TENTATIVE TOSHIBA Bi-CMOS INTEGRATED CIRCUIT, SILICON MONOLITHIC

TB1254N
PAL / NTSC / SECAM 1CHIP (IF+VCD PROCESSOR) IC

The TB1254N is a TV signal processor IC, which contains

PIF, SIF, Video, Chroma and deflection signal processors
for worldwide Multi-color systems. Also, it has AV switch
for TV/EXT inputs.

The line-up and flexibility of this TB1251 series contributes

to reduce development costs and components in a TV
sets.
SDIP56-P-600
Weight: 5.55g (typ)
FEATURES
IF STAGE

Multi-system IF TEXT STAGE

SIF 4.5 ~ 6.5 MHz
Built-in AKB

One External BPF for Multi-SIF carrier AKB on/off

Inter carrier inputs AKB Color temperature control

VCO tank coil alignment free
Analog RGB interfaces

for L system,
ABL / ACL
Positive demodulation
V low Ch DEFLECTION STAGE

Built-in H-VCO

ramp distortion correction
VIDEO STAGE

Stand Along Sync in port

Built-in Y delay line (8 adjustable steps)

Built in C trap filter (Switchable)
Sand Castle Pulse Output
(HD+VD+Gate Pulse)
CHROMA STAGE

Multi-color Demoduration AV SWITCH

Visual TV / EXT inputs

Automatic Chroma Identification

1 Xtal for Multi-color Systems
Audio TV / EXT inputs
(3.58MHz/4.43MHz/M-PAL/N-PAL)

Built-in1H Delay line

Cb/Cr input ports

Built-in BPF / TOF

Fsc Output

Two NTSC demodulation phase

TOSHIBA is continually working to improve the quality and the reliability of its products. Nevertheless,
semiconductor devices in general can malfunction or jail due to their inherent electrical sensitivity and
vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to
observe standards of safety, and to avoid situations in which a malfunction or failure of a TOSHIBA product could
cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that
TOSHIBA products are used within specified operating range as set forth in the most recent products specifications.
Also, please keep in mind the precautions and conditions set forth in the TOSHIBA Semiconductor Reliability
Handbook.

The products described in this document are subject to foreign exchange and foreign trade control laws.

The information contained herein is presented only as a guide for the applications of our products. No
responsibility is assumed by TOSHIBA CORPORATION for any infringements of intellectual property or other rights of
th thi d ti hi h lt f it N li i t d b i li ti th i d

Ver3.7 00/01/28 1
 TB1254N BLOCK DIAGRAM

Ver3.7
6.5MHz TRAP



‚a‚o‚e
H Vcc(9V)
PIF tank
H OUT
+

SCL

SDA

Y IN
+
Dig GND

EXT IN

+
+

C in
DC Restor
+

BLACK Det

Dig.VDD
H.AFC

Cb in
Cr in

AFT OUT
TV in
LOOP Filter
FBP IN/SCP OUT

DC NF+
Sync in

MONITOR OUT

YC Vcc(5V)

DE-EMP.

IF DET OUT
EXT AUDIO IN

Hcorr IN/SIF IN
56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29

I2C Bus
IF

6dB DEF Proc.

Y Proc. H,V synchronization
FM DEMOD. Chroma DEMOD. Clamp
PIF Proc. PAL/NTSC/SECAM C-TRAP <c-trap> <Lock det.>
Gain Sw 1H delay line Black Stretch <B.S.>
L-SECAM 1 X'tal <Sync det>
DC restore <DC rest> EHT H/V
<TINT> Y-ƒÁ <ƒÁ> <EHT.H> <AFC1 Gain>
<color system> Y-D.L. <DL> <EHT.V>
<F ID> A.C. <P.SHARP>
<Killer Sence> Sub-Cont <S.CONT>
SIF Clamp Uni-Color <CONT> EW PROC.
Processor BBTINT Bright <BRT> <H.SIZE>
6.5MHz
WPS <EW PARA.>
Half T. <H.T> <TRAPEZIUM>
Uni-SIF beet up Chroma Baseband Proc. <ABL START P> <EW CONER>
<Color> <ABL GAIN>
<Unicolor>
Matrix / SW V PROC.
AUDIO ATT Mode SW
<V.SIZE>
<ATT> <V.LINEAR.>
RGB Interface Cutoff/Drive <V-S CORR.>
<R.G.B.CUTTOFF> <V.SHIFT>
Bright <RGB BRT> <R.G.B.DRIVE>
Uni-Color<RGB CONT> <AKB SW>
BIAS <AKB W/B controle>

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
+
+

+
+

N.C.
Ys/Ym

+
IF AGC

RF AGC
V RAMP

SAW
IK IN
V NFB

G OUT

R OUT
B OUT
V OUT

IF GND
ref R

EXT.G IN
EXT.B IN



EXT.R IN

AUDIO OUT
YC GND

SIF OUT
CW OUT
ABCL IN

Ripple F
APC Filter
RGB Vcc(9V)

4.43MHz X'tal

IF IN

IF Vcc(5V)

00/01/28 2




TERMINAL INTERFACE
PIN NAME FUNCTION INTERFACE
1 IF VCC A Vcc terminal for the IF circuit.
•
Supply 5V.
2 RIPPLE A terminal to be leaded to an internal bias 1
FILTER filter. Put a capacitor. 1kĦ

330Ħ 2kĦ
2 330Ħ
27.5kĦ

45kĦ
5
3 SIF OUT An output terminal for a 1st SIF signal, that 9V
beaten down by a regenerated carrier. 14
The SIF frequencies are able to convert into 100Ħ
only 6.5MHz, in order to eliminate SIF BPFs
to single 6.5MHz.
500Ħ
15kĦ
3
16kĦ
16.3kĦ

5
4 AUDIO OUT An output terminal for audio signal. 9V
FM Det.signal or the external audio signal, 14
100Ħ
input to pin53, is output (Switched by bus).
An internal audio attenator controles the
output levelS. • ATT
4 50kĦ

5.3V
30kĦ
5
5 IF GND The GND terminal for IF circuit.
•
6 IF IN Input terminals for IF signals. Pin 6 and 7 are 1
7 IF IN the both input poles of a differential amplifier. 100kĦ
The norminal input level is 90dB(•V)(Pin6-7),
input impedance is 1.5 k ohms. 6

7
1.44kĦ
1.44kĦ
2.75V
1.5V
5
8 NC
-

Ver3.7 00/01/28 3




PIN NAME FUNCTION INTERFACE

9 RF AGC An output terminal for RF AGC. 9V
14
A pull up resister is required because of its
open collector output, and also connect de-
300Ħ
coupling capacitor to reduce noises,. 9
30kĦ to SELF ADJ

30kĦ
5
10 IF AGC A terminal to be connected to an IF AGC 1
filter. Connect 2.2•F of capacitor to Vcc

10
2kĦ

5
11 APC FILTER A terminal to be connected with an APC filter 42
for chroma demodulation.
This terminal voltage controls the frequency
of VCXO.

110kĦ
11 220Ħ

3.2V

19
12 X’TAL A terminal to be connected with a
42
(4.43MHZ) 4.433619MHz X’tal oscillator. The oscillated
signal lead to chroma demodulation, H out
frequency tuning, AFT and so on.

12 500ƒ ¶
2.5kƒ ¶

19
13 CW OUT An output terminal for the continuous chroma 42
sub-carrier frequency wave, which amplitude
1kĦ
is 0.7Vp-p (typ).
Also the dc level shows killer status, the level
is 1.5V for B/W and 3.5V for Color.
13
200Ħ

19

Ver3.7 00/01/28 4




PIN NAME FUNCTION INTERFACE

14 RGB VCC (9V) A Vcc terminal for RGB block, PIF det. Output
and sound output circuit. •
Supply 9V.
15 YS/YM SW A terminal for switching of EXT RGB Mode 42
•Spot killer and fast Half tone.

15
250Ħ
3.3V 0.7V

14
16 EXT. R IN Input terminals for EXT RGB signals. The 42
17 EXT. G IN signals are clamped by capacitors, therefore
18 EXT. B IN the input impedance should be low, 100
ohms or less is recommended.
For this input, brightness and RGB contrast 250Ħ
are available, also ABL/ACL eliminate the 16 250Ħ
output leval. This ABL/ACL is able to off.
OFF: for small area like OSD 17 250Ħ
ON: for large area like TELETEXT 250Ħ
18 100uA
(input level 0.7Vp-p/100IRE)
2.3V

19
19 Y/C GND The GND terminal for Y/C circuit.
•
20 R OUT Terminals for R/G/B signal output. 14
21 G OUT Connect resistances to GND, if through rate
22 B OUT is not enough. Because of source current
limitation, the resistances should be 2.0k• or
more.
20
100Ħ
21
22
19
23 IK IN An input terminal to sense AKB cathode 42
current. VK

Connect this terminals to GND if not using

1kĦ

the AKB system. 1kĦ

23
2.5kĦ
2.5kĦ

2.5kĦ

12.5kĦ

50kĦ
25kĦ
5kĦ

VF

soft
start

19
limitter
over circuit

Ver3.7 00/01/28 5




PIN NAME FUNCTION INTERFACE

24 V RAMP A terminal to be connected with a capacitor to 31
generate the V.Ramp signal.
The V.Ramp amplitude is kept constant by
the V.AGC.

2.7kĦ
200Ħ
24

V AGC

33
25 V NFB An input terminal for V saw-teeth signal 31
feedback.
If the DC voltage on this pin is less than 1.7V,
it blanks RGB output for V guard.

25
12.5kĦ 2V

V GUARD
33
26 V OUT An output terminal for the vertical driving 31
pulses.

30kĦ
200Ħ
26

1kĦ 0.5V

V OUT read
33
27 REF. R A terminal to be connected with resistance to 31
stabilize internal current sources.

Connect 5.6 k  1% of resistance to GND.

6.8k

27
49k

1.12V

33

Ver3.7 00/01/28 6




PIN NAME FUNCTION INTERFACE

28 ABCL IN An input terminal for ABL/ACL control.
Control voltage range is 5.5•6.0V.
The ratio of ABL against ACL can be set by
bus control.

29 H AFC FILTER A terminal to be connected with H. AFC Filter. 31

The DC voltage of this pin controls the H
VCO frequency.

50Ħ
237Ħ
29

75kĦ
100kĦ

33
30 FBP IN/ SCP An input terminal for FBP. 31
OUT The V and GP Pulses are overlaid as SCP. 3VF
VD

30 3.5V
1.4V

GP

protect
VD H AFC H BLK
33
GP

31 H VCC (9V) A Vcc terminal for DEF circuit, HOUT,

•
IICBUS POR etc.
Supply 9V.
32 H OUT An output terminal for horizontal driving 31
pulses.

50Ħ
32 2VF
6kĦ

33
33 DIG GND A GND terminal for digital block.
•

Ver3.7 00/01/28 7




PIN NAME FUNCTION INTERFACE

34 SCL An input terminal for IICBUS clock. 31

3.25V

34
5kĦ

33
35 SDA An input/output terminal for IICBUS data. 31

3.25V

35
5kĦ

33
36 BLACK DET A terminal to be connected with Black det.
42
filter for black stretch.
This terminal voltage controls Black
stretching gain.
The IIC Bus controls on/off and start point of 4kĦ
Black stretch.
36

2.5V
19
37 DIG. VDD A Vdd terminal for of digital block. H VCC
Supply HVcc voltage through 270 ohms of 31
resistance.
VDD
The voltage of this terminal is clipped in 37
about 3.3V by the internal regulator. 30Ħ 30Ħ
2.6V

30Ħ 750Ħ

Ver3.7 00/01/28 8




PIN NAME FUNCTION INTERFACE

38 SYNC IN An input terminal for Sync signal. 31
The input sync chip is clamped by
charging/discharging the coupling capacitors
832Ħ
so as to align the Sync slice level, therefore
input through low impedance buffer.
(input level 1Vp-p/140IRE) 38 1kĦ 3VF
6kĦ

24kĦ

33
39 Y IN An input terminal for Y signal. 42
The pedestal level is clamped by means of
charging/discharging the coupling capacitor,
therefore input through low impedance buffer.
(1Vp-p/140IRE input level) 39 1kĦ

1kĦ

1kĦ

<Amp> <Clamp> <read Bus>

19
40 DC RESTOR A terminal to be connected with a capacitor to
42
detect the average picture level for DC
restoration.
The ratio of the DC restoration is set by bus.
Leave this terminal open if the DC restoration 50k
is not required. 40
10k

19
41 MON OUT An output terminal of AV SW monitor. 14
The input signal for pin # 46/48 is output
through 6dB amplifier .
(output level 2Vp-p/140IRE)

41
8kĦ

8kĦ

2V
19
42 Y/C VCC An Vcc terminal for Y/C circuit.
•
Supply 5V.

Ver3.7 00/01/28 9




PIN NAME FUNCTION INTERFACE

43 C-IN An input terminal for chroma signal. 42
(standard burst amplitude level 286mVp-p•
The low/High impedance status of this pin
can be read by bus to detect if S port is
connected or not.
43 1kĦ

75kĦ

2.25V

19
44 Cr IN Input terminals for Cb/Cr signals. 42
45 Cb IN This terminal is clamped by charging /
discharging the coupling capacitors, therefore
input with low impedance, 100•or less are
recommended. 44
B.B.TINT•-/+12deg• Sub color control are 2.5V

available for Cb/Cr input signals. 45

clamp
19
46 EXT IN An input terminal for external video signal. 14
(input level 1Vp-p / 140 IRE)
1kĦ

200Ħ 2V

46 1kĦ

19
47 LOOP FILTER A terminal to be connected with loop filter for 5V
1
PIF PLL.
The terminal voltage is controlled PIF VCO 1kĦ
frequency.
1kĦ
500Ħ
47 15kĦ

Ver3.7 00/01/28 10




PIN NAME FUNCTION INTERFACE

48 TV IN An input terminal for TV video signal. 14
(input level 1Vp-p / 140 IRE)
1kĦ

2V

200Ħ
48 1kĦ

19
49 De-Emphasis A terminal to De-Emphasis Audio signal, and 14
•Mon-OUT pick up detected Audio signal. Connect
capacitor (0.01•F to GND.
The time constant 50/75us is set by the
IICBUS control “SIF Freq”.
Remove the capacitor in case of use US/JPN
49 15kĦ 7.5kĦ 500Ħ
sound multiplex system.

5
50 PIF TANK Terminals to connect a PIF tank coil. 1
51 The tank coil should be pre-set up within +/-
2% for the automatic tuning. Manual tuning is
also available.. 50
The resonance capacitance of the tank
should be 18pF.

51

5
52 DC NF A terminal for connect the capacitor for DC 14
NF.

52

2kĦ 10kĦ

Ver3.7 00/01/28 11




PIN NAME FUNCTION INTERFACE

53 EXT AUDIO IN An input terminal for external audio signal. 14
Nominal input level is 500mVrms.

53 35k
35k

4.5V

19
54 IF DET OUT An output terminal of detected PIF. 14
(typical output level 2.2Vp-p) 200Ħ

54
1kĦ

5
55 AFT OUT An output terminal for AFT. 1
output dc range; 0•2.5•5V.
output impedance; 50 k ohms (typ.) 100kĦ

55 100Ħ

100kĦ

1.7V

3.4V
SELF TEST
5
AFT OUT AFT READ
OUT

56 SIF in / H corr. An input terminal for 2’nd SIF signal and 1

H.curve correction.

H corr
500 7pF
56
20kĦ
SIF

2.5V

Ver3.7 00/01/28 12




BUS CONTROL MAP for TB1254N

Write Mode
Slave Address: 88 HEX
Sub D7 D6 D5 D4 D3 D2 D1 D0 PRESET
Addr. MSB LSB
00 WPS Uni-Color 0000 0000
01 B.B. Brightness ( TV / Text ) 0100 0000
02 C-Trap Color 0100 0000
03 N Phase Sharpness 0010 0000
04 Y MUTE RGB Mt RGB Contrast 0110 0000
05 Y D.L. Sub Color 0011 0000
06 Video SW Au SW B.B.Tint 0001 0000
07 N-Comb TINT 0100 0000
08 SECAM R-Y Black Adjust SECAM B-Y Black Adjust 1000 1000
09 S- GP Phase S-ID Sens Bell fo S-Black L-SECAM L-S AGC S-ID 0000 0000
/ S- inhibit Monitor Mode Speed-up Mode
0A PIF Freq SIF Freq. Color System 0000 0000
0B 6.5MHz 0000 0000
Audio Att
SIF Fix
0C BPF/TOF P/N- F ID Coring SIF PIF VCO PIF VCO PIF VCO 0000 0000
ID Sens off 5.74MHz Adj. Stop Adj. Req Center
0D Sprit/•nt• Over Mod Q Det AFT Sens Au Gain AFT Mute STD by Mode 0000 0000
• SW Gain
0E Self Test RF AGC 0000 0000
0F Ysm M RGB DC Restoration Black Stretch  Point 0000 0000
ABCL
10 ABL Start Point ABL Gain Sub Contrast 0000 1000
11 Buzz color -  0001 1000
AKB System
reducer
12 R Cut Off 0000 0000
13 G Cut Off 0000 0000
14 B Cut Off 0000 0000
15 Cb/Cr SW G Drive Gain 0100 0000
16 BLK B Drive Gain 0100 0000
17 H-Stop V-Stop V AGC V Ramp V-Freq. 312/313 0000 0000
Ref. Mode
18 Vertical Position Horizontal Position 0001 0000
19 V Linaerity V S Correction 1000 1000
1A AFC G Vertical Size 0010 0000
1B test(0) test(0) Horizontal Size 0010 0000
1C * * EW Parabola correction 0010 0000
1D EW Trapezium Correction V. EHT 1000 0100
1E VSM SW EW Corner Correction H. EHT 0100 0100
1F Test Mode 0000 0000

READ Mode
7 6 5 4 3 2 1 0
R0 POR IF Lock H Lock IF Level V Freq Color System
R1 Y-IN RGB H-OUT V-OUT PIF VCO V Lock AFT
OUT Adj.
R2 Coil error PIF- VCO SYNC C IN DC Product Code
error det DET
R3 AKB CRT AKB STD/Non P ID N-ID S ID noise
Overflow Warm up finish -STD det

