AMEROX® GAS WELDING
AND CUTTING KIT
DESCRIPTION
The AMEROX Gas Welding and Cutting Kit is especially
designed to meet the highest standards of the worldwide
marine industry and to perform under the most rigorous
shipboard conditions.
All parts in the AMEROX kit are fully interchangeable with
most existing equipment now onboard and are designed
and constructed to provide top performance and reliability.
Safety is always a prime consideration, from the nozzle
mixing design of our cutting attachment to the recommended
flashback arrestors and backfire valves, which no welder
should be without. One example is the chrome plating on
AMEROX blowpipes, which is specifically applied in order
to avoid spatter adherence and to reduce heat transfer and PCN 0523010
possible backfires.
KIT CONTENTS
Our products are designed to perform safely and reliably
under the toughest shipboard conditions. They are supported Description PCN
with parts and service through the Drew Marine organization Torch Handle - Complete with
0526014
in all major ports throughout the world. 3/8” sockets and nuts
Welding Blowpipe - 50 Liter/Hr 0527012
The AMEROX Gas Welding and Cutting Kit contains all
basic components required for manual gas welding, cutting Welding Blowpipe 100 Liter/Hr 0528010
and brazing onboard ship. The product code number for the Welding Blowpipe 225 Liter/Hr 0529018
complete kit is 523010. Kit components, listed here, may be
Welding Blowpipe 400 Liter/Hr 0530015
ordered as individual replacement parts using the product
code numbers indicated. Welding Blowpipe 650 Liter/Hr 0531013
Welding Blowpipe 1000 Liter/Hr 0660010
Please refer to pages 10 and 11 of the Drew Marine Welding
and Refrigeration Products catalog (#WRP-9) in order Welding Blowpipe 1300 Liter/Hr 0532011
to choose other system parts such as regulators, hoses, Welding Blowpipe 1650 Liter/Hr 0533019
backfire valves, flashback arrestors and safety and protective
equipment necessary to complete an installation. Cutting Attachment 90° 0535015
Cutting Roller Guide 0538019
NOTE: Drew Marine blowpipes, nozzles, cutting attachments
Cutting Circular Bar and Center 0537011
and torch handles may be fully interchangeable with
existing parts now onboard. These existing parts may be Cutting Nozzle 3-10MM 0536013
worn or otherwise unsafe and therefore should be replaced
Cutting Nozzle 10-30MM 0661018
with new Drew Marine equipment to avoid possible serious
damage or injury. Cutting Nozzle 30-60MM 0539017
Cutting Nozzle 60-100MM 0540014
Cleaning Needles 0541012
Spanner (not shown) 0665010
Spare Parts Kit 0545014
Carrying Case 0790015
Welding and Cutting Guide WRP-17
Safety and Operating Instruction
WRP-12
Booklet AMEROX Products
Contact your Drew Marine representative for more information
Continued on Page 2
Drew Marine maintains Safety Data Sheets on all of its
products. These documents contain health and safety
information for the development of appropriate product
handling procedures to protect your employees. Safety
Data Sheets should be read and understood by all of your
supervisory personnel and employees before using
Drew Marine products.
400 Captain Neville Drive
Waterbury, CT 06705 USA
1-973-526-5700
Drew-Marine.com
Copyright © Drew Marine. All Rights Reserved. All statements, information and data presented herein are believed to be accurate and reliable but are
not to be taken as a guarantee, express warranty or implied warranty of merchantability or fitness f or a p articular p urpose, o r r epresentation, express
or implied, for which seller assumes legal responsibility, and they are offered solely for your consideration, investigation and verification. Statements or
suggestions concerning possible use of this product are made without representation or warranty that any such use is free of patent infringement and are
not recommendations to infringe on any patent.
AMEROX® Gas Welding and Cutting Kit PDS 0715 R0
