Bulletin 74.

1
D101962X012 Type 1190
May 2024

Type 1190 Low-Pressure Tank

Blanketing Regulator

Figure 1. Type 1190 Tank Blanketing Regulator

Introduction Features
The Type 1190 low-pressure tank blanketing regulator is used for • Quick-Change Trim Package—Tested trim packages can be made
extremely accurate pressure control on very low-pressure blanketing up and stocked ahead of time for fast replacement.
systems. The regulator helps to control emissions and provides
protection against any contamination from atmospheric conditions by • In-Service Travel Inspection—Standard indicator assembly with
providing a flushing action. The Type 1190 tank blanketing regulator protective cover permits periodic inspection of plug travel without
maintains a positive vessel pressure thereby reducing the possibility removing regulators from service. It can also be used for remote
of vessel wall collapse during pump-out operations. alarming and monitoring stem position when combined with the
Topworx™ 4310 wireless position monitor. The Position Monitor
A Type 1190 low-pressure tank blanketing regulator reduces a Bracket (PMB) Mounting Kit is required; reference document
high-pressure gas, such as Nitrogen, to maintain a protective D103260X012 for more details.
environment above any liquid stored in a tank or vessel while
the liquid is being pumped out. Also, when the vessel cools • Easy In-Line Maintenance—Top-entry design reduces
suddenly causing the vapors inside the vessel to condense, the maintenance time and manpower requirements; trim parts can be
tank blanketing regulator replaces the condensed vapors with inspected, cleaned and replaced without removing the main valve
the blanketing gas to prevent the internal vessel pressure from body from the pipeline.
decreasing. In both cases, a slight positive vessel pressure prevents • Factory-Piped Pilot Supply—Supply pressure to pilot is supplied
outside air, moisture and other contaminants from entering the from inlet side of the main valve body through tubing furnished with
vessel and the possible collapse of the vessel walls. the regulator.
• Arctic Temperature Constructions—for process temperatures as
low as -76°F / -60°C.
• Hydrogen Ready—Products have been evaluated for material
compatibility, potential leakage and permeation and susceptibility
to embitterment for Hydrogen applications. Based on an extensive
evaluation and testing program, Type 1190 configurations are
available for use in Hydrogen applications.
Type 1190
Specifications
Specifications for a given regulator as it originally comes from the factory are stamped on nameplates located on the actuator and main valve
body, while the pilot outlet pressure range appears on the pilot spring case nameplate.

Body Sizes(1) Main Valve Temperature Capabilities(2)(3)

See Table 1 Nitrile (NBR): -20 to 180°F / -29 to 82°C
Fluorocarbon (FKM): 40 to 300°F / 4 to 149°C
Maximum Main Valve Inlet Pressures(2)
Ethylenepropylene (EPDM): -20 to 275°F / -29 to 135°C
400 psig / 27.6 bar
Perfluoroelastomer (FFKM): -20 to 300°F / -29 to 149°C
Maximum Operating Inlet Pressures(2)
Pilot Temperature Capabilities(3)
200 psig / 13.8 bar with Cast iron construction or 300 psig / 20.7
Nitrile (NBR): -20 to 180°F / -29 to 82°C
bar with a Steel or Stainless steel construction
Fluorocarbon (FKM): 40 to 180°F / 4 to 82°C
Maximum Outlet (Casing) Pressure(2)
Approximate Weights
Steel or Stainless steel: 75 psig / 5.2 bar
NPS 1 / DN 25: 85 lbs / 39 kg
Maximum Operating Outlet Pressure to Avoid Internal NPS 2 / DN 50: 100 lbs / 45 kg
Part Damage(2) NPS 3 / DN 80: 145 lbs / 66 kg
Nitrile (NBR) or Fluorocarbon (FKM) Diaphragm: NPS 4 / DN 100: 195 lbs / 88 kg
75 psig / 5.2 bar NPS 6 / DN 150: 380 lbs / 172 kg
NPS 8 x 6 / DN 200 x 150: 740 lbs / 336 kg
Outlet Pressure Ranges (Type T205P Pilot)(2) NPS 12 x 6 / DN 300 x 150: 1265 lbs / 574 kg
See Table2
Construction Materials (See Table 11 for Reference Information
Main Valve Orifice Diameters and Travels as to Material Compatibility)
See Table 3
Type EGR Main Valve
Proportional Bands Body and Body Flange: Cast iron and WCC steel (standard) or
See Table 4 CF8M Stainless steel (optional)
Seat Ring and Valve Plug: 416 Stainless steel (standard) or
Maximum and Minimum Differential Pressures 316 Stainless steel (optional)
See Table 5 Spring: Steel (standard) or Inconel® X750 (NACE)
O-rings and Seals: Nitrile (NBR) (standard),
Flow Coefficients for Relief Valve Sizing Fluorocarbon (FKM) and Perfluoroelastomer (FFKM) (optional)
See Table 8 Cage: Linear CF8M Stainless steel (standard), 416 Stainless
steel Whisper Trim™ Cage (optional) or 316 Stainless steel
Flow Coefficients for Fixed Restriction
Whisper Trim Cage (NACE)
Cg: 3; Cv: 11.7; C1: 35
Type 1098 Actuator
Supply Pressure Settings Required for the Type MR95H Supply Lower Diaphragm Case: Steel (standard) or Stainless steel
Pressure Regulator Upper Diaphragm Case: Steel (standard) or Stainless steel
See Table 9 Bonnet: Steel (standard) or Stainless steel (NACE)
Diaphragm and O-rings: Nitrile (NBR) (standard),
Flow Capacities Fluorocarbon (FKM) or EPDM (optional)
See Table 10
Type T205P Pilot
Pressure Registration Body: Carbon steel or Stainless steel
External Spring Case and Diaphragm Casing: Carbon steel or
Stainless steel
Main Valve Flow Characteristic Orifice: 303 Stainless steel (standard) or 316 Stainless
Linear steel (NACE)
Spring: Steel (standard)
Control Line Connection
Diaphragm: Nitrile (NBR) (standard) or Fluorocarbon (FKM)
3/4 NPT
O-rings, Gaskets and Seals: Nitrile (NBR) (standard),
Vent Connection on Pilot Spring Case Fluorocarbon (FKM), Perfluoroelastomer (FFKM) or
1/4 NPT EPDM (optional)
Disk: Nitrile (NBR) (standard), Fluorocarbon (FKM) or
EPDM (optional)
Disk Holder: 303 Stainless steel (standard) or 316 Stainless
steel (NACE)

