4CoreN73PV-HD720p

User Manual

Version 3.1 Published February 2008 Copyright2008 ASRock INC. All rights reserved.

Copyright Notice:
No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners benefit, without intent to infringe.

Disclaimer:
Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. With respect to the contents of this manual, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose. In no event shall ASRock, its directors, officers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the manual or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CALIFORNIA, USA ONLY The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance. Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/perchlorate ASRock Website: http://www.asrock.com

Contents
1 Introduction ................................................... 5
1.1 Package Contents .......................................................... 5 1.2 Specifications ................................................................. 6 1.3 Minimum Hardware Requirement Table for Windows VistaTM Premium 2007 and Basic Logo.......................... 9 1.4 Minimum Hardware Requirement for 720p Blu-ray (BD) / HD-DVD Playback Support ..........................................10 1.5 720p Blu-ray (BD) / HD-DVD Films Which Pass Our Lab Test ................................................................................. 11 1.6 Motherboard Layout ........................................................ 12 1.7 ASRock 6CH DVI I/O ...................................................... 13

2 Installation ..................................................... 14
2.1 Screw Holes ................................................................... 14 2.2 Pre-installation Precautions ............................................ 14 2.3 CPU Installation .............................................................. 15 2.4 Installation of Heatsink and CPU fan ............................... 17 2.5 Installation of Memory Modules (DIMM) ......................... 18 2.6 Expansion Slots (PCI and PCI Express Slots) ..................... 19 2.7 Dual Monitor and Surround Display Features ................ 20 2.8 Jumpers Setup ............................................................... 23 2.9 Onboard Headers and Connectors .................................. 24 2.10 SATAII Hard Disk Setup Guide ....................................... 28 2.11 Serial ATA (SATA) / Serial ATAII (SATAII) Hard Disks Installation .................................................................... 29 2.12 Hot Plug and Hot Swap Functions for SATA / SATAII HDDs........................................................................ 29 2.13 SATA / SATAII HDD Hot Plug Feature and Operation Guide ....................................................................... 30 2.14 Driver Installation Guide .............................................. 32 2.15 Installing Windows XP / XP 64-bit / VistaTM / VistaTM 64-bit Without RAID Functions ............................................. 32 2.15.1 Installing Windows XP / XP 64-bit Without RAID Functions....................................................... 32 2.15.2 Installing Windows VistaTM / VistaTM 64-bit Without RAID Functions....................................................... 33 2.16 Installing Windows XP / XP 64-bit / VistaTM / VistaTM 64-bit With RAID Functions............................... 34 2.16.1 Installing Windows XP / XP 64-bit With RAID Functions....................................................... 34

2.16.2 Installing Windows VistaTM / VistaTM 64-bit With RAID Functions ............................................. 35 2.17 Untied Overclocking Technology .................................. 36

SETUP 3 BIOS S ETUP UTILITY .......................................... 37

3.1 Introduction ..................................................................... 3.1.1 BIOS Menu Bar ..................................................... 3.1.2 Navigation Keys .................................................... 3.2 Main Screen ................................................................... 3.3 Advanced Screen ............................................................ 3.3.1 CPU Configuration ................................................ 3.3.2 Chipset Configuration ............................................ 3.3.3 ACPI Configuration ................................................ 3.3.4 IDE Configuration .................................................. 3.3.5 PCIPnP Configuration ........................................... 3.3.6 Floppy Configuration ............................................. 3.3.7 Super IO Configuration .......................................... 3.3.8 USB Configuration ................................................ 3.4 Hardware Health Event Monitoring Screen ...................... 3.5 Boot Screen ................................................................... 3.5.1 Boot Settings Configuration ................................... 3.6 Security Screen .............................................................. 3.7 Exit Screen .................................................................... 4.1 Install Operating System ................................................ 4.2 Support CD Information ................................................... 4.2.1 Running Support CD ............................................. 4.2.2 Drivers Menu ......................................................... 4.2.3 Utilities Menu ........................................................ 4.2.4 Contact Information ............................................... 37 37 38 38 38 39 41 43 44 46 47 47 49 49 50 51 51 52 53 53 53 53 53 53

4 Software Support .......................................... 53

Chapter 1 Introduction
Thank you for purchasing ASRock 4CoreN73PV-HD720p motherboard, a reliable motherboard produced under ASRocks consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRocks commitment to quality and endurance. In this manual, chapter 1 and 2 contain introduction of the motherboard and step-bystep guide to the hardware installation. Chapter 3 and 4 contain the configuration guide to BIOS setup and information of the Support CD.
Because the motherboard specifications and the BIOS software might be updated, the content of this manual will be subject to change without notice. In case any modifications of this manual occur, the updated version will be available on ASRock website without further notice. You may find the latest VGA cards and CPU support lists on ASRock website as well. ASRock website http://www.asrock.com If you require technical support related to this motherboard, please visit our website for specific information about the model you are using. www.asrock.com/support/index.asp

Pack ackage 1.1 P ack age Contents

ASRock 4CoreN73PV-HD720p Motherboard (Micro ATX Form Factor: 9.6-in x 8.0-in, 24.4 cm x 20.3 cm) ASRock 4CoreN73PV-HD720p Quick Installation Guide ASRock 4CoreN73PV-HD720p Support CD One 80-conductor Ultra ATA 66/100/133 IDE Ribbon Cable One Ribbon Cable for a 3.5-in Floppy Drive One Serial ATA (SATA) Data Cable (Optional) One Serial ATA (SATA) HDD Power Cable (Optional) One ASRock 6CH DVI I/O Panel Shield

1.2

Specifications
- Micro ATX Form Factor: 9.6-in x 8.0-in, 24.4 cm x 20.3 cm - LGA 775 for Intel CoreTM 2 Extreme / CoreTM 2 Quad / CoreTM 2 Duo / Pentium Dual Core / Celeron, supporting Quad Core Yorkfield and Dual Core Wolfdale processors - FSB1333/1066/800/533MHz - Supports Hyper-Threading Technology (see CAUTION 1) - Supports Untied Overclocking Technology (see CAUTION 2) - Supports EM64T CPU - NVIDIA GeForce 7100 / nForce 630i - 2 x DDR2 DIMM slots - Support DDR2 800/667/533 non-ECC, un-buffered memory - Max. capacity of system memory: 4GB (see CAUTION 3) - CPU Frequency Stepless Control (see CAUTION 4) - ASRock U-COP (see CAUTION 5) - Boot Failure Guard (B.F.G.) - 1 x PCI Express x16 slot - 1 x PCI Express x1 slot - 2 x PCI slots - Integrated NVIDIA GeForce 7100 - DX9.0 VGA, Pixel Shader 3.0 - Max. shared memory 256MB (see CAUTION 6) - Dual VGA Output: support DVI-D and D-Sub ports by independent display controllers - Supports HDCP function with DVI-D port - Supports 720p Blu-ray (BD) / HD-DVD playback (see CAUTION 7) - 5.1 CH Windows VistaTM Premium Level HD Audio (ALC662 Audio Codec) - Realtek PHY RTL8201CL - Speed: 10/100 Ethernet - Supports Wake-On-LAN ASRock 6CH_DVI I/O - 1 x PS/2 Mouse Port - 1 x PS/2 Keyboard Port - 1 x VGA/D-Sub Port - 1 x VGA/DVI-D Port - 1 x Parallel Port (ECP/EPP Support) - 4 x Ready-to-Use USB 2.0 Ports

Platform CPU

Chipset Memory

Hybrid Booster

Expansion Slot

Graphics

Audio LAN

Rear Panel I/O

Connector

BIOS Feature

Support CD Hardware Monitor

OS Certifications

- 1 x RJ-45 Port - HD Audio Jack: Line in/Front Speaker/Microphone - 4 x Serial ATAII 3.0Gb/s connectors, support RAID (RAID 0, RAID 1, RAID 0+1, JBOD and RAID 5), NCQ, AHCI and Hot Plug functions (see CAUTION 8) - 1 x ATA133 IDE connector (supports 2 x IDE devices) - 1 x Floppy connector - 1 x DeskExpress Hot Plug Detection header - 1 x COM port header - CPU/Chassis FAN connector - 24 pin ATX power connector - 4 pin 12V power connector - CD in header - Front panel audio connector - 2 x USB 2.0 headers (support 4 USB 2.0 ports) (see CAUTION 9) - 1 x WiFi/E header (see CAUTION 10) - 4Mb AMI BIOS - AMI Legal BIOS - Supports Plug and Play - ACPI 1.1 Compliance Wake Up Events - Supports jumperfree - AMBIOS 2.3.1 Support - Drivers, Utilities, AntiVirus Software (Trial Version) - CPU Temperature Sensing - Chassis Temperature Sensing - CPU Fan Tachometer - Chassis Fan Tachometer - CPU Quiet Fan - Voltage Monitoring: +12V, +5V, +3.3V, CPU Vcore - Microsoft Windows XP / XP 64-bit / VistaTM / VistaTM 64-bit compliant - FCC, CE, WHQL

* For detailed product information, please visit our website: http://www.asrock.com WARNING Please realize that there is a certain risk involved with overclocking, including adjusting the setting in the BIOS, applying Untied Overclocking Technology, or using the thirdparty overclocking tools. Overclocking may affect your system stability, or even cause damage to the components and devices of your system. It should be done at your own risk and expense. We are not responsible for possible damage caused by overclocking.