Ver3.7 00/01/28 13




IIC BUS CONROL FUNCTION

WRITE MODE
PIF STAGE
ITEMS BITS DESCRIPTIONS PRESET
RF AGC 6 RF AGC delay point (Pin6-7) 00000
••Sub; 0E h 01: 65 dB(•V) 3F: 100 dB(•V) :Mute
00: IF MUTE Stops Demodulation
IF Freq. 3 Setting IF frequency for digital AFT count down 000
••Sub; 0A h 000: 58.75 MHz 001: 45.75 MHz :58.75MHz
010: 39.5 MHz 011: 38.9 MHz
100: 38.0 MHz 101: 34.47 MHz
110: 33.95 MHz 111: 34.2 MHz
AFT Mute 1 AFT Mute Switch 0:normal
••Sub; 0D h 0: normal 1: AFT defeat (mute)
AFT sens. 1 AFT sensitivity 0:100kHz
••Sub; 0D h 0: 100kHz/v 1: 25kHz/V
Over mod SW 1 on/off the over modulation switch 0:off
••Sub; 0D h 0: off 1: on
Q det. Gain Q detector gain 0:high
••Sub; 0D h 0: high 1: low
L-SECAM Mode 1 L SECAM 0:Not
••Sub; 09 h 0: Not L-SECAM L-SECAM
1: L-SECAM
turn the polarity for TV Det Out •for positive modulation•
Delay the AGC time constant (Peek AGC)
SIF AM demodulation
L-SECAM AGC 1 Speed up the AGC sense for channel serch 0:normal
Speed 0: normal
••Sub; 09 h 1: speed-up •Ch Serch•
VCO Center 1 VCO center SW 0: normal
••Sub; 0C h 0: normal 1: Center
In adjusting a tank coil, set this bit to 1.
VCO Adj. Request 1 VCO adjust trigger 0: normal
••Sub; 0C h 0: normal 1: VCO adjust trigger
The PIF VCO starts adjusting after requested.
While adjusting, the picture is blanked
VCO Adj. Stop 1 Stop the readjustment on detecting the loosing adjustment 0: normal
••Sub; 0C h 0: normal 1: stop self adjustment
“VCO Adj request” prier it

SIF STAGE
ITEMS BITS DESCRIPTIONS PRESET
SIF Freq. 2 SIF Frequency 00:5.5MHz
••Sub; 0A h 00: 5.5MHz 01: 6.0MHz
10: 6.5MHz 11: 4.5MHz
Set the SIF frequency for;
Select the SIF FM demodulator band
select the de-emphasis speed
Set the ref.freq. for single •••MHz beet up if using
SIF 574 1 Set the SIF freq. to 5.74MHz for IGR Bilingual. 0:other
••Sub; 0C h It sets the reference freq. for beet up the 5.74MHz to 6.5MHz. frequencies
0: other frequencies 1: 5.74MHz

Ver3.7 00/01/28 14




ITEMS BITS DESCRIPTIONS PRESET

Audio ATT 7 Audio attenuator 00: Mute
••Sub; 0B h 00: Mute 01: -85 dB ~ 7F: 0 dB
Au Gain 1 Audio Gain Switch 0:
••Sub; 0D h 0: 927mVrms at 25kHz/DEV 927mVrms
1: 500mVrms at 25kHz/DEV at
25kHz/DEV
6.5MHz SIF Fix 1 Beet up the SIF carrier frequency to 6.5MHz (single carrier) 0: normal
••Sub; 0A h 0: normal 1: beet up to uni- 6.5MHz
Buzz Reducer 1 Nyquist Buzz Reducer SW 0: on
••Sub; 11 h 0: on 1: off

VIDEO STAGE
ITEMS BITS DESCRIPTIONS PRESET
Sharpness 6 Sharpness control peak:2.75MHz 00:-5.4dB
••Sub; 03 h 00: -5.4dB ~ 20: 3.3dB ~ 3F: 6.6 dB
DC Rest. 2 DC Restoration control 00:120%
••Sub; 0F h 00: 120% 01: 90%
10: 100% 11: 110%
Black Stretch 2 Set the black stretch start point 00: off
••Sub; 0F h 00: off 01: 25IRE
10: 35IRE 11: 45IRE
•point 2 Set the non linear  curve for Y signal 00: off
••Sub; 0F h 00: off 01: 90IRE
10: 80IRE 11: 70IRE
Y DL 3 Y Delay time 001: 0ns
••Sub; 05 h 000: -40ns 100: +120ns
001: 0ns 101: +160ns
010: +40ns 110: +200ns
011: +80ns 111: +240ns
C-Trap 1 Chroma trap filter for Y input 0:OFF
••Sub; 02 h 0: OFF for Y / C Separated input
1: ON for internal C trap(-20dB or less)
WPS 1 White Peak Suppresser Switch 0:ON
••Sub; 00 h 0: ON 1: OFF
coring SW 1 on/off the coring 0: on
••Sub; 0Ch 0: on 1: off

Ver3.7 00/01/28 15




CHROMA STAGE
ITEMS BITS DESCRIPTIONS PRESET
TINT 7 Tint control for NTSC (CW TINT) 00:0deg
••Sub; 07 h 00: -33 deg ~ 7F: 33 deg
Color System 3 Color system switch 000: Auto 1
••Sub; 0A h 000: Auto 1 443PAL , 358NTSC , SECAM , 443NTSC
001: Auto 2 358NTSC , M-PAL , N-PAL (for S-America)
010: Fixed 358NTSC 011: Fixed 443NTSC
100: Fixed 443PAL 101: Fixed SECAM
110: Fixed M PAL 111: Fixed N PAL
N-Comb 1 Comb filter for base-band color signal of NTSC 0: ON
••Sub; 07 h 0: ON 1: OFF
2 set the relative phase / amplitude 00:NTSC1
NTSC Phase
00: NTSC1 (90 deg) 01: NTSC2 (105 deg) (90 deg)
••Sub; 03 h
10/11: DVD (90 deg, 245 deg) for U/V inputs
BPF/TOF 1 Select chroma BPF frequency responce 0:BPF
••Sub; 0C h 0: BPF for EXT input 1: TOF for RF input
1 PAL / NTSC ID sensitivity for digital comb filter 0:Normal
P/N ID Sens
0: Normal 1: Low
••Sub; 0C h.
F ID 1 Forced killer off 0:normal
••Sub; 0E h 0: normal 1: always color on in a fixed color
systems
(This function dose not work in Auto 1 and Auto 2 mode)

SECAM STAGE
ITEMS BITS DESCRIPTIONS PRESET
SECAM GP Phase 2 SECAM ID phase / SECAM inhibit 00:+200ns
/ SECAM inhibit 00: +200ns 01: normal
10: -200ns 11: SECAM inhibit
S Black Adj. R-Y 4 SECAM Black level adjust 1000: 0 mV
••Sub; 08 h 0: -92 mV ~ F: +85mV
14mV/dev
S Black Adj. B-Y 4 SECAM Black level adjust 1000: 0mV
••Sub; 08 h 0: -92 mV ~ F: +85mV
14mV/dev
Bell fo 1 SECAM Bell filter fo shift 0:0 kHz
••Sub; 09 h 0: 0 kHz 1: +35 kHz
S ID sense 1 SECAM ID Sensitivity 0:normal
••Sub; 09 h 0: normal 1: Low
S ID mode 1 SECAM ID mode 0:H
••Sub; 09 h 0: H 1: H+V
S Black monitor 1 SECAM Black level alignment mode 0:normal
••Sub; 09 h 0: normal 1: Alignment

TEXT STAGE
ITEMS BITS DESCRIPTIONS PRESET
Uni-Color 7 Uni-Color control 0000000
••Sub; 00 h 00: -12 dB ~ 7F: 12dB :0dB
Brightness 7 Brightness control 1000000
••Sub; 01 h 00: 1.75 V ~ 7F: 3.25 V (Pedestal Level) :2.50V
Color 7 Color control 1000000
••Sub; 02 h 00: -20 dB or less ~ 7F: 6.5 dB :0dB

Ver3.7 00/01/28 16




ITEMS BITS DESCRIPTIONS PRESET

RGB Contrast 6 Contrast control for RGB input 100000
••Sub; 04 h 00: -8.0 dB ~ 3F: 11.4 dB 0.2Vinpuit :6.2dB
Cb/Cr SW 1 Cb/Cr Switch 0:
••Sub; 05 h 0: Cb/Cr internal 1: Cb/Cr external Cb/Cr internal
Sub-color 5 Sub color control (for Cb/Cr input) 100000
••Sub; 05 h 00: -3 dB or less ~ 7F: +3 dB :0dB
B.B Tint 5 Base band tint control (for Cb/Cr input) 10000
••Sub; 06 h 00: -12deg 1F: +12deg :0deg
Sub-Contrast 4 Sub contrast control 1000
••Sub; 10 h 0: -3 dB ~ F: 2.5 dB :0dB
ABL Start Point 2 Selecting ABL start point 00:0V
••Sub; 10 h 00: 0V 01: -0.20V 10: -0.30 V 11: -0.50 V
ABL Gain 2 ABL Gain control 00:-0.21V
••Sub; 10 h 00: -0.21 V 01: -0.38 V 10: -0.50 V 11: -0.67 V
B. B. 1 Blue Back Switch 0: FF
••Sub; 06 h 0: OFF 1: ON (50 IRE )
Color • 1 on/off the color • 0:OFF
••Sub; 11 h 0: OFF 1: ON
RGB - Cutoff 8 R,G,B Cutoff control 00:-0.65 V
••Sub; 12~14 h 00: -0.65 V ~ FF: 0.65 V
G/B Drive 7 G,B Drive control 0000000
••Sub; 15~16 h 00: -5.5 dB ~ 7F: 3.5 dB :0dB
BLK 1 Hor. And Vert. blanking for RGB outputs 0
••Sub; 16 h 0: Blanking ON ( Normal mode) :Blanking ON
1: Blanking OFF
AKB System 6 00: AKB off(bus control) 11:AKB cut
••Sub; 11 h 10: ACB cutoff -> align to targets off , drive
drive -> BUS control
11: AKB cut off , drive -> align to targets
Y-Mute 1 on / off the Y MUTE 0:off
••Sub; 04 h 0: off 1: on
RGB-Mute 1 on / off the RGB mute 1:on
••Sub; 04 h 0: off 1: on
Ysm Mode 1 Select the Ys mode 0:Half tone
••Sub; 0F h 0: Half tone mode (TV / HT / Ext RGB) mode
1: Blank (TV / Ext RGB / Blank)
RGB ABCL 1 on / off the ABL / ACL for Ext. RGB 0: on
••Sub; 0F h 0: on 1: off

DEF STAGE
ITEMS BITS DESCRIPTIONS PRESET
Vertical Position 3 Vertical Position control by delaying the V-ramp timing 0:0H
••Sub; 18 h 0: 0H ~ 7: 7H
Horizontal Position 5 Horizontal Position control 10000:0ms
••Sub; 18 h 00: -3ms ~ 1F: 3ms
V-Freq 3 Vertical frequency pull-in mode selection 000:AUTO
••Sub; 17 h 000: AUTO
001: 50 Hz
010: 60 Hz
011: Forced 50Hz on no input
100:: Forced 312.5 H Stops V-synchronization
101: Forced 262.5 H Stops V-synchronization
110: Forced 313 H Stops V-synchronization
111: Forced 263 H Stops V-synchronization

Ver3.7 00/01/28 17




ITEMS BITS DESCRIPTIONS PRESET

AFC Gain 2 Select AFC gain 00:Normal
••Sub; 1A h 00: Normal
01: 1 / 3 sensitivity
10: X 3 at V blanking duration
11: AFC OFF
V-stop 1 0: off 0:off
••Sub; 17 h 1: on
H STP 1 H OUT stop 0:normal
••Sub; 17 h 0: normal 1 & Y-mute & RGB mute; H STOP
312/313 Mode 1 Synchronize the V freq. to 312/313 0:normal
••Sub; 17 h 0: normal 1: TELETXT(312/313) Forced sync
V-AGC 1 V AGC sensitivity 0:normal
••Sub; 17 h 0: normal 1: X 5
Vertical Size 6 Vertical size alignment 100000:0%
••Sub; 1A h 00: -40 % ~ 3F: 40 %
V Linearity 4 V linearity alignment 1000:0%
••Sub; 19 h 0: 16 % at upper side , -20 % at lower side
~ F: -14 % at upper side , 17.5 % at lower side
V-S Correction 4 V-S correction 1000:0%
••Sub; 19 h 0: 12 % at upper side , 15 % at lower side
~ F: -12 % at upper side , -15 % at lower side
V Ramp Ref. 1 Select the reference voltage 0:External
••Sub; 17 h 0: External(YC Vcc) 1: Internal

AV SW, OTHERS
ITEMS BITS DESCRIPTIONS PRESET
Video SW 2 Video input selecting switch 00:TV
••Sub; 06 h 00: TV (10: TV + C in)
01: EXT (11: EXT + C in)
Au SW 1 Audio input selecting Switch 0:TV
••Sub; 06 h 0: TV 1: EXT
STD by Mode 2 Stand by mode 00,:normal
••Sub; 0D h 00,01: normal
10 : IF (Working IF Block ,IICBUS and 443VCXO)
11 : STD-by (Working IICBUS and 443VCXO )
Self Test 2 Selecting out put on AFT terminal for self Adjustment 00:AFT
••Sub; 0E h 00: AFT (Normal) 10: RF AGC X 1/2 (Normal)
TEST 8 For testing / Leave these bits preset data ; 0000 0000 00000000
••Sub; 1F h

Ver3.7 00/01/28 18




READ MODE
item bits Description preset
POR 1 Power on reset
0: normal 1: Resister Preset
IF Lock Det 1 IF lock detection
0: Lock out 1: Lock in
H Lock Det 1 Horizontal lock detection
0: Lock out 1: Lock in
IF level 1 IF AGC gain detection
0: High IF AGC gain 1: Low IF AGC gain
Monitoring the IF AGC level to detect if the IF input level is weak or
not.
( The threshold level is around 50 ~ 60 dB
V Freq 1 Vertical Frequency
0: 50 Hz 1: 60 Hz
Color System 3 Present color system status
000: B / W 001: 4.43 PAL
010: M-PAL 011: N-PAL
100: 358 NTSC 101: 443 NTSC
110: SECAM 111: N/A
Y-in 1 Y in for self diagnostic
0: no signal 1: detected
RGB OUT 1 RGB OUT for self diagnostic
0: no signal 1: detected
H OUT 1 H OUT for self diagnostic
0: detected 1: no signal
V OUT 1 V OUT for self diagnostic
0: detected 1: no signal
PIF VCO Adj. Turn to 1 while the PIFVCO
0: normal 1: PIF VCO adjusting
V Lock 1 V Lock for self diagnostic
0: Lock out 1: detected
AFT 2 AFT status
00: Lock OUT 01: too high
10: too low 11: Good
Sync Det 1 Detecting if the H sync. pulses are or are not.
0: no signal 1: detected
C-in DC 1 The DC voltage on C input terminal. It is for detecting the S-jack
swith.
0: open 1: Low
Product code 3 000: TB1258 001: TB1251
010: TB1252 011: TB1253
100: TB1254 101: TB1255
110: TB1256 111: TB1257
AKB Overflow 1 0: normal 1: overflowed
CRT Warm up 1 0: normal 1: not warm up
AKB Finish 1 0: active 1: finished
STD/Non -Std 1 0: non-standard V freq. 1: Standard V freq.
P-ID 1 0: detected 1: not identified
N-ID 1 0: detected 1: not identified
S ID 1 0: detected 1: not identified
Noise det 1 1: normal 0: Large noise level
PIF VCO error detect 1 0: normal 1:error detect
Coil error 1 0: OK 1:NG

Ver3.7 00/01/28 19




2
DATA TRANSFER FORMAT VIA I C BUS
Start and stop condition

SDA

SCL
S P
Start condition Stop condition

Bit transfer

SDA

SCL

SDA stable Change of SDA allowed

Acknowledge
SDA by The transmitter releases the SDA line (HIGH)
transmitter during the acknowledge clock pulse.

SDA by
The receiver has to pull down the SDA line
receiver
(LOW) during the acknowledge clock pulse.

SCL from
master 1 8 9
S

Clock pulse for acknowledgment

Data transmit format 1

S Slave address 0 A Sub address A Transmit data A P
7bit 8bit 8bit
MSB MSB MSB
S : Start condition A : Acknowledge P : Stop condition

Data transmit format 2

S Slave address 0 A Sub address A Transmit data 1 A

Sub address A Transmit data n A P

Data received format

S Slave address 1 A Received data 01 A Received data 02 A P
7bit 8bit
MSB MSB

At the moment of the first acknowledge, the master transmitter becomes a master receiver and the slave receiver
becomes a slave transmitter. This acknowledge is still generated by the slave.
The Stop condition is generated by the master.

Ver3.7 00/01/28 20




Optional data transmit format : automatic increment mode

S Slave address 0 A 1 Sub address A Transmit data 1 Transmit data n A P
7bit 7bit 8bit 8bit
MSB MSB MSB MSB

In this transmission methods, data is set on automatically incremented sub-address from the specified sub-address.

2 2
Purchase of TOSHIBA I C components conveys a license under the Philips I C Patent Rights to use these components
2 2
in an I C system, provided that the system conforms to the I C Standard Specification as defined by Philips.

Ver3.7 00/01/28 21




MAXIMUM RATINGS (Ta=25•)

ITEM SYMBOL RATING UNIT
Supply Voltage (9V Vcc) Vcc max9 12 •
Supply Voltage (5V Vcc) Vcc max• 8 •
Power Dissipation PD max 1980(*1) mW
Input terminal Voltage V in GND – 0.3 ~ Vcc + 0.3 V
Operating Temperature Topr -20 ~ 65 •
Storage Temperature Tstg -55 ~ 150 •

(*1)When using this device at above Ta=25•, the power dissipation decreases by 15.9mV per 1• rise.
(*2) This IC is not proof enough against a strong E-M field by CRT which may cause function errors and/or poor
Characteristics. Keeping the distance from CRT to the IC longer than 20 cm, or if cannot, placing shield metal
over the IC, is recommended in an application.
(*3)Pin 1,4,5,6,9,11,12,13,19,26,31,32,33,34,35,37,42,43,50,51 are weak against static electoricity and surge impulse.
Please take counter measure to meet, if necessary.

Ta-PD Curve ( on a PCB)

1980
PD (mW)

1349
Power Dissipation

0 65 150

Atmosphere Temperature (
‚ƒ

Ta•@ )

RECOMMENDED OPERATING POWER SUPPLY VOLTAGE

PIN NO. PIN NAME MIN. TYP. MAX. UNIT NOTE

1 IF Vcc 4.75 5 5.25 V •
14 RGB VCC (9V) 8.55 9 9.45 V •
31 H VCC (9V) 8.55 9 9.45 V •
37 DIGITAL VDD 3.1 3.3 3.5 V •
42 Y/C VCC (5V) 4.75 5 5.25 V In the condition that IIC BUS data “V
Ramp Ref.” is 0:External(Y/C Vcc),
the thermal drift of the Y/C Vcc
should be less than 50mV.

