TS79M00 series

3-Terminal Medium Current Negative Voltage Regulator

Pin assignment:
1. Ground Voltage Range - 5V to - 24V
2. Input Output Current up to 0.5A
3. Output
(Heatsink surface
connected to Pin 2)

General Description
The TS79M00 Series negative voltage regulators are identical to the popular TS7900 Series devices, except that they are
specified for only half the output current. Like the TS7900 devices, the TS79M00 Series 3-Terminal regulators are
intended for local, on-card voltage regulation.
Internal current limiting, thermal shutdown circuitry and safe-area compensation for the internal pass transistor combine
to make these devices remarkably rugged under most operating conditions. Maximum output current with adequate
heatsink is 500mA
This series is offered in 3-pin TO-220, TO-252 package.

Features Standard Application

— Output current up to 0.5A
— No external components required
— Internal thermal overload protection
— Internal short-circuit current limiting
— Output transistor safe-area compensation
— Output voltage offered in 4% tolerance

Ordering Information A common ground is required between the input and the
output voltages. The input voltage must remain typically 2.0V
Part No. Operating Temp. Package above the output voltage even during the low point on the
o Input ripple voltage.
TS79MxxCZ -20 ~ +125 C TO-220
XX = these two digits of the type number indicate voltage.
TS79MxxCP TO-252
* = Cin is required if regulator is located an appreciable
Note: Where xx denotes voltage option. distance from power supply filter.
** = Co is not needed for stability; however, it does improve
transient response.
Absolute Maximum Rating
Input Voltage Vin * - 35 V
Input Voltage Vin ** - 40 V
Power Dissipation TO-220 Without heatsink 2
TO-220 Pt *** 15 W
TO-252 Without heatsink 1
o
Operating Junction Temperature Range TJ -20 ~ +125 C
o
Storage Temperature Range TSTG -65 ~ +150 C
Note : * TS79M05 to TS79M18
** TS79M24
*** Follow the derating curve

TS79M00 series 1-7 2003/12 rev. A

 TS79M05 Electrical Characteristics
o o
(Vin= -10V, Iout=350mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
Parameter Symbol Test Conditions Min Typ Max Unit
o
Tj=25 C - 4.80 -5 - 5.20
Output voltage Vout -7.5V≤Vin≤ -20V, - 4.75 -5 - 5.25 V
5mA≤Iout≤350mA, PD≤5W
-7.5V≤Vin≤ -25V, -- 3 50
Line Regulation REGline Tj=25 oC
Io=200mA mV

o 5mA≤Iout≤500mA -- 20 100
Load Regulation REGload Tj=25 C
5mA≤Iout≤200mA -- 10 50
o
Quiescent Current Iq Iout=0, Tj=25 C -- 4 8
-7.5V≤Vin≤ -25V -- -- 0.5 mA
Quiescent Current Change ∆Iq
5mA≤Iout≤350mA -- -- 0.5
o
Output Noise Voltage Vn 10Hz≤f≤100KHz, Tj=25 C -- 40 -- uV
Ripple Rejection Ratio RR f=120Hz, -8V≤Vin≤ -18V 54 66 -- dB
Voltage Drop Vdrop Iout=350mA, Tj=25 oC -- 2 -- V
o
Peak Output Current Io peak Tj=25 C -- 0.7 -- A
Temperature Coefficient of o o mV/
∆Vout/ ∆Tj Iout=5mA, 0 C≤Tj≤125 C -- -0.2 -- o
Output Voltage C

TS79M06 Electrical Characteristics

o o
(Vin= -11V, Iout=350mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
Parameter Symbol Test Conditions Min Typ Max Unit
o
Tj=25 C - 5.75 -6 - 6.25
Output Voltage Vout -8.5V≤Vin≤ -21V, - 6.3 -6 - 6.3 V
5mA≤Iout≤350mA, PD≤5W