CAUTION!
1. 2. 3. About the setting of Hyper Threading Technology, please check page 40. This motherboard supports Untied Overclocking Technology. Please read Untied Overclocking Technology on page 36 for details. Due to the operating system limitation, the actual memory size may be less than 4GB for the reservation for system usage under Windows XP and Windows VistaTM. For Windows XP 64-bit and Windows VistaTM 4. 64-bit with 64-bit CPU, there is no such limitation. Although this motherboard offers stepless control, it is not recommended to perform over-clocking. Frequencies other than the recommended CPU bus frequencies may cause the instability of the system or damage the 5. CPU. While CPU overheat is detected, the system will automatically shutdown. Before you resume the system, please check if the CPU fan on the motherboard functions properly and unplug the power cord, then plug it back again. To improve heat dissipation, remember to spray thermal grease between the CPU and the heatsink when you install the PC system. 6. The maximum shared memory size is defined by the chipset vendor and is subject to change. Please check NVIDIA website for the latest information. 720p Blu-ray (BD) / HD-DVD playback support on this motherboard requires the proper hardware configuration. Please refer to page10 and 11 for the minimum hardware requirement and the passed 720p Blu-ray (BD) 8. / HD-DVD films in our lab test. Before installing SATAII hard disk to SATAII connector, please read the SATAII Hard Disk Setup Guide on page 28 to adjust your SATAII hard disk drive to SATAII mode. You can also connect SATA hard disk to SATAII connector 9. directly. Power Management for USB 2.0 works fine under Microsoft Windows

7.

VistaTM 64-bit / VistaTM / XP 64-bit / XP SP1 or SP2. 10. WiFi/E header supports WiFi+AP function with ASRock WiFi-802.11g or WiFi-802.11n module, an easy-to-use wireless local area network (WLAN) adapter. It allows you to create a wireless environment and enjoy the convenience of wireless network connectivity. Please visit our website for the availability of ASRock WiFi-802.11g or WiFi-802.11n module. ASRock website http://www.asrock.com

1.3

Requirement Table Minimum Hardware R equirement Table for TM Windows Vista Premium 2007 and Basic Logo
For system integrators and users who purchase this motherboard and plan to submit Windows VistaTM Premium 2007 and Basic logo, please follow below table for minimum hardware requirements.
CPU Memory VGA Celeron D 326 1GB system memory (Premium) 512MB Single Channel (Basic) DX9.0 with WDDM Driver DVI with HDCP

* If you use onboard VGA with total system memory size 512MB and plan to submit Windows VistaTM Basic logo, please adjust the shared memory size of onboard VGA to 64MB. If you use onboard VGA with total system memory size above 512MB and plan to submit Windows VistaTM Premium or Basic logo, please adjust the shared memory size of onboard VGA to 128MB or above. * If you plan to use external graphics card on this motherboard, please refer to Premium Discrete requirement at http://www.asrock.com * If the onboard VGA supports DVI, it must also support HDCP function to qualify for Windows VistaTM Premium 2007 logo. * After June 1, 2007, all Windows VistaTM systems are required to meet above minimum hardware requirements in order to qualify for Windows VistaTM Premium 2007 logo.

1.4

Minimum Hardware Requirement for 720p Blu-ray HD-D -DVD Support (BD) / HD -D VD Playback Suppor t
720p Blu-ray (BD) / HD-DVD playback support on this motherboard requires the proper hardware configuration. Please refer to below table for the minimum hardware requirement.
CPU VGA Memory Suggested OS Wolfdale E8500 Onboard VGA with DVI-D port DDR2 800, 1GB x 2 Windows VistaTM or Windows VistaTM 64

* If you need to use CyberLink PowerDVD Ultra version 7.2 or 7.3, we suggest to disable Hardware Acceleration function for better playback performance and compatibility. After executing CyberLink PowerDVD Ultra program, please follow below steps to disable Hardware Acceleration function. A. Right-click the main page of CyberLink PowerDVD Ultra program. B. Click Configuration. C. Select Video. D. Click Enable hardware acceleration (nVidia PureVideo) to remove the V mark in this item. E. Click OK to save the change.

10

1.5

-DVD Films P assed 720p Blu-ray (BD) / HD -D VD F ilms in Our Test L ab Test
DVD Film Name Format VC-1 MPEG-2 MPEG-4-AVC MPEG-4-AVC MPEG-4-AVC Producer WB SONY SONY FOX FOX FOX UNIVERSAL UNIVERSAL WEA TERWILLIGER

Type Blu-ray SWORDFISH DVD UNDERWORLD EVOLUTION CASINO ROYALE THE LAST STAND SPEED

THE LEAGUE OF MPEG-4-AVC EXTRAORDINARY GENTLEMEN HDDVD KING KONG THE INTERPRETER NEW ORLEANS CONCERT ONE SIX RIGHT VC-1 MPEG-4-AVC MPEG-2 MPEG-2

* MPEG-4-AVC mentioned above refers to the same format of H.264. * Above passed films are tested under below configuration. Items Configurations CPU VGA Memory OS Playback Software DVD Player Wolfdale E8500 Onboard VGA with DVI-D port DDR2 800, 1GB x 2 Windows VistaTM or Windows VistaTM 64 CyberLink PowerDVD Ultra Pioneer BDR-101A / LG GBW-H10N (BD) HP HD100 (HD-DVD)

11

1.6 Motherboard Layout

1 2 3
20.3cm (8.0 in)

5 6

HDCP

DDRII_1 (64 bit, 240-pin module)

DDRII_2 (64 bit, 240-pin module)

28
USB 2.0 T: USB0 B: USB1
Top: RJ-45
1 1

USB4_5

DVI
NVIDIA GeForce 7100 / nForce 630i Chipset
4Mb BIOS

Wolfdale FSB1333

Yorkfield

USB 2.0 T: USB2 B: USB3

PCI

27

DDR2 800

USB6_7

Quad Core CPU

EXPRESS

IDE1

24.4cm (9.6 in)

PS2 Keyboard

PS2 Mouse
1
PS2_USB_PWR1

CPU_FAN1

ATX12V1

ATXPWR1

DVI_CON1 VGA1
Bottom: MIC IN

PARALLEL PORT
Top: LINE IN Center: FRONT

24

SATAII

26 25
LAN PHY

PCIE1

4CoreN73PV-HD720p
PCIE2
1
CLRCMOS1

9
Super I/O

COM1

CHA_FAN1

WIFI/E
AUDIO CODEC

IR1

FLOPPY1
SPEAKER1

RAID
20

19

18

17 16 15 14 13 12

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

PS2_USB_PWR1 Jumper 16 ATX Power Connector (ATXPWR1) 17 ATX 12V Connector (ATX12V1) 18 775-Pin CPU Socket 19 CPU Fan Connector (CPU_FAN1) North Bridge Controller 20 2 x 240-pin DDR2 DIMM Slots 21 (DDRII_1 and DDRII_2; Yellow) 22 IDE1 Connector (IDE1, Blue) 23 Serial Port Connector (COM1) 24 Clear CMOS Jumper (CLRCMOS1) 25 System Panel Header (PANEL1) 26 Fourth SATAII Connector (SATAII_4 (PORT1.3)) 27 Third SATAII Connector (SATAII_3 (PORT1.2)) 28 Secondary SATAII Connector (SATAII_2 (PORT1.1)) Primary SATAII Connector (SATAII_1 (PORT1.0))

Chassis Fan Connector (CHA_FAN1) Chassis Speaker Header (SPEAKER 1) Floppy Connector (FLOPPY1) DeskExpress Hot Plug Detection Header (IR1) WiFi/E Header (WIFI/E) Front Panel Audio Header (HD_AUDIO1) PCI Slots (PCI1 - 2) Internal Audio Connector: CD1 (Black) PCI Express x16 Slot (PCIE2) SPI Flash Memory (4Mb) PCI Express x1 Slot (PCIE1) USB 2.0 Header (USB6_7, Blue) USB 2.0 Header (USB4_5, Blue)

12

SATAII_1 (PORT1.0) SATAII_2 (PORT1.1) SATAII_3 (PORT1.2) SATAII_4 (PORT1.3)

23 22 21

CD1

RoHS

PCI1

10
PLED PWRBTN

CMOS Battery

PANEL1

HD_AUDIO1

HDLED

RESET

11

PCI2

1.7

ASRock 6CH_DVI I/O

3 4 5 6

11
1 2 3 4 5 *6

10

9
7 8 9 10 11

PS/2 Mouse Port (Green) Parallel Port RJ-45 Port Line In (Light Blue) Front Speaker (Lime) Microphone (Pink)

USB 2.0 Ports (USB23) USB 2.0 Ports (USB01) VGA/D-Sub Port VGA/DVI-D Port PS/2 Keyboard Port (Purple)

* To enable Multi-Streaming function, you need to connect a front panel audio cable to the front panel audio header. Please refer to below steps for the software setting of Multi-Streaming. For Windows XP: After restarting your computer, you will find Mixer tool on your system. Please select Mixer ToolBox , click Enable playback multi-streaming, and click ok. Choose 2CH or

4CH and then you are allowed to select Realtek HDA Primary output to use Rear Speaker and Front Speaker, or select Realtek HDA Audio 2nd output to use front panel audio. Then reboot your system. For Windows VistaTM: After restarting your computer, please double-click Realtek HD Audio Manager on the system tray. Set Speaker Configuration to Quadraphonic or Stereo. Click Device advanced settings, choose Make front and rear output devices playbacks two different audio streams simultaneously, and click ok. Then reboot your system.

13

Chapter 2 Installation
4CoreN73PV-HD720p is a Micro ATX form factor (9.6" x 8.0", 24.4 x 20.3 cm) motherboard. Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it.
Make sure to unplug the power cord before installing or removing the motherboard. Failure to do so may cause physical injuries to you and damages to motherboard components.