Ver3.7 00/01/28 22




ELECTRICAL CHARACTERISTICS

CURRENT CONSUMTION
PIN NO. PIN NAME SYMBOL CONDITION MIN. TYP. MAX. UNIT
1 IF Vcc Icc1 Supply 5V 27.9 37.2 46.5 mA
14 RGB VCC (9V) Icc14 Supply 9V 22.8 30.4 38.0 mA
31 H VCC (9V) Icc31 Supply 9V 14.5 19.3 24.1 mA
37 DIGITAL VDD Icc37 Supply 3.3V 16.3 21.7 27.1 mA
42 Y/C VCC (5V) Icc42 Supply 5V 74.4 99.2 124.0 mA

DC CHARACTERISTIC

PIN VOLTAGE
PIN NO. PIN NAME SYMBOL CONDITION MIN. TYP. MAX. UNIT
2 RIPPLE FILTER V2 3.1 3.8 4.5 V
3 SIF OUT V3 1.4 3 3.6 V
4 AUDIO OUT V4 3.2 3.6 4.2 V
6 IF IN V6 0.9 1.5 2.1 V
11 APC FILTER V11 2.5 3.2 3.9 V
12 X’TAL (4.43MHZ) V12 3 3.3 3.6 V
13 CW OUT V13 2.9 3.3 3.7 V
16 EXT. R IN V16 1.5 2.2 2.9 V
17 EXT. G IN V17 1.5 2.2 2.9 V
18 EXT. B IN V18 1.5 2.2 2.9 V
20 R OUT V20 2.15 2.5 2.85 V
21 G OUT V21 2.15 2.5 2.85 V
22 B OUT V22 2.15 2.5 2.85 V
23 IK IN V23 1.1 1.4 1.7 V
27 REF. R V27 0.8 1.1 1.4 V
28 ABCL IN V28 5.7 6.1 6.4 V
29 H AFC FILTER V29 6 6.8 7.5 V
38 SYNC IN V38 1.9 2.2 2.6 V
39 Y IN V39 2.1 2.4 2.8 V
40 DC RESTOR V40 1.5 2.3 3.5 V
41 MON OUT V41 2.65 3 3.35 V
43 C-IN V43 1.8 2.1 2.4 V
44 Cr IN V44 1.7 2.4 3.1 V
45 Cb IN V45 1.7 2.4 3.1 V
46 EXT IN V46 1.2 1.5 1.9 V
47 LOOP FILTER V47 2 2.5 3 V
48 TV IN V48 1.2 1.5 1.9 V
49 DE-EMP V49 4 4.5 5 V
50 PIF VCO V50 2.9 3.5 4.1 V
51 PIF VCO V51 2.9 3.5 4.1 V
53 EXT AUDIO IN V53 3.9 4.5 5.1 V
54 IF DET OUT V54 4.7 5.2 5.7 V
55 AFT OUT V55 2 2.5 3 V
56 H CORR/SIF IN V56 2.4 3 3.6 V

Ver3.7 00/01/28 23




AC CHARACTERISTIC

PIF STAGE
TEST TEST
ITEM SYMBOL MIN TYP MAX UNIT
CIRCUIT CONDITON
PIF input sensitivity vin min(p) - - 42 47 dBV
PIF maximum input signal vin max(p) - P1 100 105 -
PIF gain control range RAGC(p) - 53 63 - dB
RF AGC maximum output voltage VAGC max - - V
P2
RF AGC minimum output voltage VAGC min - - - 0.3
RF AGC delay point (minimum) v Dly min - - 70 80 dBV
P3
RF AGC delay point (maximum) v Dly max - 100 110 -
PIF input resistance (*) Zin R(p) - - - k•
P4
PIF input capacitance (*) Zin C(p) - - - pF
Differential gain DG - - 2.0 5.0 %
P5
Differential phase DP - - 2.0 5.0 deg.
Intermodulation IM - P6 40 45 - dB
Video output signal amplitude (Nega) V Det (p)n - 2.0 2.2 2.4 V
P7
Video output signal amplitude (Posi) V Det (p)p 2.0 2.2 2.4
Video output S/N S/N(p) - P8 50 55 - dB
Synchronous signal level (Nega) Vsync n - 2.6 V
P9
Synchronous signal level (Posi) Vsync p - 2.6
Video bandwidth (-3dB) fDet(p) - P10 6 8 - MHz
Capture range of the PLL (Upper) fpH(p) - 1.5 3.5 -
Capture range of the PLL (Lower) fpL(p) - - -2.2 -1.5 MHz
P11
Hold range of the PLL (Upper) fhH(p) - 1.5 3.5 -
Hold range of the PLL (Lower) fhL(p) - - -2.2 -1.5
Control steepness of the VCO  - P12 - 3.0 - MHz/V
Steepness of the AFT Detection SAFT(S) - kHz/V
(steep) 20 25 30
Steepness of the AFT Detection SAFT(G)
P13 75 100 125
(gentle)
AFT maximum output voltage VAFT max - 4.5 4.8 -
AFT minimum output voltage VAFT min - - 0.2 0.5 V
AFT output voltage on defeating •AFT Def - P14 2.3 2.5 2.7
(*) Not tested

SIF STAGE
TEST TEST
ITEM SYMBOL MIN TYP MAX UMIT
CIRCUIT CONDITION
Limiting sensitivity (4.5MHz High) vin lim(s)4.5MH - 45 50
Limiting sensitivity (4.5MHz Low) vin lim(s)4.5ML - 40 45
Limiting sensitivity (5.5MHz) vin lim(s)5.5M - S1 - 40 45
Limiting sensitivity (6.0MHz) vin lim(s)6.0M - - 40 45
Limiting sensitivity (6.5MHz) vin lim(s)6.5M - - 45 50
AM reduction ratio (4.5MHz High) AMR4.5MH - 50 55 -
dB
AM reduction ratio (4.5MHz Low) AMR 4.5ML - 50 55 -
AM reduction ratio (5.5MHz) AMR5.5M - S2 50 55 - dB
AM reduction ratio (6.0MHz) AMR6.0M - 50 55 -
dB
AM reduction ratio (6.5MHz) AMR6.5M - 50 55 -
AF output signal amplitude (4.5MHz
vDet(s)4.5MH - 649 927 1324 mVrms
High)
AF output S/N AF output signal
S/N(s)4.5MH - S3 50 55 - dB
amplitude (4.5MHz High)
Total harmonics distortion AF output
THD4.5MH - - 0.5 1.0 %
signal amplitude (4.5MHz High)
AF output signal amplitude (4.5MHz
vDet(s)4.5ML S4 350 500 710 mVrms
Low)

Ver3.7 00/01/28 24




TEST TEST
ITEM SYMBOL MIN TYP MAX UMIT
CIRCUIT CONDITION
AF output S/N AF output signal
S/N(s)4.5ML 50 55 - dB
amplitude (4.5MHz Low)
Total harmonics distortion AF output
THD4.5ML - 0.5 1.0 %
signal amplitude (4.5MHz Low)
AF output signal amplitude
vDet(s)5.5M - 695 927 1236 mVrms
(5.5MHz)
AF output S/N AF output signal
S/Ns)5.5M - S5 53 58 - dB
amplitude (5.5MHz)
Total harmonics distortion AF output
THD5.5M - - 0.5 1.0 %
signal amplitude (5.5MHz)
AF output signal amplitude
vDet(s)6.0M - 695 927 1236 mVrms
(6.0MHz)
AF output S/N AF output signal 53
S/N(s)6.0M - S6 58 - dB
amplitude (6.0MHz)
Total harmonics distortion AF output
THD6.0M - - 0.5 1.0 %
signal amplitude (6.0MHz)
AF output signal amplitude
vDet(s)6.5M - 695 927 1236 mVrms
(6.5MHz)
AF output S/N AF output signal
S/N(s)6.5M - S7 53 58 - dB
amplitude (6.5MHz)
Total harmonics distortion AF output
THD6.5M - - 0.5 1.0 %
signal amplitude (6.5MHz)
Demodulation band width of the FM
fpH(s)1 - 5.0 - -
demodulator (Upper1)
S8
Demodulation band width of the FM
fpL(s)1 - - - 4.0
demodulator (Lower1)
Demodulation band width of the FM
fpH(s)2 - 7.0 - -
demodulator (Upper2)
S9 MHz
Demodulation band width of the FM
fpL(s)2 - - - 5.0
demodulator (Lower2)
Audio attenuater gain (Max) G att max - -2 0 2
Audio attenuater gain (Mid) G att mid - S10 - -15 - dB
Audio attenuater gain (Min) G att min - - -85 -75
Audio attenuater off-set Vos att - S11 -50 50 +150 mV
Audio switch cross-talk (TV•EXT) CT(s)T-E - - -75 -65
S12 dB
Audio switch cross-talk (EXT•TV) CT(s)E-T - - -60 -55
Audio switch off-set Vos sw - S13 - - ±30 mV
(*) Not tested

VIDEO STAGE
TEST TEST
ITEM SYMBOL MIN TYP MAX UNIT
CIRCUIT CINDITION
TV Input Dynamic range DRTV V1 0.9 1.0 • V p-p
External Input Dynamic Range DREXT 0.9 1.0 • V p-p
TV mode Gain GTV V2 5.7 6.0 6.3 dB
External mode Gain GEXT 5.7 6.0 6.3 dB
AV SW Cross Talk (TV -> Ext) CTSWTE V3 -60 -55 -50 dB
AV SW Cross Talk (Ext -> TV) CTSWET -60 -55 -50 dB
Y Input Dynamic Range ••Y V4 0.9 1.0 • Vp-p
Y Input Pedestal Clamp Voltage •YCLP V5 2.5 2.7 2.9 V
Y frequency response FRY V6 6.5 8.0 • MHz
Y Delay time tYDEL V7 370 460 550 ns
-40ns tYDEL-40 -44 -38 -34 ns
240ns tYDEL240 214 238 254
1step tYDEL 1step 34 38 44
Brightness Control Characteristics VBRTMAX V8 2.80 3.25 3.70 V
VBRTCEN 2.20 2.50 2.80
VBRTMIN 1.30 1.75 2.20
Brightness Control resolution •VBRT 4.70 11.8 19.0 MV/bit
Uni-color Control Characteristics •UCYMAX V9 10.2 11.6 13.2 dB

Ver3.7 00/01/28 25




TEST TEST
ITEM SYMBOL MIN TYP MAX UNIT
CIRCUIT CINDITION
•UCYCEN 4.2 5.7 7.2
•UCYMIN -9.8 -7.8 -5.8
Sub Contrast Control Characteristics •SCONMAX V10 1.5 2.5 3.5 dB
•SCONMIN -4.0 -3.0 -2.0
Sharpness Peaking Frequency •SHP V11 2.05 2.75 3.80 MHz
Sharpness Control Characteristics •SHMAX V12 3.6 6.6 9.6 dB
•SHCEN 1.3 3.3 5.
•SHMIN -8.4 -5.4 -2.4
Y • correction start point VY• 70 V13 70 73 76 IRE
VY• 80 77 80 83
VY• 90 84 87 90
Y • correction curve GY• -5 dB
Black Expansion AMP Gain •BLEX V14 1.05 1.2 1.45
Black Expansion Start Point VBLEX 25IRE 21 25 29 V
VBLEX 35IRE 30 34 38
VBLEX 45IRE 39 43 47
DC restration gain Vdcrest85 V15 85 90 95 IRE
Vdcrest120 110 115 120
Vdcrest step 5 8 11
WPS Level VWPS V16 2.5 2.8 3.3 Vp-p
Chroma Trap Gain GTRAP358 V17 • -29 -25 dB
GTRAP443 • -27 -23
Half Tone reduction for Y GHTY V18 -6.5 -6 -5.5 dB

CHROMA STAGE
TEST TEST
ITEM SYMBOL MIN TYP MAX UNIT
CIRCUIT CINDITION
ACC Chara. •ACCL C1 • 25 40 mV p-p
•ACCH 600 1000 •
TOF Chara.(4.43) fo •0T443 C2 • 5.16 • MHz
Q •T443 • 1.86 • •
BPF Chara. (4.43) fo •0B443 • 4.45 • MHz
Q •B443 • 1.86 • •
TOF Chara. (3.58) fo •0T358 • 4.30 • MHz
Q •T358 • 1.92 • •
BPF Chara. (3.58) fo •0B358 • 3.67 • MHz
Q •B358 • 1.92 • •
595 700 805
C Delay Time (P/N) tCDELPN C3 600
ns
510 690
C Delay Time (SECAM) tCDELS 765 900 1035
Time Difference between Y / C •tY/C -60 0 60
Color Control Characteristics MAX •COLMAX C4 4.0 6.5 8.0 dB
MIN •COLMIN • • -20
Uni-Color Control Characteristics •UCCMIN C5 -27 -24 -21 dB
TINT Chara.(4.43NTSC) MAX ••443MAX C6 28 42 56 deg
MIN ••443MIN -28 -42 -56
TINT Chara.(3.58NTSC) MAX ••358MAX 28 42 56
MIN ••358MIN -28 -42 -56
Relative Amplitude (PAL) R/B VPR/B C7 0.47 0.57 0.67 •
G/B VPG/B 0.31 0.38 0.45
Relative Amplitude (NTSC1) R/B VNR/B 0.62 0.72 0.82
G/B VNG/B 0.26 0.32 0.38
Relative Amplitude (NTSC2) R/B VNR/B 0.70 0.80 0.90
G/B VNG/B 0.24 0.30 0.36
Relative Amplitude (DVD) R/B VNR/B 0.67 0.77 0.87
G/B VNG/B 0.36 0.44 0.52

Ver3.7 00/01/28 26




TEST TEST
ITEM SYMBOL MIN TYP MAX UNIT
CIRCUIT CINDITION
Relative Phase (PAL) R-B •PR-B C8 84 89 94 deg
G-B •PG-B 230 236 242
Relative Phase (NTSC1) R-B •N1R-B 83 89.5 95
G-B •N1G-B 232 241 248
Relative Phase (NTSC2) R-B •N2R-B 95 105 115
G-B •N2G-B 232 240 248
Relative Phase (DVD) R-B •DVDR-B 86 92.8 100
G-B •DVDG-B 236 245 254
APC Pull- In Range (4.43MHz) •4APCP+ C9 350 500 2500 Hz
•4APCP- 350 500 -2500
APC Hold Range (4.43MHz) •4APCH+ 350 500 2500
•4APCH- 350 500 -2500
APC Pull-In Range (3.58MHz) •3APCP+ 300 500 2500
•3APCP- 300 500 -2500
APC Hold Range (3.58MHz) •3APCH+ 300 500 2500
•3APCH- 300 500 -2500
APC Control Sensitivity (4.43MHz) •443 1.5 2.5 3.5 Hz/mV
C10
APC Control Sensitivity (3.58MHz) •358 0.6 1.1 1.6
PAL ID Sensitivity (Normal Mode) •PIDON C11 0.7 1.5 3 mVp-p
•PIDOFF 1.0 1.9 4
PAL ID Sensitivity (Low Mode) •PIDLON 1.7 3.4 6
•PIDLOFF 2.5 5.0 8
NTSC ID Sensitivity (Normal Mode) •NIDON 0.6 1.3 2.6
•NIDOFF 1.0 2.1 4.2
NTSC ID Sensitivity (Low Mode) •NIDLON 2.0 4 7
•NIDLOFF 4.0 8 12
CWOUT Amplitude •CW C12 0.35 0.5 0.65 V p-p
DC Bias at killer on V BCWKON 1.0 1.5 2.0 V
DC Bias at killer off VBCWKOFF 3.0 3.5 4.0
Half Tone Chara. for C •HTC C13 -6.7 -6.0 -5.3 dB
Sub-Color Control MAX •SCOLMAX C14 +2.5 +3.5 4.5 dB
Characteristics MIN •SCOLMIN -4.5 -3.5 -2.5
1H Delay Time TBDL • 64 •s
TRDL 64

SECAM STAGE
TEST TEST
ITEM SYMBOL MIN TYP MAX UNIT
CIRCUIT CINDITION
Bell Monitor Output Amplitude embo SE1 63 100 163 mV p-p
Bell Filter f0 f0B-C SE2 -23 0 23 kHz
Bell Filter f0 Variable Range f0B-VR SE3 15 30 45
Bell Filter Q QBEL SE4 13 15 17
Color Difference Output Amplitude VBS SE5 1.29 1.85 2.41 Vp-p
VRS 1.12 1.57 2.22
Color Difference Relative Amplitude R/B-S SE6 0.7 0.80 0.90 -
Color Difference S/N Ratio SNB-S SE8 -38 -34 -28 dB
SBR-S -44 -39 -32
Linearity LinB SE9 85 100 117 %
LinR 85 100 117
Rising-Fall Time trfB SE10 - 1.1 1.5 •s
trfR - 1.1 1.5
SECAM ID Sensitivity H •SIDHON SE11 0.66 1.32 2.64 mV
(Normal Mode) •SIDHOFF 1.82 3.64 6.5

Ver3.7 00/01/28 27




TEST TEST
ITEM SYMBOL MIN TYP MAX UNIT
CIRCUIT CINDITION
H+V •SIDHVON 0.6 1.20 2.4
•SIDHVOFF 1.0 1.9 3.8
SECAM ID Sensitivity H •SIDLHON 1.7 3.3 6.0
(Low Mode) •SIDLHOFF 4.5 9 14
H+V •SIDLHVON 1.1 2.2 4.4
•SIDLHVOFF 2.8 5.6 10
Gate Pulse Width Variable Range WGP+200 SE12 1.7 1.8 1.9 •s
WGP 1.9 2.0 2.1
WGP-200 2.1 2.2 2.3
SECAM black adjustment VSBMAX SE13 80 85 90 mV
characteristic VSRMAX 80 85 90
VSRMIN -97 -92 -87
VSRMIN -97 -92 -87
SECAM black adjustment sensitivity •VSB 12 14 16
•VSR 12 14 16