1. End connections other than U.S. standard can usually be provided; consult your local Sales Office.
2. The pressure/temperature limits in this Bulletin and any applicable standard or code limitation should not be exceeded.
3. Special low temperature constructions for process temperatures between -76 to 180°F / -60 to 82°C are available by request. The low temperature construction passed Emerson
laboratory testing for lockup and external leakage down to -76°F / -60°C.

- continued -
Inconel is a mark owned by Special Metals Corporation.
®

2
 Type 1190
Specifications (continued)
Construction Materials (continued)
Type MR95H Supply Pressure Regulator
Body and Spring Case: Cast iron (standard), Steel, Stem Assembly: 416 Stainless steel (standard) or
Steel (NACE) and Stainless steel (optional) 316 Stainless steel (NACE)
Orifice: 416 Stainless steel (standard) or 316 Stainless Lower Spring Seat: Aluminum
steel (NACE) Upper Spring Seat: Steel
Valve Plug: 416 Stainless steel with Nitrile (NBR) (standard), Spring: Steel
416 Stainless steel with Fluorocarbon (FKM) or 316 Stainless Diaphragm: Neoprene (CR) (standard) or
steel with Neoprene (CR) (NACE) Fluorocarbon (FKM) (optional)

Table 1. Type EGR Main Valve Body Sizes and End Connection Styles
MAIN VALVE BODY SIZE MAIN VALVE END CONNECTION STYLE

NPS DN Cast Iron WCC Steel or CF8M Stainless Steel

1, 2 25, 50 NPT, CL125 FF or CL250 RF flanged NPT, SWE, BWE, CL150 RF, CL300 RF, CL600 RF or PN 16/25/40 flanged

3, 4, 6 80, 100, 150 CL125 FF or CL250 RF flanged BWE, CL150 RF, CL300 RF, CL600 RF or PN 16 flanged

8 x 6, 12 x 6 200 x 150, 300 x 150 ---- BWE, CL150 RF, CL300 RF, CL600 RF flanged or PN 25

Table 2. Outlet Pressure Ranges (Type T205P Pilot)

OUTLET PRESSURE RANGE(1) SPRING SPRING SPRING WIRE DIAMETER SPRING FREE LENGTH
In. w.c. mbar PART NUMBER COLOR In. mm In. mm
0.25 to 2.5(2) 0.6 to 6(2) 1B558527052 Orange 0.072 1.83 3.25 82.6
2 to 7(2) 5.0 to 17(2) 1B653827052 Red 0.085 2.16 3.63 92.1
5 to 16 12 to 40 1B653927022 Unpainted 0.105 2.67 3.75 95.3
0.5 to 1.2 psig 34 to 83 1B537027052 Yellow 0.114 2.90 4.31 109
1.1 to 2.5 psig 76 to 172 1B537127022 Green 0.156 3.96 4.06 103
2.5 to 4.5 psig 172 mbar to 0.31 bar 1B537227022 Light blue 0.187 4.75 3.94 100
4.5 to 7.0 psig 0.31 to 0.48 bar 1B537327052 Black 0.218 5.54 3.98 101
1. Outlet pressure ranges based on pilot being installed with the spring case pointed down.
2. Do not use Fluorocarbon (FKM) diaphragm with this spring at diaphragm temperatures lower than 60°F / 16°C.

Table 3. Type EGR Main Valve Orifice Diameters and Valve Plug Travels
TRAVEL

BODY SIZE ORIFICE DIAMETER Restricted Capacity

Standard
Travel
Percent
NPS DN In. mm In. mm In. mm

1 25 1-5/16 33 3/4 19 ---- ---- ----

30 3/8 9.5
2 50 2-3/8 60 1-1/8 29
70 5/8 16

3 80 3-3/8 86 1-1/2 38 40 7/8 22

4 100 4-3/8 111

2 51 40 1 25
6, 8 x 6, 12 x 6 150, 200 x 150, 300 x 150 7-3/16 183

Table 4. Proportional Bands - Type EGR Main Valve

PROPORTIONAL BAND

Green Main Valve Spring Blue Main Valve Spring Red Main Valve Spring
OUTLET PRESSURE RANGE
Maximum Inlet Pressure Maximum Inlet Pressure Range Maximum Inlet Pressure Range
60 psig / 4.1 bar 60 to 125 psig / 4.1 to 8.6 bar 125 to 300 psig / 8.6 to 20.7 bar

