Conga Set
30 Perc. & Morocco Phrase
31 Bell & Morocco Phrase
32 Vox & China Phrase
33 Cuica & Drum Phrase
34 Cuica & Samba Phrase
35 Steel Drum & Samba Phrase
36 Brass & Samba Phrase
37 Tambourine & Tabla Phrase
38 Synth Pulse & Tabla Phrase
39 Drum Kit Pattern 1
40 Drum Kit Pattern 2
41 Playmate
42 Delay Voice
43 Tribal Drums
44 Street Noise
45 FX Tom Hit
46 Perc. Heaven
47 Analog Snare
48 5th Gong
49 Back Noise
50 Oxygen

39
Chapter 6 Appendices

User Patch List No BANK BANK

No
NAME

72 ETHNIC 36 Shakuhachi & Drum Phrase

73 SYNTH/LEAD 53 Step Saws
No BANK BANK NAME 74 STRINGS/ORCH 32 Strings & Bright Brass
No 75 BRASS 32 Brass It !
1 BRASS 9 Tp Section 76 SYNTH/LEAD 20 Reso Lead 1
2 BASS/GTR 1 Wood Bass 77 SYNTH/LEAD 74 Phobia
3 PIANO 13 Rhodes 78 RHYTHM/PERC 3 Xylophone
4 WIND 1 Fat Tenor Sax 79 VOICE/PAD 39 Cosmos Pad
5 STRINGS/ORCH 1 Strings 80 SYNTH/LEAD 82 For Synth Arpeggio
6 ORGAN/KB 1 Rock Organ 1 81 PIANO 17 Smooth Rhodes
7 ETHNIC 2 Sitar & Morocco Phrase 82 BASS/GTR 23 Love Parade Bass
8 VOICE/PAD 8 Choir Oohs 83 WIND 27 Oboe
9 RHYTHM/PERC 5 Steel Drum 84 SYNTH/LEAD 71 Delay Gate
10 PIANO 1 Grand E.P 85 VOICE/PAD 6 Choir Aahs
11 BASS/GTR 6 Fretless Bass 2 86 RHYTHM/PERC 48 5th Gong
12 SYNTH/LEAD 5 GR-300 Saw 1 87 SYNTH/LEAD 13 Daft Lead
13 VOICE/PAD 51 Wine Pad 88 ORGAN/KB 7 Rock Organ 3
14 BRASS 3 Mute Trumpet 89 VOICE/PAD 33 Wall of Sand
15 WIND 15 Piccolo 90 SYNTH/LEAD 65 Flack
16 ORGAN/KB 25 Retro Clavi 91 BRASS 21 Xpensive Synth Brass
17 STRINGS/ORCH 7 Strings Oct 92 RHYTHM/PERC 12 Jublag
18 SYNTH/LEAD 48 Morph 93 SYNTH/LEAD 91 Sugar Key
19 RHYTHM/PERC 33 Cuica & Drum Phrase 94 ETHNIC 20 Sanshin
20 ETHNIC 17 Shamisen 95 VOICE/PAD 49 Moving Fine Wine
21 VOICE/PAD 10 Pop Voice 96 SYNTH/LEAD 1 Guitar Attack Soft Lead
22 PIANO 24 Silky E.P Pad 97 STRINGS/ORCH 3 Dolce Strings
23 WIND 4 Alto Sax 98 SYNTH/LEAD 41 GR-300 Saw 2
24 ORGAN/KB 6 Purple Organ 99 VOICE/PAD 20 Heavenly Pad
25 BASS/GTR 12 Synth Bass
26 ETHNIC 30 Andes
27 RHYTHM/PERC 1 Vibraphone
28 RHYTHM/PERC 8 Orchestra Hit
29 VOICE/PAD 45 JP-8 Haunting
30 ORGAN/KB 33 Accordion
31 ORGAN/KB 35 Bell
32 WIND 14 Blues Harp Dist
33 BASS/GTR 7 Slap Bass
34 PIANO 6 Piano & Strings
35 BRASS 17 Pat Brass
36 ORGAN/KB 18 Cathedral
37 RHYTHM/PERC 36 Brass & Samba Phrase
38 STRINGS/ORCH 15 Violin Vib
39 BASS/GTR 32 Nylon & Strings
40 BASS/GTR 19 Res Bass 1
41 ORGAN/KB 41 Staccato Heaven
42 ETHNIC 9 Banjo
43 VOICE/PAD 16 Wide Vox
44 BRASS 1 Trumpet
45 PIANO 27 E.P & Strings
46 SYNTH/LEAD 62 Mental Chord
47 WIND 10 Brass Section & Baritone Sax
48 BASS/GTR 37 12 Str Guitar
49 BRASS 26 Fat Synth Brass
50 ETHNIC 16 Koto Heaven
51 PIANO 35 House
52 VOICE/PAD 26 Darkshine 1
53 RHYTHM/PERC 46 Perc. Heaven
54 BRASS 11 NewYork Brass
55 WIND 7 Baritone Sax
56 ORGAN/KB 15 Gospel Organ
57 BRASS 14 French Horns
58 SYNTH/LEAD 37 Qwak Lead
59 STRINGS/ORCH 18 Cello Vib
60 ETHNIC 3 Sitar + Tampura
61 VOICE/PAD 3 Jazz Scat Doos & Bop
62 RHYTHM/PERC 19 Dragon
63 PIANO 10 West Coast
64 WIND 18 Piccolo & Glocken
65 SYNTH/LEAD 10 Heavy Saws Lead
66 STRINGS/ORCH 24 Playback Strings 2
67 RHYTHM/PERC 35 Steel Drum & Samba Phrase
68 ETHNIC 24 Erhu Vib Soft
69 ORGAN/KB 29 Harpsichord
70 SYNTH/LEAD 29 Soft Lead 2
71 ORGAN/KB 37 Milky Way

40
 MIDI Implementation
Model: GR-20 ❍Hold1
Date: Dec. 18 2003 STATUS SECOND THIRD
Version: 1.00 BnH 40H vvH

1. Recognized Receive Data n=MIDI Channel Number: 0H - BH (ch.1 - ch.12)

vv=Control Value: 00H - 7FH (0 - 127)
00H-3FH=OFF, 40H-7FH=ON
■Channel Voice Message
* Can be received only through the Basic channel.
●Note Off
STATUS SECOND THIRD ●Program Change
8nH kkH vvH STATUS SECOND
9nH kkH 00H CnH ppH

n=MIDI Channel Number: 0H - FH (ch.1 - ch.16) n=MIDI Channel Number: 0H - BH (ch.1 - ch.12)
kk=Note Number: 00H - 7FH (0 - 127) pp=Program Number: 00H - 7FH (0 - 127) 0=prg.1 127=prg.128
vv=Velocity: 00H - 7FH (0 - 127)
* Can be received only through the Basic channel.
* Velocity is ignored. * The recognized Program Change Number corresponds to each patch as follows.