TEXT STAGE
TEST TEST
ITEM SYMBOL MIN TYP MAX UNIT
CIRCUIT CINDITION
V-BLK Pulse Output Level •VBLK 0.1 0.6 1.1
T1 V
H-BLK Pulse Output Level •HBLK 0.1 0.6 1.1
RGB Output Black Level (0IRE DC) •BLACK T2 2.25 2.5 2.75 V
RGB Output White Level (100IRE
•WHITE T3 • 2.50 • Vp-p
AC)
Cut-Off Voltage Variable Range •CUT+ T4 0.6 0.65 0.7 V
•CUT- -0.7 -0.65 -0.6
Drive Control Variable Range •DR+ T5 2.5 3.5 4.5 dB
•DR- -8.0 -5.5 -4.5
ABCL Control Voltage Range •ABCLH T6 5.7 6.0 6.3 V
•ABCLL 4.5 4.8 5.1
ACL Gain •ACL -21 -19 -17 dB
ABL Point •ABLP1 T7 -0.1 0 0.1 V
•ABLP2 -0.3 -0.2 -0.1
•ABLP3 -0.4 -0.3 -0.2
•ABLP4 -0.6 -0.5 -0.3
ABL Gain •ABLG1 T8 -0.31 -0.21 -0.11 V
•ABLG2 -0.48 -0.38 -0.28
•ABLG3 -0.60 -0.50 -0.40
•ABLG4 -0.77 -0.67 -0.57
Analog RGB Dynamic Range ••TX T9 0.7 - - Vp-p
Analog RGB Contrast Control MAX. •TXCMAX T10 0.59 0.74 0.94 Vp-p
Characteristic CEN. •TXCCEN 0.34 0.41 0.49
MIN. •TXCMIN 0.06 0.08 0.1
Analog RGB Brightness MAX. •TXBRMAX T11 2.8 3.25 3.7 Vp-p
Control Characteristic
•TXBRCEN 2.2 2.5 2.8
CEN.
MIN. •TXBRMIN 1.3 1.75 2.2
Analog RGB Mode Switching Level •YSHALF T12 3.3
•YSBLK 0.7 V
Analog RGB Mode Transfer ••YS T13 • 40 100 ns
Characteristic t••YS • 40 100
••YS • 40 100
t••YS • 40 100
Half Tone Mode Switching Level •HT T14 0.7 V
Cross Talk from Analog RGB to•• ••TX-TV T15 • -55 -40 dB
Cross Talk from •• to Analog RGB• ••TV-TX T16 • -55 -40 dB

Ver3.7 00/01/28 28




TEST TEST
ITEM SYMBOL MIN TYP MAX UNIT
CIRCUIT CINDITION
Baseband TINT Characteristic ••BBMAX T17 7 12 17 deg
••BBMIN -7 -12 -17
Analog RGB / RGB Output Voltage •VR-G T18 -40 40 mV
Axes Difference •VG-B -40 40
•VB-R -40 40

DEF STAGE
TEST TEST
ITEM SYMBOL MIN TYP MAX UNIT
CIRCUIT CINDITION
AFC Inactive Period 50Hz •50AFCOFF •• • 308-7 • H
60Hz •60AFCOFF • 260-10 •
H-OUT Start Voltage •HON •• 4.7 5.0 5.3 •
H-OUT Pulse Duty •HOUT •• 38.5 40.5 42.5 •
H-OUT Freq. On AFC Stop Mode •HAFCOFF •• 15.585 15.734 15.885 kHz
Horizontal Free-Run Frequency 50Hz •H50FR •• 15.475 15.625 15.775 kHz
60Hz •H60FR 15.585 15.734 15.885
Horizontal Freq. Variable MAX. •HMAX •• 16.200 16.400 16.600 kHz
Range MIN. •HMIN 14.600 14.900 15.200
Horizontal Freq. Control Sensitivity •HAFC •• 1.3 1.8 2.3 Hz/mV
Horizontal Pull-In Range •HPH •• 500 • • Hz
•HPL 500 • •
H-OUT Voltage •HOUTH •• 4.0 4.4 4.8 V
•HOUT • 0.15 0.30
Horizontal Freq. Dependence on •cc ••HVCC ••• -20 0 20 Hz/V
FBP Phase ••FBP ••• 2.7 3.2 3.7 •s
H-Sync. Phase ••HSYNC 0.2 0.3 0.4
Horizontal Position Variable Range •••HPOS ••• 6.3 6.8 7.3 •s
AFC-2 Pulse Threshold Level •AFC2 ••• 3.3 3.6 3.9 V
H-BLK Pulse Threshold Level •HBLK ••• 0.8 1.3 1.6
BLACK Peak Det. Stop Period (H) •HBPDET ••• 7.5 8.0 8.5 •s
•BPDET 13.5 14.0 14.5
Gate Pulse Start Phase ••GP ••6 2.8 3.0 3.2 •s
Gate Pulse Width •GP 1.8 2.0 2.2
Vertical Oscillation Start Voltage •VON ••7 4.7 5.0 5.3 V
Vertical Free-Run Frequency Auto50 •VAUFR50 •18 45 50 55 Hz
Auto60 •VAUFR60 55 60 65
50Hz •V50FR 45 50 55
60Hz •V60FR 55 60 65
Gate Pulse V-Masking Period 50Hz •50GPM •19 • 308-7 • H
60Hz •60GPM • 260-10 •
V.Ramp DC on Service Mode •NOVRAMP •20 3.0 3.2 3.4 V
Vertical Pull-In Range (Auto) •VPAUL •21 • 224.5 • H
•VPAUH • 343.5 •
Vertical Pull-In Range (50Hz) FVP50L 274.5
FVP50H 343.5
Vertical Pull-In Range (60Hz) •VP60L • 224.5 •
•VP60H • 293.5 •
Vertical Period on Fixed Mode TV312.5 •22 312.5 H
TV262.5 262.5
TV313 313
•V263 • 263 •
V-BLK Start Phase 50Hz ••50VBLK •23 27 29 31 •s
60Hz ••60VBLK 27 29 31
V-BLK Width 50Hz •50VBLK • 22 • H
60Hz •60VBLK • 18 •

Ver3.7 00/01/28 29




TEST TEST
ITEM SYMBOL MIN TYP MAX UNIT
CIRCUIT CINDITION
Sand Castle Pulse Level •SCPH •24 6.70 7.00 7.30 V
•SCPM 4.60 4.90 5.20
•SCPL 1.55 1.85 2.15
Vertical Ramp Amplitude •VRAMP •25 1.50 1.67 1.83 Vp-p
Vertical AMP Gain •VAMP •26 18 22 26 dB
Vertical AMP MAX. Output Level •VOMAX 1.8 2.3 2.8 V
Vertical AMP Min. Output Level •VOMIN • 0.0 0.3
Vertical AMP Max. Output Current •VOMAX •27 11 15 19 mA
Vertical NFB Amplitude •NFB •28 1.74 1.90 2.06 Vp-p
Vertical Amplitude Variable Range ••VRAMPH 43 47 51 %
••VRAMPL -51 -47 -43
Vertical Linearity Variable Range ••LIN1+ •29 -23 -21 -18 %
••LIN1- 21 24 27
••LIN2+ 17 20 23
••LIN2- -28 -25 -22
Vertical S Correction Variable Range ••S1+ •30 -26 -23 -20 %
••S1- 21 24 27
••S2+ -26 -23 -20
••S2- 21 24 27
Vertical Guard Voltage •VG •31 1.80 2.00 2.20 V

Ver3.7 00/01/28 30




TEST CONDITION

PIF STAGE
Note Items/Symbols Bus conditions Measurement methods
P1 PIF Input Sensitivity RF AGC:except 0 (1)Input a signal that 38.9[MHz], 90[dBV], and 30 [%] modulated
/ vin min(p) PIF Freq. : by 15 [kHz] sine wave at pin 6.
38.9MHz (2)Set the bit of “VCO Adj. Req.” to “1”, and set the bit of “VCO Adj.
PIF maximum input
VCO Adj. Center Req.” to “0”.
signal :• (3)Measure the amplitude at Pin 54(vo#54 [Vp-p]).
/ vin max(p) 0/1 (4)Decreasing the IF input level, measure the input level at which
PIF gain control range Others : Preset the output amplitude at pin 54 turns to be –3dB against “vo#54”
/ RAGC(p) (vin min(p)[dBV]).
(5)Increasing the IF input level, measure the input level at which
the output amplitude at pin 54 turns to be -1dB against “vo#54”
(vin min(p)[dBV]).
(6)RAGC(p)[dB] = vin max(p) - vin min(p)

P2 RF AGC output RF (1)Input a 38.9[MHz], 90[dBV] signal at pin 6.

voltage AGC•:•Adjust (2)Set the bit of “VCO Adj. Req.” to “1”, and set the bit of “VCO Adj.
/ VAGC max PIF Freq. : Req.” to “0”.
/ VAGC min 38.9MHz (3)Adjust RF AGC so that the pin 9 voltage is 4.5V.
VCO Adj. Req.: (4)Increase the IF input level to 107dBuV.
•0/1 (5)Measure the pin 9 voltage (VAGC min[V]).
Others : Preset (6)Connect pin 6 and pin 7 to GND.
(7)Measure the pin 9 voltage (VAGC max[V]).
P3 RF delay point RF (1)Input a 38.9[MHz], 90[dBV] signal at pin 6.
/ v Dly min AGC•:•Adjust (2)Set the bit of “VCO Adj. Req.” to “1”, and set the bit of “VCO Adj.
/ v Dly max PIF Freq. Req.” to “0”.
38.9MHz (3)Set the data of “RF AGC” to 01(h).
VCO Adj. Req. : (4)Decrease the IF input level, measure the input level at which the
•0/1 voltage at pin 9 turn to be 4.5[V] (v Dly min[dBV]).
RF AGC: 01/3F (5)Set the data of “RF AGC” to 3F(h).
Others : Preset (6)Increase the IF input level, measure the input level at which the
voltage at pin 9 turn to be 4.5[V] (v Dly max[dBV]).
P4 PIF input resistance Preset (1)Remove all connection from pin 6 and pin 7.
/ Zin R(p) (2)Measure the resistance (Zin R(p)[k]) and capacitance (Zin
C(p)[pF]) of pin 6 and pin 7 by the impedance meter.
PIF input capacitance
/ Zin C(p)
P5 Differential Gain RF AGC:except 0 (1)Input a signal that 38.9[MHz], 90[dBV], and 87.5 [%] modulated
/ DG PIF Freq.: by 10 stair video signal at pin 6.
38.9MHz (2)Set the bit of “VCO Adj. Req.” to “1”, and set the bit of “VCO Adj.
Differential Phase VCO Adj. Req.: Req.” to “0”.
/ DP 0/1 (3)Measure "DG[%]" and "DP[deg]" for Pin54 output.
Vi Pol:0/1
Others : Preset
P6 Intermodulation RF AGC:except 0 (1)Input a signal composed of following 3 signals at pin 6;
/ IM PIF Freq. : 38.90[MHz]/90[dBV],
38.9MHz 34.47[MHz]/80dBV]
VCO Adj. Req.: 33.40[MHz]/80[dBV]
0/1 (2)Set the bit of “VCO Adj. Req.” to “1”, and set the bit of “VCO Adj.
Others : Preset Req.” to “0”.
(3)Adjust pin 10 voltage so that the bottom of pin 54 output is equal
to sync. tip level.
(4)Measure the 1.07[MHz] level against the 4.43[MHz] level(=0[dB])
(IM[dB]).

Ver3.7 00/01/28 31




Note Items/Symbols Bus conditions Measurement methods

P7 Video output signal RF AGC:except 0 (1)Input a signal that 38.9[MHz], 90[dBV], and 87.5 [%] negative
amplitude PIF Freq. : modulated by 100% white video signal at pin 6.
/ vDet(p)n 38.9MHz (2)Set the bit of “VCO Adj. Req.” to “1”, and set the bit of “VCO Adj.
/ vDet(p)p VCO Adj. Req. : Req.” to “0”.
0/1 (3)Set the bit of “L-SECAM MODE” to “0”.
L-SECAM MODE (4)Measure the amplitude of the pin 54 output signal (vDet(p)n[Vp-
:0/1 p]).
Others : Preset (5)Input a signal that 38.9[MHz], 90[dBV], and 97 [%] positive
modulated by 100% white video signal at pin 6.
(6)Set the bit of “L-SECAM MODE” to “1”.
(7)Measure the amplitude of the pin 54 output signal (vDet(p)p[Vp-
p]).
P8 Video output S/N RF AGC:except 0 (1)Input a signal that 38.9[MHz], 90[dBV], and 87.5 [%] modulated
/ S/N(p) PIF Freq. : by black video signal at pin 6.
38.9MHz (2)Set the bit of “VCO Adj. Req.” to “1”, and set the bit of “VCO Adj.
VCO Adj. Req. : Req.” to “0”.
0/1 (3)Measure the video S/N for pin 54 output (HPF : 100[kHz], LPF :
Others : Preset 5[MHz], CCIR weighted) (S/N(p)[dB]).
P9 Synchronous signal RF AGC:except 0 (1)Input a signal that 38.9[MHz], 90[dBV], 87.5[%] negative
level PIF Freq. : modulated by 100% white signal at pin 6.
/ Vsync n 38.9MHz (2)Set the bit of “VCO Adj. Req.” to “1”, and set the bit of “VCO Adj.
/ Vsync p VCO Adj. Req.: Req.” to “0”.
0/1 (3)Set the bit of “L-SECAM MODE” to “0”.
L-SECAM MODE (4)Measure the voltage of the sync. tip at pin 54 (Vsync n[V]).
:0/1 (5)Input a signal that 38.9[MHz], 90[dBV], and 97 [%] positive
Others : Preset modulated by 100% white video signal at pin 6.
(6)Set the bit of “L-SECAM MODE” to “1”.
(7)Measure the voltage of the sync. tip at pin 54 (Vsync p[V]).
P10 Video bandwidth RF AGC:except 0 (1)Input the mixture of 2 signals (signal1 : 38.9[MHz]/82[dBV],
(-3dB) PIF Freq.: signal 2 : 38.8[MHz]/69[dBV]) to pin 6.
/ fDet(p) 38.9MHz (2)Set the bit of “VCO Adj. Req.” to “1”, and set the bit of “VCO Adj.
VCO Adj. Req.: Req.” to “0”.
0/1 (3)Measure the minimum voltage of the output signal at pin 54
L-SECAM MODE (Vo#54).
:0/1 (4)Apply the DC voltage to pin 10 and adjust it so that the minimum
Others : Preset voltage of the output signal at pin 54 is equal to Vo#54.
(5)Decrease frequency of the input signal 2 at pin 6, and measure
amplitude of the output signal at pin 54.
(6)Measure fDet(p) shown as below.
amplitude at pin 54

3[dB]
Ref.level
Output

100[kHz] f Det(p)
Frequency of
the output signal at pin54

Ver3.7 00/01/28 32




Note Items/Symbols Bus conditions Measurement methods

P11 Capture range of the RF AGC : except (1)Input a signal that 38.9[MHz], 90[dBV] at pin 6.
PLL 0 (2)Set the bit of “VCO Adj. Req.” to “1”, and set the bit of “VCO Adj.
PIF Freq. : Req.” to “0”.
/ fpH(p)
38.9MHz (3)Sweep down the input signal frequency to 34.9[MHz], and
/ fpL(p) VCO Adj. Req. : sweep up to 43.9[MHz]. Sweep down the input signal frequency
Hold range of the PLL 0/1 to 38.9[MHz].
/ fhH(p) Others : Preset (4)Measure the voltage at pin 55 and measure the frequency of the
/ fhL(p) input signal shown as below.

Voltage of pin 55
f h(p)L f p(p)L

38.9[MHz]
f p(p)H f h(p)H
Frequency of
the input signal

P12 Control steepness of PIF Freq. : (1) Set the bit of “VCO Adj. Req.” to “1”, and set the bit of “VCO
the VCO 38.9MHz Adj. Req.” to “0”.
/ VCO Adj. Req. : (2) Set the FET probe which connected to the spectrum analyzer
0/1 near by pin 50 or pin 51 (Don’t touch the probe directly to pin 50
Others : Preset or to pin 51).
(3) Apply 2.3[V] to pin 47, and measure frequency of the VCO
oscillation by the spectrum analyzer (fLVCO[MHz]).
(4) Apply 2.7[V] to pin 47, and measure frequency of the VCO
oscillation by the spectrum analyzer (fHVCO[MHz]).
(5) [MHz/V] = (fHVCO-fLVCO)/0.4
P13 Steepness of the AFT PIF Freq. : (1) Input a 38.9[MHz], 90[dBV] signal at pin 6.
detection 38.9MHz (2) Set the bit of “VCO Adj. Req.” to “1”, and set the bit of “VCO
/ S AFT VCO Adj. Req.: Adj. Req.” to “0”.
AFT Voltage 0/1 (3) Input a 38.9[MHz]-20[kHz], 90[dB V], non-modulation signal at
/ VAFTmax Others : Preset pin 6.
/ VAFTmin (4) Measure the voltage at pin 55 (VH#55[V]).
(5) Input a 38.9[MHz]+20[kHz], 90[dBV], non-modulation signal
at pin 6.
(6) Measure the voltage at pin 55 (VL#55[V]).
(7) S AFT[kHz/V] = 40/(VH#55-VL#55)
(8) Input a 38.9[MHz]-500[kHz], 90[dBV], non-modulation signal
at pin 6.
(9) Measure the voltage at pin 55 (VAFTmax[V]).
(10) Input a 38.9[MHz]+500[kHz], 90[dBV], non-modulation signal
at pin 6.
(11) Measure the voltage at pin 55 (VAFTmin[V]).
P14 AFT output voltage on Preset (1)Measure the voltage at pin 55 (VAFT Def[V]).
defeating

Ver3.7 00/01/28 33




SIF STAGE
Note Items/Symbols Bus conditions Measurement methods
S1 Limiting sensitivity SIF-Freq. : (1) Set the bits of “SIF-Freq.” to “11”.
/ vin lim(s)4.5MH 4.5M/5.5M/6.0M/ (2) Input a signal that 4.5[MHz], 100[dBV], 25[kHz] deviated by
/ vin lim(s)4.5ML 6.5M 400[Hz] sine wave at pin 56.
/ vin lim(s)5.5M AUDIO ATT : 127 (3) Measure the amplitude at pin 4 (vo#4[mVrms]).
/ vin lim(s)6.0M Others : Preset (4) Decreasing the 4.5[MHz] signal level, measure the 4.5[MHz]
/ vin lim(s)6.5M signal level at which the amplitude at pin 4 turns to be –3[dB]
against “vo#4” (vin lim(s)4.5MH[dBV]).
(5) Input a signal that 4.5[MHz], 100[dBV], 25[kHz] deviated by
400[Hz] sine wave at pin 56.
(6) Do same measuring as above (3)~(4) (vin lim(s)4.5ML).
(7) Set the bits of “SIF-Freq.” to “00”.
(8) Change the frequency of the input signal to 5.5MHz, and
change the deviation of the input signal to 50[kHz].
(9) Do same measuring as above (3)~(4) (vin lim(s)5.5M).
(10) Set the bits of “SIF-Freq.” to “01”.
(11) Change the frequency of the input signal to 6.0MHz, and do
same measuring as above (3)~(4) (vin lim(s)6.0M).
(12) Set the bits of “SIF-Freq.” to “10”.
(13) Change the frequency of the input signal to 6.5MHz, and do
same measuring as above (3)~(4) (vin lim(s)6.5M).
S2 AM reduction ratio SIF-Freq. : (1) Set the bits of “SIF-Freq.” to “11”.
/ AMR4.5MH 4.5M/5.5M/6.0M/ (2) Input a signal that 4.5[MHz], 100[dBV], 25[kHz] deviated by
/ AMR4.5ML 6.5M 400[Hz] sine wave at pin 56.
/ AMR5.5M AUDIO ATT : 127 (3) Measure the amplitude at pin 4 (vo#4[mVrms]).
/ AMR6.0M Others : Preset (4) Input a signal that 4.5[MHz], 100[dBV], and 30 [%] modulated
/ AMR6.5M by 400 [Hz] sine wave at pin 56.
(5) Measure the amplitude at pin 4 (v#4[mVrms]).
(6) AMR4.5H[dB] = 20log(v#4/ vo#4)
(7) Input a signal that 4.5[MHz], 100[dBV], 25[kHz] deviated by
400[Hz] sine wave at pin 56.
(8) Do same measuring as above (3)~(6) (AMR4.5ML).
(9) Set the bits of “SIF-Freq.” to “00”.
(10) Change the frequency of the input signals to 5.5MHz, and
change the deviation of the input signal to 50[kHz].
(11) Do same measuring as above (3)~(6) (AMR5.5M).
(12) Set the bits of “SIF-Freq.” to “01”.
(13) Change the frequency of the input signals to 6.0MHz, and do
same measuring as above (3)~(6) (AMR6.0M).
(14) Set the bits of “SIF-Freq.” to “10”.
(15) Change the frequency of the input signals to 6.5MHz, and do
same measuring as above (3)~(6) (AMR6.5M).

