NTTF/H-3000
When installing more than one controller, the minimum horizontal and vertical distance between two holes should be
Intelligent Temperature Controller
NTTF/H-3000
25mm and 30mm respectively.
USER MANUAL （2）Insert the controller into the hole on the panel.
（3）Insert mounting bracket in the slot for mounting the controller.
Please read this manual thoroughly for the instruction of correct usage before using this product and keep this manual （4）Push the mounting bracket tightly to connect the instrument and the panel firmly.
as a reference. 2.3 Panel layout
①Display (Red)
l Before cleaning the controller, please ensure that the power is switch off. • Display the measuring temperature
l Please remove stains on the display panel by using a soft cloth only. ②Display (Green)
• Display the set time
l No scrubbing or touching the display panel with any hard object, the display panel can be easily scratched.
③Indicator
l Do not press any button on the display panel using pointy objects such as ballpoint pen or screw driver, it can • OUT indicator for heating output (Green), Bright at working.
easily scratch the panel or damage buttons on the panel. • SETTEM indicator (Red): Bright when setting the temperature
• AT/ALM indicator (Red), Bright at working.
• SETTIME indicator (GREEN): Bright when setting the time
④Function key
• Used to modify the setting value, calling out, modify and
Please confirm the product you received is in full agreement with the model that you selected according to the confirm the parameters。
following codes: ⑤ , ⑥Digital Adjustment Key
• Used to modify the setting value and the control parameters, or
for entering in the timing state.
① Panel size（mm） 4: Turn switch on to start timer and the relay will be closed. When the 2.4 Key Performance
H：48*96 E:72*72 timer reaches the preset value, the relay will be opened. 1) Measurement accuracy: 0.5%±1dig 2) Power: 220VAC 3)Operation Temperature:0～50℃ 4)Fuzzy PID control
5: Release switch to start timing, display will show remaining time,
② Model：3
when the timer research preset value, the relay will be closed. 5) This product conforms with the “Q/SQG01-1999 Intelligent Digital Display Adjustor” Standard Regulation.
③ Control Mode 6: Releasing switch to start timing, the relay will be closed, when the
0：On-Off Control time reaches the preset value, the relay will be opened.
4：On–Off PID Control (heating Type) ⑥ Output Type
④ Timing Output Omit: Relay Output
0: no timing output V: Logic Output (for the control of solid-state relay SSR) 3.1 Attention to the wiring
1: Relay Output G: SRC ((under 300W only)
2: Buzzer Output (internal) WG: external silicon controlled rectifier (1) For thermocouple input, the corresponding compensation line should be used.
3: Buzzer Output (external) WR: external relay (2) Input signal lines should be far away from power supply and load lines to avoid noise interference.
⑤ Timer Mode ⑦ Thermocouples types: 3.2 Wiring Terminal’s configuration
0: NO timing K：0-800℃；E：0-600℃；J:0-550℃
1: Timer Startup by a switch and display counting down ⑧ LRL
2: High and low temperature control, Timer Startup by a short current ⑨ URL
and display counting down
3: Timer Startup with set temperature and Counting down 2 9
OUT2
85~264
VAC
3 10
OUT1 +
+ 3 4 11
2.1 Caution when installing ~ TC
- 4 5 12
-
Please install the controller under the following conditions:
l Temperature: 0 to 50 degrees C. l Atmospheric pressure: 86 to 106kPa 6 13
l Humidity: 45% to 85% RH.
Please avoid the following conditions during installation: KT
l Rapid temperature changes, leading to dew condensation.
l Corrosive gases (especially sulfide gas, ammonia, etc.) or flammable gases.
l Direct vibration or shock
l Contact with water, oil, chemicals, steam , smoke, or hot water
l High concentrations of atmospheric dust, salt or iron particles 4.1 The order of calling out the various functions
l Large inductive interference, resulting in static electricity, magnetic fields or noise. After the instrument is power on, the upper row displays InP and the lower row displays the calibration mark of the
l Direct sunlight.
sensor to express the input type. 4 seconds later, the upper row displays the upper limit of the measuring range and the
l Radiant heat sources, etc
2.2 Mounting Process lower row displays the lower limit of the measuring range then the measurement range is determined. Again after 4
（1）Cut out rectangle holes on the panel for installing the controller according to the required hole size. seconds, the upper row displays the measuring value and the lower row displays the setting value. And then the system
enters its normal working state.
NTTF/H-3000
Setting of the temperature: Push the key X, the upper row displays the value of SP and push or key to make the
Offset of the Process -198… Using for correct the measurement error caused by the sensor and the
lower row display its needed value. And push the key to promote the system to the ST setting mode. 0
Pb Value 998℃ compensate line of the thermocouple
Setting of Timing: The upper row displays ST and push or key to make the lower row display the needed value.
0 or 10：when switch is on, display will start counting down to 0.
