10G-SFPP-BXD-AO
Brocade® (Formerly) 10G-SFPP-BXD Compatible TAA Compliant 10GBase-BX SFP+ Transceiver (SMF,
1330nmTx/1270nmRx, 10km, LC, DOM)
Features
• SFF-8432 and SFF-8472 Compliance
• Uncooled DFB transmitter and PIN receiver
• Simplex LC Connector
• Commercial Temperature 0 to 70 Celsius
• Single-mode Fiber
• Hot Pluggable
• Excellent ESD Protection
• Metal with Lower EMI
• RoHS Compliant and Lead Free
Applications
• 8x/10x Fibre Channel
• 10GBase-BX Ethernet
• Access, Metro and Enterprise
Product Description
This Brocade® (Formerly) 10G-SFPP-BXD compatible SFP+ transceiver provides 10GBase-BX throughput up to
10km over single-mode fiber (SMF) using a wavelength of 1330nmTx/1270nmRx via an LC connector. It is
guaranteed to be 100% compatible with the equivalent Brocade® (Formerly) transceiver. This easy to install,
hot swappable transceiver has been programmed, uniquely serialized and data-traffic and application tested to
ensure that it will initialize and perform identically. Digital optical monitoring (DOM) support is also present to
allow access to real-time operating parameters. This transceiver is Trade Agreements Act (TAA) compliant. We
stand behind the quality of our products and proudly offer a limited lifetime warranty.
AddOn’s transceivers are RoHS compliant and lead-free.
TAA refers to the Trade Agreements Act (19 U.S.C. & 2501-2581), which is intended to
foster fair and open international trade. TAA requires that the U.S. Government may
acquire only “U.S. – made or designated country end products.”
Rev. 033023
Regulatory Compliance
• ESD to the Electrical PINs: compatible with MIL-STD-883E Method 3015.4.
• ESD to the LC Receptacle: compatible with IEC 61000-4-3.
• EMI/EMC: compatible with FCC Part 15 Subpart B Rules, EN55022:2010.
• Laser Eye Safety: compatible with FDA 21CFR, EN60950-1& EN (IEC) 60825-1, 2.
• RoHS: compliant with EU RoHS 2.0 directive 2015/863/EU.
Absolute Maximum Ratings
Parameter Symbol Min. Typ. Max. Unit Notes
Maximum Supply Voltage Vcc -0.5 4.0 V 1
Storage Temperature Tstg -40 85 °C 2
Operating Case Temperature Tc 0 70 °C 3
Data Rate DR 9.83 11.3 Gbps 4
Bit Error Rate BER 10-12
Supply Current Icc 200 350 mA 1
Notes:
1. For electrical power interface.
2. Ambient temperature.
3. Case Temperature.
4. IEEE 802.3ae.
Electrical Characteristics
Parameter Symbol Min. Typ. Max. Unit Notes
Power Supply Voltage Vcc 3.14 3.3 3.46 V
Power Dissipation PDISS 0.65 1.2 W
Transmitter
Input Differential Impedance RIN 100 Ω
Differential Data Input Swing VIN,pp 180 700 mV
Transmit Disable Voltage VD 2.0 Vcc V
Transmit Enable Voltage VEN Vee Vee+0.8 V
Receiver
Differential Data Output Swing VOUT,pp 300 850 mV
Data Output Rise Time/Fall Time (20-80%) Tr/Tf 28 ps
LOS Assert LOSA 2 Host_Vcc V
LOS De-Assert LOSD Vee Vee+0.5 V
Optical Characteristics
Parameter Symbol Min. Typ. Max. Unit Notes
Transmitter
Output Optical Power Ptx -8.2 0.5 dBm 1
Optical Center Wavelength λC 1320 1330 1340 nm
Extinction Ratio ER 3.5 dB
Spectral Width (-20dB) Δλ 0.6 nm
Side-Mode Suppression Ratio SMSR 30 dB
Relative Intensity Noise RIN -128 dB/Hz
Transmitter Dispersion Penalty TDP 3.2 dB
Launch Power of Off Transmitter Poff -30 dBm 1
Transmitter Jitter According to IEEE 802.3ae Requirement
Receiver
Receiver Overload 0.5 dBm
Optical Center Wavelength λC 1260 1270 1280 nm
Receiver Sensitivity S -14.4 dBm 2
Receiver Reflectance TRrx -12 dB
LOS Assert LOSA -30 dBm
LOS De-Assert LOSD -17 dBm
LOS Hysteresis LOSH 0.5 dB
Notes:
1. Average.
2. Average. Measured with worst ER: BER< 10-12 and 231-1 PRBS.
Pin Descriptions
Pin Symbol Name/Descriptions Notes
1 VeeT Transmitter Ground. Common with receiver ground. 1
2 Tx_Fault Transmitter Fault. 2
3 Tx_Disable Transmitter Disable. Laser output disabled on "high" or "open." 3
4 SDA 2-Wire Serial Interface Data. 4
5 SCL 2-Wire Serial Interface Clock. 4
6 MOD_ABS Module Absent. Grounded within the module. 4
7 RS0 No connection required.
8 LOS Loss of Signal indication. "Logic 0" indicates normal operation. 5
9 RS1 No connection required. 1
10 VeeR Receiver Ground. Common with transmitter ground. 1
11 VeeR Receiver Ground. Common with transmitter ground. 1
12 RD- Receiver Inverted Data Out. AC coupled.
13 RD+ Receiver Non-Inverted Data Out. AC coupled.
14 VeeR Receiver Ground. Common with transmitter ground. 1
15 VccR Receiver Power Supply.
16 VccT Transmitter Power Supply.
17 VeeT Transmitter Ground. Common with receiver ground. 1
18 TD+ Transmitter Non-Inverted Data In. AC coupled.
19 TD- Transmitter Inverted Data In. AC coupled.
20 VeeT Transmitter Ground. Common with receiver ground. 1
Notes:
1. Circuit ground is isolated from the chassis ground.
2. Tx_Fault is the open collector output and should be pulled up with 4.7kΩ-10kΩ on the host board to a
voltage between 2V and Vcc+0.3V.
3. Disabled: TDIS>2V or open. Enabled TDIS<0.8V.
4. Should be pulled up with the 4.7kΩ-10kΩ on the host board to a voltage between 2V and Vcc+0.3V.
5. LOS is open collector output and should be pulled with 4.7kΩ-10kΩ on the host board to a voltage
between 2V and Vcc+0.3V. The logic “0” indicated normal operation, and the logic “1” indicates that the
receiver signal is lost.
Transceiver Block Diagram
Electical Pad Layout
Mechanical Specifications
About AddOn Networks
In 1999, AddOn Networks entered the market with a single product. Our founders fulfilled a severe shortage
for compatible, cost-effective optical transceivers that compete at the same performance levels as leading
OEM manufacturers. Adhering to the idea of redefining service and product quality not previously had in the
fiber optic networking industry, AddOn invested resources in solution design, production, fulfillment, and
global support.
Combining one of the most extensive and stringent testing processes in the industry, an exceptional free
tech support center, and a consistent roll-out of innovative technologies, AddOn has continually set industry
standards of quality and reliability throughout its history.
Reliability is the cornerstone of any optical fiber network and is in engrained in AddOn's DNA. It has played a
key role in nurturing the long-term relationships developed over the years with customers. AddOn remains
committed to exceeding industry standards with certifications from ranging from NEBS Level 3 to ISO
9001:2005 with every new development while maintaining the signature reliability of its products.
U.S. Headquarters
Email: [email protected]
Telephone: +1 877.292.1701
Fax: 949.266.9273
Europe Headquarters
Email: [email protected]
Telephone: +44 1285 842070