S3 AF output signal SIF-Freq. : 4.5M (1)Input a signal that 4.5[MHz], 100[dBV], 25[kHz] deviated by
amplitude AUDIO ATT : 127 1[kHz] sine wave at pin 56.
Others : Preset (2)Measure the amplitude at pin 4 (vDet(s)4.5MH[mVrms]).
/ vDet(s)4.5MH
(3)Measure the total harmonics distortion at pin 4 (THD4.5MH[%]).
AF output S/N (4)Input a 4.5[MHz], 100[dBV] signal at pin 56.
/ S/N(s)4.5MH (5)Measure the amplitude at pin 4 (vn(s)[mVrms]).
Total harmonics (6)S/N4.5MH[dB] = 20log(vDet(s)/vn(s))
distortion
/ THD4.5MH
S4 AF output signal SIF-Freq. : 4.5M (1)Input a signal that 4.5[MHz], 100[dBV], 25[kHz] deviated by
amplitude AUDIO ATT : 127 1[kHz] sine wave at pin 56.
Others : Preset (2)Do same measuring as vDet(s)4.5MH et al. (vDet(s)4.5ML,
/ vDet(s)4.5ML
S/N(s)4.5ML, THD4.5ML).
AF output S/N
/ S/N(s)4.5ML
Total harmonics
distortion
/ THD4.5ML

Ver3.7 00/01/28 34




Note Items/Symbols Bus conditions Measurement methods

S5 AF output signal SIF-Freq. :5.5M (1)Input a signal that 5.5[MHz], 100[dBV], 50[kHz] deviated by
amplitude AUDIO ATT : 127 400[Hz] sine wave at pin 56.
Others : Preset (2)Do same measuring as vDet(s)4.5MH et al. (vDet(s)5.5M,
/ vDet(s)5.5M
S/N(s)5.5M, THD5.5M).
AF output S/N
/ S/N(s)5.5M
Total harmonics
distortion
/ THD5.5M
S6 AF output signal SIF-Freq. : 6.0M (1)Input a signal that 6.0[MHz], 100[dBV], 50[kHz] deviated by
amplitude AUDIO ATT : 127 400[Hz] sine wave at pin 56.
Others : Preset (2)Do same measuring as vDet(s)4.5MH et al. (vDet(s)6.0M,
/ vDet(s)6.0M
S/N(s)6.0M, THD6.0M).
AF output S/N
/ S/N(s)6.0M
Total harmonics
distortion
/ THD6.0M
S7 AF output signal SIF-Freq. : 6.5M (1)Input a signal that 6.5[MHz], 100[dBV], 50[kHz] deviated by
amplitude AUDIO ATT : 127 400[Hz] sine wave at pin 56.
Others : Preset (2)Do same measuring as vDet(s)4.5MH et al. (vDet(s)6.5M,
/ vDet(s)6.5M
S/N(s)6.5M, THD6.5M).
AF output S/N
/ S/N(s)6.5M
Total harmonics
distortion
/ THD6.5M
S8 Demodulation band SIF-Freq. : 4.5M (1)Input a signal that 4.5[MHz], 100[dBV], 25[kHz] deviated by
width of the FM AUDIO ATT : 127 400[Hz] sine wave at pin 56.
demodulator Others : Preset (2)Measure the amplitude at pin 4(vo#4 [Vp-p]).
/ fpH(s)1 (3)Increase the input signal frequency, measure the input signal
/ fpL(s)1 frequency at which the output amplitude at pin 4 turn to be -
3[dB] against “vo#4” (fpH(s)1[MHz])
(4)Decrease the input signal frequency, measure the input signal
frequency at which the output amplitude at pin 4 turn to be -
3[dB] against “vo#4” (fpL(s)1[MHz])
S9 Demodulation band SIF-Freq. : 5.5M (1)Input a signal that 5.5[MHz], 100[dBV], 50[kHz] deviated by
width of the FM AUDIO ATT : 127 400[Hz] sine wave at pin 56.
demodulator Others : Preset (2)Measure the amplitude at pin 4(vo#4 [Vp-p]).
/ fpH(s)2 (3)Increase the input signal frequency, measure the input signal
/ fpL(s)2 frequency at which the output amplitude at pin 4 turn to be -
3[dB] against “vo#4” (fpH(s)2[MHz])
(4)Decrease the input signal frequency, measure the input signal
frequency at which the output amplitude at pin 4 turn to be -
3[dB] against “vo#4” (fpL(s)2[MHz])
S10 Audio attenuater gain AUDIO-SW : 1 (1) Input a 400[Hz], 927[mVrms] sine wave at pin 53.
/ G att max AUDIO ATT : (2) Set the “AUDIO ATT” data to “127”.
/ G att mid 0/64/127 (3) Measure the amplitude at pin 4 (v#4max[mVrms]).
/ G att min Others : Preset (4) G att max[dB] = 20log(v#4max/927)
(5) Set the “AUDIO ATT” data to “64”.
(6) Measure the amplitude at pin 4 (v#4mid[mVrms]).
(7) G att mid[dB] = 20log(v#4mid/927)
(8) Set the “AUDIO ATT” data to “0”.
(9) Measure the amplitude at pin 4 (v#4min[mVrms]).
(10) G att min[dB] = 20log(v#4min/927)
S11 Audio attenuater off- AUDIO-SW : 1 (1) Connect pin 53 to GND through a 4.7[F] capacitor.
set AUDIO ATT : (2) Set the “AUDIO ATT” data to “127”.
/ Vos att 0/127 (3) Measure the DC voltage at pin 4 (V#4max[mV]).
Other : Preset (4) Set the “AUDIO ATT” data to “0”.
(5) Measure the DC voltage at pin 4 (V#4min[mV]).
(6) Vos[mV] = V#4min-V#4max

Ver3.7 00/01/28 35




Note Items/Symbols Bus conditions Measurement methods

S12 Audio switch cross- SIF-Freq. : 5.5M (1) Input a signal that 5.5[MHz], 100[dBV], 50[kHz] deviated by
talk AUDIO-SW : 0/1 1[kHz] sine wave at pin 56.
/ CT(s)T-E AUDIO ATT : 127 (2) Connect pin 53 to GND through a 4.7[F] capacitor.
/ CT(s)E-T Other : Preset (3) Measure level of the 1[kHz] at pin 4 (v#4T1[dBV]).
(4) Set the bit of “AUDIO-SW” to “1”.
(5) Measure level of the 1[kHz] at pin 4 (v#4E1[dBV]).
(6) CT(s)T-E[dB] = v#4E1-v#4T1
(7) Input a 5.5[MHz], 100[dBV] signal at pin 56.
(8) Measure level of the 1[kHz] at pin 4 (v#4E2[dBV]).
(9) Input a 1[kHz], 927[mVrms] signal at pin 53.
(10) Set the bit of “AUDIO-SW” to “0”.
(11) Measure level of the 1[kHz] at pin 4 (v#4T2[dBV]).
(12) CT(s)E-T[dB] = v#4T2-v#4E2
S13 Audio switch off-set SIF-Freq. : 5.5M (1) Input a 5.5[MHz], 100[dBV] signal at pin 56.
/ Vos sw AUDIO-SW : 0/1 (2) Connect pin 53 to GND through a 4.7[F] capacitor.
AUDIO ATT : 127 (3) Set the bit of “AUDIO-SW” to “0”.
Other : Preset (4) Measure the voltage at pin 4 (V#4T[V]).
(5) Set the bit of “AUDIO-SW” to “1”.
(6) Measure the voltage at pin 4 (V#E[V]).
(7) Vos sw[V] = V#4E-V#4T

Ver3.7 00/01/28 36




VIDEO stage (RGB Mute:0 / R cut off:127 / DC rest.:10)

Note Items/Symbols Bus conditoins Measurement methods
V1 TV Input Dynamic Video SW:00/01 (1)Input a white signal with sync into Pin46(EXT IN)&48(TV IN).
Range Others:Preset (2)Increasing the input amplitude, measure the amplitude(include
sync) at
/ DRTV
which the Pin41(MON OUT) output is clipped, that is
External Input "DRTV"(Video SW:00) / "DREXT"(Video SW:01).
Dynamic Range
/ DREXT
V2 TV Mode Gain Video SW:00/01 (1)Input a 1Vp-p, white signal with sync into Pin46(EXT
/ GTV Others:Preset IN)&48(TV IN).
(2)Set Video SW to 00 and measure the gain between PIN48 and
Ext. Mode Gain
Pin41(MON OUT), that is "GTV".
/ GEXT (3)Set Video SW to 01 and measure the gain between Pin46 and
Pin41, that is "GEXT".
V3 AV SW Cross-Talk Video SW:00/01 (1)Input a PAL red signal with sync into Pin48(TV IN) and
/ CTSWTE Others:Preset connect Pin46(EXT IN) to GND via a 1uF capacitor.
/ CTSWET (2)Set Video SW 01, measure the amplitude of 4.43MHz signal at
Pin41 and calculate the cross-talk, that is "CTSWTE".
(3)Input a PAL red signal with sync into Pin46 and connect Pin48
to GND via a 1uF capacitor.
(4)Set Video SW 00, measure the the amplitude of 4.43MHz
signal at Pin41 and calculate the cross-talk, that is "CTSWET".
V4 Y Input Dynamic WPS:1 (1)Input a white signal with sync into Pin38&39.
Range Uni-Color:63 (2)Increasing the Pin39 input amplitude, measure the amplitude
/ DRY Brightness:0 (includesync) at which the Pin20 output is clipped, that is
Color:0 "DRY".
RGB Mute:0
R cut off:63
DC rest.:10
Others:Preset
V5 Y Input Pedestal RGB Mute:0 (1)Input a composite sync signal into Pin38.
Clamp Voltage R cut off:63 (2)Connect Pin39 to GND via a 1uF capacitor.
/ VYCLP DC rest.:10 (3)Measure the DC Voltage at Pin39, that is "VYCLP".
Others:Preset
V6 Y Frequency RGB Mute:0 (1)Input a 0.5Vp-p sweep signal with sync into Pin38&39.
Response R cut off:63 (2)Adjust Sharpness so that the output amplitude for FSHP
/ FRY DC rest.:10 equals VSH100k.
Uni-Color:127 (3)Measure the frequency at which the output amplitude is 3dB
Sharpness:Adjust down
Color:0 against VSH100k, which is "FRY".
Others:Preset
V7 Y Delay Time Uni-Color:127 (1)Input a 2T pulse with sync into Pin38&39.
/ tYDEL Color:0 (2)Set the BUS data so that Y DL is 0ns(001).Observe the Pin20
/ •tYDEL-40 Y DL:000/001/111 output, measure the delay time between Pin39 and Pin20, that
/ •tYDEL+240 RGB Mute:0 is "tYDEL".
/ •tYDEL R cut off:63 (3)Set the BUS data so that Y DL is –40ns(000). Observe the
DC rest.:10 Pin20 output, measure the delay time between Pin39 and
Others:Preset Pin20, that is tYDEL-40.
(4) Set the BUS data so that Y DL is +240ns(111). Observe the
Pin20 output, measure the delay time between Pin39 and
Pin20, that is tYDEL+240.
(5)Calculate, “•tYDEL-40”= tYDEL-40 - "tYDEL"
“•tYDEL+240”= tYDEL+240 - "tYDEL"
“•tYDEL”= (“•tYDEL+240”- “•tYDEL-40”)/7

V8 Brightness Brightness: (1)Input a 0IRE black signal with sync into Pin38&39.
Characteristics 0/64/127 (2)Measure the DC level of picture period at Pin20 for
Color:0 Brightness:127/64/0,
/ VBRTMAX
RGB Mute:0 that is "VBRTMAX" / "VBRTCEN" / "VBRTMIN".
/ VBRTCEN R cut off:63 (3)Calculate;"•VBRT"=(VBRTMAX-VBRTMIN)/127
/ VBRTMIN DC rest.:10
Others:Preset
Brightness Data
Sensitivity
/ •VBRT

Ver3.7 00/01/28 37




Note Items/Symbols Bus conditoins Measurement methods

V9 Uni-Color Uni- (1)Input a 50IRE white signal with sync into Pin38&39.
Characteristics for Y Color:0/64/127 (2)Measure the output picture amplitude at Pin20 for Uni-
/ GUCYMAX Color:0 Color:127/64/0, that is VUCYMAX / VUCYCEN / VUCYMIN.
/ GUCYCEN RGB Mute:0 (3)Calculate; "GUCYMAX"=20*log(VUCYMAX/0.357)"
/ GUCYMIN R cut off:63 "GUCYCEN"=20*log(VUCYCEN/0.357)
DC rest.:10 "GUCYMIN"=20*log(VUCYMIN/0.357)
Others:Preset
V10 Sub-Contrast Sub-Contrast: (1)Input a 50IRE white signal with sync into Pin38&39.
Characteristics 0/8/15 (2)Measure the output picture amplitude at Pin20 for Sub-
/ GSCONMAX Uni-Color:127 Contrast 15/8/0,
/ GSCONMIN Color:0 that is VSCONMAX / VSCONCEN / VSCONMIN.
RGB Mute:0 (3)Calculate; "GSCONMAX"=20*log(VSCONMAX/VSCONCEN)
R cut off:63 "GSCONMIN"=20*log(VSCONMIN/VSCONCEN)
DC rest.:10
Others:Preset
V11 Sharpness Peaking Sharpness:63 (1)Input a 0.5Vp-p sweep signal with sync into Pin38&39.
Frequency Uni-Color:127 (2)Measure the frequency at which the Pin20 output amplitude is
/ FSHP Color:0 Max., that is "FSHP".
RGB Mute:0
R cut off:63
DC rest.:10
Others:Preset
V12 Sharpness Control Sharpness:0/32/6 (1)Input a 0.5Vp-p sweep signal with sync into Pin38&39.
Characteristics 3 Uni-Color:127 (2)Measure the output picture amplitude for 100kHz at Pin20, that
/ GSHMAX Color:0 is VSH100k.
/ GSHCEN RGB Mute:0 (3)Measure the output picture amplitude for FSHP when
/ GSHMIN R cut off:63 Sharpness is max.,center and min., that is VSHMAX, VSHCEN and
DC rest.:10 VSHMIN.
Others:Preset (4)Calculate; "GSHMAX"=20*log(VSHMAX/VSH100k)
"GSHCEN"=20*log(VSHCEN/VSH100k)
"GSHMIN"=20*log(VSHMIN/VSH100k)
V13 Y • correction start Uni-Color:127 (1)Input a gray raster with sync to Pin38&39.
point Color:0 (2)Set BUS data so that • point is 90IRE.
RGB Mute:0 (3)Increasing a video amplitude of input from 50IRE, measure a
/ VY• 70
R cut off:63 video ampitude as the figure below, that is “VY• 90”
/ VY• 80 DC rest.:10 (4)Set BUS data so that • point is 80IRE.And repeat (3), that is
/ VY• 90 • point:01/10/11 “VY• 80”.
Others:Preset (5)Set BUS data so that • point is 70IRE.And repeat (3), that is
“VY• 70”.
Y • correction curve (6)From the measurement in the above, find gain of the portion
/ GY• that the • correction has an effect on.
#20
output
Y ƒÁ=off

Y ƒÁ=90/80/70IRE

VYƒÁ90 #39 input

Ver3.7 00/01/28 38




Note Items/Symbols Bus conditoins Measurement methods

V14 Black Expansion Start Uni-Color:127 (1)Input a gray raster with sync to Pin38&39.
Point Color:0 (2)Set black stretch to 25IRE.
/ VBLEX25 Black (3)Decreasing Y amplitude of input from 50IRE, measure a Y
/ VBLEX35 stretch:00/01 amplitude as the figure below, that is “VBLEX25”
/ VBLEX45 /10/11 (4)Set black stretch to 35IRE/45IRE.
RGB Mute:0 (5)Repeat (3), that is ‘VBLEX35”, “VBLEX45”. below, that is “VY• 90”
Black Expansion AMP R cut off:63 (6)Find gain of the portion that the black stretch has an effect on.
Gain DC rest.:10 #20
output
/ GBLEX Others:Preset

Black
stretch 25/35/45IRE
=off

VBLEX25 #39 input

V16 DC Restration Gain Uni-Color:127 (1)Input a 100IRE signal with sync into Pin38&39.
/ VDcrest120 Color:0 (2)Set DC rest. to 10.
/ VDcrest90 Black (3)Measure a Y amplitude of pin20 output, that is V100.
/ VDcrest step stretch:00/01 (4)Set DC rest to 00.
/10/11 (5)Measure a Y amplitude of pin20 output, that is V120.
RGB Mute:0 (6)Calculate, “Vdcrest120” =(V120/V100)×100
R cut off:63 (7)Set DC rest to 11.
DC rest.:10 (8)Repeat (5)&(6), that is “VDcrest90”.
Others:Preset (9)Calculate, “VDcrest step”=(Vdcrest120 - VDcrest90)/4
V17 WPS Level Uni-Color:127 (1)Input a 120IRE ramp signal with sync into Pin38&39.
/ VWPS Brightness:127 (2)Measure the amplitude from cut-off level to peak(at which
Color:0 output signal is clipped), that is "VWPS".
RGB Mute:0
R cut off:63
DC rest.:10
Others:Preset
V18 Chroma Trap Gain C-Trap:0/1 (1)Input a 0.5Vp-p, 3.58MHz signal with sync into Pin43&39.
/ GTRAP Uni-Color:127 (2)Measure the 3.58MHz amplitude at PIn20 for Chroma
Color:0 Trap:1/0, that is VTRAPON / VTRAPOFF.
RGB Mute:0 (3)Calculate;"GTRAP"=20*log(VTRAPON/VTRAPOFF)
R cut off:63
DC rest.:10
Others:Preset
V19 Half Tone Ysm Mode:0 (1)Input a 100IRE white signal with sync into Pin38&39.
Characteristics for Y Uni-Color:127 (2)Measure the output picture amplitude at PIn20 , that is
/ GHTY Color:0 VHTYOFF.
RGB Mute:0 (3)Suppry Pin15 2V.
R cut off:63 (4) Measure the output picture amplitude at PIn20 , that is VHTYON
DC rest.:10 .
Others:Preset (3)Calculate;"GHTY"=20*log(VHTYON/VHTYOFF)