●Note On BANK MSB PROGRAM NUMBER PATCH

STATUS SECOND THIRD 0 0 USER1
9nH kkH vvH 0 1 USER2
0 2 USER3
n=MIDI Channel Number: 0H - FH (ch.1 - ch.16) 0 3 USER4
kk=Note Number: 00H - 7FH (0 - 127) 0 : :
vv=Velocity: 01H - 7FH (1 - 127) 0 97 USER98
0 98 USER99
* vv=00H is received as Note-off
1 0 PIANO1
1 1 PIANO2
●Control Change 1 3 PIANO3
❍Bank Select : :
STATUS SECOND THIRD 2 0 ORGAN/KB1
BnH 00H mmH 2 1 ORGAN/KB2
2 3 ORGAN/KB3
n=MIDI Channel Number: 0H - BH (ch.1 - ch.12) : :
mm=Bank Number: 00H - 0AH 3 0 BASS/GTR1
3 1 BASS/GTR2
* The LSB of Bank Select is ignored. 3 3 BASS/GTR3
* Can be received only through the Basic channel. : :
4 0 BRASS1
❍Foot Type 4 1 BRASS2
STATUS SECOND THIRD 4 3 BRASS3
BnH 04H vvH : :
5 0 WIND1
n=MIDI Channel Number: 0H - BH (ch.1 - ch.12) 5 1 WIND2
vv=Control Value: 00H - 7FH (0 - 127) 5 3 WIND3
: :
* Can be received only through the Basic channel. 6 0 STRING/ORCH1
* Received when EXP PEDAL TYPE = “FL”, “EF”. 6 1 STRING/ORCH2
6 3 STRING/ORCH3
❍Volume : :
STATUS SECOND THIRD 7 0 SYNTH/LEAD1
BnH 07H vvH 7 1 SYNTH/LEAD2
7 3 SYNTH/LEAD3
n=MIDI Channel Number: 0H - BH (ch.1 - ch.12) : :
vv=Volume: 00H - 7FH (0 - 127) 8 0 VOICE/PAD1
8 1 VOICE/PAD2
* Can be received only through the Basic channel. 8 3 VOICE/PAD3
: :
❍General Purpose #3 9 0 ETHNIC1
STATUS SECOND THIRD 9 1 ETHNIC2
BnH 12H vvH 9 3 ETHNIC3
: :
n=MIDI Channel Number: 0H - FH (ch.1 - ch.16) 10 0 RYTHM/PERC1
vv=Control Value: 00H - 7FH (0 - 127) 10 1 RYTHM/PERC2
10 3 RYTHM/PERC3
* When E FLW is on, and recognized as the string envelope follow values. : :

41
 Chapter 6 Appendices

●Pitch Bend Change ■System Exclusive Message

STATUS SECOND THIRD
EnH llH mmH STATUS SECOND THIRD
F0H iiH ddH eeH F7H
n=MIDI Channel Number: 0H - FH (ch.1 - ch.16)
mm,ll=Value: 00H, 00H - 7FH, 7FH (-8192 - +8191) F0H: System Exclusive
ii = Manufacturer ID: 41H (65)
dd ......ee = Data: 00H - 7FH (0 - 127)
■Channel Mode Message F7H: EOX (End Of Exclusive)

* For more details, refer to the page of “Roland Exclusive message” and Section 3 or after.
●All Note Off
STATUS SECOND THIRD
BnH 7BH 00H

n=MIDI Channel Number: 0H - BH (ch.1 - ch.12) 2. Transmitted Data

* Can be received only through the Basic channel ■Channel voice messages
* Turn off all notes that are now on.

●Note Off
●OMNI OFF STATUS SECOND THIRD
9nH kkH 00H
STATUS SECOND THIRD
BnH 7CH 00H
n=MIDI channel Number: 0H - FH (ch.1 - ch.16)
kk=Note Number: 00H - 7FH (0 - 127)
n=MIDI Channel Number: 0H - BH (ch.1 - ch.12)

* Can be received only through the Basic channel. ●Note On

* Will act the same as All Note Off. STATUS SECOND THIRD
9nH kkH vvH

●OMNI ON n=MIDI Channel Number: 0H - FH (ch.1 - ch.16)

kk=Note Number: 00H - 7FH (0 - 127)
STATUS SECOND THIRD
vv=Velocity: 01H - 7FH (1 - 127)
BnH 7DH 00H

n=MIDI Channel Number: 0H - BH (ch.1 - ch.12) ●Control Change

* Can be received only through the Basic channel. ❍Bank Select

* Will act the same as All Note Off. STATUS SECOND THIRD
BnH 00H mmH
BnH 20H llH
●MONO
n=MIDI Channel Number: 0H - FH (ch.1 - ch.16)
STATUS SECOND THIRD
mm,ll=Bank Number: 00H, 00H - 0AH, 00H
BnH 7EH mmH

n=MIDI Channel Number: 0H - BH (ch.1 - ch.12) ❍Foot Type

mm=Number of Individual Channels: 00H - 10H (0 - 16) STATUS SECOND THIRD
BnH 04H vvH
* Can be received only through the Basic channel.
* Will act the same as All Note Off. n=MIDI Channel Number: 0H - BH (ch.1 - ch.12)
vv=Control Value: 00H - 7FH (0 - 127)

●POLY * When the Expression pedal is operated with EXP TYPE = “FL”, “EF”, the GR-20 sends
this as the operation.
STATUS SECOND THIRD
BnH 7FH 00H
❍Data Entry
STATUS SECOND THIRD
n=MIDI Channel Number: 0H - BH (ch.1 - ch.12)
BnH 06H mmH
BnH 26H llH
* Can be received only through the Basic channel.
* Will act the same as All Note Off.
n=MIDI Channel Number: 0H - FH (ch.1 - ch.16)
mm,ll=the value of the parameter specified by RPN

■System Realtime Message ❍Volume

STATUS SECOND THIRD
●Active Sensing BnH 07H vvH
STATUS
FEH n=MIDI Channel Number: 0H - FH (ch.1 - ch.16)
vv=Volume: 00H - 7FH (0 - 127)
* Having received this message, the GR-20 expects to receive information of any status of
data during about 420msec.If the GR-20 doesn’t receive any message during that time, it * Transmitted the total volume fixed with expression pedal and GK PU operation.
acts as if the All Note Off message is received, and returns to normal operation (will not
check interval of messages).