In. w.c. mbar In. w.c. mbar In. w.c. mbar In. w.c. mbar

0.25 to 2.5 0.6 to 6 0.25 0.6 0.5 1 1 2

2 to 7 5.0 to 17 0.25 0.6 0.5 1 1 2
5 to 16 12 to 40 0.25 0.6 0.5 1 1 2
0.5 to 1.2 psig 34 to 83 0.05 psig 3 0.10 psig 7 0.15 psig 10
1.1 to 2.5 psig 76 to 172 0.10 psig 7 0.15 psig 10 0.20 psig 14
2.5 to 4.5 psig 172 mbar to 0.31 bar 0.15 psig 10 0.20 psig 14 0.25 psig 17
4.5 to 7.0 psig 0.31 to 0.48 bar 0.20 psig 14 0.25 psig 17 0.30 psig 21

3
Type 1190

TYPE EGR
MAIN VALVE

TYPE MR95H SUPPLY

REGULATOR

CONTROL LINE
TYPE T205P PILOT

TYPE 1098
ACTUATOR

SETPOINT
ADJUSTMENT

FIXED
RESTRICTION

B2328_3

INLET PRESSURE DOWNSTREAM TANK BLANKETING

OUTLET PRESSURE BLEED LINE PRESSURE
LOADING PRESSURE
PILOT SUPPLY PRESSURE
ATMOSPHERIC PRESSURE

Figure 2. Operational Schematic

Principle of Operation
The Type 1190 tank blanketing regulator reduces a high-pressure pressure to operate the Type 1098-EGR main valve actuator. The
inert gas to maintain a positive low-pressure of blanket gas over outlet or vessel pressure is sensed through a control line on the
a stored liquid while liquid is being pumped out of the tank. Also, Type 1098-EGR main valve actuator and also on the Type T205P
when the tank suddenly cools causing tank vapors to condense, the pilot diaphragm.
Type 1190 regulator replaces the condensing vapors with an inert When the liquid level is decreased and vessel pressure decreases
gas to prevent the internal tank pressure from decreasing. In both below the pilot control spring setting, the pilot spring force on the
cases, a positive tank pressure prevents outside air from entering pilot diaphragm opens the pilot valve plug, allowing additional
the vessel preventing contamination and reducing the possibility of loading pressure to the main valve actuator diaphragm. The loading
atmospheric pressure collapsing the vessel. pressure opens the main valve plug to supply the required flow of
The Type 1190 regulator is pilot-operated. It responds to slight gas to the vessel.
decreases in internal tank pressure by throttling open to increase When downstream demand has been satisfied, outlet pressure
the flow rate of inert gas into the vessel. When the vessel’s liquid tends to increase slightly, acting on the pilot and main valve
level has been lowered to the desired point and the vapor pressure diaphragms. When the outlet pressure exceeds the pilot control
re-established, the Type 1190 regulator throttles closed. spring setting, the pilot diaphragm moves to close the pilot valve
The Type 1190 regulator utilizes a Type 1098-EGR main valve plug. The loading pressure reduces by exhausting downstream
actuator (Type EGR main valve and Type 1098 actuator), a through the fixed restriction, allowing the Type EGR main valve
Type T205P sensing pilot and a Type MR95H supply pressure spring to close the Type EGR main valve plug. The combination of
regulator. The Type T205P pilot uses the high-pressure inlet gas, Type EGR main valve spring force and Type EGR main valve plug
reduced by a Type MR95H supply pressure regulator, as loading unbalance provides positive shutoff of the valve plug.

4
 Type 1190
Table 5. Maximum and Minimum Differential Pressures for Type EGR Main Valve Spring Selection
TYPE EGR MINIMUM DIFFERENTIAL
MAXIMUM ALLOWABLE
BODY SIZE MAIN VALVE SPRING PRESSURE REQUIRED
DIFFERENTIAL PRESSURE
SPRING PART COLOR FOR FULL STROKE
NPS DN NUMBER psig bar psig bar

14A9687X012 Green 60 4.1 2.5 0.17

1 25 14A9680X012 Blue 125 8.6 4 0.28

300 or body rating limit, 20.7 or body rating limit,

14A9679X012 Red 5 0.34
whichever is lower whichever is lower

14A6626X012 Green 60 4.1 3 0.21

2 50 14A6627X012 Blue 125 8.6 5 0.34

300 or body rating limit, 20.7 or body rating limit,

14A6628X012 Red 10 0.69
whichever is lower whichever is lower

14A6629X012 Green 60 4.1 4 0.28

3 80 14A6630X012 Blue 125 8.6 6 0.41

300 or body rating limit, 20.7 or body rating limit,

14A6631X012 Red 11 0.76
whichever is lower whichever is lower

14A6632X012 Green 60 4.1 5 0.34

4 100 14A6633X012 Blue 125 8.6 8 0.55

300 or body rating limit, 20.7 or body rating limit,

14A6634X012 Red 13 0.90
whichever is lower whichever is lower

14A9686X012 Green 60 4.1 9.5 0.66

6, 150,
8 x 6, 200 x 150, 14A9685X012 Blue 125 8.6 14 1.0
12 x 6 300 x 150
300 or body rating limit, 20.7 or body rating limit,
15A2615X012 Red 19 1.3
whichever is lower whichever is lower

Table 6. Flow Rate Conversion (Gas Flow required to replace or displace Blanketing Gas with Pump-Out or Pump-In of Liquid)
MULTIPLY MAXIMUM PUMP RATE IN: BY TO OBTAIN(1):
U.S. GPM 8.021
U.S. GPH 0.1337
SCFH of air required
Barrels/hour 5.615
Barrels/day 0.2340
1. To obtain Nm3/h, multiply SCFH by 0.0268.