Ver3.7 00/01/28 39




CHROMA STAGE (RGB Mute:0 / RGB cut off:63 / DC rest.:10)

Note Items/Symbols Bus conditoins Measurement methods
C1 ACC Characteristics RGB Mute:0 (1)Input a 4.43MHz PAL rainbow color-bar(300mVp-p,
/ VACCH Y Mute:1 burst:chroma=1:1) with sync into Pin38&43.
/ VACCL Uni-Color:127 (2)Changing the amplitude of burst and chroma, measure the input
Others:Preset amplitude at which Pin20 output amplitude is +1dB/-1dB against
the one for 300mVp-p input, that is "VACCH"/"VACCL".
C2 TOF Characteristics RGB Mute:0 (1)Set “C-BPF” to 1, “Color System” to 010, “TEST Mode” to
(4.43MHz) Y Mute:1 00001000, and Sub address “0A” is X0011XXX.
TEST:01000111 (2)Input a sweep signal into Pin43.
/ F0T443
C-BPF:0/1 (3)Observe the frequency response at Pin13 and measure the
/ QT443 Color System: Peaking Frequency / Q of chroma filter, that is "F0T443" / "QT443".
BPF Characteristics 010/100 (4)Set C-BPF to 0 and Color System to 010 and repeat (2)&(3),
(4.43MHz) TEST Mode: that is "F0B443" / "QB443".
/ F0B443 00001000 (5)Set C-BPF to 1 and Color System to 100 and repeat (2)&(3),
/ QB443 Sub Add.”0A”: that is "F0T358" / "QT358".
X0011XXX (6)Set C-BPF to 0 and Color System to 100 and repeat (2)&(3),
TOF Characteristics Others:Preset that is "F0B358" / "QB358".
(3.58MHz)
/ F0T358
/ QT358
BPF Characteristics
(3.58MHz)
/ F0B358
/ QB358
C3 C Delay Time RGB Mute:0 (1)Input a 4.43MHz PAL rainbow color-bar(300mVp-p,
/ tCDEL Y Mute:1 burst:chroma=1:1) with sync into Pin38&43.
Uni-Color:127 (2)Observe the Pin20 output, measure the delay time between
Delay Time
Others:Preset Pin43 and Pin20, that is "tCDEL".
Difference between (3)Calculate;"•tY/C"=tYDEL-tCDEL
Y/C
/ •tY/C
C4 Color Characteristics RGB Mute:0 (1)Input a 4.43MHz PAL rainbow color-bar(300mVp-p,
/ GCOLMAX Color:0/64/127 burst:chroma=1:1) with sync into Pin38&43.
/ GCOLMIN Y Mute:1 (2)Measure the Pin20 amplitude for Color 127/64/0, that is VCOLMAX
Uni-Color:127 / VCOLCEN/ VCOLMIN.
Others:Preset (3)Calculate; "GCOLMAX"=20*log(VCOLMAX/VCOLCEN)
"GCOLMIN"=20*log(VCOLMIN/VCOLCEN)
C5 Uni-Color RGB Mute:0 (1)Input a 4.43MHz PAL rainbow color-bar(300mVp-p,
Characteristics for C Uni-Color:0/127 burst:chroma=1:1) with sync into Pin38&43.
/ GUCC Y Mute:1 (2)Measure the Pin20 amplitude for Uni-Color 127/0, that is
Others:Preset VUCCMAX, and VUCCMIN.
(3)Calculate;"GUCC"=20*log(VUCCMIN/VUCCMAX)
C6 Tint Characteristics RGB Mute:0 (1)Input a 3.58MHz NTSC rainbow color-bar (286mVp-p,
(3.58MHz) Tint:0/64/127 burst:chroma=1:1) with sync into Pin38&43.
Y Mute:1 (2)Set Tint to 64 and adjust the burst phase so that the 6th bar of
/ ••358MAX
Uni-Color:127 Pin20 output is maximum, that is •358CEN.
/ ••358MIN Others:Preset (3)Change Tint to 127/0 and adjust the burst phase so that the 6th
Tint Characteristics bar of Pin20 output is maximum, that is •358MAX /•358MIN.
(4.43MHz) (4)Calculate; "••358MAX"=-(•358MAX-•358CEN)
/ ••443MAX "••358MIN"=-(•358MIN-•358CEN)
/ ••443MIN (5)Input a 4.43MHz NTSC rainbow color-bar (286mVp-p,
burst:chroma=1:1) with sync into Pin43 and repeat (2)&(3), that is
•443CEN /•443MAX /•443MIN.
(7)Calculate; "••443MAX"=-(•443MAX-•443CEN)
"••443MIN"=-(•443MIN-•443CEN)

Ver3.7 00/01/28 40




Note Items/Symbols Bus conditoins Measurement methods

C7 Relative Amplitude RGB Mute:0 (1)Input a 4.43MHz PAL rainbow color-bar(300mVp-p,
(PAL) Y Mute:1 burst:chroma=1:1) with sync into Pin38&43.
/ VPR/B Uni-Color:127 (2)Measure the amplitude of Pin18/19/20 output, that is
/ VPG/B Others:Preset "VPROUT"/ "VPGOUT" / "VPBOUT"
Relative Amplitude (3)Calculate; " VPR/B "=VPROUT/VPBOUT
(NTSC1) " VPG/B "=VPGOUT/VPBOUT
/ VN1R/B (4)Input a 3.58MHz NTSC rainbow color-bar (286mVp-p,
/ VN1G/B burst:chroma=1:1) with sync into Pin38&43.
Relative Amplitude (5)Set NTSC Phase to NTSC1/NTSC2.
(NTSC2) (6)Repeat (2)&(3), that is “VN1R/B”/” VN1G/B”/” VN2R/B”/” VN2G/B”.
/ VN2R/B
/ VN2G/B
Relative Amplitude
(DVD)
/ VDR/B
/ VDG/B
C8 Relative Phase (PAL) RGB Mute:0 (1)Input a 4.43MHz PAL rainbow color-bar(300mVp-p,
/ •PR-B Y Mute:01 burst:chroma=1:1) with sync into Pin38&43.
Uni-Color:127 (2)Observe the Pin18/19/20 output, measure the R/G/B modulation
/ •PG-B
NTSC Phase: angle (•PR/•PG/•PB) accoeding following figure and equality.
Relative Phase 00/01/10 For •PR ; Peak:3rd bar, •0R=90
(NTSC1) Others:Preset For •PG ; Peak(nagative):4th bar, •0G=240
/ •N1R-B For •PB ; Peak:6th bar, •0B=0
/ •N1G-B Calculate; "•PR-B"=•PR-•PB
Relative Phase "•PG-B"=•PG-•PB
(NTSC2) (4)Set NTSC Phase 00(NTSC1).
/ •N2R-B (5)Input a 3.58MHz NTSC rainbow color-bar (286mVp-p,
/ •N2G-B burst:chroma=1:1) with sync into Pin38&43, then repeat (2), that is
•N1R /•N1G /•N1B.
Relative Phase (DVD)
(6)Calculate; "•N1R-B"=•N1R-•N1B
/ •DR-B
"•N1G-B"=•N1G-•N1B
/ •DG-B (7)Set NTSC Phase 01(NTSC2).
(8) Repeat (5), that is •N2R /•N2G /•N2B.
(9)Calculate; "•N2R-B"=•N2R-•N2B
"•N1G-B"=•N1G-•N1B
(10)Set NTSC Phase 10(DVD).

C9 APC Pull-in Range RGB Mute:0 (1)Input a 4.43MHz PAL rainbow color-bar(300mVp-p,
(4.43MHz) Color System: burst:chroma=1:1) with sync into Pin38&43.
100/010 (2)Set Color System to 100(443PAL).
/ •F4APCP+
Others:Preset (3)For higher frequency than 4.43MHz, measure the burst
/ •F4APCP- frequency at which Pin13 DC level changes from low to high / from
APC Hold Range high to low, that is F4APCP+ / F4APCH+.
(4.43MHz) (4)For lower frequency than 4.43MHz, repeat (2), that is F4APCP- /
/ •F4APCH+ F4APCH-.
/ •F4APCH- (5)Calculate; "•F4APCP+"=F4APCP+-4433619
"•F4APCP-"=4433619-F4APCP-
APC Pull-in Range
"•F4APCH+"=F4APCH+-4433619
(3.58MHz)
"•F4APCH-"=4433619-F4APCH-
/ •F3APCP+ (6)Input a 3.58MHz NTSC rainbow color-bar (286mVp-p,
/ •F3APCP- burst:chroma=1:1) with sync into Pin38&43.
APC Hold Range (7)Set Color System to 010(358NTSC).
(3.58MHz) (8)For higher frequency than 3.58MHz, repeat (2), that is F3APCP+ /
/ •F3APCH+ F3APCH+.
(9)For lower frequency than 3.58MHz, repeat (2), that is F3APCP- /
/ •F3APCH-
F3APCH-.
(10)Calculate; "•F3APCP+"=F3APCP+-3579545
"•F3APCP-"=3579545-F3APCP-
"•F3APCH+"=F3APCH+-3579545
"•F3APCH-"=3579545-F3APCH-

Ver3.7 00/01/28 41




Note Items/Symbols Bus conditoins Measurement methods

C10 APC Control RGB Mute:0 (1)Connect Pin43 to GND via a 1uF capacitor.
Sensitivity (4.43MHz) Color System: (2)Set Color System to 100(443PAL).
100/010 (3)Adjust Pin11 voltage so that the Pin13 output frequency is
/ •443
Others:Preset 4.433619MHz, that is V4APCCEN.
APC Control (4)Measure the Pin13 output frequency when Pin11 voltage is
Sensitivity (3.58MHz) V4APCCEN+100mV / V4APCCEN-100mV, that is F4APC+ / F4APC-.
/ •358 (5)Calculate; "•443"=(F4APC+-F4APC-)/200
(6)Set Color System to 010(358NTSC).
(7)Adjust Pin11 voltage so that the Pin13 output frequency is
3.579545MHz, that is V3APCCEN.
(8)Measure the Pin13 output frequency when Pin11 voltage is
V3APCCEN+100mV / V3APCCEN-100mV, that is F3APC+ / F3APC-.
(9)Calculate; "•358"=(F3APC+-F3APC-)/200

C11 PAL ID Sensitivity P/N ID Sens:0/1 (1)Set P/N ID Sens. to 0.

(Normal Mode) Color System: (2)Set Color System to 100(443PAL).
100/010 (3)Input a 4.43MHz PAL rainbow color-bar(300mVp-p,
/ VPALIDON
Y Mute:01 burst:chroma=1:1) with sync into Pin38&43.
/ VPALIDOFF Uni-Color:127 (4)Measure the burst amplitude at which Pin13 DC level changes
PAL ID Sensitivity RGB Mute:0 from low to high / from high to low, that is "VPALIDON" / "VPALIDOFF".
(Low Mode) Others:Preset (5)Set Color System to 010(358NTSC).
/ VPALIDLON (6)Input a 3.58MHz NTSC rainbow color-bar (286mVp-p,
/ VPALIDLOFF burst:chroma=1:1) with sync into Pin38&43, and repeat (3), that is
NTSC ID Sensitivity "VNTIDON" / "VNTIDOFF".
(Normal Mode) (7)Set P/N ID Sens.to 1, repeat (2) ~ (6), that is "VPALIDLON" ,
/ VNTIDON "VPALIDLOFF" , "VNTIDLON" and "VNTIDLOFF".
/ VNTIDOFF
NTSC ID Sensitivity
(Low Mode)
/ VNTIDLON

/ VNTIDLOFF
C12 fsc Continuous Wave RGB Mute:00 Measure the amplitude of Pin20 output, that is "VCW ".
Output Level Others:Preset
/ VCW
C13 Half Tone RGB Mute:0 (1)Input a 4.43MHz PAL rainbow color-bar(300mVp-p,
Characteristics for C Ysm Mode:0 burst:chroma=1:1) with sync into Pin38&43.
/ GHTC Y Mute:01 (2)Supply Pin15 2V and measure the amplitude of Pin20 output,
Uni-Color:127 that is VPBHTC.
Others:Preset (3)Calculate;"GHTC"=20*log(VPBHTC/VPBOUT)
C14 Sub-Color Control RGB Mute:00 1)Input a signal(f0=100kHz,300mV) of following figure into
Characteristics Y Mute:01 Pin38,44&45.
/ •SCOLMAX Uni-Color:127 (2)Measure the Pin20 amplitude for Sub-olor 32/16/0, that is
/ •SCOLMIN Sub-Color:0 VSCMAX / VSCLCEN/VSCMIN.
/16/32 (3)Calculate; "•SCOLMAX "=20*log(VSCMAX / VSCLCEN)
Others:Preset "•SCOLMIN "=20*log(VSCMIN / VSCLCEN)

Sinusoidal wave
Frequency f 0

Amplitude V 0

pin38 input

pin16 input

Ver3.7 00/01/28 42




SECAM STAGE
Note Items/Symbols Bus conditoins Measurement methods
SE1 Bell Monitor output RGB Mute:0 (1) Input a 75% color bar signal (200mVp-p at R ID) into Pin43.
voltage TEST Mode: (2) Set BUS data so that “
/ embo 00001000 (3) TEST Mode” is 00001000 and Sub address “0A” is X0111XXX.
Sub Add.”1A”: (3) Measure R-Y ID amplitude at Pin13, that is "ebmo".
X0111XXX
Others:Preset

SE2 Bell filter f0 RGB Mute:00 (1) Input a 20mVp-p sine wave whose frequency is sweep into
/ f0B-C TEST Mode: Pin43.
00001000 (2) Set BUS data so that “TEST Mode” is 00001000 and Sub
Sub Add.”0A”: address “0A” is X0111XXX.
X0111XXX (3) Measure the frequency at which Pin13 output is the biggest,
Bell f0:0 that is "f0BEL" .
Y Mute:1 (4) Calculate : "f0B-C"=f0BEL-4,286 [kHz].
Others:Preset

SE3 Bell filter f0 variable RGB Mute:00 (1) Input a 20mVp-p sine wave whose frequency is sweep into
range TEST Mode: Pin43.
/ f0B-VR 00001000 (2) Set BUS data so that “TEST Mode” is 00001000 and Sub
Sub Add.”0A”: address “0A” is X0111XXX.
X0111XXX (3) Set BUS data so that “Bell f0” is +35kHz.
Bell f0:1 (4) Measure the frequency at which Pin 13 output is the biggest,
Y Mute:1 that is f0BELH.
Others:Preset (5) Calculate : " f0B-VR "= f0BELH -4,286 [kHz]
SE4 Bell filter Q RGB Mute:00 (1)Input a 20mVp-p sine wave whose frequency is sweep into
/ QBEL TEST Mode: Pin43.
00001000 (2)Set BUS data so that “TEST Mode” is 00001000 and Sub
Sub Add.”0A”: address “0A” is X0111XXX.
X0111XXX (4) Observe the frequency response of Pin13 output.
Y Mute:1 (5) Calculate : "QBEL = (MAX-3dB Band Width)/f0BEL.
Others:Preset
SE5 Color difference RGB Mute:00 (1) Input a 75% color bar(200mVp-p at R ID) into Pin43.
output amplitude Uni-Color:63 (2) Measure the R-Y output amplitude at Pin20, that is "VRS".
/ VBS Y Mute:1 (3) Measure the B-Y output amplitude at Pin22, that is "VBS".
/ VRS Others:preset
SE6 Color Difference (1)Calculate : "R/B-S"=VRS/VBS
Relative Amplitude
/ R/B-S

SE8 Color Difference S/N RGB Mute:00 (1) Input a 200mVp-p non-modulated chroma signal into Pin43.
Ratio Uni-Color:63 (2) Measure the amplitude of noise on Pin20, that is nR.
/ SNB-S Y Mute:1 (3) Measure the amplitude of noise on Pin22, that is nB.
/ SBR-S Others:preset (4) Calculate : "SNB-S"=20log(2•2VBS/nB)
"SNR-S"=20log(2•2VRS/nR)

Ver3.7 00/01/28 43




Note Items/Symbols Bus conditoins Measurement methods

SE9 Linearity RGB Mute:00 (1) Input a 75% color bar(200mVp-p at R ID) into Pin43.
/ LinB Uni-Color:63 (2) Set BUS data so that “S black monitor” is “alignment”.
/ LinR Y Mute:1 (2) Measure the amplitude between Black and Cyan/Red, that is
Others:preset VCyan/VRed.
(3) Measure the amplitude between Black and Yellow/Blue, that is
VYellow/VBlue.
(4) Calculate : "LinR"=VCync/VRed
"LinB"=VYellow/VBlue
red
LinR

cyan
blue

LinB
yellow
SE10 Rising-Fall Time RGB Mute:00 (1) Input a 75% color bar(200mVp-p at R ID) into Pin43.
/ trfB Uni-Color:63 (2) Set BUS data so that “S black monitor” is “alignment”.
/ trfR Y Mute:1 (3) Measure the rising time(from 10% to 90%) between Green and
Others:preset Magenta at Pin 20/Pin 22, that is "trR"/"trB".
Magenta

trB•CtrR

Green 10% 90%

SE11 SECAM ID Sensitivity RGB Mute:00 (1)Input a 75% color bar(200mVp-p at R ID) into Pin43.
(Normal Mode) Y Mute:1 (2)Set BUS data so that “S ID Sens” is Normal, “S ID Mode” is H.
/ VSIDHON S ID Sens:0/1 (3)Measure the burst amplitude at which Pin13 DC level changes
/ VSIDHOFF S ID Mode:0/1 from low to high / from high to low, that is "VSIDHON" / "VSIDHOFF".
/ VSIDHVON Color (4)Set BUS data so that “S ID Mode” is H+V.
/ VSIDHVOFF System:101 (5)Repeat (3), that is "VSIDHVON" / "VSIDHVOFF".
SECAM ID Sensitivity Others:Preset (6)Set BUS data so that “S ID Sens” is Low, “S ID Mode” is H.
(Low Mode) (7)Repeat (3), that is "VSIDLHON" / "VSIDLHOFF".
/ VSIDLHON (8)Set BUS data so that “S ID Mode” is H+V.
/ VSIDLHOFF (9)Repeat (3), that is "VSIDLHVON" / "VSIDLHVOFF".
/ VSIDLHVON
/ VSIDLHVOFF
SE12 Gate Pulse Width RGB Mute:00 (1)Input a 75% color bar(200mVp-p at R ID) into Pin43.
Variable Range TEST Mode: (2)Set BUS data so that “TEST Mode” is 00001000 , Sub address
/ WGP+200 00001000 “0A” is X1001XXX , and“Color System” is Fixed SECAM.
/ WGP Sub Add.”0A”: (3)Measure the gate pulse widths when BUS data of “SECAM GP
/ WGP-200 X1001XXX Phase” is +200ns / normal / -200ns, those are “WGP+200”,
Color “WGP” and “WGP-200”.
System:101
Others:Preset
S13 SECAM black RGB Mute:00 (1)For B-Y/R-Y Black Adj.:8, measure the DC level of picture period
adjustment Color at Pin22/20, that is VSBCEN / VSRCEN.
characteristic System:101 (3)For B-Y Black Adj.:0/15, measure the DC level change of picture
/ VSBMAX S black Monitor:1 period against VSBCEN at Pin22, that is "VSBMIN" / "VSBMAX".
/ VSRMAX S B-Y black Adj.:
/ VSRMIN 0/15 (4)For R-Y Black Adj.:0/15, measure the DC level change of picture
/ VSRMIN S R-Y black Adj.: period against VSRCEN at Pin20, that is "VSRMIN" / "VSRMAX".
SECAM black 0/15 (5)Calculate;
adjustment sensitivity Others:Preset "•VSECB"=(VSBMAX-VSBMIN)/16
/•VSB "•VSECR"=(VSECRMAX-VSECRMIN)/16
/•VSR