42
 Chapter 6 Appendices

❍General Purpose #3 : :
STATUS SECOND THIRD 6 0 STRING/ORCH 1
BnH 12H vvH 6 1 STRING/ORCH 2
6 2 STRING/ORCH 3
n=MIDI Channel Number: 0H - FH (ch.1 - ch.16) : :
vv=Control Value: 00H - 7FH (0 - 127) 7 0 SYNTH/LEAD 1
7 1 SYNTH/LEAD 2
* Transmitted the envelope data of the strings when “E FLW” is on. 7 2 SYNTH/LEAD 3
* Data is sent only in Mono mode. Transmission doesn’t take place in Poly mode. : :
8 0 VOICE/PAD 1
❍Hold1 8 1 VOICE/PAD 2
8 2 VOICE/PAD 3
STATUS SECOND THIRD
: :
BnH 40H vvH
9 0 ETHNIC 1
9 1 ETHNIC 2
n=MIDI Channel Number: 0H - FH (ch.1 - ch.16)
9 2 ETHNIC 3
vv=Control value: 00H - 7FH (0 - 127)
: :
01H-3FH=OFF, 40H-7FH=ON
10 0 RHYTHM/PERC 1
10 1 RHYTHM/PERC 2
* Transmitted the operation of HOLD TYPE = “H4”.
10 2 RHYTHM/PERC 3
: :
❍RPN MSB/LSB
STATUS SECOND THIRD
BnH 65H mmH
BnH 64H llH ●Pitch Bend Change
STATUS SECOND THIRD
n=MIDI Channel Number: 0H - FH (ch.1 - ch.16) EnH llH mmH
mm=Upper byte of the parameter data designated by RPN
ll=Lower byte of the parameter data designated by RPN n=MIDI Channel Number: 0H - FH (ch.1 - ch.16)
mm,ll=Value: 00H, 00H - 7FH, 7FH (-8192 - +8191)
<<< RPN >>>
Control change includes RPN(registered parameter number), function which are defined by
the MIDI standard. ■System Realtime Message
The GR-20 can transmit only one RPN: pitch bend sensitibity(RPN#0).

❍Active Sensing
RPN Data entry
STATUS
MSB LSB MSB LSB Function
FEH
00H 00H 18H 00H pitch bend sensitivity

* This message is always transmitted at about 270msec’ interval.

●Program change ❍System Exclusive message

STATUS SECOND
CnH ppH STATUS SECOND THIRD
F0H iiH,ddH,.....,eeH F7H
n=MIDI Channel Number: 0H - FH (ch.1 - ch.16)
pp=Program Number: 00H - 7FH (prg.1 - prg.128) F0H: System Exclusive
ii=ID Number: 41H (65)
* The recognized Program Change Number corresponds to each patch as follows. dd,...,ee=Data: 00H-7FH (0-127)
F7H: EOX (End of Exclusive/System Common
BANK MSB PROGRAM NUMBER PATCH Message)
0 0 USER 1
0 1 USER 2 * For more details, refer to the page “Roland exclusive message” and Section3 or after.
0 2 USER 3
0 3 USER 4
0 : :
0 97 USER 98 3. Exclusive Communications
0 98 USER 99
The GR-20 can transmit or receive system and patches parameters using system exclusive
1 0 PIANO 1 messages. Model ID of exclusive message available on the GR-20 is 00H 72H.Device ID is
1 1 PIANO 2 fixed at 10H.
1 2 PIANO 3 When the GR-20 receives an Identify Request inquiry message, it will transmit an Identity
: : Reply.
2 0 ORGAN/KB 1
2 1 ORGAN/KB 2
2 2 ORGAN/KB 3
: :
3 0 BASS/GTR 1
3 1 BASS/GTR 2
3 2 BASS/GTR 3
: :
4 0 BRASS 1
4 1 BRASS 2
4 2 BRASS 3
: :
5 0 WIND 1
5 1 WIND 2
5 2 WIND 3

43
 Chapter 6 Appendices

●Request Data1 RQ1 (11H)

Transmitted data:
THis message is to request the GR-20 to transmit its parameters.
The address and size indicate the type and amount of parameters requested. F0H 41H 10H 00H 72H 12H 01H 00H 00H 06H 5AH 32H 3CH 03H 2EH F7H
The GR-20 itself does not send this message. 1 2 3 4 5 6 7 8 9
When the GR-20 receives this message, it responds with appropriate parameters if the
following conditions are satisfied: 1. Exclusive status is F0H.
2. Roland’s Manufacturer ID is 41H.
1. The address indicated with RQ1 matches with one of the parameter base address of the 3. This is the device ID.(Fixed at 10H for GR-20)
GR-20 4. Model ID of the GR-20 is 00H 72H.
2. When the Bulk Load standby mode. 5. DT1 (Data Set1) Command ID is 12H.
6. These are the parameter addresses. Please find the start address of the USER BANK 01
With these conditions provided, the GR-20 transmits specified parameters in Data Set 1 Patch from the table of the start address.You can find the address as 01H 00H 00H 00H.
(DT1) message. Next, please find the offset address of the LEVEL Parameter from the table 4-2. That is
00H 00H 06H.The result will be 01H 00H 00H 06H.
Byte Comments
01H 00H 00H 00H (the start address of the USER patch)
F0H System Exclusive Status
+) 00H 00H 06H (the offset address of the LEVEL)
41H Manufacturer ID (Roland)
----------------------------
10H Device ID (Dev=10H)
01H 00H 00H 06H
00H Model ID MSB (GR-20)
72H Model ID LSB (GR-20)
7. The settings value for LEVEL is 90. This is expressed as 5AH in hexadecimal notation
11H Command ID (RQ1)
with two digits. (Refer to the attached Chart A-1)
aaH Address MSB
The settings value for FREQ is 115. This is expressed as 32H in hexadecimal notation with
bbH Address
two digits.
ccH Address
The settings value for RESO is 60. This is expressed as 3CH in hexadecimal notation with
ddH Address LSB
two digits.
ssH Size MSB
The settings value for TRANSPOSE is +1oct. This is expressed as 03H in hexadecimal
ssH Size
notation with two digits from Table 4-4.
ssH Size
ssH Size LSB
8. This is the check sum byte.The error checking process uses a Checksum and provides a
sum Check sum
pattern where the last significant 7 bits are zero when values for address, data(or size)
F7H EOX (End Of Exclusive)
and the Checksum are summed.
If the address of the exclusive message that you wish to send is aa bb cc ddH and the
data(or size) is ee ff hh iiH,
●Data Set 1: DT1 (12H)
aa + bb + cc + dd + ee + ff + hh + ii = sum
The GR-20 transmits this message in the following conditions. sum / 128 = quotient ...remainder
If the address matches with one of the parameter base addresses of the GR-20, the received 128 - remainder = checksum
data is stored at the specified address of the memory. * However, when sum=0, then the checksum also results in 0.

The GR-20 transmits this message in the following conditions. In case of this example,
When data request (RQ1) is received with the Bulk Load mode, and the specified
parameters are transmitted. F0H 41H 10H 00H 72H 12H 01H 00H 00H 06H 5AH 32H 3CH 03H ??H F7H
or you executes Bulk Dump function. address data checksum

Regarding details of the parameter transmitted/received, please refer to the Parameter Using the above formula, Checksum will be as follows.
Address Map.

