Protocol Conversion Gateway

GW-01 Setup Manual

Package Checklist Dimensions Installation Procedure Configuring IP and Network Settings
50mm

Step 1: Fasten the DIN rail clip to the Step 2: Clip the device onto the DIN rail Click [ ] to view the [iM-CONNECT] menu. Click [System Setup].
Gateway with two screws

25mm
USB recovery drive Click [Network Setup] to configure Gateway's IP Address and

2.5mm
Network Settings.

A. Ethernet
USB
Configure the IP address, Mask, Gateway, and DNS of [LAN1] and
Plug-able power terminal x1 [LAN2] respectively.
31.25mm 85.45mm

B. IP Address Ethernet
[Obtain IP address automatically(DHCP)]：System automatically
1

LAN2
obtains IP addresses.
[Use static IP address below] ：Manually input the IP
DIN-rail mounting kit x1:

LAN1
Addresses.
25mm DIN-rail clip x1

120mm
M3x6mm flat Head Screw x2 After configuration of each LAN, click [Submit] to save the settings

COM
to GW-01.

2
GW-01 x1

24VDC
Power Connection Product Specifications Accessing Your GW-01
The device requires a power voltage of DC 24V (+/-20%). For a power consumption of 6W on First time accessing the GW-01, connect your computer to the default ethernet port [LAN1]
the device, a power supply of 8W or above is recommended. Type Protocol Conversion Gateway Series of GW-01 with the default IP address http://192.168.0.80.
Model Number GW-01
Importance Notice CPU ARM Cortex-A8 (1GHz) Change your computer's IP setting to be in the same network with GW-01, e.g., the default IP
It is recommended that the power plug must be connected to the device power terminal SDRAM 512M Bytes address of GW-01 is 192.168.0.80; computer IP address set as 192.168.0.xxx. If not necessary,
prior to connecting to the power source. do not change the default IP address of LAN1.
Flash Memory 4GB, 8bit eMMC
Power-connecting steps FRAM (non-volatile) 32K Bytes
1. Remove the power plug from the power terminal of the device. RTC CR2032 Replaceable
2. Loosen the three screws on the power plug. COM 1 x RS232 1 x RS422/485
3. Strip the cable to expose the copper wire to about 7-8mm. Ethernet 2 x 10/100 Mbit
4. Insert the exposed copper wire into the three openings on the power plug. USB 1 x Type A (Host)
5. Retighten the three screws on the power plug.
Power Input 24V ± 20 % DC , Isolated Power
6. Plug the power plug back into the power terminal of the device.
Note Power Consumption 6W
The power plug is included and already plugged into the power terminal of the device. Operating Temperature -20 ~ 70°C
Storage Temperature -20 ~ 80°C Reset to Default
Power Line Type Power Line (AWG) Strip Length Torque Operation Humidity 10 ~ 90%RH non-condensing @40°C
If you forget the password or default configuration information, you can reset GW-01 to
Solid 28-12 About 7-8 mm About 4.5lb-in Dimension (mm) 120.00(W) x 85.45(H) x 31.25(D) mm
factory defaults. By plugging in the supplied USB recovery drive into the USB port on the
Stranded 30-12 About 7-8 mm About 4.5lb-in Net Weight 0.25 kg GW-01 for a few seconds, it will be restored to factory configuration and reboot.
DC FG Gross Weight 0.42 kg
+24 0V
* with copper conduction wire only. Note:
After GW-01 reboots, wait until the "beep" sound before opening or refreshing the webpage.
Grounding
COM Port
In order to maintain the operational condition and functioning of the hardware
components, please ensure proper power grounding. The assignment of each pin and COM port varies from that of a standard PC. Please refer to Service Port
Please ensure that the cable connecting the FG power terminal to the ground has a cable the above table for signal connection and pin assignment.
resistance lower than 100. 1. Open a browser and connect to When connecting GW-01 to external services, following port numbers will be required
Pin COM http://192.168.0.80 according to different services to permit the access.
COM Port Pin Assignment：
Warning 1 RS422 TX+ / RS485 TX/RX+
2 RS232 RX 2. Type the default username and
Server Default Port Client Default Port
Please read this manual before continuing with installation or operation of the device. password:
3 RS232 TX OPCUA Server 4840 MySQL 3306
Username: admin
4 RS422 RX+ Password: 1234 1833 (unencrypted) MSSQL 1433
General Guide 5 4 3 2 1 MQTT Broker
• Installation and operation of the device must be done by professionally trained staff. 5 SG 8883 (encrypted) OPEN VPN 1194
• Installation of the device must follow the instructions as printed in this manual. 9 8 7 6 6 RS422 TX- / RS485 TX/RX- FTP Server 21 LINE 443
• Installation of the device must be kept away from the risk of any liquid or metal particles 7 Optional TTL Level TXD Web Server 80 / 9000 Email 587
getting into the device. Foreign particles may cause internal components to short circuit 8 Optional TTL Level RXD
and thus damage the device or even catch fire. 9 RS422 RX-
• Installation of the device must be kept away from the risk of corrosion, explosion, or heavy 3. Click [Sign In] and the configuration page is displayed
electronic and magnetic elds. It must also be kept away from high humidity and extreme
shifts in temperature. Preparation Additional Information
Power Supply Setup Requirement To download the detailed user guide of GW-01 and understand the supported PLC models,
• The device is designed with an input power of DC 24V. If the supply voltage is outside of 1. GW-01 x1 pay a visit to Novakon official website：https://www.novakon.com.tw
the DC 24V +/- 20% range, it may result in damage or malfunction to the device. Therefore, 2. Computer with ethernet port x1
please confirm that the voltage is correct before powering the device on. Please also ensure 3. DC24V power supply x1
that the supplied power is stable during device operation.

Installation:
• Please avoid placing communication lines in the same conduit as the power lines and high
voltage lines. Isolated lines are suggested to reduce surrounding noise interference.

Service and Maintenance

• Please do not allow any non-trained staff members to perform the maintenance servicing.
• Please do not use batteries with poor quality.

Waste and Recycling

• Please adhere to local regulations when recycling device.
• The lithium battery, and capacitors contain hazardous material to individual health and
local environment, and must be disposed responsibly.
Your Intelligent IIoT Gateway Solutions
1306.0017 Rev:1.1