Ver3.7 00/01/28 44




TEXT STAGE(RGB Mute:0 / RGB cut off:63 / DC rest.:10)

Note Items/Symbols Bus conditoins Measurement methods
T1 V-BLK Pulse Output All:Preset (1)Input a cmposite sync signal into Pin38.
Level (2)Measure the DC level of V/H blanking period at Pin20, that is
/ VVBLK "VVBLK" / "VHBLK".
H-BLK Pulse Output
Level

/ VHBLK
T2 RGB Output Black RGB Mute:0 (1)Input a 0IRE Y signal with sync into Pin38&39.
Level (0IRE DC) Color:0 (2)Measure the DC level of picture period at Pin20, that is "VBLACK".
/ VBLACK R cut off:63
DC rest.:10
Others:Preset
T3 RGB Output White RGB Mute:0 (1)Input a 100IRE Y signal with sync into Pin38&39.
Level(100 IRE AC) R cut off:63 (2)Measure the amplitude from 0 to 100IRE at Pin20, that is
/ VWHITE DC rest.:10 "VWHITE".
Uni-Color:127
Color:0
Others:Preset
T4 Cut-off Voltage RGB Mute:0 (1)Input a 0IRE Y signal with sync into Pin38&39.
Variable Range DC rest.:10 (2)Measure the DC level of picture period at Pin22 for B Cut-
/ •VCUT+ B Cut Off:0/255 off:255/0 , that is
/ •VCUT- Color:0 VCUTMAX / VCUTMIN.
Others:Preset (3)Calculate; "•VCUT+"=VCUTMAX-VBLACK "•VCUT-"=VCUTMIN-VBLACK
T5 Drive Control Variable RGB Mute:0 (1)Input a 100IRE Y signal with sync into Pin38&39.
Range DC rest:10 (2)Measure the amplitude from 0 to 100IRE at Pin20 for B
/ GDR+ B Drive:0/127 drive127/0, that is
/ GDR- Uni-Color:127 VDRMAX / VDRMIN.
Color:0 (1) Calculate; "GDR+"=20*log(VDRMAX/VWHITE)
Others:Preset "GDR-"=20*log(VDRMIN/VWHITE)
T6 ABCL Contorol RGB Mute:0 (1)Input a 100IRE Y signal with sync into Pin38&39.
Voltage Range R cut off:63 (2)Decreasing the Pin28 voltage, measure the voltage at which
/ VABCLH DC rest.:10 Pin20 output
/ VABCLL ABL Gain:11 begins/stops decreasing, that is "VABCLH" / "VABCLL".
ACL Gain Uni-Color:127 (3)Measure the minimum amplitude of Pin20 output, that is VACLMIN.
Color:0 (4)Calculate; "GACL"=20*log(VACLMIN/VWHITE)
/ GACL Others:Preset
T7 ABL Start Point RGB Mute:0 (1)Input a 0IRE Y signal with sync into Pin38&39.
/ VABLP0 R cut off:63 (2)For ABL Point 00/01/10/11, decreasing the Pin28 voltage,
/ VABLP1 DC rest.:10 measure the
/ VABLP2 ABL Start Point: voltage at which Pin20 output begins decreasing, that is
/ VABLP3 00/01/10/11 VABL1/VABL2/VABL3/VABL4.
ABL Gain:11 (3)Calculate; "VABLP0"=VABL1-VABCLH
Uni-Color:127 "VABLP1"=VABL2-VABCLH
Color:0 "VABLP2"=VABL3-VABCLH
Others:Preset "VABLP3"=VABL4-VABCLH
T8 ABL Gain RGB Mute:0 (1)Input a 0IRE Y signal with sync into Pin38&39.
/ VABLG0 R cut off:63 (2)For ABL Gain 00/01/10/11, measure the DC level of picture
/ VABLG1 DC rest.:10 period at
/ VABLG2 ABL Gain: Pin20 when Pin28 voltage is VABCLL, that is
/ VABLG3 00/01/10/11 VABL5/VABL6/VABL7/VABL8.
Uni-Color:127 (3)Calculate; "VABLG0"=VABL5-VBLACK
Color:0 "VABLG1"=VABL6-VBLACK
Others:Preset "VABLG2"=VABL7-VBLACK
"VABLG3"=VABL8-VBLACK

Ver3.7 00/01/28 45




Note Items/Symbols Bus conditoins Measurement methods

T9 Analog RGB Dynamic RGB Mute:0 (1)Input a composite sync signal into Pin38.
Range R cut off:63 (2)Supply 2V to Pin15.
/ DRTX DC rest.:10 (3)Input a signal of following figure into Pin16.
RGB Contrast:32 (4)Increasing the amplitude of Pin16 input, measure the amplitude
Ysm Mode:1 at which
Others:Preset the Pin20 amplitude stops increasing, that is "DRTX".
Sinusoidal wave
Frequency f 0

Amplitude V 0

pin38 input

pin16 input

T10 Analog RGB Contrast RGB Mute:0 (1)Input a cmposite sync signal into Pin38.
Control Characteristic R cut off:63 (2)Supply 2V to Pin15.
/ GTXCMAX DC rest.:10 (3)Input a signal of NOTE:T9 figure(f0=100kHz,V0=0.2Vp-p) into
/ GTXCCEN Ysm Mode:1 Pin16.
/ GTXCMIN RGB Contrast: (4)For RGB Contrast 63/32/0, measure the amplitude of Pin20
0/32/63 output, that is
Others:Preset VTXCMAX / VTXCCEN / VTXCMIN.
(5)Calculate; "GTXCMAX"=20*log(VTXCMAX/0.2)
"GTXCCEN"=20*log(VTXCCEN/0.2)
"GTXCMIN"=20*log(VTXCMIN/0.2)
T11 Analog RGB RGB Mute:0 (1)Supply 2V to Pin15.
Brightness Control R cut off:63 (2)Connect Pin16 to GND via a 0.1uF capacitor.
Characteristic DC rest.:10 (3)For Brightness 127/64/0, measure the DC level of picture period
/ VTXBRMAX Ysm Mode:1 at Pin20,
/ VTXBRCEN Brightness: that is "VTXBRMAX" / "VTXBRCEN" / "VTXBRMIN".
/ VTXBRMIN 0/64/127
Others:Preset
T12 Analog RGB Mode RGB Mute:0 (1)Input a cmposite sync signal into Pin38.
Switching Level Ysm Mode:1 (2)Input a signal of NOTE:T9 figure into Pin16.
/ VYS RGB Contrast:32 (3)Increasing the Pin15 voltage, measure the voltage at which the
Others:Preset signal
inputted into Pin16 appears at Pin20, that is "VYS".
T13 Analog RGB Mode RGB Mute:0 (1)Input a 50IRE Y singnal with sync into Pin38&39.
Transfer R cut off:63 (2)Connect Pin16 to GND via a 0.1uF capacitor.
Characteristic DC rest.:10 (3)According to following figure, measure the Analog RGB Mode
/ •RYS Ysm Mode:1 Transfer
/ tPRYS Others:Preset Characteristic.
/ •FYS 1H
/ tPFYS

20 ƒÊs
20 ƒÊs
Pin15 Input
20 ns 20 ns

50%

tPR YS
tPF YS
Pin20 Output
100%
90%
50%
10%
0%
ĄR YS ĄF YS

Ver3.7 00/01/28 46




Note Items/Symbols Bus conditoins Measurement methods

T14 Cross Talk from RGB Mute:0 (1) Input a composite sync signal into Pin38.
Analog RGB to TV R cut off:63 (2) Connect Pin39 to GND via a 1uF capacitor.
/ CTTX-TV DC rest.:10 (3) Input a sine wave signal (f=4MHz, Video amplitude=0.5Vp-p)
Ysm Mode:1 into Pin16.
Uni-color:127 (4) Supply 0V to Pin15.
RGB contrast:63 (5) Measure the amplitude at Pin20, that is VTV.
Others:Preset (6) Supply 2V to Pin15.
(7) Measure the amplitude of 4MHz signal at Pin20, that is V TX.
(8) (8)Calculate;"CTTX-TV"=20*log(VTV/ VTX)
T15 Cross Talk from TV to RGB Mute:0 (1) Input a sine wave signal (f=4MHz, Video amplitude=0.5Vp-p)
Analog RGB R cut off:63 with sync into Pin38&39.
/ CTTV-TX DC rest.:10 (2) Connect Pin16 to GND via a 0.1uF capacitor.
Ysm Mode:1 (3) Supply 2V to Pin15.
Uni-color:127 (4) Measure the amplitude at Pin20, that is VTX.
RGB contrast:63 (5) Supply 0V to Pin15.
Others:Preset (6) Measure the amplitude of 4MHz signal at Pin20, that is V TV.
(7) Calculate;"CTTV-TX"=20*log(VTX/ VTV)
T16 SECAM Black Level RGB Mute:0 (1) Set S black monitor to 1.
Adj. Characteristics R cut off:63 (2)For B-Y/R-Y Black Adj.:8, measure the DC level of picture period
/ VSECBMAX DC rest.:10 at Pin22/20, that is VSECBCEN / VSECRCEN.
/ VSECRMAX Color (3)For B-Y Black Adj.:0/15, measure the DC level change of picture
/ VSECBMIN System:111 B-Y period against VSECBCEN at Pin22, that is "VSECBMIN" / "VSECBMAX".
/ VSECRMIN Black Adj: (4)For R-Y Black Adj.:0/15, measure the DC level change of picture
SECAM Black Level 0/8/15 period against VSECRCEN at Pin20, that is "VSECRMIN" / "VSECRMAX".
Adj. Data Sensitivity R-Y Black Adj: (5)Calculate; "•VSECB"=(VSECBMAX-VSECBMIN)/16
/ •VSECB 0/8/15 "•VSECR"=(VSECRMAX-VSECRMIN)/16
S black monitor:1
/ •VSECR Others:Preset
T17 Base band TINT RGB Mute:0 (1)Input a signal(f0=100kHz, 100mVp-p) of NOTE T9 into
characteristic R cut off:63 Pin44&38.
/ ••BBMAX DC rest.:10 (2)Into Pin45, into a signal with the same amplitude but 90deg
/ ••BBMIN Uni-color:127 phase advanced compared to the signal input to pin44.
Others:Preset (3)When baseband TINT is changed ‘10000’ to“00000”, measure
the amount of change in the output phase of Pin20, that is
“••BBMIN”.
(4) When baseband TINT is changed ‘10000’ to“11111”, measure
the amount of change in the output phase of Pin20, that is
“••BBMIN”.

T18 Analog RGB•RGB RGB Mute:0 (1)Input a 0IRE signal with sync into Pin38&39.
Output Voltage Axes R/G/B cut off:63 (2)Connect Pin16,17,18 to GND via 0.01•F.
Brightness:63
Difference (3)Measure the DC level of picture period at Pin20,21,22, that is
DC rest.:10
••VR-G Color:0 RY/GY/BY.
••VG-B Uni-color:127 (4)Supply Pin15 to 2V.
••VB-R Others:Preset (5) Measure the DC level of picture period at Pin20,21,22, that is
RT/GT/BT.
(6)Calculate;
•R • RT • RY
•G • GT • GY
•B • BT • BY
“•VR-G” • •R • •G
“•VG-B” • •G • •B
“•VB-R” • •B • •R

DEF STAGE
Note Items/Symbols Bus conditoins Measurement methods
D1 AFC Inactive Period All:Preset (1)Input a 50Hz/60Hz composite sync signal into Pin38.
/ T50AFCOFF (2)Measure "T50AFCOFF" / "T60AFCOFF" at Pin29. (cf. Fig.D1)
/ T60AFCOFF

Ver3.7 00/01/28 47




Note Items/Symbols Bus conditoins Measurement methods

D2 H-OUT Start Voltage All:Preset (1)Let Pin1/14/37/42 be open.
/ VHON (2)Increasing Pin31 voltage, measure the voltage at which H
OUT pulse appears at Pin32, that is "VHON".

D3 H-OUT Pulse Duty All:Preset (1) Measure tHOUT1 & tHOUT2 at Pin32.
/ W HOUT (2)Calculate;"W HOUT"=tHOUT1/(tHOUT1+tHOUT2)*100

tHOUT1 tHOUT2

D4 H-OUT Freq. on AFC AFC Gain:11 (1)Input a 50Hz composite sync signal into Pin38.
Stop Mode (OFF) (2)Measure the H OUT frequency at Pin32, that is "FHAFCOFF".
/ FHAFCOFF Others:Preset
D5 Horizontal Free-run V-Freq:001/010 For V-Freq 001/010, measure the H OUT frequency at Pin32, that
Frequency Others:Preset is "FH50FR" / "FH60FR".
/ FH50FR
/ FH60FR
D6 Horizontal Freq. All:Preset (1)Connect Pin29 to Vcc via a 10k• and measure the H OUT
Variable Range frequency at Pin32, that is "FHMAX".
/ FHMAX (2)Connect Pin29 to GND via a 68k• and measure the H OUT
/ FHMIN frequency at Pin32, that is "FHMIN".
D7 Horizontal Freq. All:Preset (1) Measure the Pin29 voltage at which H OUT frequency is
Control Sensitivity 15.734kHz, that is VH15734.
/ •HAFC (2)Measure the H OUT frequency when Pin29 voltage is VH15734 +
50mV /VH15734 - 50mV, that is FHHIGH / FHLOW .
(3)Calculate;"•HAFC"=(FHHIGH-FHLOW )/100
D8 Horizontal Pull-in All:Preset (1)Input a composite sync signal into Pin38.
Range (2)Decreasing the horizontal frequency from 17kHz, measure the
/ •FHPH frequency at which H OUT synchronized with SCP Out(Pin29),
/ •FHPL that is FHPH.
(3)Increasing the horizontal frequency from 14kHz, measure the
frequency at which H OUT synchronized with SCP Out(Pin29),
that is FHPL.
(4)Calculate; "•FHPH"=FHPH-15734
"•FHPL"=15625-FHPL
D9 H-OUT Voltage All:Preset (1)Measure the high level of H OUT at Pin32, that is "VHOUTH".
/ VHOUTH (2)Measure the low level of H OUT at Pin32, that is "VHOUTL".
/ VHOUTL
D10 Horizontal Freq. All:Preset (1)Measure the H OUT frequency when H Vcc(Pin31) is
Dependence on Vcc 8.5V/9.5V, that is FHVCCH/FHVCCL.
/ •FHVCC (2)Calculate;"•FHVCC"=(FHVCCH-FHVCCL)/1
D11 FBP Phase All:Preset (1) Input a composite sync signal into Pin38.
/ PHFBP (2)According to the following figure, measure "PHFBP" &
H-Sync. Phase "PHHSYNC".

/ PHHSYNC

Sync in(Pin38)

H AFC(Pin29)

FBP in(Pin30)

Ver3.7 00/01/28 48




Note Items/Symbols Bus conditoins Measurement methods

D12 Horizontal Position H Position:0/31 (1)Input a composite sync signal into Pin38.
Variable Range Others:Preset (2)Changing BUS data of “Horizontal Position” from 0 to 31,
/ •PHHPOS measure "•PHHPOS" according to the following figure.

(00)

FBP in(Pin30) ĢPHHPOS

(1F)

D13 AFC-2 Pulse All:Preset (1)Input a composite sync signal into Pin38.
Threshold Level (2)Decreasing the FBP high level, measure the DC level at which
/ VAFC2 H OUT phase changes against Sync Out phase, that is "VAFC2".
D14 H-BLK Pulse All:Preset (1) Input a composite sync signal into Pin38.
Threshold Level (2)Increasing the FBP high level, measure the DC level at which
/ VHBLK H blanking begins to work, that is "VHBLK".

D15 Black Peak Det. Stop TEST:00001000 (1) Input a composite sync signal into Pin38.
Period (H) Black Stretch:01 (2) According to the following figure, measure "PHBPDET" &
/ PHBPDET Others:Preset "W BPDET".
/ W BPDET 63.5ƒÊs
Sync in(Pin38)
4.7ƒÊs 0.25V

H AFC(Pin29)

ĢPHHPOS
4.3V
WBPDET
SCP OUT(Pin30) 0V

D16 Gate Pulse Start All:Preset (1) Input a composite sync signal into Pin38.
Phase (2)According to the following figure, measure "PHGP" & "W GP".
/ PHGP 63.5ƒÊs
Gate Pulse Width Sync in(Pin38)
4.7ƒÊs 0.25V
/ W GP

H AFC(Pin29)

PHGP WGP
4.3V

SCP OUT(Pin30) 0V

D17 Vertical Oscillation All:Preset (1) Let Pin1/14/37/42 be open.