01H + 00H + 00H + 06H + 5AH + 32H + 3CH + 03H = 1 + 0 + 0 + 6 + 90 + 50 + 60 + 3

Byte Comments = 210 (sum)
F0H System Exclusive Status 210 (sum) / 128 = 1 (quotient) ...82 (remainder)
41H Manufacturer ID (Roland) checksum = 128 - 82 (remainder) = 46 = 2EH
10H Device ID (Dev=10H)
00H Model ID MSB (GR-20) If you calculate with hexadecimal,
72H Model ID LSB (GR-20)
12H Command ID (DT1) aa + bb + cc + dd + ee + ff = sum (xxH)
aaH Address MSB sum (xxH) / 80H = quotient ...remainder
bbH Address 80H - remainder = checksum
ccH Address
ddH Address LSB Checksum will be as follows.
eeH Data
: : 01H + 00H + 00H + 06H + 5AH + 32H + 3CH + 03H = D2H
ffH Data D2H / 80H = 01H (quotient) ...52H (remainder)
sum Check Sum checksum = 80H - 52H (remainder) = 2EH
F7H EOX (End of Exclusive)

9. F7H is the mark of the end of exclusive.

Model ID The Model ID of the GR-20 is 00H 30H.
Device ID Device ID of the GR-20 is fixed at 10H.
/Example of creating the exclusive message/
If you want to set as the following the parameter LEVEL/FREQ/RESO TRANSPOSE of
USER BANK 01 Patch, create data as the following and send it to your GR-20.

Reverb setting:
LEVEL: 90
FREQ: 50
RESO: 60
TRANSPOSE: +1oct

44
 Chapter 6 Appendices

●Inquiry Message Start Address Contents and Remarks Table

01 00 1E 00 Patch USER 31 *4-4
01 00 1F 00 Patch USER 32 *4-4
❍Identity Request
01 00 20 00 Patch USER 33 *4-4
Byte Comments 01 00 21 00 Patch USER 34 *4-4
F0H Exclusive Status 01 00 22 00 Patch USER 35 *4-4
7EH ID number (Universal Non-realtime Message) 01 00 23 00 Patch USER 36 *4-4
10H Device ID 01 00 24 00 Patch USER 37 *4-4
06H SubID#1 01 00 25 00 Patch USER 38 *4-4
01H SubID#2 01 00 26 00 Patch USER 39 *4-4
01 00 27 00 Patch USER 40 *4-4
F7H EOX (End of Exclusive)
01 00 28 00 Patch USER 41 *4-4
01 00 29 00 Patch USER 42 *4-4
* The 7FH (Broadcast) device ID is also supported. 01 00 2A 00 Patch USER 43 *4-4
* Identity request can be received when Bulk Load is standby in System mode. 01 00 2B 00 Patch USER 44 *4-4
* When an Identity Request is received, the GR-20 will transmit the following Identity 01 00 2C 00 Patch USER 45 *4-4
Reply. 01 00 2D 00 Patch USER 46 *4-4
01 00 2E 00 Patch USER 47 *4-4
01 00 2F 00 Patch USER 48 *4-4
❍Identity Reply
01 00 30 00 Patch USER 49 *4-4
Byte Comments 01 00 31 00 Patch USER 50 *4-4
F0H Exclusive Status 01 00 32 00 Patch USER 51 *4-4
7EH ID number (Universal Non-realtime Message) 01 00 33 00 Patch USER 52 *4-4
10H Device ID (fixed at 10H) 01 00 34 00 Patch USER 53 *4-4
06H SubID#1 01 00 35 00 Patch USER 54 *4-4
02H SubID#2 01 00 36 00 Patch USER 55 *4-4
01 00 37 00 Patch USER 56 *4-4
41H ID number(Roland)
01 00 38 00 Patch USER 57 *4-4
72H 01H Device Family Code
01 00 39 00 Patch USER 58 *4-4
00H 00H Device Family Number Code 01 00 3A 00 Patch USER 59 *4-4
00H 00H 00H 00H Software Revision Level 01 00 3B 00 Patch USER 60 *4-4
F7H EOX (End of Exclusive) 01 00 3C 00 Patch USER 61 *4-4
01 00 3D 00 Patch USER 62 *4-4
* When an Identity Request is received, the GR-20 will transmit the above Identity Reply. 01 00 3E 00 Patch USER 63 *4-4
01 00 3F 00 Patch USER 64 *4-4
01 00 40 00 Patch USER 65 *4-4
01 00 41 00 Patch USER 66 *4-4
4. Parameter Address Map 01 00 42 00 Patch USER 67 *4-4
01 00 43 00 Patch USER 68 *4-4
01 00 44 00 Patch USER 69 *4-4
Addresses and sizes are expressed in 7-bit hexadecimal values.
01 00 45 00 Patch USER 70 *4-4
01 00 46 00 Patch USER 71 *4-4
Address MSB LSB 01 00 47 00 Patch USER 72 *4-4
Binary 0aaa aaaa 0bbb bbbb 0ccc cccc 0ddd dddd 01 00 48 00 Patch USER 73 *4-4
7 bit Hex AA BB CC DD 01 00 49 00 Patch USER 74 *4-4
01 00 4A 00 Patch USER 75 *4-4
Size MSB LSB 01 00 4B 00 Patch USER 76 *4-4
01 00 4C 00 Patch USER 77 *4-4
Binary 0sss ssss 0ttt tttt 0uuu uuuu 0vvv vvvv
01 00 4D 00 Patch USER 78 *4-4
7 bit Hex SS TT UU VV
01 00 4E 00 Patch USER 79 *4-4
01 00 4F 00 Patch USER 80 *4-4
Table 4-1. Start Address 01 00 50 00 Patch USER 81 *4-4
01 00 51 00 Patch USER 82 *4-4
Start Address Contents and Remarks Table 01 00 52 00 Patch USER 83 *4-4
00 00 00 00 System *4-2 01 00 53 00 Patch USER 84 *4-4
00 01 00 00 System Patch Link Map *4-3 01 00 54 00 Patch USER 85 *4-4
01 00 00 00 Patch USER 1 *4-4 01 00 55 00 Patch USER 86 *4-4
01 00 01 00 Patch USER 2 *4-4 01 00 56 00 Patch USER 87 *4-4
01 00 02 00 Patch USER 3 *4-4 01 00 57 00 Patch USER 88 *4-4
01 00 03 00 Patch USER 4 *4-4 01 00 58 00 Patch USER 89 *4-4
01 00 04 00 Patch USER 5 *4-4 01 00 59 00 Patch USER 90 *4-4
01 00 05 00 Patch USER 6 *4-4 01 00 5A 00 Patch USER 91 *4-4
01 00 06 00 Patch USER 7 *4-4 01 00 5B 00 Patch USER 92 *4-4
01 00 07 00 Patch USER 8 *4-4 01 00 5C 00 Patch USER 93 *4-4
01 00 08 00 Patch USER 9 *4-4 01 00 5D 00 Patch USER 94 *4-4
01 00 09 00 Patch USER 10 *4-4 01 00 5E 00 Patch USER 95 *4-4
01 00 0A 00 Patch USER 11 *4-4 01 00 5F 00 Patch USER 96 *4-4
01 00 0B 00 Patch USER 12 *4-4 01 00 60 00 Patch USER 97 *4-4
01 00 0C 00 Patch USER 13 *4-4 01 00 61 00 Patch USER 98 *4-4
01 00 0D 00 Patch USER 14 *4-4 01 00 62 00 Patch USER 99 *4-4
01 00 0E 00 Patch USER 15 *4-4
01 00 0F 00 Patch USER 16 *4-4
01 00 10 00 Patch USER 17 *4-4
01 00 11 00 Patch USER 18 *4-4
01 00 12 00 Patch USER 19 *4-4
01 00 13 00 Patch USER 20 *4-4
01 00 14 00 Patch USER 21 *4-4
01 00 15 00 Patch USER 22 *4-4
01 00 16 00 Patch USER 23 *4-4
01 00 17 00 Patch USER 24 *4-4
01 00 18 00 Patch USER 25 *4-4
01 00 19 00 Patch USER 26 *4-4
01 00 1A 00 Patch USER 27 *4-4
01 00 1B 00 Patch USER 28 *4-4
01 00 1C 00 Patch USER 29 *4-4
01 00 1D 00 Patch USER 30 *4-4