2.1 Screw Holes

Place screws into the holes indicated by circles to secure the motherboard to the chassis.
Do not over-tighten the screws! Doing so may damage the motherboard.

2.2 Pre-installation Precautions

Take note of the following precautions before you install motherboard components or change any motherboard settings. 1. Unplug the power cord from the wall socket before touching any component. 2. To avoid damaging the motherboard components due to static electricity, NEVER place your motherboard directly on the carpet or the like. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle components. 3. Hold components by the edges and do not touch the ICs. 4. Whenever you uninstall any component, place it on a grounded antistatic pad or in the bag that comes with the component.
Before you install or remove any component, ensure that the power is switched off or the power cord is detached from the power supply. Failure to do so may cause severe damage to the motherboard, peripherals, and/or components.

14

2.3 CPU Installation

For the installation of Intel 775-LAND CPU, please follow the steps below.

775-Pin Socket Overview Before you insert the 775-LAND CPU into the socket, please check if the CPU surface is unclean or if there is any bent pin on the socket. Do not force to insert the CPU into the socket if above situation is found. Otherwise, the CPU will be seriously damaged.

Step 1. Open the socket: Step 1-1. Disengaging the lever by depressing down and out on the hook to clear retention tab.

Step 1-2. Rotate the load lever to fully open position at approximately 135 degrees. Step 1-3. Rotate the load plate to fully open position at approximately 100 degrees. Step 2. Insert the 775-LAND CPU: Step 2-1. Hold the CPU by the edges where are marked with black lines.

black line

black line

Step 2-2. Orient the CPU with IHS (Integrated Heat Sink) up. Locate Pin1 and the two orientation key notches.
Pin1 orientation key notch orientation key notch Pin1 alignment key alignment key

775-Pin Socket 775-LAND CPU

15

For proper inserting, please ensure to match the two orientation key notches of the CPU with the two alignment keys of the socket.

Step 2-3. Carefully place the CPU into the socket by using a purely vertical motion. Step 2-4. Verify that the CPU is within the socket and properly mated to the orient keys. Step 3. Remove PnP Cap (Pick and Place Cap): Use your left hand index finger and thumb to support the load plate edge, engage PnP cap with right hand thumb and peel the cap from the socket while pressing on center of PnP cap to assist in removal.
1. It is recommended to use the cap tab to handle and avoid kicking off the PnP cap. 2. This cap must be placed if returning the motherboard for after service.

Step 4. Close the socket: Step 4-1. Rotate the load plate onto the IHS. Step 4-2. While pressing down lightly on load plate, engage the load lever. Step 4-3. Secure load lever with load plate tab under retention tab of load lever.

16

2.4

Installation of CPU Fan and Heatsink

This motherboard is equipped with 775-Pin socket that supports Intel 775-LAND CPU. Please adopt the type of heatsink and cooling fan compliant with Intel 775-LAND CPU to dissipate heat. Before you installed the heatsink, you need to spray thermal interface material between the CPU and the heatsink to improve heat dissipation. Ensure that the CPU and the heatsink are securely fastened and in good contact with each other. Then connect the CPU fan to the CPU_FAN connector (CPU_FAN1, see page 12, No. 5). For proper installation, please kindly refer to the instruction manuals of your CPU fan and heatsink. Below is an example to illustrate the installation of the heatsink for 775-LAND CPU. Step 1. Apply thermal interface material onto center of IHS on the socket surface.

Step 2.

Step 3. Step 4.

Place the heatsink onto the socket. Ensure fan cables are oriented on side closest to the CPU fan connector on the motherboard (CPU_FAN1, see page 12, No. 5). Align fasteners with the motherboard throughholes. Rotate the fastener clockwise, then press down on fastener caps with thumb to install and lock. Repeat with remaining fasteners.

If you press down the fasteners without rotating them clockwise, the heatsink cannot be secured on the motherboard.

Step 5. Step 6.

Connect fan header with the CPU fan connector on the motherboard. Secure excess cable with tie-wrap to ensure cable does not interfere with fan operation or contact other components.

17

2.5 Installation of Memor y Modules (DIMM)

This motherboard provides two 240-pin DDR2 (Double Data Rate 2) DIMM slots.
Please make sure to disconnect power supply before adding or removing DIMMs or the system components.

Step 1. Step 2.

Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the slot such that the notch on the DIMM matches the break on the slot.

notch break

notch break

The DIMM only fits in one correct orientation. It will cause permanent damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.

Step 3.

Firmly insert the DIMM into the slot until the retaining clips at both ends fully snap back in place and the DIMM is properly seated.

18

2.6 Expansion Slots (PCI and PCI Express Slots)

There are 2 PCI slots and 2 PCI Express slots on this motherboard. PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI interface. PCIE slots: PCIE1 (PCIE x1 slot) is used for PCI Express cards with x1 lane width cards, such as Gigabit LAN card, SATA2 card, etc. PCIE2 (PCIE x16 slot) is used for PCI Express cards with x16 lane width graphics cards.

Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the power supply is switched off or the power cord is unplugged. Please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation. Remove the bracket facing the slot that you intend to use. Keep the screws for later use. Align the card connector with the slot and press firmly until the card is completely seated on the slot. Fasten the card to the chassis with screws.

Step 2. Step 3. Step 4.

19

2.7 Dual Monitor and Surround Display Features

Dual Monitor Feature This motherboard supports dual monitor feature. With the internal dual VGA output support (DVI-D and D-Sub), you can easily enjoy the benefits of dual monitor feature without installing any add-on VGA card to this motherboard. This motherboard also provides independent display controllers for DVI-D and D-Sub to support dual VGA output so that DVI-D and D-sub can drive same or different display contents. To enable dual monitor feature, please follow the below steps: 1. Connect the DVI-D monitor cable to the VGA/DVI-D port on the I/O panel of this motherboard. Connect the D-Sub monitor cable to the VGA/D-Sub port on the I/O panel of this motherboard.

VGA/DVI-D port

VGA/D-Sub port

2. If you have installed onboard VGA driver from our support CD to your system already, you can freely enjoy the benefits of dual monitor function provided by VGA/DVI-D and VGA/D-Sub ports with this motherboard after your system boots. If you havent installed onboard VGA driver yet, please install onboard VGA driver from our support CD to your system and restart your computer. Then you can start to use dual monitor function provided by VGA/DVI-D and VGA/D-Sub ports with this motherboard.
When you playback HDCP-protected video from Blu-ray (BD) or HD-DVD disc, the content will be displayed only in one of the two monitors instead of both monitors.

20

Surround Display Feature This motherboard supports surround display upgrade. With the internal dual VGA output support (DVI-D and D-Sub) and the external add-on PCI Express VGA card, you can easily enjoy the benefits of surround display feature. Please refer to the following steps to set up a surround display environment: 1. Install the NVIDIA PCI Express VGA card to PCIE2 slot. Please refer to page 19 for proper expansion card installation procedures for details. 2. Connect the DVI-D monitor cable to the VGA/DVI-D port on the I/O panel of this motherboard. Connect the D-Sub monitor cable to the VGA/D-Sub port on the I/O panel of this motherboard. 3. Boot your system. Press <F2> to enter BIOS setup. Enter Share Memory option to adjust the memory capability to [32MB], [64MB], [128MB] or [256MB] to enable the function of VGA/D-sub. Please make sure that the value you select is less than the total capability of the system memory. If you do not adjust the BIOS setup, the default value of Share Memory, [Auto], will disable VGA/D-Sub function when the add-on VGA card is inserted to this motherboard. 4. Install the onboard VGA driver and the add-on PCI Express VGA card driver to your system. If you have installed the onboard VGA driver and the add-on PCI Express VGA card driver already, there is no need to install them again. 5. Set up a multi-monitor display. For Windows XP / XP 64-bit OS: Right click the desktop, choose Properties, and select the Settings tab so that you can adjust the parameters of the multi-monitor according to the steps below. A. Click the Identify button to display a large number on each monitor. B. Right-click the display icon in the Display Properties dialog that you wish to be your primary monitor, and then select Primary. When you use multiple monitors with your card, one monitor will always be Primary, and all additional monitors will be designated as Secondary. C. Select the display icon identified by the number 2. D. Click Extend my Windows desktop onto this monitor. E. Right-click the display icon and select Attached, if necessary. F. Set the Screen Resolution and Color Quality as appropriate for the second monitor. Click Apply or OK to apply these new values. G. Repeat steps C through E for the diaplay icon identified by the number one, two, three and four. For Windows VistaTM / VistaTM 64-bit OS: Right click the desktop, choose Personalize, and select the Display Settings tab so that you can adjust the parameters of the multi-monitor according to the steps below.

21

A. Click the number 2 icon. B. Click the items This is my main monitor and Extend the desktop onto this monitor. C. Click OK to save your change. D. Repeat steps A through C for the display icon identified by the number three and four. 6. Use Surround Display. Click and drag the display icons to positions representing the physical setup of your monitors that you would like to use. The placement of display icons determines how you move items from one monitor to another.