Start Voltage (2)Increasing Pin31 voltage, measure the voltage at which V
/ VVON Ramp signal
(3)appears at Pin24, that is "VVON".
D18 Vertical Free-run V-Freq: (1)Input a 50Hz composite sync signal into Pin38.
Frequency 000/001/010 (2)Set V-Freq to 000.
/ FVAUFR50 Others:Preset (3)For no input, measure the frequecy of V Ramp at Pin22, that is
/ FVAUFR60 "FVAUFR50".
/ FV50FR (3) Input a 60Hz composite sync signal into Pin38.
/ FV60FR (4) Repeat (2)&(3), that is “FVAUFR60”
(5) Set V-Freq. To 001/101, repeat (2), that is "FV50FR" / "FV60FR".
D19 Gate Pulse V- All:Preset (1) Input a 50Hz/60Hz composite sync signal into Pin38.
Masking Period (2)Measure "T50GPM" / "T60GPM" at Pin30. (cf. Fig.D21)
/ T50GPM
/ T60GPM

Ver3.7 00/01/28 49




Note Items/Symbols Bus conditoins Measurement methods

D20 V. Ramp DC on V STOP:1 (1)Set V STOP to 1.
Service Mode Others:Preset (2)Measure the DC level of Pin24, that is "VNOVRAMP".
/ VNOVRAMP
D21 Vertical Pull-in Range V-Freq: (6) Input a composite sync signal into Pin38.
(Auto) 000/001/010 (7) For V-Freq 000/001/010, increasing the input vertical period
/ FVPAUL Others:Preset from 220H by 0.5H step, measure the period at which input
/ FVPAUH signal synchronized with V Ramp(Pin24), that is "FVPAUL" /”
Vertical Pull-in Range FVP50L”/ "FVP60L".
(50Hz) (8) (3)For V-Freq 000/001/010, decreasing the input vertical
/ FVP50L period from 360H by 0.5H step, measure the period at which
/ FVP50H input signal synchronized with V Ramp, that is "FVPAUH" /”
Vertical Pull-in Range FVP50H”/ "FVP60H".
(60Hz)
/ FVP60L
/ FVP60H
D22 Vertical Period on V-Freq: For V-Freq 100/101/110/111, measure the vertical period at SCP
Fixed Mode 100/101/110/ out (Pin30), that is "TV312.5"/"TV262.5" / "TV313"/"TV263" .
/ TV3125 111
/ TV2625 Others:Preset
/ TV313
/ TV263
D23 V-BLK Start Phase All:Preset (1)Input a 50Hz/60Hz composite sync signal into Pin38.
/ PH50VBLK (2)Measure "T50AFCOFF" / "1T60AFCOFF" at Pin30. (cf. Fig.D25)
/ PH60VBLK
V-BLK Width
/ W 50VBLK

/ W 60VBLK
D24 Sand Castle Pulse All:Preset Measure "VSCPH" / "VSCPM" / "VSCPL" at Pin30.
Level
/ VSCPH VSCPH
/ VSCPM
/ VSCPL VSCPM

VSCPL

D25 Vertical Ramp All:Preset Measure the V Ramp amplitude at Pin24, that is "VVRAMP".
Amplitude
/ VVRAMP
D26 Vertical AMP Gain All:Preset (1)Let Pin26 be open.
/ GVAMP (2)Changing the Pin25 DC voltage, measure "VVOMAX" / "VVOMIN" /
Vertical AMP "GVAMP"
Max.Output Level according to a following figure.
/ VVOMAX #26DC
Vertical AMP
Min.Output Level

/ VVOMIN
VVOMAX
ĢV=GVAMP
=20log(ĢV#26/ĢV#25)
VVOMIN #25DC
D27 Vertical AMP All:Preset (1)Supply 7V to Pin25.
Max.Output Current (2)Measure the current from Pin26 to GND, that is "IVOMAX".
/ IVOMAX

Ver3.7 00/01/28 50




Note Items/Symbols Bus conditoins Measurement methods

D28 Vertical NFB V Size:0/32/63 (1)Measure the amplitude of NFB V Ramp at Pin25, that is
Amplitude Others:Preset "VNFB". (2)Measure the amplitude of NFB V Ramp at Pin25 for V-
/ VNFB Size 0/63, that is
Vertical Amplitude VNFBMIN / VNFBMAX.
Variable Range (3)Calculate; "•VVRAMPH"=(VNFBMAX-VNFB)/VNFB*100
/ •VVRAMPH "•VVRAMPL"=(VNFBMIN-VNFB)/VNFB*100
/ •VVRAMPL
D29 Vertical Linearity V Linearity:0/8/15 (1)For V Linearity 8, measure V1(from center to max.) and
Variable Range Others:Preset V2(from center to min.) at Pin24 according to a follownig figure.
/ •VLIN1+ (2)For V Linearity 15/0, measure VLIN1+ / VLIN1- and VLIN2+ / VLIN2-.
/ •VLIN1- (3)Calculate; "•VLIN1+"=(VLIN1+-V1)/V1*100
/ •VLIN2+ "•VLIN1-"=(VLIN1--V1)/V1*100
/ •VLIN2- "•VLIN2+"=(VLIN2+-V2)/V2*100
"•VLIN2-"=(VLIN2--V2)/V2*100

Pin24
V1 signal

V2

D30 Vertical S Correction V S Corr.:0/8/15 (1)For V S Correction:8, measure V1 and V2 at Pin24 according to
Variable Range Others:Preset a figure of NOTE:D32 .
/ •VS1+ (2)For V S Correction:15/0, measure VS1+ / VS1- and VS2+ / VS2-.
/ •VS1- (3)Calculate; "•VS1+"=(VS1+-V1)/V1*100
/ •VS2+ "•VS1-"=(VS1--V1)/V1*100
/ •VS2- "•VS2+"=(VS2+-V2)/V2*100
"•VS2-"=(VS2--V2)/V2*100
D35 Vertical Guard All:Preset Decreasing the Pin25 voltage from 5V, measure the voltage at
Voltage which Pin20 output drops to blanking level, that is "VVG".
/ VVG

Ver3.7 00/01/28 51




N.C.
FBP

10 9

8 7
N.C.
11

6
TC4538BP
R50:51kĦ

H IN
12

5
+
CE24:10ƒÊF

13

4
R51:
51kĦ

14

3
C29:1000pF
VR2:
50kB

15

C30:1000pF
VR1:
50kB

16

+9V
+ CE25:100ƒÊF
C16:0.01ƒÊF
+ CE13:100ƒÊF
C31:0.01ƒÊF
+9V

CE26:47ƒÊF
17
14
21

+
9

SW3:
P2
Reg.

CE14:0.22ƒÊF
C32:0.01ƒÊF R35:8.2kƒ¶ C15:0.1ƒÊF

29

28
H.AFC Filter
+5V

C17: + ABCL IN
R33:10kĦ D1:
8

+ 8200pF C106:2200pF
CE27:100ƒÊF R34:15kƒ¶ FBP IN/
30

27
ref R
9

SCP OUT
TC74HC125P

R29:5.6kĦ,1%
SCL

C18:0.01ƒÊF
R30:1kƒ¶ C14:0.47ƒÊF
10

31

26
5

R53: + H Vcc(9V) V OUT R32:1kĦ

SDA

4.7kƒ¶ CE15:100ƒÊF Q10:

11

R31:510Ħ
32

25
R36:
H OUT V NFB C13:8200pF
12

R37: 390ƒ¶ CE31:0.47ƒÊF

R52:
33

24
4.7kĦ
91Ħ Dig. GND V RAMP
+ ZD1: SW2:
13

4.7v R22:100Ħ
2

Q4:
R38:100Ħ R21:100Ħ
34

23
SCL IK IN R23:10kĦ
14

R20:3kĦ
R39:100Ħ Q5:
35

22
SDA B OUT
R206:270

R19:100Ħ R24:100Ħ
R18:3kĦ
+ R40:0pen
Q6:
36

21
CE28:47ƒÊF C019: + BLACK Det G OUT
R17:100Ħ
0.01ƒÊF CE16:1ƒÊF R16:3kƒ¶
Q7:
37

+ Dig. VDD R OUT 20

R15:100Ħ
CE17:100ƒÊF Q8:

1.2kĦ
R25:
38

19

+ Sync IN Y/C GND

CE18:1ƒÊF Q9:
C12:0.1ƒÊF
R26:510Ħ
39

18

+ Y IN EXT.B IN
+9V

CE29: CE19:0.22ƒÊF R27:510ƒ¶

R28:1.2kĦ
Q201

+ R203: R14:75Ħ
47ƒÊF C11:0.1ƒÊF +
40

17
P3

2kĦ DC Restor EXT.G IN

Reg.

CE11:100ƒÊF
R202: R201: C20:0.1ƒÊF R13:75ƒ¶
1kƒ¶ 1kƒ¶ C10:0.1ƒÊF
41

16

MON OUT EXT.R IN

+5V

C33:
TB1254N

0.01ƒÊF + C021:0.01ƒÊF
CE30:100ƒÊF R12:75ƒ¶
42

15

+ Y/C Vcc(5V) Ys/Ym SW

CE20:100ƒÊF CE10:100ƒÊF R300:10kƒ¶
CE21:1ƒÊF + +
43

14

C IN RGB Vcc(9V)
75Ħ
C9:0.01ƒÊF
C22:0.1ƒÊF R11:
44

13

U IN CW OUT Q3:
75Ħ X1:
C23:0.1ƒÊF 4.433619MHz C8:9pF
45

12

V IN X'tal
R204:75Ħ
C7:2200pF
46

11

+ EXT IN APC Filter +

CE201:1ƒÊF R10:33kƒ¶ CE9:0.22ƒÊF
R41:470ƒ¶ CE22:0.22ƒÊF CE8:2.2ƒÊF
47

10

+ LOOP Filter IF AGC +

C302:
CE202:1ƒÊF C24:1000pF 0.01ƒÊF R8:33kƒ¶
48

TV IN RF AGC
9

+
TB1254N TEST CIRCUIT

+
49

DE-EMP. NC CE7:4.7ƒÊF
8

C25:0.01ƒÊF
C6:0.01ƒÊF
50

PIF tank IF IN
7

430Ħ
T2:

SAW

R46:
R7:
Q14:

1kĦ
51

PIF tank IF IN C4
6

R45:
T1:

C5:
330ƒ¶ CE23:10ƒÊF 0.01ƒÊF
Q1:
L4:15ƒÊH

52

+ DC NF IF GND
5

R6:
R205:680Ħ
C2:0.01ƒÊF

Q2:
F1:Trap +
53

EXT AUDIO R5: R4:

CE4:100ƒÊF

AUDIO OUT
4

CE203:4.7ƒÊF
330Ħ
R44:

CE5:

R3: R2:
+
Q15:

+
+
54

IF DET OUT SIF OUT

3

CE6:
R43:2kĦ
R42:3kĦ CE3: R1:
22ƒÊF C3:
55

AFT OUT RIPPLE FIL L2:

2

+
R47:51Ħ
SW6:

C26:0.1ƒÊF P1:
SIF IN•^ +5V +9V
56

IF Vcc Reg.
1

C27:0.01ƒÊF
H CORRECTION IN
+

C28:0.01ƒÊF
CE2:100ƒÊF

CE1:47ƒÊF
C1:0.01ƒÊF

L1:12ƒÊH
R48:1kĦ
F2:
BPF R49:1kĦ

Ver3.7 00/01/28 52




Ver3.7 00/01/28 53




+9V

+9V
0.01ƒÊF 0.01ƒÊF

+ +
100ƒÊF 100ƒÊF

+9V
CE26:47ƒÊF CE14:0.22ƒÊF
+ C15:0.1ƒÊF
R35:8.2kĦ
P2

29

28
H.AFC Filter ABCL IN
Reg.

C17: +
R33:10kĦ D1:
C32:0.01ƒÊF 8200pF C106:2200pF
R34:15kĦ FBP IN/

30

27
+5V

SCP OUT ref R R29:5.6kĦ,1%

+ C18:0.01ƒÊF
CE27:100ƒÊF R30:1kƒ¶ C14:0.47ƒÊF

31

26
+ H Vcc(9V) V OUT R32:1kĦ
CE15:100ƒÊF Q10:
R31:510Ħ

32

25
R36:
H OUT V NFB
C13:8200pF
R37: 390ƒ¶ CE31:0.47ƒÊF

33

24
91Ħ Dig. GND + ZD1:
V RAMP
4.7v
R38:100Ħ R21:100Ħ
34

23
SCL IK IN
R20:3kĦ
R39:100Ħ
35

22
SDA B OUT
R206:270

R19:100Ħ
R18:3kĦ
R40:0pen
36

21
+ BLACK Det G OUT
R17:100Ħ
C019:0.01ƒÊF CE16:1ƒÊF R16:3kƒ¶
37

20
+ Dig. VDD R OUT
R15:100Ħ
CE17:100ƒÊF
+
38

19
Sync IN Y/C GND
CE18:1ƒÊF
C12:0.1ƒÊF
39

18
+ Y IN EXT.B IN
CE19:0.22ƒÊF
Q201

R203: R14:75Ħ
C11:0.1ƒÊF
40

17
2kĦ DC Restor EXT.G IN
R202: R201: C20:0.1ƒÊF R13:75ƒ¶
1kƒ¶ 1kƒ¶ C10:0.1ƒÊF
41

MON OUT EXT.R IN 16

TB1254N

C021:0.01ƒÊF
R12:75Ħ
42

15

+ Y/C Vcc(5V) Ys/Ym SW

CE20:100ƒÊF CE10:100ƒÊF R300:10kƒ¶
CE21:1ƒÊF + +
43

14

C IN RGB Vcc(9V)
75Ħ
C9:0.01ƒÊF
C22:0.1ƒÊF R11:
44

13

U IN CW OUT Q3:
75Ħ X1:
C23:0.1ƒÊF 4.433619MHz C8:9pF
45

12

V IN X'tal
R204:75Ħ
C7:2200pF
46

11

+ EXT IN APC Filter +

CE201:1ƒÊF R10:33kƒ¶ CE9:0.22ƒÊF
R41:470ƒ¶ CE22:0.22ƒÊF CE8:2.2ƒÊF
47

10
TB1254N APPLICATION CIRCUIT

+ LOOP Filter IF AGC +

C302:
CE202:1ƒÊF C24:1000pF 0.01ƒÊF R8:33kƒ¶
48

TV IN RF AGC
9

+
+
49

DE-EMP. NC CE7:4.7ƒÊF
8

C25:0.01ƒÊF
C6:0.01ƒÊF
50

PIF tank IF IN
7

430Ħ
T2:

SAW

R46:
R7:
Q14:

1kĦ C4
51

PIF tank IF IN
6

R45:
T1:

C5:
330ƒ¶ CE23:10ƒÊF 0.01ƒÊF
Q1:
L4:15ƒÊH

52

+ DC NF IF GND
5

R6:
R205:680Ħ
C2:0.01ƒÊF

Q2:
F1:Trap + R5:
53

EXT AUDIO R4:

CE4:100ƒÊF

AUDIO OUT
4

CE203:4.7ƒÊF
330Ħ
R44:

CE5:

R3: R2:
Q15:

+
+
54

IF DET OUT SIF OUT

3

CE6:
R43:2kĦ
R42:3kĦ CE3: R1:
22ƒÊF C3:
55

AFT OUT RIPPLE FIL L2:

2

C26:0.1ƒÊF P1:
SIF IN•^ +5V +9V
56

IF Vcc Reg.
1

H CORRECTION IN
+
CE2:100ƒÊF

C28:0.01ƒÊF
C1:0.01ƒÊF

L1:12ƒÊH
R48:1kĦ
F2:
BPF R49:1kĦ

0.01ƒÊF

+
100ƒÊF
+9V

Ver3.7 00/01/28 54




OUTLINE DRAWING Unit : mm

SDIP56-P-600-1.78

Ver3.7 00/01/28 55




•••• ••• •••

p.1 IF stage for L system,AM sound demodulation ••

Chroma stage U/V input ports Cb/Cr input ports

P.2 Block Diagram Pin9 RFAGC/SIF in RF AGC

Ripple filter BIAS

L-SECAM AM ••

H.AFC •••••• ••••••

9V 9V
P.3 Pin3 SIF OUT Interface 14 14
100Ħ
100Ħ

500Ħ
15kĦ 500Ħ
15kĦ
3
3
16kĦ
8.3kĦ
16.3kĦ
8.3kĦ
5
5
9V 9V
Pin4 Audio out Interface 14 14
100Ħ

ATT ATT
4 50kĦ 4 50kĦ

4.5V 5.3V
30kĦ 30kĦ
5 5

P.3 Pin6,7 IF IN 90dB• 90dB(•V)(Pin6-7)

field intensity level

P.4 Pin8 RF AGC/SIF IN RF AGC/SIF IN RF AGC

This terminal also lead to 1’st SIF ••

input pole.

Ver3.7 00/01/28 56




5V 9V
14 14

300Ħ 300Ħ
8 9
30kĦ to SELF ADJ
30kĦ to SELF ADJ

30kĦ 30kĦ
5 5
1

500Ħ

10kĦ

P.4 Pin10 IF AGC 2.2mF 2.2•F

42 42
P.8 Pin36 Black DET

4kĦ 4kĦ

36 36

2.5V 2.5V
19 19

P.9 Pin40 DC restor 42 42

50k 50k
40 40
10k 10k

19 19

Pin38 Sync in 1401IRE 140IRE

p.10 Pin44,45 U/V in U/V in Cb/Cr in

P.11 Pin50,51 PIF tank 27pF 18pF

p.14 RF AGC RF AGC delay point RF AGC delay point (Pin6-7)
01: 65dBm 01: 65 dB(•V)

3F: 100dBm 3F: 100 dB(•V)

P.15 DDS MODE SW•••

p.16 Split / Inter••• ••

p.17 U/V SW U/V Cb/Cr

p.18 Self Test 01:B OUT 10:R OUT ••

p.19 Self Adj. Self Adj. Self Test

Ver3.7 00/01/28 57




00: AFT (Normal) 10: RF AGC X

1/2

Noise Det•
(*3)Pin 1, 4, 5, 11, 12, 19, 26, 33, 34, (*3)Pin 1, 4, 5, 6, 9, 11, 12, 13, 19, 26,
p.22 (*3)
35, 42, 50, 51 are weak against •… 31, 32, 33, 34, 35, 37, 42, 43, 50, 51
are weak against •…

p.29 T4,T5 Cut off/Drive•spec.•• •••

Drive•spec.•• Drive•spec.••
T5 spec.••
min. typ. max. min. typ. max.
3 3.5 4 2.5 3.5 4.5
-6.0 -5.5 -5.0 -8.0 -5.5 -4.5

T18 ••

p.35 S2 Input a signal that 4.5[MHz], Input a signal that 4.5[MHz],

100[dBV], 2.5[kHz]…• 100[dBV], 25[kHz]…•

S3 Input a signal that 4.5[MHz], Input a signal that 4.5[MHz],

100[dBV], 2.5[kHz]…• 100[dBV], 25[kHz]…•

p.36 S8 Input a signal that 4.5[MHz], Input a signal that 4.5[MHz],

100[dBV], 2.5[kHz]…• 100[dBV], 25[kHz]…•

p.48 T18 ••

p.54 pin9 RF AGC/SIF IN RF AGC

Pin2 Ripple filter 10•F 22•F

p.55 Pin9 RF AGC/SIF IN RF AGC

Ver3.7 00/01/28 58
This datasheet has been downloaded from:

www.DatasheetCatalog.com

Datasheets for electronic components.