45
 Chapter 6 Appendices

Table 4-2. System offset MIDI bank MIDI Program GR-20 Patch
select MSB Change Number Number
0C 02 6 1 MSB
offset ID min max max
(dec) (hex) 0C 03 LSB
00 GK SENS 1 0 8 08 0="1" - 8="9" :
01 GK SENS 2 0 8 08 0="1" - 8="9" :
:
02 GK SENS 3 0 8 08 0="1" - 8="9"
0D 7E 6 127 MSB
03 GK SENS 4 0 8 08 0="1" - 8="9"
0D 7F LSB
04 GK SENS 5 0 8 08 0="1" - 8="9"
0E 00 7 0 MSB
05 GK SENS 6 0 8 08 0="1" - 8="9"
0E 01 LSB
06 OUTPUT 0 1 01 0="Ln", 1="GA"
0E 02 7 1 MSB
LINE/AMP
0E 03 LSB
07 SW MODE 0 1 01 0="1", 1="2"
:
08 MIDI CH 0 10 0A 00H="1ch" -
:
0aH="11ch"
:
09 MIDI 0 1 01 0="MONO",
0F 7E 7 127 MSB
MONO/ 1="POLY"
POLY 0F 7F LSB
0A MASTER 0 127 7F 3fH="440.0Hz" 10 00 8 0 MSB
TUNE 10 01 LSB
0B reserve 7 7 07 10 02 8 1 MSB
0C GUITAR/ 0 1 01 0="GUITAR", 10 03 LSB
BASS GUITAR 1="BASS GUITAR" :
0D reserve 0 0 00 :
0E reserve 0 0 00 :
0F reserve 0 0 00 11 7E 8 127 MSB
11 7F LSB
12 00 9 0 MSB
Table 4-3. Patch Link Map 12 01 LSB
12 02 9 1 MSB
12 03 LSB
offset MIDI bank MIDI Program GR-20 Patch
select MSB Change Number Number :
00 00 0 0 MSB :
:
00 01 LSB
13 7E 9 127 MSB
00 02 0 1 MSB
13 7F LSB
00 03 LSB
14 00 10 0 MSB
:
14 01 LSB
:
: 14 02 10 1 MSB
01 7E 0 127 MSB 14 03 LSB
01 7F LSB :
02 00 1 0 MSB :
:
02 01 LSB
15 7E 10 127 MSB
02 02 1 1 MSB
15 7F LSB
02 03 LSB
:
: /Example using RQ1/
: To extract the all system parameters, send the following message to the GR-20.
03 7E 1 127 MSB
03 7F LSB
F0 41 10 00 72 11 00 00 00 00 00 00 00 10 70 F7
04 00 2 0 MSB
04 01 LSB
04 02 2 1 MSB /Example using DT1/
04 03 LSB To change OUTPUT LINE/AMP to GA and SW MODE to “2”, send the following message
: to the GR-20.
:
:
F0 41 10 00 72 12 00 00 00 06 01 01 78 F7
05 7E 2 127 MSB
05 7F LSB
06 00 3 0 MSB
06 01 LSB
06 02 3 1 MSB
06 03 LSB
:
:
:
07 7E 3 127 MSB
07 7F LSB
08 00 4 0 MSB
08 01 LSB
08 02 4 1 MSB
08 03 LSB
:
:
:
09 7E 4 127 MSB
09 7F LSB
0A 00 5 0 MSB
0A 01 LSB
0A 02 5 1 MSB
0A 03 LSB
:
:
:
0B 7E 5 127 MSB
0B 7F LSB
0C 00 6 0 MSB
0C 01 LSB

46
 Chapter 6 Appendices

Table 4-4. Patch A-1. Decimal VS Hexadecimal

offset ID min max max Description With a MIDI System, the data value, the address, or size in an exclusive message is
(Hex) (dec) (hex) expressed in 7-bit hexadecimal values.The table below shows decimal value and their
00 Preset PATCH 0 3 03 hexadecimal counterparts.
Number MSB
01 Preset PATCH 0 127 7F
Number LSB Decimal Hex Decimal Hex Decimal Hex Decimal Hex
02 ATTACK 0 99 63 0 00H 32 20H 64 40H 96 60H
03 RELEASE 0 99 63 1 01H 33 21H 65 41H 97 61H
04 CHORUS 0 99 63 2 02H 34 22H 66 42H 98 62H
05 DELAY/RE- 0 99 63 3 03H 35 23H 67 43H 99 63H
VERB 4 04H 36 24H 68 44H 100 64H
06 LEVEL 0 99 63 5 05H 37 25H 69 45H 101 65H
07 FREQ 0 99 63 6 06H 38 26H 70 46H 102 66H
08 RESO 0 99 63 7 07H 39 27H 71 47H 103 67H
09 TRANSPOSE 0 4 04 0="-2oct", 1="-1oct", 8 08H 40 28H 72 48H 104 68H
2="0", 3="+1oct", 9 09H 41 29H 73 49H 105 69H
4="+2Oct" 10 0AH 42 2AH 74 4AH 106 6AH
0A PLAYFEEL 0 4 04 0–3="1"–"4", 5="nd", 11 0BH 43 2BH 75 4BH 107 6BH
6="St" 12 0CH 44 2CH 76 4CH 108 6CH
0B EXP PEDAL 0 8 08 0="FV", 1="FL", 13 0DH 45 2DH 77 4DH 109 6DH
2="b1", 3="b2",
14 0EH 46 2EH 78 4EH 110 6EH
4="b3", 5="b4",
6="b5", 7="b6", 15 0FH 47 2FH 79 4FH 111 6FH
8="EF" 16 10H 48 30H 80 50H 112 70H
0C HOLD TYPE 0 3 03 0="H1", 1="H2", 17 11H 49 31H 81 51H 113 71H
2="H3", 3="H4" 18 12H 50 32H 82 52H 114 72H
0D GLIDE TYPE 0 19 13 00H="d8", 01H="d7", 19 13H 51 33H 83 53H 115 73H
02H="d6", 03H="d5", 20 14H 52 34H 84 54H 116 74H
04H="d4", 05H="d3", 21 15H 53 35H 85 55H 117 75H
06H="d2", 07H="d1", 22 16H 54 36H 86 56H 118 76H
08H="u1", 09H="u2",
23 17H 55 37H 87 57H 119 77H
0aH="u3", 0bH="u4",
0cH="u5", 0dH="u6", 24 18H 56 38H 88 58H 120 78H
0eH="u7", 0fH="u8", 25 19H 57 39H 89 59H 121 79H
10H="v1", 11H="v2", 26 1AH 58 3AH 90 5AH 122 7AH
12H="v3", 13H="v4" 27 1BH 59 3BH 91 5BH 123 7BH
0E DELAY 0 99 63 28 1CH 60 3CH 92 5CH 124 7CH
0F Reserve 0 0 00 29 1DH 61 3DH 93 5DH 125 7DH
30 1EH 62 3EH 94 5EH 126 7EH
31 1FH 63 3FH 95 5FH 127 7FH
/Example using RQ1/
To extract all the data of patch USER BANK 50, send the following message to the GR-20.
When expressing a MIDI channel number or a program change number, please notice that
F0 41 10 00 72 11 01 00 31 00 00 00 00 10 3D F7 the values are less by one. For example, MIDI channel is expressed as 0 through 15 instead
of 1 through 16.
/Example using DT1/ The range of 7 bit can express 128 steps from 0 to 127. To express broader range, use several
If you want to set as the following the EXP PEDAL parameter of patch USER BANK 10 is data bytes.
“FL”, create data as the following and send it to your GR-20.

