EZ-LIGHT® Touch Gen 2 K50 Series Pick-to-Light

Datasheet
Compact, Single-Point Devices for Error-Proofing of Bin-Picking Operations
• Excellent immunity to false triggering by water spray, detergents, oils, and other foreign
materials
• Rugged, cost-effective and easy-to-install solutions for error-proofing and parts-
verification applications
• Compact devices are completely self contained—no controller needed
• Waterproof IEC IP69K construction for washdown environments
• Easy actuation—no force required
• 12 V dc to 30 V dc operation
• Can be actuated with bare hands or gloves
• Compact models available for lower profile applications

Standard Model Compact Model

WARNING: Not To Be Used for Personnel Protection

Never use this device as a sensing device for personnel protection. Doing so could lead to serious injury or death. This device
does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. A sensor failure
or malfunction can cause either an energized or de-energized sensor output condition.

Models
Model1 Function Output Connection Job Light

K50APT2GXDQ PNP, N.O.

K50RPT2GXDQ • Job light is illuminated at all times while job input is active PNP, N.C.
Green
K50ANT2GXDQ • Touch activates output NPN, N.O.

K50RNT2GXDQ NPN, N.C.

K50APT2GRCQ PNP, N.O.

K50RPT2GRCQ • Job light is Green while job input is active PNP, N.C. Integral 4-pin M12/Euro-
• Touch activates output and overrides job light (turns Red) for visual style male quick Green (Red)
K50ANT2GRCQ verification that action was sensed NPN, N.O. disconnect (QD)

K50RNT2GRCQ NPN, N.C.

K50APT2GREQ PNP, N.O.

• Job light is Green at all times while job input is active
K50RPT2GREQ PNP, N.C.
• Touch activates output
Green (Red)
• A touch while job input is inactive causes unit to light Red, providing
K50ANT2GREQ NPN, N.O.
visual verification that sensor is functioning properly
K50RNT2GREQ NPN, N.C.

Wiring Diagrams
NPN PNP Color Key

1 1 1 = Brown
+ +
12-30V dc 2 = White
3 12-30V dc 3
– – 3 = Blue
4
4 = Black
4 Load
Load
2 Job Light 2 Job Light
Enable < 1.0V dc Enable > 7V dc

Note: Cabled wiring diagrams are shown. Quick disconnect (QD) wiring diagrams are functionally identical.

1 • To order the 2 m (6.5 ft) PVC cable model, omit the suffix "Q" in the model number. For example, K50APT2GXD.
• To order a compact model, add the suffix "C'" after K50 in the model number. For example, K50CAPT2GXDQ.
• Models with a quick disconnect require a mating cordset.

Original Document 23 June 2017

189828 Rev. D

189828
 EZ-LIGHT® Touch Gen 2 K50 Series Pick-to-Light

Specifications
Supply Voltage Indicators
12 V to 30 V dc Job (pick) indicator: Green
Pick sensed indicator: Red or unilluminated, depending on model
Supply Current
< 75 mA max current at 12 V dc (exclusive of load) Indicator Lumens
< 50 mA max current at 30 V dc (exclusive of load)
Supply Protection Circuitry Color Typical Wavelength Typical Intensity (lm)
Protected against reverse polarity and transient voltages Green 525 nm 29
Output Rating
Maximum load: 150 mA Red 625 nm 13
ON-state saturation voltage: < 2 V dc at 10 mA; < 2.5 V dc at 150 mA
OFF-state leakage current: <10 µA at 30 V dc
Output Response Time Mounting
50 milliseconds On and Off M30 × 1.5 threaded base max. torque 4.5 N·m (40 in·lbf)

Operating Conditions Required Overcurrent Protection

Temperature: –40 °C to +50 °C (–40 °F to +122 °F)
Humidity: 90% at 50 °C maximum relative humidity (non-condensing) WARNING: Electrical connections must be made by
qualified personnel in accordance with local and
Environmental Rating national electrical codes and regulations.
IEC IP67, IP69K per DIN 40050-9.
Cabled models also meet IP69K if the cable and cable entrance are protected from high- Overcurrent protection is required to be provided by end product application per the
pressure spray. supplied table.
Construction Overcurrent protection may be provided with external fusing or via Current Limiting,
Class 2 Power Supply.
Housing: polycarbonate Supply wiring leads < 24 AWG shall not be spliced.
Translucent dome: polycarbonate For additional product support, go to www.bannerengineering.com.
Mounting nut: PBT
Vibration and Mechanical Shock Supply Wiring (AWG) Required Overcurrent Protection (Amps)
Vibration 10 Hz to 55 Hz 1.0 mm p-p amplitude per IEC 60068-2-6
Shock 30G 11 ms duration, half sine wave per IEC 60068-2-27 20 5.0
Power-Up Delay 22 3.0
300 milliseconds
24 2.0
Connections
Integral 4-pin M12/Euro style QD, or 2 m (6.5 ft) PVC integral cable 26 1.0
Storage
28 0.8
–40 °C to +70 °C (–40 °F to +158 °F)
Certifications 30 0.5

Dimensions
Standard Models Compact Models

35 mm
17 mm
[1.38”]
[0.67”]
55 mm
[2.17”] 37.0 mm
[1.46”] 48.0 mm
66 mm [1.89”]
[2.6”]

Ø50 mm M30 x 1.5

[1.97”] Ø50 mm
[1.97”]
M12 x 1

All measurements are listed in millimeters [inches], unless noted otherwise.