o -8.5V≤Vin≤ -25V, -- 3 50
Line Regulation REGline Tj=25 C
Io=200mA mV
5mA≤Iout≤500A -- 20 120
Load Regulation REGload Tj=25 oC
5mA≤Iout≤200mA -- 10 60
Quiescent Current Iq Iout=0, Tj=25 oC -- 4 8
-8.5V≤Vin≤ -25V -- -- 0.5 mA
Quiescent Current Change ∆Iq
5mA≤Iout≤350mA -- -- 0.5
o
Output Noise Voltage Vn 10Hz≤f≤100KHz, Tj=25 C -- 40 -- uV
Ripple Rejection Ratio RR f=120Hz, -9V≤Vin≤ -19V 54 66 -- dB
o
Voltage Drop Vdrop Iout=350mA, Tj=25 C -- 2 -- V
o
Peak Output Current Io peak Tj=25 C -- 0.7 -- A
Temperature Coefficient of o o mV/
∆Vout/ ∆Tj Iout=5mA, 0 C≤Tj≤125 C -- -0.2 -- o
Output Voltage C
z Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as
possible, and thermal effects must be taken into account separately.
z This specification applies only for DC power dissipation permitted by absolute maximum ratings.

TS79M00 series 2-7 2003/12 rev. A

 TS79M08 Electrical Characteristics
o o
(Vin= -14V, Iout=350mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)

Parameter Symbol Test Conditions Min Typ Max Unit

o
Tj=25 C - 7.69 -8 - 8.32
Output Voltage Vout -10.5V≤Vin≤ -23V, - 7.61 -8 - 8.40 V
5mA≤Iout≤350mA, PD≤5W
-10.5V≤Vin≤ -25V, -- 6 50
Line Regulation REGline Tj=25 oC
Io=200mA mV

o 5mA≤Iout≤500mA -- 25 160
Load Regulation REGload Tj=25 C
5mA≤Iout≤200mA -- 10 80
o
Quiescent Current Iq Iout=0, Tj=25 C -- 4 8
-10.5V≤Vin≤ -25V -- -- 0.5 mA
Quiescent Current Change ∆Iq
5mA≤Iout≤350mA -- -- 0.5
o
Output Noise Voltage Vn 10Hz≤f≤100KHz, Tj=25 C -- 60 -- uV
Ripple Rejection Ratio RR f=120Hz, -11V≤Vin≤ -21V 54 63 -- dB
Voltage Drop Vdrop Iout=350mA, Tj=25 oC -- 2 -- V
o
Peak Output Current Io peak Tj=25 C -- 0.7 -- A
Temperature Coefficient of o o mV/
∆Vout/ ∆Tj Iout=5mA, 0 C≤Tj≤125 C -- -0.4 -- o
Output Voltage C

TS79M09 Electrical Characteristics

o o
(Vin= -15V, Iout=350mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)

Parameter Symbol Test Conditions Min Typ Max Unit

o
Tj=25 C - 8.65 -9 - 9.36
Output Voltage Vout -11.5V≤Vin≤ -23V, - 8.57 -9 - 9.45 V
5mA≤Iout≤350mA, PD≤5W

o -11.5V≤Vin≤ -26V -- 6 50
Line Regulation REGline Tj=25 C
Io=200mA mV
5mA≤Iout≤500mA -- 25 180
Load Regulation REGload Tj=25 oC
5mA≤Iout≤200mA -- 10 90
Quiescent Current Iq Iout=0, Tj=25 oC -- 4 8
-11.5V≤Vin≤ -26V -- -- 0.5 mA
Quiescent Current Change ∆Iq
5mA≤Iout≤350mA -- -- 0.5
o
Output Noise Voltage Vn 10Hz≤f≤100KHz, Tj=25 C -- 60 -- uV
Ripple Rejection Ratio RR f=120Hz, -12V≤Vin≤ -22V 54 63 -- dB
o
Voltage Drop Vdrop Iout=350mA, Tj=25 C -- 2 -- V
o
Peak Output Current Io peak Tj=25 C -- 0.7 -- A
Temperature Coefficient of o o mV/
∆Vout/ ∆Tj Iout=5mA, 0 C≤Tj≤125 C -- -0.4 -- o
Output Voltage C
z Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as
possible, and thermal effects must be taken into account separately.
z This specification applies only for DC power dissipation permitted by absolute maximum ratings.