F0 41 10 00 72 12 01 00 09 0B 01 6A F7

47
 Chapter 6 Appendices

MIDI Implementation Chart

GUITAR SYNTHESIZER Date : Dec. 18, 2003

Model GR-20 MIDI Implementation Chart Version : 1.00

Transmitted Recognized Remarks

Function...

Basic Default 1–16 *1 1–16 *1 Memorized

Channel Changed 1–16 1–16

Default Mode 3, 4 (M=6) *1 Mode 3, 4 (M=6) Memorized

Mode Messages X X
Altered **************

Note 0–127 0–127

Number : True Voice **************

Note ON O 9n V=1–127 *2 O
Velocity Note OFF O 9n V=0 X

After Key's X X
Touch Ch's X X

Pitch Bend O O
0, 32 O O (MSB only) *3 Bank Select
4 O O *3 Foot Type
Control 6, 38 O X Data Entry
7 O O *3 Volume
Change 18 O O General Purpose 3 (Envelope Follower)
64 O O *3 Hold 1
100, 101 O X RPN LSB, MSB (Pitch Bend Sensitivity only)

Prog O 0–127 O 0–127 *3

Change : True # **************
System Parameters,
System Exclusive O O *4 User Patch Parameters
: Song Pos X X
System
: Song Sel X X
Common
: Tune X X

System : Clock X X
Real Time : Command X X
: All sound off X X
: Reset all controllers X X
: Local ON/OFF X X
Aux : All Notes OFF X O (123–127)
: Active Sense O O
Message : System Reset X X
*1 Can be memorized after powering off.
*2 When PLAY FEEL="nd," v=100.
Notes
*3 Can be received only through the Basic channel.
*4 Can be received when Bulk Load is standby in System mode.

Mode 1 : OMNI ON, POLY Mode 2 : OMNI ON, MONO O : Yes

Mode 3 : OMNI OFF, POLY Mode 4 : OMNI OFF, MONO X : No

48
 Chapter 6 Appendices

Main Specifications • Accessories

Owner’s Manual
GR-20: GUITAR SYNTHESIZER AC Adaptor BRC series
• Sound Generator GK Cable (5 m)
1 part Divided Pickup (GK-3) * not included with the GR-20S
• Maximum Polyphony • Options
48 voices GK Cable: GKC-3 (3 m), GKC-5 (5 m), GKC-10 (10 m)
• Patches Unit Selector: US-20
User: 99 GK Parallel Box: GKP-4
Preset: 469 Divided Pickup: GK-3 (for guitar)

• Display Divided Pickup: GK-3B (for bass guitar)

7 segments, 2 characters (LED) * In the interest of product improvement, the specifications and/
or contents of this package are subject to change without prior
• Effects
notice.
MULTI-FX (included in the patches)
Chorus
Delay/Reverb

• Connectors/Jacks
GK IN
GUITAR OUT
MIX IN L
MIX IN R (MONO)
OUTPUT L (PHONES)
OUTPUT R (MONO)
MIDI IN
MIDI OUT
AC IN

• Power Supply
AC 14 V (AC Adaptor)

• Current Draw
600 mA

• Dimensions
313.8 (W) x 244.9 (D) x 63.1 (H) mm
12-3/8 (W) x 9-11/16 (D) x 2-1/2 (H) inches
Maximum height:
313.8 (W) x 244.9 (D) x 97.5 (H) mm
12-3/8 (W) x 9-11/16 (D) x 3-7/8 (H) inches

• Weight
1.7 kg
3 lbs 12 oz (excluding the AC Adaptor)

49
 INDEX

A O
ATTACK ..................................................................... 9, 20 OUTPUT ..................................................................... 8, 10
OUTPUT LEVEL ........................................................... 10
B OUTPUT SELECT ......................................................... 14
BANK ................................................................................ 8
Bank Select ..................................................................... 29 P
BASIC CHANNEL ........................................................ 29 Patch ................................................................................ 14
Bend Range .................................................................... 29 PATCH EDIT ................................................................... 9
BULK DUMP ................................................................. 26 PATCH LINK SETUP ............................................... 9, 19
BULK LOAD .................................................................. 27 PLAY FEEL ................................................................. 9, 21
Play mode ....................................................................... 12
C Poly .................................................................................. 28
Channel ........................................................................... 18 Poly Mode ...................................................................... 28
CHORUS .................................................................... 9, 20 Program Change ............................................................ 29
Control change .............................................................. 29
CUTOFF FREQEUCY ................................................... 21 R
reference pitch ................................................................ 13
D RELEASE .................................................................... 9, 20
DELAY .............................................................................. 9 RESO ................................................................................. 8
Display .............................................................................. 8 RESONANCE ................................................................ 21
REVERB ............................................................................ 9
E
E FLW .............................................................................. 20 S
Envelope Follower ........................................................ 20 SW MODE ........................................................................ 8
EXIT ................................................................................... 9 SYSTEM EDIT .................................................................. 9
EXP PEDAL ................................................................ 9, 16 system parameter .......................................................... 26
Expression Pedal ..................................................... 16, 23
Expression pedal ............................................................. 9 T
TRANSPOSE .............................................................. 9, 21
F TUNER .............................................................................. 9
Factory Reset .................................................................. 31 Tuner ............................................................................... 13
FREQ ........................................................................... 8, 21
V
G VALUE .............................................................................. 8
GK ...................................................................................... 8
GK IN .............................................................................. 10 W
GLIDE ......................................................................... 9, 15 WRITE ......................................................................... 9, 24
Glide .................................................................................. 9
GLIDE pedal .................................................................... 9
GLIDE TYPE .................................................................. 22
GUITAR OUT ................................................................ 10