Table 7. G
 as Flow Required for Thermal Heating (Outbreathing) or Cooling (Inbreathing) per American Petroleum Institute
Standard 2000 (API 2000) (Interpolate for Intermediate sizes)
VESSEL CAPACITY AIR FLOW RATE REQUIRED
Barrel Gallon Liter SCFH Nm3/h
60 2500 9500 60 1.6
100 4200 16,000 100 2.7
500 21,000 79,500 500 13.4
1000 42,000 159,000 1000 26.8
2000 84,000 318,000 2000 53.6
3000 126,000 477,000 3000 80.4
4000 168,000 636,000 4000 107
5000 210,000 795,000 5000 134
10,000 420,000 1,590,000 10,000 268
15,000 630,000 2,385,000 15,000 402
20,000 840,000 3,180,000 20,000 536
25,000 1,050,000 3,975,000 24,000 643
30,000 1,260,000 4,769,000 28,000 750
35,000 1,470,000 5,564,000 31,000 831
40,000 1,680,000 6,359,000 34,000 911
45,000 1,890,000 7,154,000 37,000 992
50,000 2,100,000 7,949,000 40,000 1072
60,000 2,520,000 9,539,000 44,000 1179
70,000 2,940,000 11,129,000 48,000 1286
80,000 3,360,000 12,718,000 52,000 1394
90,000 3,780,000 14,308,000 56,000 1501
100,000 4,200,000 15,898,000 60,000 1608
120,000 5,040,000 19,078,000 68,000 1822
140,000 5,880,000 22,257,000 75,000 2010
160,000 6,720,000 25,437,000 82,000 2198
180,000 7,560,000 28,616,000 90,000 2412

5
Type 1190
Table 8. Flow Coefficients
PIPING STYLE
Line Size Equals Body Size Piping
BODY SIZE
Linear Cage Drilled Hole Whisper Trim™ Cage
Cg Cv Cg Cv
C1 C1
NPS DN Regulating Wide-Open Regulating Wide-Open Regulating Wide-Open Regulating Wide-Open
1 25 600 632 16.8 17.7 35.7 576 607 16.7 17.6 34.5
2 50 2280 2400 63.3 66.7 36.0 1970 2080 54.7 57.8 36.0
3 80 4630 4880 132 139 35.1 3760 3960 107 113 35.0
4 100 7320 7710 202 213 36.2 6280 6610 180 190 34.8
6 150 12,900 13,600 397 418 32.5 9450 9950 295 310 32.0
8x6 200 x 150 18,480 19,450 578 608 32.0 10,660 11,220 305 321 35.0
12 x 6 300 x 150 21,180 22,290 662 697 32.0 11,050 11,630 316 332 35.0
2:1 Line Size to Body Size Piping
BODY SIZE Standard Linear Cage Drilled Hole Whisper Trim Cage
Cg Cv Cg Cv
C1 C1
NPS DN Regulating Wide-Open Regulating Wide-Open Regulating Wide-Open Regulating Wide-Open
1 25 568 598 17.2 18.1 33.0 529 557 15.6 16.4 34.0
2 50 2050 2160 59.6 62.8 34.4 1830 1930 52.3 55.1 35.0
3 80 4410 4650 128 135 34.4 3630 3830 106 110 34.2
4 100 6940 7310 198 209 35.0 6020 6340 171 180 35.2
6 150 12,100 12,800 381 404 31.7 9240 9730 291 306 31.7
8x6 200 x 150 17,370 18,280 543 571 32.0 10,020 10,550 286 301 35.0
12 x 6 300 x 150 19,900 20,950 622 655 32.0 10,380 10,930 297 312 35.0

Table 9. Supply Pressure(1) Settings Required for the Type MR95H Regulator
SUPPLY PRESSURE
TYPE EGR Type T205P Spring Color and Outlet Pressure Range
BODY SIZE MAIN VALVE Orange Light Blue
SPRING Red Unpainted Yellow Green Black
0.25 to 2.5 to 4.5 psig /
PART NUMBER 2 to 7 in. w.c. / 5 to 16 in. w.c. / 0.5 to 1.2 psig / 1.1 to 2.5 psig / 4.5 to 7.0 psig /
2.5 in. w.c. / 172 mbar to
AND COLOR 5.0 to 17 mbar 12 to 40 mbar 34 to 83 mbar 76 to 172 mbar 0.31 to 0.48 bar
0.6 to 6 mbar 0.31 bar
NPS DN psig bar psig bar psig bar psig bar psig bar psig bar psig bar
14A9687X012, Green 6 0.41 6 0.41 6 0.41 7 0.48 8 0.55 11 0.76 13 0.90