HDCP Function with DVI-D Port HDCP function is supported with DVI-D port on this motherboard. To use HDCP function with this motherboard, you need to adopt the monitor that supports HDCP function as well. Therefore, you can enjoy the superior display quality with high-definition HDCP encryption contents. Please refer to below instruction for more details about HDCP function. What is HDCP? HDCP stands for High-Bandwidth Digital Content Protection, a specification developed by Intel for protecting digital entertainment content that uses the DVI interface. HDCP is a copy protection scheme to eliminate the possibility of intercepting digital data midstream between the video source, or transmitter - such as a computer, DVD player or set-top box - and the digital display, or receiver - such as a monitor, television or projector. In other words, HDCP specification is designed to protect the integrity of content as it is being transmitted. Products compatible with the HDCP scheme such as DVD players, satellite and cable HDTV set-top-boxes, as well as few entertainment PCs requires a secure connection to a compliant display. Due to the increase in manufacturers employing HDCP in their equipment, it is highly recommended that the HDTV or LCD monitor you purchase is compatible.

22

2.8 Jumpers Setup

The illustration shows how jumpers are setup. When the jumper cap is placed on pins, the jumper is Short. If no jumper cap is placed on pins, the jumper is Open. The illustration shows a 3-pin jumper whose pin1 and pin2 are Short when jumper cap is placed on these 2 pins. Jumper Setting PS2_USB_PWR1 2_3 1_2

Description Short pin2, pin3 to enable (see p.12 No. 1) +5VSB (standby) for PS/2 +5V +5VSB or USB wake up events. Note: To select +5VSB, it requires 2 Amp and higher standby current provided by power supply. Clear CMOS Jumper
(CLRCMOS1) (see p.12 No. 10)

1_2

2_3

Default

Clear CMOS

Note: CLRCMOS1 allows you to clear the data in CMOS. The data in CMOS includes system setup information such as system password, date, time, and system setup parameters. To clear and reset the system parameters to default setup, please turn off the computer and unplug the power cord from the power supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3 on CLRCMOS1 for 5 seconds. However, please do not clear the CMOS right after you update the BIOS. If you need to clear the CMOS when you just finish updating the BIOS, you must boot up the system first, and then shut it down before you do the clearCMOS action.

23

2.9 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard!

FDD connector
(33-pin FLOPPY1) (see p.12 No. 18)
Pin1 FLOPPY1

the red-striped side to Pin1

Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the connector. Primary IDE connector (Blue)
(39-pin IDE1, see p.12 No. 8)

PIN1

IDE1

connect the blue end to the motherboard

connect the black end to the IDE devices

80-conductor ATA 66/100133 cable Note: Please refer to the instruction of your IDE device vendor for the details. Serial ATAII Connectors
SATAII_1 (PORT1.0) SATAII_2 (PORT1.1) SATAII_3 (PORT1.2)

see p.12, No. 15) (SATAII_2 (PORT1.1): see p.12, No. 14) (SATAII_3 (PORT1.2): see p.12, No. 13) (SATAII_4 (PORT1.3): see p.12, No. 12)

Serial ATA (SATA) Data Cable

(Optional)

SATAII_4 (PORT1.3)

(SATAII_1 (PORT1.0):

These four Serial ATAII (SATAII) connectors support SATA data cables for internal storage devices. The current SATAII interface allows up to 3.0 Gb/s data transfer rate.

Either end of the SATA data cable can be connected to the SATA / SATAII hard disk or the SATAII connector on this motherboard.

24

Serial ATA (SATA) Power Cable

(Optional)
connect to the SATA HDD power connector connect to the power supply

Please connect the black end of SATA power cable to the power connector on each drive. Then connect the white end of SATA power cable to the power connector of the power supply. Besides four default USB 2.0 ports on the I/O panel, there are two USB 2.0 headers on this motherboard. Each USB 2.0 header can support two USB 2.0 ports.

USB 2.0 Headers

(9-pin US6_7) (see p.12 No. 27)
1

USB_PWR P-7 P+7 GND DUMMY

GND P+6 P-6 USB_PWR

(9-pin USB4_5) (see p.12 No. 28)

USB_PWR P-5 P+5 GND DUMMY 1 GND P+4 P-4 USB_PWR

WiFi/E Header
(15-pin WIFI/E) (see p.12 No. 20)
1

USB+5V_2 TXN TXP GND2 PCIE_RST# +3SVB RXN RXP

PexCLK GND1 PexCLK# D0- D0+ PME# USB+5V_1

This header supports WiFi+AP function with ASRock WiFi-802.11g or WiFi-802.11n module, an easy-to-use wireless local area network (WLAN) adapter. It allows you to create a wireless environment and enjoy the convenience of wireless network connectivity. This header supports the Hot Plug detection function for ASRock DeskExpress.

DeskExpress Hot Plug Detection Header

(5-pin IR1) (see p.12 No. 19)
1

IRTX +5VSB Hotplug#

GND IRRX

Internal Audio Connectors

(4-pin CD1) (CD1: see p.12 No. 23)
CD-L GND GND CD-R

CD1

This connector allows you to receive stereo audio input from sound sources such as a CD-ROM, DVD-ROM, TV tuner card, or MPEG card.

25

Front Panel Audio Header

(9-pin HD_AUDIO1) (see p.12 No. 21)
1

GND PRESENCE# MIC_RET OUT_RET

This is an interface for front panel audio cable that allows convenient connection and control of audio devices.

OUT2_L J_SENSE OUT2_R MIC2_R MIC2_L

1. High Definition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instruction in our manual and chassis manual to install your system. 2. If you use AC97 audio panel, please install it to the front panel audio header as below: A. Connect Mic_IN (MIC) to MIC2_L. B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L. C. Connect Ground (GND) to Ground (GND). D. MIC_RET and OUT_RET are for HD audio panel only. You dont need to connect them for AC97 audio panel. E. Enter BIOS Setup Utility. Enter Advanced Settings, and then select Chipset Configuration. Set the Front Panel Control option from [Auto] to [Enabled]. F. Enter Windows system. Click the icon on the lower right hand taskbar to enter Realtek HD Audio Manager. For Windows XP / XP 64-bit OS: Click Audio I/O, select Connector Settings , choose

Disable front panel jack detection, and save the change by clicking OK. For Windows VistaTM / VistaTM 64-bit OS: Click the right-top Folder icon , choose Disable front panel jack detection, and save the change by clicking OK.

System Panel Header

(9-pin PANEL1) (see p.12 No. 11)
1

PLED+ PLEDPWRBTN# GND

This header accommodates several system front panel functions.

DUMMY RESET# GND HDLEDHDLED+

Chassis Speaker Header

(4-pin SPEAKER 1) (see p.12 No. 17)

1
SPEAKER DUMMY DUMMY +5V

Please connect the chassis speaker to this header.

26

Chassis Fan Connector

(3-pin CHA_FAN1) (see p.12 No. 16)
GND +12V CHA_FAN_SPEED

Please connect a chassis fan cable to this connector and match the black wire to the ground pin. Please connect a CPU fan cable to this connector and match the black wire to the ground pin.

CPU Fan Connector

(4-pin CPU_FAN1) (see p.12 No. 5)

4321

GND +12V CPU_FAN_SPEED FAN_SPEED_CONTROL

Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin CPU fan still can work successfully even without the fan speed control function. If you plan to connect the 3-Pin CPU fan to the CPU fan connector on this motherboard, please connect it to Pin 1-3.
Pin 1-3 Connected 3-Pin Fan Installation

ATX Power Connector

(24-pin ATXPWR1) (see p.12 No. 2)

12

24

Please connect an ATX power supply to this connector.

13 12 24

Though this motherboard provides 24-pin ATX power connector, it can still work if you adopt a traditional 20-pin ATX power supply. To use the 20-pin ATX power supply, please plug your power supply along with Pin 1 and Pin 13.
20-Pin ATX Power Supply Installation

13

ATX 12V Connector

(4-pin ATX12V1) (see p.12 No. 3)

Please connect an ATX 12V power supply to this connector.

Serial port Header

(9-pin COM1) (see p.12 No. 9)
1

RRXD1 DDTR#1 DDSR#1 CCTS#1

This COM1 header supports a serial port module.

RRI#1 RRTS#1 GND TTXD1 DDCD#1

27

SAT 2.10 SATAII Hard Disk Setup Guide

Before installing SATAII hard disk to your computer, please carefully read below SATAII hard disk setup guide. Some default setting of SATAII hard disks may not be at SATAII mode, which operate with the best performance. In order to enable SATAII function, please follow the below instruction with different vendors to correctly adjust your SATAII hard disk to SATAII mode in advance; otherwise, your SATAII hard disk may fail to run at SATAII mode. Western Digital
7 8 5 6 3 4 1 2

If pin 5 and pin 6 are shorted, SATA 1.5Gb/s will be enabled. On the other hand, if you want to enable SATAII 3.0Gb/s, please remove the jumpers from pin 5 and pin 6. SAMSUNG
7 8 5 6 3 4 1 2

If pin 3 and pin 4 are shorted, SATA 1.5Gb/s will be enabled. On the other hand, if you want to enable SATAII 3.0Gb/s, please remove the jumpers from pin 3 and pin 4. HITACHI Please use the Feature Tool, a DOS-bootable tool, for changing various ATA features. Please visit HITACHIs website for details: http://www.hitachigst.com/hdd/support/download.htm

The above examples are just for your reference. For different SATAII hard disk products of different vendors, the jumper pin setting methods may not be the same. Please visit the vendors website for the updates.

28

2.11

AT (SAT AT (SAT Serial ATA (SATA) / Serial ATAII (SATAII) Hard Disks Installation

This motherboard adopts NVIDIA GeForce 7100 / nForce 630i chipset that supports Serial ATA (SATA) / Serial ATAII (SATAII) hard disks and RAID functions. You may install SATA / SATAII hard disks on this motherboard for internal storage devices. This section will guide you to install the SATA / SATAII hard disks. STEP 1: Install the SATA / SATAII hard disks into the drive bays of your chassis. STEP 2: Connect the SATA power cable to the SATA / SATAII hard disk. STEP 3: Connect one end of the SATA data cable to the motherboards SATAII connector. STEP 4: Connect the other end of the SATA data cable to the SATA / SATAII hard disk.

