Button Panel Maintenance 3-77
Installing OLED The OLED Button Panel will probably ship with OLED Graphics installed. If necessary, however,
Graphics from this section describes the installation of the Button Panel Controller Board OLED Graphics and the
Laptop (if Button Panel Module OLED Graphics from a laptop via a USB cable connection.
necessary)
ESD: Observe all appropriate safety and ESD precautions listed in Preventing Injury and Damage in
the About this Guide chapter.
Installing Controller Board OLED Graphics
Complete the following steps to select, install, and verify the OLED Button Panel Controller Board
OLED Graphics:
1 Ensure that the AC Line Cord is connected to the Power Entry Assembly to ensure proper
grounding.
2 Connect the Button Panel to the Laptop using one of the following methods:
If you have an extra USB Cable, disconnect the existing USB connection to the Button Panel
and connect the Button Panel to the laptop with the extra USB Cable.
If you do not have an extra USB Cable, disconnect the OLED Button Panel USB Cable from
the CPU, Figure 3-129 (A), remove it from the cable clamps, and connect it to the laptop.
Figure 3-129 USB Cable connected to CPU Enclosure (left) and version with USB Connector Cover
Plate (right).
A B
If you are installing the Button Panel onto a game with an Ethernet/USB Cover,
Figure 3-129 (B), reference the Technical Service Bulletin 16-020293-xx: CPU-NXT
Enclosure Ethernet/USB Covers for the steps to access the USB Port.
3 Turn the game ON at the Power Switch in order to power the OLED Button Panel during the
OLED Graphics installation.
4 On the laptop, open the WMS_USBTestCommTool_Vx_xx_setup.exe zip file that was
downloaded earlier.
16-022128-05
3-78 Chapter 3: Maintenance
5 In the zip file window that displays, open the installation file (also called
WMS_USBTestCommTool_Vx_xx_setup.exe).
The Installation Wizard opens, Figure 3-130.
Figure 3-130 Installation Wizard.
6 Complete the Installation Wizard sequence by selecting Next each time you are prompted,
Figure 3-130 (A).
7 When the Installation Wizard sequence is completed, locate the file WMS USB Test Comm
Tool on the Desktop folder of the laptop. The icon for this file is shown in Figure 3-131.
Figure 3-131 WMS USB Test Comm Tool icon.
If you are unable to locate the WMS USB Test Comm Tool icon or file in the Desktop folder
of the laptop, then the network settings of the laptop have caused the file to be saved in an
alternate location. Search the hard drive of the laptop for the file name WMS USB Test
Comm Tool to locate the file.
May 2010
Button Panel Maintenance 3-79
8 Start the WMS USB Test Comm Tool program and select Agree when prompted.
The Main Test Program window displays, Figure 3-132.
Figure 3-132 Main Test Program window.
16-022128-05
3-80 Chapter 3: Maintenance
9 Verify that the Product ID (hex) drop-down menu is set to 000b, Figure 3-133 (A), and select
Connect, Figure 3-133 (B).
Figure 3-133 Verify Product ID (hex) and select Connect.
A B
May 2010
Button Panel Maintenance 3-81
10 View the Status field in the Main Test Program window and determine the following:
If... Then...
the two windows shown at the program connected successfully with the Button Panel. Proceed to
Figure 3-134 display side by side, step 12 on page 3-71.
with "Connection index =3" shown
as the last entry on the left window
"No devices detected" displays the laptop is not communicating with the Button Panel and the USB or
Power Cable is likely disconnected or damaged. Complete the following
steps to find and address the error:
1 Check the connections of the 24V Power Cable and USB cable to the
Button Panel PCB.
2 Check the connection of the USB cable to the CPU.
3 Check the entire length of the USB cable for damage.
4 Check the connection of the 24V Power Cable at J22 on the Bulkhead
Board.
5 Check the entire length of the 24V Power Cable for damage.
6 Replace the USB cable.
7 Replace the 24V Power Cable.
8 Replace the Button Panel, as the Button Panel PCB may be damaged.
9 Try to connect to the Button Panel with another laptop.
Figure 3-134 Main Test Program window properly connected.
16-022128-05
3-82 Chapter 3: Maintenance
11 Select Firmware Download from the drop-down menu, even if that selection is already
highlighted, Figure 3-134 (A).
The Firmware Download window, Figure 3-135, displays.
Figure 3-135 Firmware Download Window.
12 Select Download Button Firmware (ALL buttons), Figure 3-135 (A).
NOTE: Confirm that this procedure is done correctly; otherwise only half of the OLED Graphics
will load.
May 2010
Button Panel Maintenance 3-83
13 When prompted, select the file OLEDBtn that was downloaded earlier to the laptop and saved
to an appropriate folder and select Open.
The status is displayed in the yellow banner as the existing Button Panel Controller Board
OLED Graphics are erased, Figure 3-136 (A), and the new OLED Graphics are installed. When
the installation is complete, the banner turns green, Figure 3-136 (B).
Figure 3-136 Firmware Download Window: EXAMPLE SHOWN.
A B C
14 Once the Button Panel Control Board is installed, select Download Controller Firmware,
Figure 3-136 (C).
16-022128-05
3-84 Chapter 3: Maintenance
15 When prompted, select the file btnpanelHT that was downloaded earlier to the laptop and
saved to an appropriate folder.
The status is displayed in the yellow banner as the existing Button OLED Graphics are erased,
Figure 3-137 (A), and the new OLED Graphics are installed.
Figure 3-137 Firmware Download Window.
A B
16 When the installation is complete, the banner turns green, Figure 3-137 (B), and the OLED
Graphics versions are displayed for the controller and each button position. Verify that the
version is correct for the controller and each button.
17 Close the WMS USB Test Comm Tool program.
18 Turn the game OFF at the Power Switch.
May 2010
Button Panel Maintenance 3-85
Reconnecting the Complete the following steps to reconnect the OLED Button Panel to the game:
OLED Button Panel 1 Connect the USB Cable, Figure 3-138 (A), to an available USB port on the CPU.
2 If applicable, install the USB Cover, Figure 3-138 (B).
If the Button Panel is being installed onto a game with an Ethernet/USB Cover,
Figure 3-138 (B), reference the Technical Service Bulletin 16-020293-xx: CPU-NXT Enclosure
Ethernet/USB Covers for the steps to access the USB Port.
Figure 3-138 USB Cable connected to CPU Enclosure (left) and version with USB Connector Cover
Plate (right).
A B
Figure 3-139 Connect the other end of the USB Cable to the OLED Button Panel.
3 Turn the game ON at the Power Switch.
Setting Device in Complete the following steps to set the Button Panel peripheral devices:
Administration 1 Turn the game ON at the Power Switch.
Menu
2 Press the Diagnostic switch. The Administration Menu displays.
3 Select Setup | Machine Setup| Device Setup.
The Device Config screen displays, Figure 3-140.
Figure 3-140 Device Config screen.
4 Select the inside of the Button Panel field and select USB OLED Button Panel.
5 When each device is correctly set, select Save.
The Administration Menu displays.
16-022128-05