1 25 14A9680X012, Blue 7 0.48 7 0.48 7 0.48 8 0.55 10 0.69 13 0.90 14 1.0

14A9679X012, Red 8 0.55 8 0.55 8 0.55 9 0.62 11 0.76 14 0.97 15 1.0

14A6626X012, Green 6 0.41 6 0.41 6 0.41 7 0.48 9 0.62 12 0.83 13 0.90

2 50 14A6627X012, Blue 8 0.55 8 0.55 8 0.55 9 0.62 11 0.76 14 0.97 15 1.0

14A6628X012, Red 13 0.90 13 0.90 13 0.90 14 1.0 16 1.1 19 1.3 20 1.4

14A6629X012, Green 7 0.48 7 0.48 7 0.48 8 0.55 10 0.69 13 0.90 14 1.0

3 80 14A6630X012, Blue 9 0.62 9 0.62 9 0.62 10 0.69 12 0.83 15 1.0 16 1.1

14A6631X012, Red 14 1.0 14 1.0 14 1.0 15 1.0 17 1.2 20 1.4 21 1.5

14A6632X012, Green 8 0.55 8 0.55 8 0.55 9 0.62 11 0.76 14 1.0 15 1.0

4 100 14A6633X012, Blue 11 0.76 11 0.76 11 0.76 12 0.83 14 1.0 17 1.2 18 1.3

14A6634X012, Red 16 1.1 16 1.1 16 1.1 17 1.2 19 1.3 22 1.5 23 1.6

150, 14A9686X012, Green 13 0.90 13 0.90 13 0.90 14 1.0 15 1.0 18 1.2 20 1.4
6, 200 x
8 x 6, 150, 14A9685X012, Blue 17 1.2 17 1.2 17 1.2 18 1.2 20 1.4 23 1.6 24 1.7
12 x 6 300 x
150 15A2615X012, Red 22 1.5 22 1.5 22 1.5 23 1.6 25 1.7 28 1.9 29 2.0

1. The pressures shown in the table are the minimum supply pressures required by the pilot. If the inlet pressure is less than shown, an external pilot supply is necessary.

Table 10. Flow Capacities in SCFH / Nm3/h of 0.97 Specific Gravity Nitrogen
CAPACITIES IN SCFH / Nm3/h OF 0.97 SPECIFIC GRAVITY NITROGEN
INLET PRESSURE OUTLET PRESSURE
NPS 1 / DN 25 Body NPS 2 / DN 50 Body NPS 3 / DN 80 Body NPS 4 / DN 100 Body NPS 6 / DN 150 Body
psig bar psig bar SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h
30 2.1 4 or less 0.28 or less 27,300 732 103,900 2785 204,000 5467 322,000 8630 580,000 15,544
40 2.8 33,300 892 126,600 3393 257,000 6888 406,300 10,889 716,100 19,191
50 3.5 39,400 1056 149,800 4015 304,000 8147 480,600 12,880 847,100 22,702
60 4.1 45,500 1219 173,000 4636 351,000 9407 554,900 14,871 978,000 26,210
7 or less 0.48 or less
70 4.8 51,600 1383 196,000 5253 398,000 10,666 629,200 16,863 1,108,900 29,719
80 5.5 57,700 1546 220,000 5896 444,900 11,923 703,500 18,854 1,239,900 33,229
90 6.2 64,000 1715 243,000 6512 491,900 13,183 777,800 20,845 1,370,800 36,737
100 6.9 70,100 1879 266,000 7129 538,900 14,443 852,100 22,836 1,501,700 40,246
120 8.3 82,300 2206 312,000 8362 632,900 16,962 1,000,600 26,816 1,763,600 47,264
140 9.7 94,500 2533 359,000 9621 726,900 19,481 1,149,200 30,799 2,025,400 54,281
7 or less 0.48 or less
160 11.0 107,000 2868 406,000 10,881 820,900 22,000 1,297,800 34,781 2,287,347 61,301
180 12.4 119,000 3189 452,000 12,114 914,800 24,517 1,446,400 38,764 2,549,200 68,319
200 13.8 131,000 3511 490,000 13,132 1,008,800 27,036 1,595,000 42,746 2,811,000 75,335

6
 Type 1190
Table 11. Materials Compatibility
CORROSION INFORMATION
Material Material

Stainless Steel

Stainless steel

Stainless steel

Stainless steel
Hastelloy® C(2)

Hastelloy® C(2)
416 Stainless

416 Stainless
Carbon steel

Carbon steel
CF8M or 316

CF8M or 316
Ductile Iron

Ductile Iron
302 or 304

302 or 304
Monel®(1)

Monel®(1)
Cast or

Cast or
Fluid Fluid

steel

steel
Acetic Acid (Air Free) C C B B C B A Hydrochloric Acid (Air Free) C C C C C C B
Acetic Acid Vapors C C A A C A A Hydrogen A A A A A A A
Acetone A A A A A A A Hydrogen Peroxide I.L. A A A B A B
Acetylene A A A A A A A Hydrogen Sulfide (Liquid) C C A A C C A
Alcohols A A A A A A A Magnesium Hydroxide A A A A A A A
Aluminum Sulfate C C A A C B A Methanol A A A A A A A
Ammonia A A A A A A A Methyl Ethyl Ketone A A A A A A A
Ammonium Chloride C C B B C B A Natural Gas A A A A A A A
Ammonium Nitrate A C A A C C A Nitric Acid C C A B C C B
Ammonium Sulfate C C B A C A A Petroleum Oils (Refined) A A A A A A A
Ammonium Sulfite C C A A B C A Phosphoric Acid (Air Free) C C A A C B A
Beer B B A A B A A Phosphoric Acid Vapors C C B A C C I.L.
Benzene (Benzol) A A A A A A A Potassium Chloride B B A A C B A
Benzoic Acid C C A A A A A Potassium Hydroxide B B A B B A A
Boric Acid C C A A B A A Propane A A A A A A A
Butane A A A A A A A Silver Nitrate C C A A B C A
Calcium Chloride (Alkaline) B B C B C A A Sodium Acetate A A B A A A A
Carbon Dioxide (Dry) A A A A A A A Sodium Carbonate A A A A B A A
Carbon Dioxide (Wet) C C A A A A A Sodium Chloride C C B B B A A
Carbon Disulfide A A A A B B A Sodium Chromate A A A A A A A
Carbon Tetrachloride B B B B C A A Sodium Hydroxide A A A A B A A
Carbonic Acid C C B B A A A Stearic Acid A C A A B B A
Chlorine Gas (Dry) A A B B C A A Sulfur A A A A A A A
Chlorine Gas (Wet) C C C C C C B Sulfur Dioxide (Dry) A A A A B A A
Chlorine (Liquid) C C C C C C A Sulfur Trioxide (Dry) A A A A B A A
Chromic Acid C C C B C A A Sulfuric Acid (Aerated) C C C C C C A
Citric Acid I.L. C B A B B A Sulfuric Acid (Air Free) C C C C C B A
Coke Oven Gas A A A A A B A Sulfurous Acid C C B B C C A
Copper Sulfate C C B B A C A Trichloroethylene B B B A B A A
Ether B B A A A A A Water (Boiler Feed) B C A A B A A
Ethyl Chloride C C A A B A A Water (Distilled) A A A A B A A
Ethylene A A A A A A A Water (Sea) B B B B C A A
Ethylene Glycol A A A A A A I.L. Zinc Chloride C C C C C C A
Formaldehyde B B A A A A A Zinc Sulfate C C A A B A A
Formic Acid I.L. C B B C A A ---- - - - - - - -
Freon (Wet) B B B A I.L. A A ---- - - - - - - -
Freon (Dry) B B A A I.L. A A ---- - - - - - - -
Gasoline (Refined) A A A A A A A ---- - - - - - - -
Glucose A A A A A A A ---- - - - - - - -
Hydrochloric Acid (Aerated) C C C C C C B ---- - - - - - - -
A+--Best possible selection C--Unsatisfactory
A--Recommended I.L.--Information lacking
B--Minor to moderate effect. Proceed with caution.