2 . 1 2 Hot Plug and Hot Swap Functions for SATA / SATAII Functions SAT SAT HDDs
This motherboard supports Hot Plug and Hot Swap functions for SATA / SATAII Devices in RAID / AHCI mode. NVIDIA GeForce 7100 / nForce 630i chipset provides hardware support for Advanced Host controller Interface (AHCI), a new operation interface for SATA host controllers developed thru a joint industry effort. AHCI also provides usability enhancements such as Hot Plug. NOTE What is Hot Plug Function?
If the SATA / SATAII HDDs are NOT set for RAID configuration, it is called Hot Plug for the action to insert and remove the SATA / SATAII HDDs while the system is still power-on and in working condition. However, please note that it cannot perform Hot Plug if the OS has been installed into the SATA / SATAII HDD.

What is Hot Swap Function?

If SATA / SATAII HDDs are built as RAID 1 or RAID 5 then it is called Hot Swap for the action to insert and remove the SATA / SATAII HDDs while the system is still power-on and in working condition.

29

SAT SAT Feature 2.13 SATA / SATAII HDD Hot Plug F eature and Operation Guide
This motherboard supports Hot Plug feature for SATA / SATAII HDD in RAID / AHCI mode. Please read below operation guide of SATA / SATAII HDD Hot Plug feature carefully. Before you process the SATA / SATAII HDD Hot Plug, please check below cable accessories from the motherboard gift box pack. A. 7-pin SATA data cable B. SATA power cable with SATA 15-pin power connector interface A. SATA data cable (Red) B. SATA power cable

SATA 7-pin connector

The SATA 15-pin power connector (Black) connect to SATA / SATAII HDD

1x4-pin conventional power connector (White) connect to power supply

Caution
1. Without SATA 15-pin power connector interface, the SATA / SATAII Hot Plug cannot be processed. 2. Even some SATA / SATAII HDDs provide both SATA 15-pin power connector and IDE 1x4-pin conventional power connector interfaces, the IDE 1x4-pin conventional power connector interface is definitely not able to support Hot Plug and will cause the HDD damage and data loss.

Points of attention, before you process the Hot Plug:

1. Below operation procedure is designed only for our motherboard, which supports SATA / SATAII HDD Hot Plug. * The SATA / SATAII Hot Plug feature might not be supported by the chipset because of its limitation, the SATA / SATAII Hot Plug support information of our motherboard is indicated in the product spec on our website: www.asrock.com 2. Make sure your SATA / SATAII HDD can support Hot Plug function from your dealer or HDD user manual. The SATA / SATAII HDD, which cannot support Hot Plug function, will be damaged under the Hot Plug operation. 3. Please make sure the SATA / SATAII driver is installed into system properly. The latest SATA / SATAII driver is available on our support website: www.asrock.com 4. Make sure to use the SATA power cable & data cable, which are from our motherboard package. 5. Please follow below instructions step by step to reduce the risk of HDD crash or data loss.

30

How to Hot Plug a SATA / SATAII HDD:

Points of attention, before you process the Hot Plug: Please do follow below instruction sequence to process the Hot Plug, improper procedure will cause the SATA / SATAII HDD damage and data loss.
Step 1 Please connect SATA power cable 1x4-pin end Step 2 Connect SATA data cable to the motherboards SATAII connector. (White) to the power supply 1x4-pin cable.

SATA power cable 1x4-pin power connector (White)

Step 3 Connect SATA 15-pin power cable connector (Black) end to SATA / SATAII HDD.

Step 4 Connect SATA data cable to the SATA / SATAII HDD.

How to Hot Unplug a SATA / SATAII HDD:

Points of attention, before you process the Hot Unplug: Please do follow below instruction sequence to process the Hot Unplug, improper procedure will cause the SATA / SATAII HDD damage and data loss.
Step 1 Unplug SATA data cable from SATA / SATAII HDD side.

Step 2 Unplug SATA 15-pin power cable connector (Black) from SATA / SATAII HDD side.

31

2 . 1 4 Driver Installation Guide

To install the drivers to your system, please insert the support CD to your optical drive first. Then, the drivers compatible to your system can be auto-detected and listed on the support CD driver page. Please follow the order from up to bottom side to install those required drivers. Therefore, the drivers you install can work properly.

2 . 1 5 Installing Windows XP / XP 64-bit / Vista TM / Vista TM Without Functions 64-bit W ithout RAID Functions
If you want to install Windows XP, Windows XP 64-bit, Windows VistaTM or Windows VistaTM 64-bit on your SATA / SATAII HDDs without RAID functions, please follow below procedures according to the OS you install.

2.15.1 Installing Windows XP / XP 64-bit Without RAID Functions Functions

If you want to install Windows XP / Windows XP 64-bit on your SATA / SATAII HDDs without RAID functions, please follow below steps. Using SATA / SATAII HDDs with NCQ and Hot Plug functions STEP 1: Set Up BIOS. A. Enter BIOS SETUP UTILITY Advanced screen IDE Configuration. B. Set the SATA Operation Mode option to [AHCI]. STEP 2: Make a SATA / SATAII driver diskette. A. Insert the ASRock Support CD into your optical drive to boot your system. (There are two ASRock Support CD in the motherboard gift box pack, please choose the one for Windows XP / XP 64-bit.) B. During POST at the beginning of system boot-up, press <F11> key, and then a window for boot devices selection appears. Please select CD-ROM as the boot device. C. When you see the message on the screen, Generate Serial ATA driver diskette [YN]?, press <Y>. D. Then you will see these messages, Please choose: 1. Generate AHCI Driver diskette for WindowsXP 2. Generate RAID Driver diskette for WindowsXP 3. Generate AHCI Driver diskette for WindowsXP64 4. Generate RAID Driver diskette for WindowsXP64 5. Exit Reboot system now Press any key to continue

32

Please insert a floppy diskette into the floppy drive. Select your required item on the list according to the mode you choose and the OS you install. Then press any key. E. The system will start to format the floppy diskette and copy SATA / SATAII drivers into the floppy diskette. STEP 3: Install Windows XP / XP 64-bit OS on your system. After making a SATA / SATAII driver diskette, you can start to install Windows XP / XP 64-bit on your system. At the beginning of Windows setup, press F6 to install a thirdparty AHCI driver. When prompted, insert the SATA / SATAII driver diskette containing the NVIDIA AHCI driver. After reading the floppy disk, the driver will be presented. Select the driver to install according to the OS you install. The drivers are as below:
A. NVIDIA nForce Storage Controller (required) Windows XP B. NVIDIA nForce Storage Controller (required) Windows XP64

Please select A for Windows XP in AHCI mode. Please select B for Windows XP 64-bit in AHCI mode. Using SATA / SATAII HDDs without NCQ and Hot Plug functions STEP 1: Set Up BIOS. A. Enter BIOS SETUP UTILITY Advanced screen IDE Configuration. B. Set the SATA Operation Mode option to [non-RAID]. STEP 2: Install Windows XP / XP 64-bit OS on your system.

2.15.2 Installing Windows Vista TM / Vista TM 64-bit Without Functions W ithout RAID Functions
If you want to install Windows VistaTM / Windows VistaTM 64-bit on your SATA / SATAII HDDs without RAID functions, please follow below steps. Using SATA / SATAII HDDs with NCQ and Hot Plug functions STEP 1: Set Up BIOS. A. Enter BIOS SETUP UTILITY Advanced screen IDE Configuration. B. Set the SATA Operation Mode option to [AHCI]. STEP 2: Install Windows VistaTM / VistaTM 64-bit OS on your system. Insert the Windows VistaTM / Windows VistaTM 64-bit optical disk into the optical drive to boot your system, and follow the instruction to install Windows VistaTM / Windows VistaTM 64-bit OS on your system. When you see Where do you want to install Windows? page, please insert the ASRock Support CD into your optical drive, and click the Load Driver button on the left on the bottom to load the NVIDIA AHCI drivers. NVIDIA AHCI drivers are in the following path in our Support CD:

33

(There are two ASRock Support CD in the motherboard gift box pack, please choose the one for Windows VistaTM / VistaTM 64-bit.) .. \ I386 \ AHCI_Vista (For Windows VistaTM OS) .. \ AMD64\ AHCI_Vista64 (For Windows VistaTM 64-bit OS) After that, please insert Windows VistaTM / Windows VistaTM 64-bit optical disk into the optical drive again to continue the installation. Using SATA / SATAII HDDs without NCQ and Hot Plug functions STEP 1: Set Up BIOS. A. Enter BIOS SETUP UTILITY Advanced screen IDE Configuration. B. Set the SATA Operation Mode option to [non-RAID]. STEP 2: Install Windows VistaTM / VistaTM 64-bit OS on your system. Insert the Windows VistaTM / Windows VistaTM 64-bit optical disk into the optical drive to boot your system, and follow the instruction to install Windows VistaTM / Windows VistaTM 64-bit OS on your system.

2 . 1 6 Installing Windows XP / XP 64-bit / Vista TM / Vista TM With Functions 64-bit W ith RAID Functions
If you want to install Windows XP, Windows XP 64-bit, Windows VistaTM or Windows VistaTM 64-bit on your SATA / SATAII HDDs with RAID functions, please follow below procedures according to the OS you install.