Again push the key to promote the system return to its standard mode. When the relay is closed, the alarm will be turned on until the
Setting of the control parameters: Push the key above 4 seconds, the upper row shows the prompt code of the switch is off and the relay is open. The alarm shall stop to complete
one cycle of operation.
parameter (detail can see the schedule table of the control parameters) and than push or key to make the lower row
1 or11：when switch is on, display will start counting down to 0 as
display its needed value. Continue push the key can make the upper row display the prompt code of each of another relay is closed. When relay is open, the alarm will be turned on
parameter in turn. Again push or Key to update the value of parameter to its needed value, and again push the X until the switch is off. The alarm shall stop to complete one cycle
of operation;
key above 4 seconds, the system returns back to its standard mode. (If no key has pushed down, after 1 minute the
2 or 12：High and low temperature control. Output will be set when
system will come to its standard mode). the temperature is below the preset value. Output will be reset
If under the red display the “ooo” is appeared, the thermocouple is in reverse connection, else above the red display when the preset value is reached. When the temperature of ON
switch is below than the high temperature preset value, output will
the “ooo” is appeared，the thermocouple is in open current or the measuring temperature exceeds the measurement
be set. When the high temperature preset value is reached, output
range. will be reset and the counting down will start.
The Auto-tuning function of the instrument’s parameters: After 20 seconds of pushing down the key, the AT 3 or 13：Switch on to start counting down. The relay is closed or
the alarm is on when remaining time is 0 until it has been switch
indicator is twinkle and the controller begins to start its Auto-tuning. The temperature goes through one to two times of
off and on again. Once switch is cycled, the relay will be opened
oscillation and the AT indicator extinguishes. The instrument will control the process with the updated parameters, Time control mode 0~16 0
and the alarm will be stopped to complete one cycle of operation.
which will be permanently persevered. 4 or 14：Switch on to start counting down and the relay will be
closed. When remaining time is 0, the relay will be opened or the
The switch function of Celsius and Fahrenheit temperature: Hold down the key or simultaneously, the upper
alarm will be turned on. Cycle and hold on switch to complete one
row shows LK, again push the X key to prompt the upper row appears Sn and lower row appears K-C (Celsius cycle of operation.
temperature) or K-F (Fahrenheit temperature) and push or key to carry out the transform of the scale of 5 or 15：Switch on and off to start counting down, when remaining
time is 0, the relay will be closed or the alarm will be turned on.
temperature.
The relay will open or the alarm is off until the next time release
Selection of the measurement range: Hold down the key or simultaneously, the upper row shows LK, again Run the switch to start to complete one cycle of operation.
push the X key to prompt the upper row appears rL and lower row appears 0, and again push X key to make the upper 6 or 16：Releasing switch to start counting down, the relay will be
closed or the alarm will be turned on. When remaining time is 0,
row appear rH, at that time the rower row appears the needed measurement range.
the relay is open and one cycle of operation is completed until the
4.2 The schedule table of the control parameter next release of the switch to start, the relay will be closed and the
Prompt Setting Beginning alarm will be stopped.
Name Illustration Others: not applicable;
Symbol Range Value
Note: when the digit segment of 10s is one, mute the device by
-199… Setting of Alarm 1，Insensitive interval of alarm is equal to a press any key.
Setting of Alarm 50 or 50.0
AL1 Range ℃ constant value 0.4 (This value is meaningless) 0：All parameters can be updated
coded lock 0，1，2 1：Only the Set Point Value can be updated 0
Proportional Control: The more the value of P, the less the LCK 2：All parameters cannot be updated.
Proportional band
0…400℃ proportional action and the less the system gain; only acting on the 30
P (Heating Side）
heating side. (P=0 is ON/OFF Control) Notice: Change of each function parameter in the table may alter the control effect of the system.
0…990 Integral Time: The more the value of I, the less the Integral action
Integral Time 240
I Seconds I=0 is PD Control，Ar=（Remained Error/P)×100
Differential Time
0…990 Differential time: The more the Value of D, the more the differential
60 This controller is under warranty for 12 months since the day of purchase (the warranty only stands if the problem is
D seconds action, which is able to overcome overshoot (D=0 is PI Control) caused by the malfunction due to manufacturing). Any repairment for damages caused by improper use of the controller
Used to restrain Overshoot (Ar is set to 1.5～2 times of the output empty will be charged. The controller is provided with lifetime maintenance and repair on cost.
Overshoot restrain
(Proportion re-setting)
ratio in the steady state of the system) Please keep the controller in a dry place with air and NO corrosive gas.
0～100% Reduce Ar energy and temperature overshoot, when SP is changing, 100
(Insensitive interval of
Ar Ar must be adjusted; Ar must be confirmed and will be set according
ON/OFF Control)
to SP value automatically.
When the relay output≮20s,SSR and Si-controlled switch
Control period 1…100
transwitch≮2s, continuous output T is equal to 1s, only acting on 20
T （Heating Side） Seconds
heating side
