Integrated Membranes Solutions Design Software
Created on: 10/17/2022 01:49:13
Basic Design
Project name 2x500 m3/day BWRO Page : 1/3
Calculated by Khadidja Permeate flow/train 2500.0 m3/d
HP Pump flow 130.19 m3/h Raw water flow/train 3125.0 m3/d
Feed pressure 14.2 bar Permeate recovery 80.00 %
Feed temperature 25.0 °C(77.0°F) Element age 3.0 years
Feed water pH 7.00 Flux decline %, per year 5.0
Chem dose, mg/l, - None Fouling factor 0.86
Specific energy 0.61 kwh/m3 SP increase, per year 7.0 %
Pass NDP 9.8 bar Inter-stage pipe loss 0.207 bar
Average flux rate 25.9 lmh
Feed type Brackish Well Non-Fouling
Pass - Perm. Flow / Vessel Flux DP Flux Beta Stagewise Pressure Perm. Element Element PV# x
Stage Flow Feed Conc Max Perm. Boost Conc TDS Type Quantity Elem #
m3/h m3/h m3/h lmh bar lmh bar bar bar mg/l
1-1 77.3 11.8 4.8 31.6 1 36 1.18 0 0 13.3 21 CPA7-LD 66 11 x 6M
1-2 26.9 7.6 3.7 17.3 0.5 23.4 1.12 0 0 12.6 115.2 CPA7-LD 42 7 x 6M
Ion (mg/l) Raw Water Feed Water Permeate Water Concentrate 1 Concentrate 2
Hardness, as CaCO3 0.00 0.00 0.000 0.0 0.0
Ca 0.00 0.00 0.000 0.0 0.0
Mg 0.00 0.00 0.000 0.0 0.0
Na 905.03 905.03 17.847 2214.6 4465.8
K 0.00 0.00 0.000 0.0 0.0
NH4 0.00 0.00 0.000 0.0 0.0
Ba 0.000 0.000 0.000 0.0 0.0
Sr 0.000 0.000 0.000 0.0 0.0
H 0.00 0.00 0.002 0.0 0.0
CO3 0.00 0.00 0.000 0.0 0.0
HCO3 0.10 0.10 0.004 0.2 0.5
SO4 0.00 0.00 0.000 0.0 0.0
Cl 1394.87 1394.87 27.506 3413.3 6882.8
F 0.00 0.00 0.000 0.0 0.0
NO3 0.00 0.00 0.000 0.0 0.0
PO4 0.00 0.00 0.000 0.0 0.0
OH 0.00 0.00 0.000 0.0 0.0
SiO2 0.00 0.00 0.000 0.0 0.0
B 0.00 0.00 0.000 0.0 0.0
CO2 0.01 0.01 0.01 0.01 0.01
NH3 0.00 0.00 0.00 0.00 0.00
TDS 2300.00 2300.00 45.36 5628.11 11349.08
pH 7.00 7.00 5.69 7.35 7.62
Saturations Raw Water Feed Water Concentrate Limits
CaSO4 / ksp * 100, % 0 0 0 400
SrSO4 / ksp * 100, % 0 0 0 1200
BaSO4 / ksp * 100, % 0 0 0 10000
SiO2 saturation, % 0 0 0 140
CaF2 / ksp * 100, % 0 0 0 50000
Ca3(PO4)2 saturation index 0.0 0.0 0.0 2.4
CCPP, mg/l 0.00 0.00 0.00 850
Langelier saturation index 0.00 0.00 0.00 2.8
Ionic strength 0.04 0.04 0.19
Osmotic pressure, bar 1.8 1.8 9.0
Product performance calculations are based on nominal element performance when operated on a feed water of acceptable quality. The results shown on the printouts produced by this program are
estimates of product performance. No guarantee of product or system performance is expressed or implied unless provided in a separate warranty statement signed by an authorized Hydranautics
representative. Calculations for chemical consumption are provided for convenience and are based on various assumptions concerning water quality and composition. As the actual amount of chemical
needed for pH adjustment is feedwater dependent and not membrane dependent, Hydranautics does not warrant chemical consumption. If a product or system warranty is required, please contact your
Hydranautics representative. Non-standard or extended warranties may result in different pricing than previously quoted. Version : 2.231.90 %
Email : [email protected]
Integrated Membranes Solutions Design Software
Created on: 10/17/2022 01:49:13
Basic Design
Project name 2x500 m3/day BWRO Page : 2/3
Calculated by Khadidja Permeate flow/train 2500.0 m3/d
HP Pump flow 130.19 m3/h Raw water flow/train 3125.0 m3/d
Feed pressure 14.2 bar Permeate recovery 80.00 %
Feed temperature 25.0 °C(77.0°F) Element age 3.0 years
Feed water pH 7.00 Flux decline %, per year 5.0
Chem dose, mg/l, - None Fouling factor 0.86
Specific energy 0.61 kwh/m3 SP increase, per year 7.0 %
Pass NDP 9.8 bar Inter-stage pipe loss 0.207 bar