H
HOLD .......................................................................... 9, 16
HOLD pedal ..................................................................... 9
HOLD TYPE ................................................................... 23

L
LEVEL ............................................................................... 9
Local Control Off ..................................................... 28, 30

M
MIDI CH ........................................................................... 9
MIDI Channel ................................................................ 29
MIX IN ............................................................................ 10
Mono Mode .................................................................... 28

N
NUMBER .......................................................................... 8

50
 For the U.K.
IMPORTANT: THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE.

BLUE: NEUTRAL
BROWN: LIVE

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
Under no circumstances must either of the above wires be connected to the earth terminal of a three pin plug.

For EU Countries

This product complies with the requirements of European Directive 89/336/EEC.

For the USA

FEDERAL COMMUNICATIONS COMMISSION

RADIO FREQUENCY INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.

Unauthorized changes or modification to this system can void the users authority to operate this equipment.
This equipment requires shielded interface cables in order to meet FCC class B Limit.

For Canada

NOTICE
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

AVIS
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
Information
When you need repair service, call your nearest Roland Service Center or authorized Roland distributor in your country as
shown below.
PHILIPPINES MEXICO IRELAND IRAN
AFRICA G.A. Yupangco & Co. Inc. Casa Veerkamp, s.a. de c.v. Roland Ireland MOCO, INC.
339 Gil J. Puyat Avenue Av. Toluca No. 323, Col. Olivar G2 Calmount Park, Calmount No.41 Nike St., Dr.Shariyati Ave.,
EGYPT Makati, Metro Manila 1200, de los Padres 01780 Mexico D.F. Avenue, Dublin 12 Roberoye Cerahe Mirdamad
Al Fanny Trading Office PHILIPPINES MEXICO Republic of IRELAND Tehran, IRAN
9, EBN Hagar A1 Askalany Street, TEL: (02) 899 9801 TEL: (55) 5668-6699 TEL: (01) 4294444 TEL: (021) 285-4169
ARD E1 Golf, Heliopolis,
SINGAPORE PANAMA ISRAEL
Cairo 11341, EGYPT
SUPRO MUNDIAL, S.A. ITALY
TEL: 20-2-417-1828 Swee Lee Company Roland Italy S. p. A. Halilit P. Greenspoon &
150 Sims Drive, Boulevard Andrews, Albrook,
Panama City, REP. DE PANAMA Viale delle Industrie 8, Sons Ltd.
REUNION SINGAPORE 387381 20020 Arese, Milano, ITALY 8 Retzif Ha'aliya Hashnya St.
TEL: 6846-3676 TEL: 315-0101
Maison FO - YAM Marcel TEL: (02) 937-78300 Tel-Aviv-Yafo ISRAEL
25 Rue Jules Hermann,
CRISTOFORI MUSIC PTE PARAGUAY TEL: (03) 6823666
Chaudron - BP79 97 491
LTD Distribuidora De NORWAY
Ste Clotilde Cedex,
Blk 3014, Bedok Industrial Park E, Instrumentos Musicales Roland Scandinavia Avd. JORDAN
REUNION ISLAND
#02-2148, SINGAPORE 489980 J.E. Olear y ESQ. Manduvira Kontor Norge AMMAN Trading Agency
TEL: (0262) 218-429
TEL: 6243-9555 Asuncion PARAGUAY Lilleakerveien 2 Postboks 95 245 Prince Mohammad St.,
SOUTH AFRICA TEL: (021) 492-124 Lilleaker N-0216 Oslo Amman 1118, JORDAN
That Other Music Shop TAIWAN NORWAY TEL: (06) 464-1200
ROLAND TAIWAN URUGUAY TEL: 2273 0074
(PTY) Ltd. KUWAIT
11 Melle St., Braamfontein, ENTERPRISE CO., LTD. Todo Musica S.A.
Johannesbourg, SOUTH AFRICA Room 5, 9fl. No. 112 Chung Shan Francisco Acuna de Figueroa 1771
POLAND Easa Husain Al Yousifi Est.
MX MUSIC SP.Z.O.O. Abdullah Salem Street,
N.Road Sec.2, Taipei, TAIWAN, C.P.: 11.800
P.O.Box 32918, Braamfontein 2017 UL. Gibraltarska 4. Safat, KUWAIT
R.O.C. Montevideo, URUGUAY
Johannesbourg, SOUTH AFRICA PL-03664 Warszawa POLAND TEL: 243-6399
TEL: (02) 2561 3339 TEL: (02) 924-2335
TEL: (011) 403 4105 TEL: (022) 679 44 19
THAILAND LEBANON
Paul Bothner (PTY) Ltd. VENEZUELA PORTUGAL Chahine S.A.L.
17 Werdmuller Centre, Theera Music Co. , Ltd. Musicland Digital C.A. Tecnologias Musica e Audio, Gerge Zeidan St., Chahine Bldg.,
Main Road, Claremont 7708 330 Verng NakornKasem, Soi 2, Av. Francisco de Miranda,
Roland Portugal, S.A. Achrafieh, P.O.Box: 16-5857
SOUTH AFRICA Bangkok 10100, THAILAND Centro Parque de Cristal, Nivel
Cais Das Pedras, 8/9-1 Dto Beirut, LEBANON
TEL: (02) 2248821 C2 Local 20 Caracas
P.O.BOX 23032, Claremont 7735, 4050-465 PORTO TEL: (01) 20-1441
VENEZUELA
SOUTH AFRICA VIETNAM TEL: (212) 285-8586
PORTUGAL
QATAR
TEL: (021) 674 4030 Saigon Music TEL: (022) 608 00 60
Suite DP-8
Al Emadi Co. (Badie Studio
40 Ba Huyen Thanh Quan Street EUROPE ROMANIA & Stores)
ASIA Hochiminh City, VIETNAM FBS LINES P.O. Box 62, Doha, QATAR
Piata Libertatii 1, TEL: 4423-554
Tel: (08) 930-1969 AUSTRIA