TS79M00 series 3-7 2003/12 rev. A

 TS79M12 Electrical Characteristics
o o
(Vin= -19V, Iout=350mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)

Parameter Symbol Test Conditions Min Typ Max Unit

o
Tj=25 C - 11.53 - 12 - 12.48
Output Voltage Vout -14.5V≤Vin≤ -27V, - 11.42 - 12 - 12.60 V
5mA≤Iout≤350mA, PD ≤5W
-14.5V≤Vin≤ -30V, -- 8 50
Line Regulation REGline Tj=25 oC
Io=200mA mV

o 5mA≤Iout≤500mA -- 25 240
Load Regulation REGload Tj=25 C
0mA≤Iout≤200mA -- 10 120
o
Quiescent Current Iq Tj=25 C, Iout=0 -- 4 8
-14.5V≤Vin≤ -30V -- -- 0.5 mA
Quiescent Current Change ∆Iq
5mA≤Iout≤200mA -- -- 0.5
o
Output Noise Voltage Vn 10Hz≤f≤100KHz, Tj=25 C -- 70 -- uV
Ripple Rejection Ratio RR f=120Hz, -15V≤Vin≤ -25V 54 60 -- dB
Voltage Drop Vdrop Iout=350mA, Tj=25 oC -- 2 -- V
o
Peak Output Current Io peak Tj=25 C -- 0.7 -- A
Temperature Coefficient of o o mV/
∆Vout/ ∆Tj Iout=5mA, 0 C≤Tj≤125 C -- -0.8 -- o
Output Voltage C

TS79M15 Electrical Characteristics

o o
(Vin= -23V, Iout=350mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)

Parameter Test Conditions Min Typ Max Unit

o
Tj=25 C - 14.42 - 15 - 15.60
Output Voltage Vout -17.5V≤Vin≤ -30V, - 14.28 - 15 - 15.75 V
5mA≤Iout≤350mA, PD ≤5W
Tj=25 -17.5V≤Vin≤ -30V, -- 8 50
Line Regulation REGline o
C Io=200mA mV
Tj=25 5mA≤Iout≤500mA -- 25 300
Load Regulation REGload o
C 5mA≤Iout≤200mA -- 10 150
Quiescent Current Iq Tj=25 oC, Iout=0 -- 5 8
-17.5V≤Vin≤ -30V -- -- 0.5 mA
Quiescent Current Change ∆Iq
5mA≤Iout≤350mA -- -- 0.5
o
Output Noise Voltage Vn 10Hz≤f≤100KHz, Tj=25 C -- 90 -- uV
Ripple Rejection Ratio RR f=120Hz, -18V≤Vin≤ -28V 54 60 -- dB
o
Voltage Drop Vdrop Iout=350mA, Tj=25 C -- 2 -- V
o
Peak Output Current Io peak Tj=25 C -- 0.7 -- A
Temperature Coefficient of o o mV/
∆Vout/ ∆Tj Iout=5mA, 0 C≤Tj≤125 C -- -1.0 -- o
Output Voltage C
z Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as
possible, and thermal effects must be taken into account separately.
z This specification applies only for DC power dissipation permitted by absolute maximum ratings.

TS79M00 series 4-7 2003/12 rev. A

 TS79M18 Electrical Characteristics
o o
(Vin= -27V, Iout=350mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)

Parameter Symbol Test Conditions Min Typ Max Unit

o
Tj=25 C - 17.30 - 18 - 18.72
Output Voltage Vout -21V≤Vin≤ -33V, - 17.14 - 18 - 18.90 V
5mA≤Iout≤350mA, PD ≤5W
-21V≤Vin≤ -33V, -- 8 50
Line Regulation REGline Tj=25 oC
Io=200mA mV

o 5mA≤Iout≤500mA -- 25 360
Load Regulation REGload Tj=25 C
5mA≤Iout≤200mA -- 10 180
o
Quiescent Current Iq Tj=25 C, Iout=0 -- 5 8
-21V≤Vin≤ -33V -- -- 0.5 mA
Quiescent Current Change ∆Iq
5mA≤Iout≤350nA -- -- 0.5
o
Output Noise Voltage Vn 10Hz≤f≤100KHz, Tj=25 C -- 110 -- uV
Ripple Rejection Ratio RR f=120Hz, -21V≤Vin≤ -31V 54 60 -- dB
Voltage Drop Vdrop Iout=350mA, Tj=25 oC -- 2 -- V
o
Peak Output Current Io peak Tj=25 C -- 0.7 -- A
Temperature Coefficient of o o mV/
∆Vout/ ∆Tj Iout=5mA, 0 C≤Tj≤125 C -- -1.0 -- o
Output Voltage C

