EN

SUBWING
SUBWING
700
700
USER’S AND INSTALLER’S MANUAL

V2.2
REV. 09/2022
 00. CONTENT 01. SAFETY INSTRUCTIONS
INDEX ATTENTION:
01. SAFETY INSTRUCTIONS 1B This product is certified in accordance with European
02. AUTOMATION Community (EC) safety standards.
CONNECTION SCHEME 4A
This product complies with Directive 2011/65/EU of the
INSTALLATION MAP 4A
TECHNICAL SPECIFICATIONS
European Parliament and of the Council, of 8 June 2011, on
4B
DIMENSIONS
the restriction of the use of certain hazardous substances
4B
in electrical and electronic equipment and with Delegated
03. INSTALLATION Directive (EU) 2015/863 from Commission.
GATE LEAF OPENING ANGLE 5A
BOX INSTALLATION (Applicable in countries with recycling systems).
5B
ASSEMBLING THE MOTOR AND LEVERS
This marking on the product or literature indicates that the
6A
MOUNTING THE MOTOR LEVER TO THE GATE
product and electronic accessories (eg. Charger, USB cable,
6B
EMERGENCY RELEASE electronic material, controls, etc.) should not be disposed
7A
LIMIT SWITCHES ASSEMBLY (OPTIONAL) of as other household waste at the end of its useful life. To
7A
avoid possible harm to the environment or human health
04. TROUBLESHOOTING resulting from the uncontrolled disposal of waste, separate
FINAL CONSUMERS AND SPECIALIZED INSTALLERS INSTRUCTIONS 7B these items from other types of waste and recycle them
responsibly to promote the sustainable reuse of material
resources. Home users should contact the dealer where
they purchased this product or the National Environment
Agency for details on where and how they can take these
items for environmentally safe recycling. Business users
should contact their vendor and check the terms and
conditions of the purchase agreement. This product and
its electronic accessories should not be mixed with other
commercial waste.
This marking indicates that the product and electronic
accessories (eg. charger, USB cable, electronic material,
controls, etc.) are susceptible to electric shock by direct or
indirect contact with electricity. Be cautious when handling
the product and observe all safety procedures in this manual.

1A 1B
EN EN
01. SAFETY INSTRUCTIONS

GENERAL WARNINGS the motorized door or gate from being triggered involuntarily.
• This manual contains very important safety and usage information.
very important. Read all instructions carefully before beginning the WARNINGS FOR TECHNICIANS
installation/usage procedures and keep this manual in a safe place • Before beginning the installation procedures, make sure that you have
that it can be consulted whenever necessary. all the devices and materials necessary to complete the installation
• This product is intended for use only as described in this manual. Any of the product.
other enforcement or operation that is not mentioned is expressly • You should note your Protection Index (IP) and operating temperature
prohibited, as it may damage the product and put people at risk to ensure that is suitable for the installation site.
causing serious injuries. • Provide the manual of the product to the user and let them know how
• This manual is intended firstly for specialized technicians, and does to handle it in an emergency.
not invalidate the user’s responsibility to read the “User Norms” • If the automatism is installed on a gate with a pedestrian door, a door
section in order to ensure the correct functioning of the product. locking mechanism must be installed while the gate is in motion.
• The installation and repair of this product may be done by qualified • Do not install the product “upside down” or supported by elements do
and specialized technicians, to assure every procedure are carried not support its weight. If necessary, add brackets at strategic points
out in accordance with applicable rules and norms. Nonprofessional to ensure the safety of the automatism.
and inexperienced users are expressly prohibited of taking any action, • Do not install the product in explosive site.
unless explicitly requested by specialized technicians to do so. • Safety devices must protect the possible crushing, cutting, transport
• Installations must be frequently inspected for unbalance and the and danger areas of the motorized door or gate.
wear signals of the cables, springs, hinges, wheels, supports and • Verify that the elements to be automated (gates, door, windows,
other mechanical assembly parts. blinds, etc.) are in perfect function, aligned and level. Also verify if
• Do not use the product if it is necessary repair or adjustment is the necessary mechanical stops are in the appropriate places.
required. • The central must be installed on a safe place of any fluid (rain, moisture,
• When performing maintenance, cleaning and replacement of parts, etc.), dust and pests.
the product must be disconnected from power supply. Also including • You must route the various electrical cables through protective tubes,
any operation that requires opening the product cover. to protect them against mechanical exertions, essentially on the
• The use, cleaning and maintenance of this product may be carried power supply cable. Please note that all the cables must enter the
out by any persons aged eight years old and over and persons whose central from the bottom.
physical, sensorial or mental capacities are lower, or by persons • If the automatism is to be installed at a height of more than 2,5m from
without any knowledge of the product, provided that these are the ground or other level of access, the minimum safety and health
supervision and instructions given by persons with experienced in requirements for the use of work equipment workers at the work of
terms of usage of the product in a safe manner and who understands Directive 2009/104/CE of European Parliament and of the Council of 16
the risks and dangers involved. September 2009.
• Children shouldn’t play with the product or opening devices to avoid • Attach the permanent label for the manual release as close as possible
2A
EN
01. SAFETY INSTRUCTIONS

• to the release mechanism. use or maintenance!