Average flux rate 25.9 lmh
Feed type Brackish Well Non-Fouling
Pass - Perm. Flow / Vessel Flux DP Flux Beta Stagewise Pressure Perm. Element Element PV# x
Stage Flow Feed Conc Max Perm. Boost Conc TDS Type Quantity Elem #
m3/h m3/h m3/h lmh bar lmh bar bar bar mg/l
1-1 77.3 11.8 4.8 31.6 1 36 1.18 0 0 13.3 21 CPA7-LD 66 11 x 6M
1-2 26.9 7.6 3.7 17.3 0.5 23.4 1.12 0 0 12.6 115.2 CPA7-LD 42 7 x 6M
Permeat Permeate
Pass - Element Feed Pressure Conc NDP e Water Water Beta Permeate (Stagewise cumulative)
Stage no. Pressure Drop Osmo. Flow Flux TDS Ca Mg Na Cl
bar bar bar bar m3/h lmh
1-1 1 14.2 0.25 2.1 12.2 1.3 36 1.11 10 0 0 3.92 6.042
1-1 2 14 0.21 2.3 11.7 1.3 34.3 1.12 11.2 0 0 4.418 6.809
1-1 3 13.8 0.17 2.7 11.2 1.2 32.6 1.13 12.8 0 0 5.032 7.756
1-1 4 13.6 0.14 3.1 10.6 1.1 30.9 1.15 14.8 0 0 5.816 8.964
1-1 5 13.5 0.11 3.7 10 1.1 28.9 1.16 17.4 0 0 6.848 10.555
1-1 6 13.4 0.09 4.5 9.3 1 26.5 1.18 21 0 0 8.252 12.717
1-2 1 13.1 0.13 5 8.3 0.9 23.4 1.12 61.6 0 0 24.248 37.37
1-2 2 12.9 0.11 5.7 7.5 0.8 21.2 1.12 68.9 0 0 27.11 41.78
1-2 3 12.8 0.09 6.4 6.7 0.7 18.7 1.1 77.6 0 0 30.546 47.077
1-2 4 12.7 0.07 7.3 5.9 0.6 16.1 1.12 88.1 0 0 34.666 53.425
1-2 5 12.7 0.06 8.1 5 0.5 13.4 1.11 100.5 0 0 39.562 60.971
1-2 6 12.6 0.05 9 4.1 0.4 10.9 1.1 115.2 0 0 45.317 69.841
Product performance calculations are based on nominal element performance when operated on a feed water of acceptable quality. The results shown on the printouts produced by this program are
estimates of product performance. No guarantee of product or system performance is expressed or implied unless provided in a separate warranty statement signed by an authorized Hydranautics
representative. Calculations for chemical consumption are provided for convenience and are based on various assumptions concerning water quality and composition. As the actual amount of chemical
needed for pH adjustment is feedwater dependent and not membrane dependent, Hydranautics does not warrant chemical consumption. If a product or system warranty is required, please contact your
Hydranautics representative. Non-standard or extended warranties may result in different pricing than previously quoted. Version : 2.231.90 %
Email : [email protected]
Integrated Membranes Solutions Design Software
Created on: 10/17/2022 01:49:13
Basic Design
Project name 2x500 m3/day BWRO Page : 3/3
Temperature : 25.0 °C Element age, P1 : 3.0 years
Stream No. Flow (m3/h) Pressure (bar) TDS (mg/l) pH Econd (µs/cm)
1 130 0 2300 7.00 4318
2 130 14.2 2300 7.00 4318
3 52.9 13.3 5628 7.35 9754
4 26.0 12.6 11349 7.62 18656
5 77.3 0 21.0 5.36 46.9
6 26.9 0 115 6.08 249
7 104 0 45.4 5.69 98.8
Product performance calculations are based on nominal element performance when operated on a feed water of acceptable quality. The results shown on the printouts produced by this program are
estimates of product performance. No guarantee of product or system performance is expressed or implied unless provided in a separate warranty statement signed by an authorized Hydranautics
representative. Calculations for chemical consumption are provided for convenience and are based on various assumptions concerning water quality and composition. As the actual amount of chemical
needed for pH adjustment is feedwater dependent and not membrane dependent, Hydranautics does not warrant chemical consumption. If a product or system warranty is required, please contact your
Hydranautics representative. Non-standard or extended warranties may result in different pricing than previously quoted. Version : 2.231.90 %
Email : [email protected]
