Scribd
Upload
30 views2 pages

ASME Cheat Sheet

The document outlines the testing and certification requirements for Pipe 106 GR B, SA234 WPB fittings, and SA105 forged fittings, specifying the necessary test reports and results needed for compliance. Key requirements include material test reports, hydrostatic tests, chemical analyses, tensile properties, and additional testing as specified in the purchase order. Each section details the specific information that must be included in the test reports to ensure adherence to relevant standards.

Uploaded by

b.sachin
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
30 views2 pages

ASME Cheat Sheet

The document outlines the testing and certification requirements for Pipe 106 GR B, SA234 WPB fittings, and SA105 forged fittings, specifying the necessary test reports and results needed for compliance. Key requirements include material test reports, hydrostatic tests, chemical analyses, tensile properties, and additional testing as specified in the purchase order. Each section details the specific information that must be included in the test reports to ensure adherence to relevant standards.

Uploaded by

b.sachin
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
You are on page 1/ 2

Pipe 106 GR B

Material Test Report (MTR) Required as per SA530M Para 21 and shall be certified to EN 10204 Type 3.1.
Para 20 20. Hydrostatic Test Requirements
Para 21 21.2 In addition, the Certified Test Report shall include
the following information and test results, when applicable:
21.2.1 Heat Number,
21.2.2 Heat Analysis, Tension Test Gauge length 50mm
21.2.3 Product Analysis, if specfied or required,
21.2.4 Tensile Properties,
21.2.5 Width of the gage length, when longitudinal
strip tension test specimens are used,
21.2.6 Bend Test acceptable,
21.2.7 Flattening Test acceptable,
21.2.8 Hydrostatic Test pressure,
21.2.9 Non-destructive Electric Test method,
21.2.10 Impact Test results, and
21.2.11 Other test results or information required to
be reported by the product specification.

SA234 WPB Fittings


Para 18 18.1 Test reports are required for all fittings covered by this
specification. Each test report shall meet the requirements for
certification in A960/A960M as well as include the following
information specific to this specification:
18.1.1 Chemical analysis results, Section 8 (Table 1), reported
results shall be to the same number of significant figures
as the limits specified in Table 1 for that element.
18.1.2 Tensile property results, Section 9 (Table 2), report
the yield strength and tensile strength in ksi [MPa] and
elongation in percent,
18.1.3 Hardness results, Section 10,
18.1.4 Type heat treatment, if any, Section 7,
18.1.5 Seamless or welded,
18.1.6 Starting material, specifically pipe, plate, etc.,
18.1.7 Statement regarding radiographic or ultrasonic
examination, Section 6.3, and
18.1.8 Any supplementary testing required by the purchase
order.
Fitting made from plate CE = 0.35Max

SA105 Forged Fitting


12.2 Test Reports — When test reports are required,
the manufacturer shall also provide the following, where
applicable:
12.2.1 Type heat treatment, Section 5,
12.2.2 Tensile property results, Section 7 (Table 2),
report the yield strength and ultimate strength, in ksi [MPa],
elongation and reduction in area, in percent; and, if longitudinal
strip tension specimens are used, report the width of
the gage length,
12.2.3 Chemical analysis results, Section 6 (Table 1).
When the amount of an unspecified element is less than
0.02%, then the analysis for that element may be reported
as “< 0.02%,”
12.2.4 Hardness results, Section 7 (Table 2), and
12.2.5 Any supplementary testing required by the
purchase order.

You might also like