2.16.1 Installing Windows XP / XP 64-bit With RAID Functions Functions

If you want to install Windows XP / Windows XP 64-bit on your SATA / SATAII HDDs with RAID functions, please follow below steps. STEP 1: Set Up BIOS. A. Enter BIOS SETUP UTILITY Advanced screen IDE Configuration. B. Set the SATA Operation Mode option to [RAID]. STEP 2: Make a SATA / SATAII driver diskette. Please make a SATA / SATAII driver diskette by following section 2.15.1 step 2 on page 32. STEP 3: Use RAID Installation Guide to set RAID configuration. Before you start to configure RAID function, you need to check the RAID installation guide in the Support CD for proper configuration. Please refer to the BIOS RAID installation guide part of the document in the following path in the Support CD: .. \ RAID Installation Guide

34

STEP 4: Install Windows XP / XP 64-bit OS on your system. After step1, 2, 3, you can start to install Windows XP / Windows XP 64-bit OS on your system. At the beginning of Windows setup, press F6 to install a third-party RAID driver. When prompted, insert the SATA / SATAII driver diskette containing the NVIDIA RAID driver. After reading the floppy disk, the drivers will be presented. Select the drivers to install. The drivers are as below:
A. NVIDIA RAID Driver (required) B. NVIDIA nForce Storage Controller (required)

Please select A and B for Windows XP / XP 64-bit in RAID mode. (There are two RAID drivers needed for RAID mode, you have to select them separately. Please specify the first RAID driver and then specify again for the second one.)
NOTE. If you install Windows XP / Windows XP 64-bit on IDE HDDs and want to manage (create, convert, delete, or rebuild) RAID functions on SATA / SATAII HDDs, you still need to set up SATA Operation Mode to [RAID] in BIOS first. Then, please set the RAID configuration by using the Windows RAID installation guide part of the docu ment in the following path in the Support CD: .. \ RAID Installation Guide

2.16.2 Installing Windows Vista TM / Vista TM 64-bit With Functions RAID Functions
If you want to install Windows VistaTM / Windows VistaTM 64-bit on your SATA / SATAII HDDs with RAID functions, please follow below steps. STEP 1: Set Up BIOS. A. Enter BIOS SETUP UTILITY Advanced screen IDE Configuration. B. Set the SATA Operation Mode option to [RAID]. STEP 2: Use RAID Installation Guide to set RAID configuration. Before you start to configure RAID function, you need to check the RAID installation guide in the Support CD for proper configuration. Please refer to the BIOS RAID installation guide part of the document in the following path in the Support CD: .. \ RAID Installation Guide STEP 3: Install Windows VistaTM / VistaTM 64-bit OS on your system. Insert the Windows VistaTM / Windows VistaTM 64-bit optical disk into the optical drive to boot your system, and follow the instruction to install Windows VistaTM / Windows VistaTM 64-bit OS on your system. When you see Where do you want to install Windows? page, please insert the ASRock Support CD into your optical drive, and click the Load Driver button on the left on the bottom to load the NVIDIA RAID drivers. NVIDIA RAID drivers are in the following path in our Support CD: (There are two ASRock Support CD in the motherboard gift box pack, please choose the one for Windows VistaTM / VistaTM 64-bit.) .. \ I386 \ RAID_Vista (For Windows VistaTM OS) .. \ AMD64\ RAID_Vista64 (For Windows VistaTM 64-bit OS)

35

After that, please insert Windows VistaTM / Windows VistaTM 64-bit optical disk into the optical drive again to continue the installation.
NOTE. If you install Windows VistaTM / Windows VistaTM 64-bit on IDE HDDs and want to manage (create, convert, delete, or rebuild) RAID functions on SATA / SATAII HDDs, you still need to set up SATA Operation Mode to [RAID] in BIOS first. Then, please set the RAID configuration by using the Windows RAID installation guide in the following path in the Support CD: .. \ RAID Installation Guide

Technology 2 . 1 7 Untied Overclocking Technology

This motherboard supports Untied Overclocking Technology, which means during overclocking, FSB enjoys better margin due to fixed PCI / PCIE buses. Before you enable Untied Overclocking function, please enter Overclock Mode option of BIOS setup to set the selection from [Auto] to [CPU, PCIE, Async.]. Therefore, CPU FSB is untied during overclocking, but PCI / PCIE buses are in the fixed mode so that FSB can operate under a more stable overclocking environment.
Please refer to the warning on page 7 for the possible overclocking risk before you apply Untied Overclocking Technology.

36

Chapter 3 BIOS SETUP UTILITY

3.1 Introduction
This section explains how to use the BIOS SETUP UTILITY to configure your system. The BIOS SPI chip on the motherboard stores the BIOS SETUP UTILITY. You may run the BIOS SETUP UTILITY when you start up the computer. Please press <F2> during the Power-On-Self-Test (POST) to enter the BIOS SETUP UTILITY, otherwise, POST will continue with its test routines. If you wish to enter the BIOS SETUP UTILITY after POST, restart the system by pressing <Ctl> + <Alt> + <Delete>, or by pressing the reset button on the system chassis. You may also restart by turning the system off and then back on. Because the BIOS software is constantly being updated, the following BIOS setup screens and descriptions are for reference purpose only, and they may not exactly match what you see on your screen.

3.1.1 BIOS Menu Bar

The top of the Main Advanced H/W Monitor Boot screen has a menu bar with the following selections: To set up the system time/date information To set up the advanced BIOS features To display current hardware status To set up the default system device to locate and load the Operating System Security To set up the security features Exit To exit the current screen or the BIOS SETUP UTILITY Use < > key or < > key to choose among the selections on the menu bar, and then press <Enter> to get into the sub screen.

37

3.1.2 Navigation Keys

Please check the following table for the function description of each navigation key. Navigation Key(s) / / + / <Enter> <F1> <F9> <F10> <ESC> Function Description Moves cursor left or right to select Screens Moves cursor up or down to select items To change option for the selected items To bring up the selected screen To display the General Help Screen To load optimal default values for all the settings To save changes and exit the BIOS SETUP UTILITY To jump to the Exit Screen or exit the current screen

3.2 Main Screen

When you enter the BIOS SETUP UTILITY, the Main screen will appear and display the system overview
Advanced BIOS SETUP UTILITY H/W Monitor Boot Security Exit

Main

System Overview
System Time System Date BIOS Version Processor Type [14:00:09] [Thu 01/10/2007]

Use [Enter], [TAB] or [SHIFT-TAB] to select a field. Use [+] or [-] to configure system Time.

: 4CoreN73PV-HD720p P1.00 : Intel (R) Core (TM) 2 Quad CPU Q9300 @ 2.50GHz (64bit) : 2500MHz Processor Speed Microcode Update : 10676/606 : 6144KB Cache Size Total Memory DDRII 1 DDRII 2 : 2048MB with 256MB shared memory : 1024MB/266MHz (DDRII533) : 1024MB/266MHz (DDRII533)

+Tab F1 F9 F10 ESC

Select Screen Select Item Change Field Select Field General Help Load Defaults Save and Exit Exit

v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.

System Time [Hour:Minute:Second] Use this item to specify the system time. System Date [Day Month/Date/Year] Use this item to specify the system date.

3.3 Advanced Screen

In this section, you may set the configurations for the following items: CPU Configuration, Chipset Configuration, ACPI Configuration, IDE Configuration, PCIPnP Configuration, Floppy Configuration, SuperIO Configuration, and USB Configuration.

38

Main

Advanced

BIOS SETUP UTILITY H/W Monitor Boot

Security
Configure CPU

Exit

Advanced Settings
WARNING : Setting wrong values in below sections may cause system to malfunction. CPU Configuration Chipset Configuration ACPI Configuration IDE Configuration PCIPnP Configuration Floppy Configuration SuperIO Configuration USB Configuration

Enter F1 F9 F10 ESC

Select Screen Select Item Go to Sub Screen General Help Load Defaults Save and Exit Exit

v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.

Setting wrong values in this section may cause the system to malfunction.

3 . 3 . 1 CPU Configuration
BIOS SETUP UTILITY Advanced CPU Configuration
Overclock Mode CPU Frequency (MHz) Boot Failure Guard CPU Spread Spectrum PCIE Spread Spectrum SATAII Spread Spectrum Ratio Actual Value Enhanced Halt State Max CPUID Value Limit Intel Virtualization tech. CPU Thermal Throttling No-Excute Memory Protection Hyper Threading Technology Intel (R) SpeedStep (tm) tech. [Auto] [333] [Enabled] [Disabled] [Disabled] [Disabled] 7.5 [Disabled] [Disabled] [Enabled] [Enabled] [Disabled] [Enabled] [Disabled] Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit Select the over clock mode.

+F1 F9 F10 ESC

v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.

Overclock Mode Use this to select Overclock Mode. The default value is [Auto]. Configuration options: [Auto], [CPU, PCIE, Sync.] and [CPU, PCIE, Async.]. CPU Frequency (MHz) Use this option to adjust CPU frequency. Boot Failure Guard Enable or disable the feature of Boot Failure Guard. CPU Spread Spectrum This feature will be set to [Disabled] as default. Configuration options: [Disabled] and [Auto].