TS79M24 Electrical Characteristics

o o
(Vin=- 33V, Iout=350mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)

Parameter Symbol Test Conditions Min Typ Max Unit

o
Tj=25 C - 23.07 - 24 - 24.96
Output Voltage Vout -27V≤Vin≤ -38V, - 22.85 - 24 - 25.20 V
5mA≤Iout≤350mA, PD ≤5W

o -27V≤Vin≤ -38V, -- 10 50
Line Regulation REGline Tj=25 C
Io=200mA mV
5mA≤Iout≤500mA -- 30 480
Load Regulation REGload Tj=25 oC
5mA≤Iout≤200mA -- 10 240
Quiescent Current Iq Iout=0, Tj=25 oC -- 5 9
-27V≤Vin≤ -38V -- -- 0.5 mA
Quiescent Current Change ∆Iq
5mA≤Iout≤350mA -- -- 0.5
o
Output Noise Voltage Vn 10Hz≤f≤100KHz, Tj=25 C -- 170 -- uV
Ripple Rejection Ratio RR f=120Hz, -27V≤Vin≤ -37V 50 60 -- dB
o
Voltage Drop Vdrop Iout=350mA, Tj=25 C -- 2 -- V
o
Peak Output Current Io peak Tj=25 C -- 0.7 -- A
Temperature Coefficient of o o mV/
∆Vout/ ∆Tj Iout=5mA, 0 C≤Tj≤125 C -- -1.0 -- o
Output Voltage C
z Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as
possible, and thermal effects must be taken into account separately.
z This specification applies only for DC power dissipation permitted by absolute maximum ratings.

TS79M00 series 5-7 2003/12 rev. A

Electrical Characteristics Curve
FIGURE 1 - Worst Case Power Dissipation v.s. FIGURE 2 - Peak Output Current v.s.
Ambient Temperature Dropout Voltage

FIGURE 3 – Quiescent Current v.s. FIGURE 4 –Dropout Voltage v.s.

Input Voltage Junction Temperature

FIGURE 5 – Quiescent Current v.s. FIGURE 6 – TO-252 Thermal Resistance and

Output Current Pd(max) v.s. P.C.B Copper Length

TS79M00 series 6-7 2003/12 rev. A

 TO-220 Mechanical Drawing

B K
A TO-220 DIMENSION
L MILLIMETERS INCHES
DIM
MIN MAX MIN MAX

C
P A 10.000 10.500 0.394 0.413
B 3.240 4.440 0.128 0.175
C 2.440 2.940 0.096 0.116
J
D - 6.350 - 0.250
I E 0.381 1.106 0.015 0.040
F 2.345 2.715 0.092 0.058
M G 4.690 5.430 0.092 0.107
H 12.700 14.732 0.500 0.581
D
I 8.382 9.017 0.330 0.355
H J 14.224 16.510 0.560 0.650
K 3.556 4.826 0.140 0.190
L 0.508 1.397 0.020 0.055
M 27.700 29.620 1.060 1.230
N 2.032 2.921 0.080 0.115
O O 0.255 0.610 0.010 0.024
E
F N P 5.842 6.858 0.230 0.270
G

TO-252 Mechanical Drawing

J E
A TO-252 DIMENSION
F
MILLIMETERS INCHES
DIM
MIN MAX MIN MAX
A 6.570 6.840 0.259 0.269
I B 9.250 10.400 0.364 0.409
B C 0.550 0.700 0.022 0.028
D 2.560 2.670 0.101 0.105
E 2.300 2.390 0.090 0.094
F 0.490 0.570 0.019 0.022
G G 1.460 1.580 0.057 0.062

D C H 0.520 0.570 0.020 0.022

H
I 5.340 5.550 0.210 0.219
J 1.460 1.640 0.057 0.065

TS79M00 series 7-7 2003/12 rev. A