CHINA Roland Elektronische 535500 Gheorgheni, ROMANIA
Roland Shanghai Electronics TEL: (266) 364 609 SAUDI ARABIA
AUSTRALIA/ Musikinstrumente HmbH. aDawliah Universal
Co.,Ltd. Austrian Office RUSSIA Electronics APL
5F. No.1500 Pingliang Road
Shanghai 200090, CHINA
NEW ZEALAND Eduard-Bodem-Gasse 8, MuTek Corniche Road, Aldossary Bldg.,
A-6020 Innsbruck, AUSTRIA 3-Bogatyrskaya Str. 1.k.l 1st Floor, Alkhobar,
TEL: (021) 5580-0800
AUSTRALIA TEL: (0512) 26 44 260 107 564 Moscow, RUSSIA SAUDI ARABIA
Roland Shanghai Electronics Roland Corporation TEL: (095) 169 5043
Co.,Ltd. Australia Pty., Ltd. BELGIUM/HOLLAND/ P.O.Box 2154, Alkhobar 31952
(BEIJING OFFICE) 38 Campbell Avenue LUXEMBOURG SPAIN SAUDI ARABIA
10F. No.18 Anhuaxili Dee Why West. NSW 2099 Roland Electronics TEL: (03) 898 2081
Roland Benelux N. V.
Chaoyang District, Beijing 100011 AUSTRALIA Houtstraat 3, B-2260, Oevel de España, S. A.
CHINA TEL: (02) 9982 8266 (Westerlo) BELGIUM Calle Bolivia 239, 08020 SYRIA
TEL: (010) 6426-5050 TEL: (014) 575811 Barcelona, SPAIN Technical Light & Sound
NEW ZEALAND TEL: (93) 308 1000 Center
Roland Shanghai Electronics Rawda, Abdul Qader Jazairi St.
Roland Corporation Ltd. CZECH REP.
Co.,Ltd.
32 Shaddock Street, Mount Eden,
SWEDEN Bldg. No. 21, P.O.BOX 13520,
(GUANGZHOU OFFICE) K-AUDIO Roland Scandinavia A/S Damascus, SYRIA
Auckland, NEW ZEALAND Kardasovska 626.
2/F., No.30 Si You Nan Er Jie Yi SWEDISH SALES OFFICE TEL: (011) 223-5384
TEL: (09) 3098 715 CZ-198 00 Praha 9,
Xiang, Wu Yang Xin Cheng, Danvik Center 28, 2 tr.
Guangzhou 510600, CHINA CZECH REP.
S-131 30 Nacka SWEDEN TURKEY
Tel: (020) 8736-0428 CENTRAL/LATIN TEL: (2) 666 10529
TEL: (0)8 702 00 20 Ant Muzik Aletleri Ithalat
Ve Ihracat Ltd Sti
HONG KONG AMERICA DENMARK SWITZERLAND Siraselviler Caddesi Siraselviler
Tom Lee Music Co., Ltd. Roland Scandinavia A/S Pasaji No:74/20
Roland (Switzerland) AG
Nordhavnsvej 7, Postbox 880,
Service Division ARGENTINA DK-2100 Copenhagen
Landstrasse 5, Postfach, Taksim - Istanbul, TURKEY
22-32 Pun Shan Street, Tsuen Instrumentos Musicales S.A. CH-4452 Itingen, TEL: (0212) 2449624
Wan, New Territories, DENMARK
Av.Santa Fe 2055 SWITZERLAND
HONG KONG TEL: 3916 6200 U.A.E.
(1123) Buenos Aires TEL: (061) 927-8383
TEL: 2415 0911 Zak Electronics & Musical
ARGENTINA FRANCE
Parsons Music Ltd. TEL: (011) 4508-2700 Roland France SA UKRAINE Instruments Co. L.L.C.
8th Floor, Railway Plaza, 39 4, Rue Paul Henri SPAAK, TIC-TAC Zabeel Road, Al Sherooq Bldg.,
Chatham Road South, T.S.T, BRAZIL Parc de l'Esplanade, F 77 462 St. Mira Str. 19/108 No. 14, Grand Floor, Dubai, U.A.E.
Kowloon, HONG KONG Roland Brasil Ltda Thibault, Lagny Cedex FRANCE P.O. Box 180 TEL: (04) 3360715
TEL: 2333 1863 Rua San Jose, 780 Sala B TEL: 01 600 73 500 295400 Munkachevo, UKRAINE
Parque Industrial San Jose TEL: (03131) 414-40
INDIA Cotia - Sao Paulo - SP, BRAZIL FINLAND NORTH AMERICA
Rivera Digitec (India) Pvt. Ltd. TEL: (011) 4615 5666 Roland Scandinavia As, UNITED KINGDOM
409, Nirman Kendra Mahalaxmi Filial Finland Roland (U.K.) Ltd.
Flats Compound Off. Dr. Edwin COSTA RICA Elannontie 5 Atlantic Close, Swansea CANADA
Moses Road, Mumbai-400011, JUAN Bansbach FIN-01510 Vantaa, FINLAND Enterprise Park, SWANSEA Roland Canada Music Ltd.
INDIA Instrumentos Musicales TEL: (0)9 68 24 020 SA7 9FJ, (Head Office)
TEL: (022) 2493 9051 Ave.1. Calle 11, Apartado 10237, UNITED KINGDOM 5480 Parkwood Way Richmond
TEL: (01792) 702701
San Jose, COSTA RICA GERMANY B. C., V6V 2M4 CANADA
INDONESIA TEL: 258-0211 Roland Elektronische TEL: (604) 270 6626
PT Citra IntiRama Musikinstrumente HmbH.
J1. Cideng Timur No. 15J-150 CHILE Roland Canada Music Ltd.
Jakarta Pusat Comercial Fancy S.A.
Oststrasse 96, 22844 Norderstedt, MIDDLE EAST (Toronto Office)
GERMANY
INDONESIA Rut.: 96.919.420-1 170 Admiral Boulevard
TEL: (040) 52 60090
TEL: (021) 6324170 Mississauga On L5T 2N6
Nataniel Cox #739, 4th Floor BAHRAIN CANADA
Santiago - Centro, CHILE GREECE Moon Stores
KOREA TEL: (02) 688-9540 STOLLAS S.A. No.16, Bab Al Bahrain Avenue,
TEL: (905) 362 9707
Cosmos Corporation Music Sound Light P.O.Box 247, Manama 304,
1461-9, Seocho-Dong, U. S. A.
Seocho Ku, Seoul, KOREA EL SALVADOR 155, New National Road State of BAHRAIN
Roland Corporation U.S.
Patras 26442, GREECE TEL: 211 005
TEL: (02) 3486-8855 OMNI MUSIC 5100 S. Eastern Avenue
75 Avenida Norte y Final TEL: 2610 435400
Los Angeles, CA 90040-2938,
MALAYSIA Alameda Juan Pablo , CYPRUS
Edificio No.4010 San Salvador,
HUNGARY Radex Sound Equipment Ltd.
U. S. A.
BENTLEY MUSIC SDN BHD Roland East Europe Ltd. TEL: (323) 890 3700
EL SALVADOR 17, Diagorou Street, Nicosia,
140 & 142, Jalan Bukit Bintang Warehouse Area ‘DEPO’ Pf.83
TEL: 262-0788 CYPRUS
55100 Kuala Lumpur,MALAYSIA H-2046 Torokbalint, HUNGARY TEL: (022) 66-9426
TEL: (03) 2144-3333 TEL: (23) 511011 As of May 1, 2004 (Roland)

03454467 ’04-8-4N