39

PCIE Spread Spectrum This feature will be set to [Disabled] as default. Configuration options: [Disabled] and [Enabled]. SATA Spread Spectrum This feature will be set to [Disabled] as default. Configuration options: [Disabled] and [Enabled]. Ratio Actual Value This is a read-only item, which displays the ratio actual value of this motherboard. Enhance Halt State All processors support the Halt State (C1). The C1 state is supported through the native processor instructions HLT and MWAIT and requires no hardware support from the chipset. In the C1 power state, the processor maintains the context of the system caches. Max CPUID Value Limit For Prescott CPU only, some OSes (ex. NT4.0) cannot handle the function with disable. This should be enabled in order to boot legacy OSes that cannot support CPUs with extended CPUID functions. Intel (R) Virtualization tech. When this option is set to [Enabled], a VMM (Virtual Machine Architecture) can utilize the additional hardware capabilities provided by Vanderpool Technology. This option will be hidden if the installed CPU does not support Intel (R) Virtualization Technology. CPU Thermal Throttling You may select [Enabled] to enable P4 CPU internal thermal control mechanism to keep the CPU from overheated. No-Excute Memory Protection No-Execution (NX) Memory Protection Technology is an enhancement to the IA-32 Intel Architecture. An IA-32 processor with No Execute (NX) Memory Protection can prevent data pages from being used by malicious software to execute code. This option will be hidden if the current CPU does not support No-Excute Memory Protection. Hyper Threading Technology To enable this feature, it requires a computer system with an Intel Pentium 4 processor that supports Hyper-Threading technology and an operating system that includes optimization for this technology, such as Microsoft Windows XP. Set to [Enabled] if using Microsoft Windows XP, or Linux kernel version 2.4.18 or higher. This option will be hidden if the installed CPU does not support Hyper-Threading technology. Intel (R) SpeedStep(tm) tech. Intel (R) SpeedStep(tm) tech. is Intels new power saving technology. Processor can switch between multiple frequency and voltage points to enable power

40

savings. The default value is [Auto]. Configuration options: [Auto], [Enabled] and [Disabled]. If you install Windows XP and select [Auto], you need to set the Power Schemes as Portable/Laptop to enable this function. If you install Windows VistaTM and want to enable this function, please set this item to [Enabled]. This item will be hidden if the current CPU does not support Intel (R) SpeedStep(tm) tech..
Please note that enabling this function may reduce CPU voltage and lead to system stability or compatibility issue with some power supplies. Please set this item to [Disable] if above issue occurs.

3.3.2 Chipset Configuration

BIOS SETUP UTILITY Advanced Chipset Configuration
DRAM Frequency Flexibility Option Memory Timings OnBoard GPU Clock Share Memory Primary Graphics Adapter Onboard LAN OnBoard HD Audio Front Panel DRAM Voltage VTT Voltage VDDQ Voltage [Auto] [Disabled] [Auto] [Auto] [Auto] [PCI] [Enabled] [Auto] [Auto] [Auto] [Auto] [Auto] +F1 F9 F10 ESC Options Auto 266MHz (DDRII533) 333MHz (DDRII667) 400MHz (DDRII800) Manual

Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit

v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.

DRAM Frequency If [Auto] is selected, the motherboard will detect the memory module(s) inserted and assigns appropriate frequency automatically. You may also select other value as operating frequency: [266MHz (DDRII533)], [333MHz (DDRII667)] and [400MHz (DDRII800)]. Flexibility Option The default value of this option is [Disabled]. It will allow better tolerance for memory compatibility when it is set to [Enabled]. Memory Timings Use this to adjust values for memory timings. Configuration options: [Auto] and [Manual]. The default value is [Auto]. OnBoard GPU Clock Use this option to adjust onboard GPU clock. Configuration options: [Auto] and [Manual]. The default value is [Auto]. Share Memory This allows you to set share memory feature. The default value is [Auto]. Configuration options: [Auto], [32MB], [64MB], [128MB] and [256MB].

41

Primary Graphics Adapter This item will switch the PCI Bus scanning order while searching for video card. It allows you to select the type of Primary VGA in case of multiple video controllers. The default value of this feature is [PCI]. Configuration options: [PCI], [Onboard] and [PCI Express]. Onboard LAN This allows you to enable or disable the onboard LAN feature. OnBoard HD Audio Select [Auto], [Enabled] or [Disabled] for the onboard HD Audio feature. If you select [Auto], the onboard HD Audio will be disabled when PCI Sound Card is plugged. Front Panel Select [Auto], [Enabled] or [Disabled] for the onboard HD Audio Front Panel. DRAM Voltage Use this to select DRAM Voltage. Configuration options: [Auto], [1.85V], [1.90V], [1.95V], [2.00V] and [2.05V]. The default value of this feature is [Auto]. VTT Voltage Use this to select VTT Voltage. Configuration options: [Auto], [1.24V], [1.31V], [1.375V] and [1.42V]. The default value of this feature is [Auto]. VDDQ Voltage Use this to select VTT Voltage. Configuration options: [Auto], [1.24V], [1.31V], [1.375V] and [1.42V]. The default value of this feature is [Auto].

42

3 . 3 . 3 ACPI Configuration
BIOS SETUP UTILITY Advanced ACPI Settings
Suspend To RAM Repost Video on STR Resume Check Ready Bit Restore on AC / Power Loss PCI Devices Power On PS / 2 Keyboard Power On RTC Alarm Power On ACPI HPET Table [Auto] [No] [Enabled] [Power Off] [Disabled] [Disabled] [Disabled] [Disabled] +F1 F9 F10 ESC Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit Select auto-detect or disable the STR feature.

v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.

Suspend to RAM Use this item to select whether to auto-detect or disable the Suspend-toRAM feature. Select [Auto] will enable this feature if the OS supports it. If you set this item to [Disabled], the functions Repost Video on STR Resume and Check Ready Bit will be hidden. Repost Video on STR Resume This feature allows you to repost video on STR resume. (STR refers to suspend to RAM.) Check Ready Bit Use this item to enable or disable the feature Check Ready Bit. Restore on AC/Power Loss This allows you to set the power state after an unexpected AC/power loss. If [Power Off] is selected, the AC/power remains off when the power recovers. If [Power On] is selected, the AC/power resumes and the system starts to boot up when the power recovers. PCI Devices Power On Use this item to enable or disable PCI devices to turn on the system from the power-soft-off mode. PS/2 Keyboard Power On Use this item to enable or disable PS/2 keyboard to turn on the system from the power-soft-off mode. RTC Alarm Power On Use this item to enable or disable RTC (Real Time Clock) to power on the system.

43

ACPI HPET Table Use this item to enable or disable ACPI HPET Table. The default value is [Disabled]. Please set this option to [Enabled] if you plan to use this motherboard to submit Windows VistaTM certification.

3 . 3 . 4 IDE Configuration
BIOS SETUP UTILITY Advanced IDE Configuration
OnBoard IDE Controller OnBoard SATA Controller SATA Operation Mode IDE1 Master IDE1 Slave SATAII_1 SATAII_2 SATAII_3 SATAII_4 [Enabled] [Enabled] [non-RAID] [Hard Disk] [Not Detected] [Not Detected] [Not Detected] [Not Detected] [Not Detected] +F1 F9 F10 ESC To enable or disable the onboard IDE controller.

Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit

v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.

OnBoard IDE Controller Use this item to enable or disable the OnBoard IDE Controller feature. OnBoard SATA Controller Use this item to enable or disable the OnBoard SATA Controller feature. SATA Operation Mode Use this item to adjust SATA Operation Mode. The default value of this option is [non-RAID]. If you want to operate RAID function on SATA / SATAII HDDs, please select [RAID]. Configuration options: [non-RAID], [RAID] and [AHCI].
* If you select [RAID] mode, SATA / SATAII HDDs can not be accessed until you finish configuring RAID functions in NVIDIA BIOS / Windows RAID Utility.

IDE Device Configuration You may set the IDE configuration for the device that you specify. We will use the IDE1 Master as the example in the following instruction, which can be applied to the configurations of IDE1 Slave as well.

44

BIOS SETUP UTILITY Advanced Primary IDE Master

Device Vendor Size LBA Mode Block Mode PIO Mode Async DMA Ultra DMA S.M.A.R.T. Type LBA/Large Mode Block (Multi-Sector Transfer) PIO Mode DMA Mode S.M.A.R.T. 32Bit Data Transfer :Hard Disk :ST340014A :40.0 GB :Supported :16Sectors :4 :MultiWord DMA-2 :Ultra DMA-5 :Supported [Auto] [Auto] [Auto] [Auto] [Auto] [Disabled] [Enabled]

Select the type of device connected to the system.

+F1 F9 F10 ESC

Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit

v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.

TYPE Use this item to configure the type of the IDE device that you specify. Configuration options: [Not Installed], [Auto], [CD/DVD], and [ARMD]. [Not Installed]: Select [Not Installed] to disable the use of IDE device. [Auto]: Select [Auto] to automatically detect the hard disk drive.
After selecting the hard disk information into BIOS, use a disk utility, such as FDISK, to partition and format the new IDE hard disk drives. This is necessary so that you can write or read data from the hard disk. Make sure to set the partition of the Primary IDE hard disk drives to active.

[CD/DVD]:This is used for IDE CD/DVD drives. [ARMD]: This is used for IDE ARMD (ATAPI Removable Media Device), such as MO. LBA/Large Mode Use this item to select the LBA/Large mode for a hard disk > 512 MB under DOS and Windows; for Netware and UNIX user, select [Disabled] to disable the LBA/Large mode. Block (Multi-Sector Transfer) The default value of this item is [Auto]. If this feature is enabled, it will enhance hard disk performance by reading or writing more data during each transfer. PIO Mode Use this item to set the PIO mode to enhance hard disk performance by o p timizing the hard disk timing. DMA Mode DMA capability allows the improved transfer-speed and data-integrity for compatible IDE devices.