Capacity Information
Table 10 gives typical Nitrogen regulating capacities at selected inlet C1 = Cg/Cv or 35 as shown in Table 8
pressures and outlet pressure settings. Flows are in scfh (at 60°F Cg = gas sizing coefficient from Table 8
and 14.7 psia) and Nm3/h (at 0°C and 1.01325 bar) of 0.97 specific G = gas specific gravity (air = 1)
gravity Nitrogen. For gases of other specific gravities, multiply the P1abs = inlet pressure, psia (psig + 14.7 psi = psia)
given capacity of Nitrogen by 0.985, and divide by the square root of ∆P = pressure drop across the regulator, psi (P1 - P2)
the appropriate specific gravity of the gas required. Q = gas flow rate, SCFH
T = absolute gas temperature at inlet, °Rankine
To determine wide-open flow capacities for relief sizing, use the
P2 = outlet pressure, psig
following formula: where,

520 3417 ∆P
Q= CgP1absSIN DEG
GT C1 P1
Monel® is a mark owned by Special Metals Corporation.
Hastelloy® C is a mark owned by Haynes International, Inc.

7
Type 1190
Table 11. Materials Compatibility (continued)
FLUID INFORMATION
Material
Fluid Fluorocarbon Perfluorelastomer
Neoprene (CR) Nitrile (NBR) EPDM
(FKM) (FFKM)
Acetic Acid (30%) C B B A A
Acetone B C C A A
Alcohol (Ethyl) A A B A A
Alcohol (Methyl) A+ A C A A
Ammonia (Anhydrous) A C C A A
Ammonia (Gas, Hot) B C C A B
Benzene C C A A C
Brine (Calcium Chloride) A A B A A
Butadiene Gas B C B A C
Butane (Gas) A A+ A A C
Butane (Liquid) B A A A C
Carbon Tetrachloride C C A A C
Chlorine (Dry) C C A A C
Chlorine (Wet) C C A A C
Coke Oven Gas C B A+ A C
Ethyl Acetate C C C A B
Ethylene Glycol A A A A A
Freon 11 B A A+ A C
Freon 12 A+ A B A B
Freon 22 A+ C C A A
Freon 114 A A B A A
Gasoline B A+ A A C
Hydrogen Gas A A A A A
Hydrogen Sulfide (Dry) A C C A A
Hydrogen Sulfide (Wet) B C C A A
Jet Fuel (JP-4) C A A A I.L.
Natural Gas A A+ A A C
Natural Gas + H2S (Sour Gas) A B C A C
Nitric Acid (20%) B C A A C
Nitric Acid (50 to 100%) C C A A C
Nitrogen A A A A A
Oil (Fuel) B A+ A A C
Propane A A A A C
Sulfur Dioxide B A A A A
Sulfuric Acid (to 50%) A C A A A
Sulfuric Acid (50 to 100%) B C A A B
Water (Ambient) C C A A B
Water (at 200°F / 93°C) A A A A A
Water (Sea) C B B A A
A+--Best possible selection C--Unsatisfactory
A--Recommended I.L.--Information lacking
B--Minor to moderate effect. Proceed with caution.

Sizing Blanketing Systems Sample sizing problem:

When sizing a tank blanketing regulator for a low-pressure Vessel Capacity ..................................................... 50,000 barrels
blanketing application, you must consider the replacement of Pump In/Out Capacity .......................................... 100 GPM / 378 LPM
blanketing gas required for the liquid loss during pump out of the
vessel plus the condensation and contraction of the vessel vapors Inlet Pressure Source ............................ 60 psig / 4.1 bar of Nitrogen
during atmospheric thermal cooling. Desired Blanket Setpoint .................................. 0.5 in. w.c. / 1.2 mbar
Using procedures such as those established by the American 1. From Table 6 the desired air flow rate due to pump-out is 800
Petroleum Institute Standard 2000 (API 2000), determine the flow of SCFH / 21 Nm3/h of air (100 GPM / 378 LPM x 8.021 = 802).
blanketing gas required.
2. From Table 7 the desired air flow rate is 40,000 SCFH / 1072
1. Determine the gas flow rate required to replace the liquid being Nm3/h of air due to thermal cooling. Total required flow rate of
pumped out (see Table 6). 40,800 SCFH / 1093 Nm3/h of air converts to 41,600 SCFH /
2. Determine the gas flow rate due to “inbreathing” caused by 1115 Nm3/h of Nitrogen (40,800 x 1.018 = 41,534).
atmospheric thermal cooling (see Table 7). 3. From Table 10, an NPS 1 / DN 25 body size would flow
3. Add results from steps 1 and 2, then select regulator size, based 45,500 SCFH / 1219 Nm3/h of Nitrogen at 60 psig / 4.1 bar
on total capacity required (see Table 10). inlet pressure. This would satisfy the desired flow rate of
41,600 SCFH / 1115 Nm3/h of Nitrogen.

8
 Type 1190
A
16.06 /
408
A/2 CAP
Z REMOVAL
CLEARANCE

TYPE MR95H
SUPPLY REGULATOR

3/4 NPT
DOWNSTREAM
CONTROL CONNECTION

8.19 /
208

TYPE T205P
PILOT SIZE 40
ACTUATOR ACTUATOR
REMOVAL
A/R
B2416
CLEARANCE 13.12 /
333
IN. /
mm

TYPE 1190 WITH STANDARD CLOSING CAP ON TYPE T205P PILOT REGULATOR

Figure 3. Type 1190 Dimensional Drawing

Table 12. Dimensions

DIMENSIONS
A
CL125 FF CL250 FF
MAIN VALVE
Cast Iron or Cast Iron
BODY SIZE CL600 RF D G Z A/R
CL150 RF or CL300 RF
NPT Steel /
Steel Steel
Stainless Steel
or Stainless or Stainless
Steel Steel
NPS DN In. mm In. mm In. mm In. mm In. mm In. mm In. mm In. mm
1 25 8.25 210 7.25 184 7.75 197 8.25 210 3.88 98.6 8.62 219 11.38 289 3.00 76.2
2 50 11.25 286 10.00 254 10.50 267 11.25 286 4.56 116 9.12 232 12.62 321 3.12 79.2
3 80 ---- ---- 11.75 298 12.50 317 13.25 337 5.31 135 11.25 286 16.25 413 3.88 98.6
4 100 ---- ---- 13.88 353 14.50 368 15.50 394 6.50 165 12.62 321 18.88 480 5.12 130
6 150 ---- ---- 17.75 451 18.62 473 20.00 508 7.25 184 13.69 348 20.00 508 6.38 162

9
Type 1190
A
16.06 /
408
A/2 CAP
Z REMOVAL
CLEARANCE

TYPE MR95H

3/4 NPT
DOWNSTREAM
CONTROL CONNECTION

10.68 /
271.4

TYPE T205P
PILOT SIZE 40
ACTUATOR
ACTUATOR
13.12 /
REMOVAL
A/R 333
B2416 CLEARANCE

IN. /
mm

TYPE 1190 WITH EXTERNAL ADJUSTING SCREW ON TYPE T205P PILOT REGULATOR

Figure 3. Type 1190 Dimensional Drawing (continued)

Installation Ordering Information

Using a straight run of pipe the same size or larger than the Please complete the specifications worksheet at the bottom of the
regulator body, install the Type 1190 regulator as shown in Figure Ordering Guide on page 12. Refer to the Specifications section on
1 so that flow through the main valve body matches the flow arrow pages 2 and 3 and to Table 11 for material compatibility. Carefully
cast on the body. A downstream control line as shown in Figure 2 is review each specification, then complete the Ordering Guide on
required. If a block valve is required, install a full flow valve between pages 11 and 12. Right-side pilot mounting will be provided as
the regulator and the blanketed vessel. For proper operation at standard unless left-side mounting is specified.
low set point ranges, the regulator should be installed with the pilot
spring case barrel pointed down.
External dimensions and connections are shown in Figure 3.