2 www.bannerengineering.com - Tel: +1-763-544-3164 P/N 189828 Rev. D

EZ-LIGHT® Touch Gen 2 K50 Series Pick-to-Light

Accessories
Cordsets
4-Pin Threaded M12/Euro-Style Cordsets

Model Length Style Dimensions Pinout (Female)

MQDC-406 1.83 m (6 ft)

44 Typ.
MQDC-415 4.57 m (15 ft)

MQDC-430 9.14 m (30 ft) Straight

M12 x 1
MQDC-450 15.2 m (50 ft) ø 14.5 2
1
MQDC-406RA 1.83 m (6 ft)
3
32 Typ. 4
MQDC-415RA 4.57 m (15 ft) [1.26"]
1 = Brown
MQDC-430RA 9.14 m (30 ft)
30 Typ. 2 = White
Right-Angle [1.18"] 3 = Blue
4 = Black
MQDC-450RA 15.2 m (50 ft) M12 x 1
ø 14.5 [0.57"]

Brackets

SMB30A 45 SMB30FA 83.2

• Right-angle bracket with curved slot • Swivel bracket with tilt and pan
for versatile orientation movement for precise adjustment
C
• Clearance for M6 (¼ in) hardware • Mounting hole for 30 mm sensor
61
• Mounting hole for 30 mm sensor • 12-ga. 304 stainless steel
• 12-ga. stainless steel B • Easy sensor mounting to extrude rail 36.3 68.9
T-slot B
A
• Metric and inch size bolt available A
69

Hole center spacing: A to B=40 Bolt thread: SMB30FA, A= 3/8 - 16 x 2 in; SMB30FAM10, A= M10 - 1.5 x 50
Hole size: A=ø 6.3, B= 27.1 x 6.3, C=ø 30.5 Hole size: B= ø 30.1

SMB30FVK SMB30MM
• V-clamp, flat bracket and fasteners • 12-ga. stainless steel bracket with
for mounting to pipe or extensions curved mounting slots for versatile 70 57
46
• Clamp accommodates 28 mm dia. 118 orientation
tubing or 1 in. square extrusions • Clearance for M6 (¼ in) hardware C
• 30 mm hole for mounting sensors A • Mounting hole for 30 mm sensor 57
B

Hole size: A= ø 31 Hole center spacing: A = 51, A to B = 25.4

Hole size: A = 42.6 x 7, B = ø 6.4, C = ø 30.1

SMB30RAVK SMB30SC 67
• V-clamp, right-angle bracket and A • Swivel bracket with 30 mm mounting
fasteners for mounting sensors to hole for sensor B
pipe or extrusion • Black reinforced thermoplastic
• Clamp accommodates 28 mm dia. 46 polyester 58
tubing or 1 in. square extrusions • Stainless steel mounting and swivel
• 30 mm hole for mounting sensors locking hardware included

57 90
29
A

Hole size: A = ø 30.5 Hole center spacing: A=ø 50.8

Hole size: A=ø 7.0, B=ø 30.0

P/N 189828 Rev. D www.bannerengineering.com - Tel: +1-763-544-3164 3

 EZ-LIGHT® Touch Gen 2 K50 Series Pick-to-Light

SMBAMS30P 45 SMBAMS30RA
• Flat SMBAMS series bracket • Right-angle SMBAMS series bracket 45
• 30 mm hole for mounting sensors C • 30 mm hole for mounting sensors C
• Articulation slots for 90°+ rotation • Articulation slots for 90°+ rotation
53
• 12-ga. 300 series stainless steel A • 12-ga. (2.6 mm) cold-rolled steel A
93
B
B

48

Hole center spacing: A=26.0, A to B=13.0 Hole center spacing: A=26.0, A to B=13.0
Hole size: A=26.8 x 7.0, B=ø 6.5, C=ø 31.0 Hole size: A=26.8 x 7.0, B=ø 6.5, C=ø 31.0

TC-K50-CL ØA
• Touch cover

Diameter: A = 67 mm
Height: B = 42.5 mm

Banner Engineering Corp. Limited Warranty

Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any
product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the
improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR
ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO
USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner
Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such purposes
will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product warranties. All specifications published in this document are subject
to change; Banner reserves the right to modify product specifications or update documentation at any time. Specifications and product information in English supersede that which is provided in any other language.
For the most recent version of any documentation, refer to: www.bannerengineering.com.

FCC Part 15 and CAN ICES-3 (B)/NMB-3(B)

This device complies with part 15 of the FCC Rules and CAN ICES-3 (B)/NMB-3(B). Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules and CAN ICES-3 (B)/NMB-3(B). These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the manufacturer.

© Banner Engineering Corp. All rights reserved