45

DMA Mode DMA capability allows the improved transfer-speed and data-integrity for compatible IDE devices. S.M.A.R.T. Use this item to enable or disable the S.M.A.R.T. (Self-Monitoring, Analysis, and Reporting Technology) feature. Configuration options: [Disabled], [Auto], [Enabled]. 32-Bit Data Transfer Use this item to enable 32-bit access to maximize the IDE hard disk data transfer rate.

3 . 3 . 5 PCIPnP Configuration
BIOS SETUP UTILITY Advanced Advanced PCI / PnP Settings
PCI Latency Timer PCI IDE BusMaster [32] [Enabled] Value in units of PCI clocks for PCI device latency timer register.

+F1 F9 F10 ESC

Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit

v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.

PCI Latency Timer The default value is 32. It is recommended to keep the default value unless the installed PCI expansion cards specifications require other settings. PCI IDE BusMaster Use this item to enable or disable the PCI IDE BusMaster feature.

46

3.3.6 Floppy Configuration

In this section, you may configure the type of your floppy drive.
BIOS SETUP UTILITY Advanced Floppy Configuration
Floppy A [1.44 MB 31 2"] Select the type of floppy drive connected to the system.

+F1 F9 F10 ESC

Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit

v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.

3.3.7 Super IO Configuration

BIOS SETUP UTILITY Advanced Configure Super IO Chipset
OnBoard Floppy Controller Serial Port Address Infrared Port Address Parallel Port Address Parallel Port Mode EPP Version ECP Mode DMA Channel Parallel Port IRQ [Enabled] [3F8 / IRQ4] [Disabled] [378] [ECP + EPP] [1.9] [DMA3] [IRQ7] Allow BIOS to Enable or Disable Floppy Controller.

+F1 F9 F10 ESC

Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit

v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.

OnBoard Floppy Controller Use this item to enable or disable floppy drive controller. Serial Port Address Use this item to set the address for the onboard serial port or disable it. Configuration options: [Disabled], [3F8 / IRQ4], [2F8 / IRQ3], [3E8 / IRQ4], [2E8 / IRQ3]. Infrared Port Address Use this item to set the address for the onboard infrared port or disable it. Configuration options: [Disabled], [2F8 / IRQ3], and [2E8 / IRQ3]. If you plan to use ASRock DeskExpress on this motherboard, please keep this item on [Disabled] option.

47

Parallel Port Address Use this item to set the address for the onboard parallel port or disable it. Configuration options: [Disabled], [378], and [278]. Parallel Port Mode Use this item to set the operation mode of the parallel port. The default value is [ECP+EPP]. If this option is set to [ECP+EPP], it will show the EPP version in the following item, EPP Version. Configuration options: [Normal], [Bi-Directional], and [ECP+EPP]. EPP Version Use this item to set the EPP version. Configuration options: [1.9] and [1.7]. ECP Mode DMA Channel Use this item to set the ECP mode DMA channel. Configuration options: [DMA0], [DMA1], and [DMA3]. Parallel Port IRQ Use this item to set the IRQ for the parallel port. Configuration options: [IRQ5] and [IRQ7].

48

3 . 3 . 8 USB Configuration
BIOS SETUP UTILITY Advanced USB Configuration
USB Controller USB 2.0 Support Legacy USB Support [Enabled] [Enabled] [Disabled] To enable or disable the onboard USB controllers.

+F1 F9 F10 ESC

Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit

v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.

USB Controller Use this item to enable or disable the use of USB controller. USB 2.0 Support Use this item to enable or disable the USB 2.0 support. Legacy USB Support Use this item to enable or disable the support to emulate legacy I/O devices such as mouse, keyboard,... etc. Or you may select [Auto] so that the system will start to auto-detect; if there is no USB device connected, Auto option will disable the legacy USB support.

3.4 Hardware Health Event Monitoring Screen

In this section, it allows you to monitor the status of the hardware on your system, including the parameters of the CPU temperature, motherboard temperature, CPU fan speed, chassis fan speed, and the critical voltage.
BIOS SETUP UTILITY Boot H/W Monitor

Main

Advanced

Security
Enable/Disable CPU Quiet Fan Function.

Exit

Hardware Health Event Monitoring

CPU Temperature M / B Temperature CPU Fan Speed Chassis Fan Speed Vcore + 3.30V + 5.00V + 12.00V CPU Quiet Fan : 37 C / 98 F : 31 C / 87 F : 3400 RPM : N/A : : : : 1.629V 3.306V 5.067V 11.890V [Disabled]

F1 F9 F10 ESC

Select Screen Select Item General Help Load Defaults Save and Exit Exit

v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.

49

CPU Quiet Fan This item allows you to identify the temperature of CPU fan. If you set this option as [Disabled], the CPU fan will operate in full speed. If you set this option as [Enabled], you will find the items Target CPU Temperature ( C), Tolerance ( C), and Minimun Fan Speed appear to allow you adjusting them. The default value is [Disabled]. You are allowed to enable this function only when you install 4-pin CPU fan. Target CPU Temperature ( C) The target temperature will be between 45 C and 65 C. The default value is [50]. Tolerance ( C) The default value of tolerance is [2], which means the error of the target CPU temperature will be within 2 C. Target Fan Speed Use this option to set the target fan speed. You can freely adjust the target fan speed according to the target CPU temperature that you choose. The default value is [Fast]. Configuration options: [Fast], [Middle] and [Slow].

3.5 Boot Screen

In this section, it will display the available devices on your system for you to configure the boot settings and the boot priority.
Main Advanced BIOS SETUP UTILITY H/W Monitor Boot Security Exit

Boot Settings
Boot Settings Configuration 1st Boot Device 2nd Boot Device 3rd Boot Device 4th Boot Device Hard Disk Drives Removable Drives CD/DVD Drives [1st Floppy Device] [HDD: PM - HDS722580VL] [CD / DVD: 3S - CD - ROM C] [USB]

Configure Settings during System Boot.

Enter F1 F9 F10 ESC

Select Screen Select Item Go to Sub Screen General Help Load Defaults Save and Exit Exit

v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.

50

3.5.1 Boot Settings Configuration

BIOS SETUP UTILITY Boot Boot Settings Configuration
Boot From Onboard LAN Bootup Num-Lock [Disabled] [On] To enable or disable the boot from onboard LAN feature.

+F1 F9 F10 ESC

Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit

v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.

Boot From Onboard LAN Use this item to enable or disable the Boot From Onboard LAN feature. Boot Up Num-Lock If this item is set to [On], it will automatically activate the Numeric Lock function after boot-up.

3.6 Security Screen

In this section, you may set or change the supervisor/user password for the system. For the user password, you may also clear it.
BIOS SETUP UTILITY H/W Monitor Boot

Main

Advanced

Security

Exit

Security Settings
Supervisor Password User Password : Not Installed : Not Installed

Install or Change the password.

Change Supervisor Password Change User Password

Enter F1 F9 F10 ESC

Select Screen Select Item Change General Help Load Defaults Save and Exit Exit

v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.

51

3.7 Exit Screen

Main Exit Options
Save Changes and Exit Discard Changes and Exit Discard Changes Load Optimal Defaults

Advanced

BIOS SETUP UTILITY H/W Monitro Boot

Security
Exit system setup after saving the changes.

Exit

F10 key can be used for this operation.

Enter F1 F9 F10 ESC

Select Screen Select Item Go to Sub Screen General Help Load Defaults Save and Exit Exit

v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.

Save Changes and Exit When you select this option, it will pop-out the following message, Save configuration changes and exit setup? Select [OK] to save the changes and exit the BIOS SETUP UTILITY. Discard Changes and Exit When you select this option, it will pop-out the following message, Discard changes and exit setup? Select [OK] to exit the BIOS SETUP UTILITY without saving any changes. Discard Changes When you select this option, it will pop-out the following message, Discard changes? Select [OK] to discard all changes. Load Optimal Defaults When you select this option, it will pop-out the following message, Load optimal defaults? Select [OK] to load the default values for all the setup configurations.

52

Support Chapter 4 Software Suppor t

4 . 1 Install Operating System This motherboard supports various Microsoft Windows operating systems: XP / XP 64-bit / VistaTM / VistaTM 64-bit. Because motherboard settings and hardware options vary, use the setup procedures in this chapter for general reference only. Refer to your OS documentation for more information. 4 . 2 Support CD Information The Support CD that came with the motherboard contains necessary drivers and useful utilities that enhance the motherboard features. 4 . 2 . 1 Running The Support CD To begin using the support CD, insert the CD into your CD-ROM drive. The CD automatically displays the Main Menu if AUTORUN is enabled in your computer. If the Main Menu did not appear automatically, locate and double click on the file ASSETUP.EXE from the BIN folder in the Support CD to display the menus. 4 . 2 . 2 Drivers Menu The Drivers Menu shows the available devices drivers if the system detects installed devices. Please install the necessary drivers to activate the devices. 4 . 2 . 3 Utilities Menu The Utilities Menu shows the applications software that the motherboard supports. Click on a specific item then follow the installation wizard to install it. 4.2.4 Contact Information If you need to contact ASRock or want to know more about ASRock, welcome to visit ASRocks website at http://www.asrock.com; or you may contact your dealer for further information.

53

NOTE.
If you install the VGA driver (version 163.91) on your system, but the window is not in full screen mode, please follow below steps to adjust the window. 1. Right-click the desktop and select NVIDIA Control Panel. 2. Click Display and click Change Flat Panel Scaling. 3. In the option When using a resolution lower than my displays native resolution, please select Use my displays built-in scaling.

54