• Disconnect means, such as a switch or circuit breaker on the electrical • Safety norms are not followed in the installation, use and
panel, must be provided on the product’s fixed power supply leads in maintenance of the product.
accordance with the installation rules. • Instructions in this manual are not followed.
• If the product to be installed requires power supply of 230Vac or • Damaged is caused by unauthorized modifications
110Vac, ensure that connection is to an electrical panel with ground • In these cases, the warranty is voided.
connection.
• The product is only powered by low voltage satefy with central (only
at 24V motors)
MOTORLINE ELECTROCELOS SA.
WARNINGS FOR USERS Travessa do Sobreiro, nº29
4755-474 Rio Côvo (Santa Eugénia)
• Keep this manual in a safe place to be consulted whenever necessary. Barcelos, Portugal
• If the product has contact with fluids without being prepared, it must
immediately disconnect from the power supply to avoid short circuits,
and consult a specialized technician. SYMBOLS LEGEND:
• Ensure that technician has provided you the product manual and
• Important safety • Potentiometer
informed you how to handle the product in an emergency.
notices information
• If the system requires any repair or modification, unlock the
automatism, turn off the power and do not use it until all safety • Useful information • Connectors
conditions have been met. information
• In the event of tripping of circuits breakers of fuse failure, locate • Programming • Buttons
the malfunction and solve it before resetting the circuit breaker or information information
replacing the fuse. If the malfunction is not repairable by consult this
manual, contact a technician.
• Keep the operation area of the motorized gate free while the gate in
in motion, and do not create strength to the gate movement.
• Do not perform any operation on mechanical elements or hinges if
the product is in motion.

RESPONSABILITY
• Supplier disclaims any liability if:
• Product failure or deformation result from improper installation

3A
EN
 02. AUTOMATION 02. AUTOMATION
CONNECTION SCHEME TECHNICAL SPECIFICATIONS

24V 230V
• Max. weight of leaf 500Kg
• Max. width of leaf 2,50m
• Motors power supply 24V DC 230V AC
2x1,5mm2 (24V DC) • Motor power 50W 280W
4x1,5mm2 (230V DC)
• Rotational speed 1800 RPM 1400 RPM
2x0,75mm2
4x • Capacitor - 12,5μF
0,75mm2 Photocell TX
Photocell RX • Mechanical unlock for emergency With key
2x0,75mm2
• Operating temperature -25°C/+55°C
4x0,75mm2 • Weight 10Kg
3x1,5mm2 • Protection class IP67
Power supply 230V
• Opening time 90° 16 sec
• Impulse force 250Nm
INSTALLATION MAP
• Motor current consumption 3A 1,5A

DIMENSIONS
3

143,5mm

116mm
4
7 RG58/9 6

220mm
70m
2 m
230V AC 226
mm m
330m

160mm
2
Ø6
2m
m
1

140mm

198mm
340
mm m
410m
8 5

1 • Motor 3 • Flashing lamp 5 • Internal photocell 7 • Key selector 26,45mm

2 • External photocell 4 • Antenna 6 • Electronic control board 8 • Remote control
127,5mm

4A 4B
EN EN
 03. INSTALLATION 03. INSTALLATION
GATE LEAF OPENING ANGLE BOX INSTALLATION
Establish the required opening angle.
1 • Create a hole (taking into account
C1
the dimensions indicated in the
BOX POSITION image) to contain the motor support
PILLAR box (C1).

375mm

INSIDE VIEW 320mm

2 • Insert the tube for water

90°
drainage in the prepared hole (F1).

3 • Insert the tube for the power

cable to pass into the hole (F2).
PILLAR
BOX POSITION

F2 165mm

F1

Note: while positioning the box,

INSIDE VIEW keep in mind the minimum
distance there must be between
the pillar and the centre of rotation
of the gate hinge.

4 • Cement so that the box cannot

110°
be moved, wait for it to dry and 72mm
then assemble the motor and
levers.

Distance between
Pillar and Hinge Axis

5A 5B
EN EN
 03. INSTALLATION 03. INSTALLATION
ASSEMBLING THE MOTOR AND LEVERS MOUNTING THE MOTOR LEVER TO THE GATE

1 • Place the motor in the box and secure it with Place and fix the cover with the screws provided.
the screws provided.

2 • Insert the ball on the box stud and apply the

gate anchor (L1). L1

Position the gate leaf and the lever (L1) so

that they are perfectly aligned and fix them by
BALL welding or another type of fixing.

3 • Put the connection lever (L2) between the

levers (L3) and (L1).
L1

L1

L2 welding
L3

6A 6B
EN EN
 03. INSTALLATION 04. TROUBLESHOOTING
EMERGENCY RELEASE FINAL CONSUMERS AND SPECIALIZED INSTALLERS INSTRUCTIONS

Place the key (C) supplied, in the hole Problem Probable cause Solution
(V), which is located in the lever L1 and
turn it.
• There is no 230V power
• Check main switch
supply

• Control selectors or remote

C controls STOP. If you do not
• Emergency STOP present use STOP, check the bridge at
the STOP contact input on the
control board
L1
• With a remote control or key
V
selector, the gate does not • Replace with one of same
• Fuse blown
open or the motor does not value
work

LIMIT SWITCHES ASSEMBLY (OPTIONAL) • Motor(s) power cable

• Connect the cable to
appropriate terminal or
disconnected or defective
replace
Insert, regulate and block the mechanical limit switches in the desired position.

Closing Opening
• There is an obstacle between
• Check the connection, remove
the photocells or they do not
any obstacle
work

• The gate does not open with • Follow the remote control
• The remote control has not
a remote control, but works recognition procedures on the
been memorised or the battery
with the key selector receiver or replace the battery
is low
with a new one

• Modify the value with the

• Gate starts to open/close, but • The force of the motor(s) is
FORCE button on the control
stops insufficient
board

• Change the polarity of the

• One leaf opens and the other motor cable that is working in
• The connection is not correct
closes the opposite direction to the
correct one

7A 7B
EN EN