10
 Type 1190
Ordering Guide Type T205P Pilot
Construction (Select One) Body Material (Select One)
 Standard  Carbon steel
 NACE  Stainless steel
Spring Case Material (Select One)
Type EGR Main Valve  Carbon steel
Main Valve Body Size (Select One)  Stainless steel
 NPS 1 / DN 25*** Diaphragm Casing Material
 NPS 2 / DN 50***  Carbon steel
 NPS 3 / DN 80***  Stainless steel
 NPS 4 / DN 100***
Outlet Pressure Range (Select One)
 NPS 6 / DN 150**
 0.25 to 2.5 in. w.c. / 0.6 to 6 mbar***
 NPS 8 x 6 / DN 200 x 150*
 2 to 7 in. w.c. / 5.0 to 17 mbar***
 NPS 12 x 6 / DN 300 x 150*
 5 to 16 in. w.c. / 12 to 40 mbar***
Main Valve Body Material (Select One)  0.5 to 1.2 psig / 34 to 83 mbar***
 Cast iron***  1.1 to 2.5 psig / 76 to 172 mbar
 WCC steel***  2.5 to 4.5 psig / 172 mbar to 0.31 bar***
 CF8M Stainless steel (NACE)***  4.5 to 7.0 psig / 0.31 to 0.48 bar***
Main Valve End Connection Style (Select One) Diaphragm Material (Select One)
Cast Iron Body  Nitrile (NBR)***
 NPT (Available for 1 or 2 NPT body sizes only)***  Fluorocarbon (FKM)**
 CL125 FF*** O-ring and Seal Material (Select One)
 CL250 RF***  Nitrile (NBR)***
WCC Steel or CF8M Stainless Steel Body  Fluorocarbon (FKM)**
 NPT (Available for 1 or 2 NPT body sizes only)***  EPDM**
 SWE*  Perfluoroelastomer (FFKM)*
 CL150 RF*** Closing Cap Material (Select One)
 CL300 RF***  Plastic***
 CL600 RF***  Steel**
 BWE 40**  Stainless steel**
 BWE 80*
NACE Required
 PN 16/25/40** __________ please specify rating
 Yes***
Main Valve Body Flange Material (Select One)
 Cast iron***
 WCC steel***
Type 1098 Actuator
 CF8M Stainless steel (NACE)** Lower Diaphragm Case Material (Select One)
 Steel***
Travel Stop (Select One)
 Stainless steel (NACE)**
 100 percent (standard)***
 60 percent** Bonnet Material (Select One)
 30 percent**  Steel***
 Stainless steel (NACE)**
Main Valve Cage Type and Material (Select One)
 Linear, CF8M Stainless steel (NACE)*** O-ring Material (Select One)
 Whisper Trim™ Cage, 416 Stainless steel***  Nitrile (NBR)***
 Whisper Trim Cage, 316 Stainless steel (NACE)***  Fluorocarbon (FKM)***
 EPDM**
Main Valve Spring Range (Select One)
 60 psig / 4.1 bar maximum drop, Green** Diaphragm Material (Select One)
 125 psig / 8.6 bar maximum drop, Blue***  Nitrile (NBR)***
 400 psig / 27.6 bar maximum drop, Red***  Fluorocarbon (FKM)***
 EPDM**
Main Valve Spring Material
 Steel*** Type MR95H Supply Pressure Regulator
 Inconel® X750 (NACE)*** Body Material (Select One)
O-ring and Seal Material (Select One)  Cast iron***
 Nitrile (NBR)***  Steel***
 Fluorocarbon (FKM)***  Stainless steel (NACE)***
 Perfluoroelastomer (FFKM)*** Spring Case Material (Select One)
 EPDM**  Cast iron***
 Steel***
 Stainless steel***

- continued -
Inconel is a mark owned by Special Metals Corporation.
®

11
Type 1190
Ordering Guide (continued)
Wireless Position Monitor Mounting Kit (Optional)
Type MR95H Supply Pressure  Yes, send one mounting kit for mounting the Topworx™ 4310
Regulator (continued) wireless position monitor.
Valve Plug Material (Select One)
 416 Stainless steel with Nitrile (NBR)***
 416 Stainless steel with Fluorocarbon (FKM)***
 316 Stainless steel with Neoprene (CR) (NACE)** Specification Worksheet
Outlet Pressure Range (Select One) Application Specifications:
 5 to 30 psig / 0.34 to 2.1 bar, Yellow***
Tank Size
Diaphragm Material (Select One) Pump In Rate
 Neoprene (CR)*** Pump Out Rate
 Fluorocarbon (FKM)*** Blanketing Gas (Type and Specific Gravity)
Parts Kit
Pressure Requirements (Please Designate Units):
Replacement Parts Kit (Optional) Maximum Inlet Pressure (P1max)
 Yes, send one replacement parts kit to match this order for each Minimum Inlet Pressure (P1min)
unit. Control Pressure Setting (P2)
Quick-Change Trim Package (Optional) Maximum Flow (Qmax)
 Yes, send one main valve Quick-Change Trim Package to
Accuracy Requirements:
match this order.
0.25 in. w.c. / 0.6 mbar 0.5 in. w.c. / 1 mbar
1 in. w.c. / 2 mbar 2 in. w.c. / 5 mbar
Others
Other Specifications:
Regulators Quick Order Guide
Is a vapor recovery regulator required? Yes No
*** Readily Available for Shipment Special Material Requirements: Ductile Iron Steel
** Allow Additional Time for Shipment Stainless Steel Other
Special Order, Constructed from Non-Stocked Parts. Other Requirements:
*
Consult your local Sales Office for Availability.
Availability of the product being ordered is determined by the component with the
longest shipping time for the requested construction.

[email protected] Facebook.com/EmersonAutomationSolutions
Fisher.com LinkedIn.com/company/emerson-automation-solutions
Twitter.com/emr_automation
D101962X012 © 1993, 2024 Emerson Process Management Regulator
Technologies, Inc. All rights reserved. 05/24.
Emerson The Emerson logo is a trademark and service mark of Emerson Electric
Co. All other marks are the property of their prospective owners.
Fisher™ is a mark owned by Fisher Controls International LLC, a business
Americas Asia Pacific of Emerson Automation Solutions.
McKinney, Texas 75070 USA Singapore 128461, Singapore The contents of this publication are presented for informational purposes
T +1 800 558 5853 T +65 6777 8211 only, and while every effort has been made to ensure their accuracy,
+1 972 548 3574 they are not to be construed as warranties or guarantees, express or
implied, regarding the products or services described herein or their use
Europe Middle East and Africa or applicability. All sales are governed by our terms and conditions, which
Bologna 40013, Italy Dubai, United Arab Emirates are available upon request. We reserve the right to modify or improve the
T +39 051 419 0611 T +971 4 811 8100 designs or specifications of such products at any time without notice.
Emerson Process Management Regulator Technologies, Inc. does
not assume responsibility for the selection, use or maintenance of any
product. Responsibility for proper selection, use and maintenance of any
Emerson Process Management Regulator Technologies, Inc. product
remains solely with the purchaser.