Scribd
Upload
2 views

CONFIGURATION OSPF

The document outlines the configuration process for four routers using the OSPF protocol. Each router is configured with specific IP addresses for their interfaces and OSPF networks, followed by saving the configurations. The document also includes status messages indicating the state changes of interfaces and successful pings between routers.

Uploaded by

maximeseingue4
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
2 views

CONFIGURATION OSPF

The document outlines the configuration process for four routers using the OSPF protocol. Each router is configured with specific IP addresses for their interfaces and OSPF networks, followed by saving the configurations. The document also includes status messages indicating the state changes of interfaces and successful pings between routers.

Uploaded by

maximeseingue4
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 9

CONFIGURATION A L’AIDE DU PROTOCOLE OSPF

ROUTEUR 1
Router>EN
Router>ENable
Router#CONF T
Router#CONF Terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#INT S
Router(config)#INT Serial 0/0/0
Router(config-if)#IP ADD
Router(config-if)#IP ADDress 204.27.1.1 255.255.255.0
Router(config-if)#NO SH
Router(config-if)#NO SHutdown

%LINK-5-CHANGED: Interface Serial0/0/0, changed state to down


Router(config-if)#EXIT
Router(config)#INT FA
Router(config)#INT FAstEthernet 0/0
Router(config-if)#
Router(config-if)#IP ADD
Router(config-if)#IP ADDress 195.132.92.1 255.255.255.0
Router(config-if)#NO SH
Router(config-if)#NO SHutdown

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#EXIT
Router(config)#
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up

Router(config)#RO
Router(config)#ROuter OS
Router(config)#ROuter OSpf 1
Router(config-router)#NET
Router(config-router)#NETwork 204.27.1.0 0.0.0.255 AR
Router(config-router)#NETwork 204.27.1.0 0.0.0.255 ARea 0
Router(config-router)#NET
Router(config-router)#NETwork 195.132.92.0 0.0.0.255 AR
Router(config-router)#NETwork 195.132.92.0 0.0.0.255 ARea 0
Router(config-router)#EXIT
Router(config)#EXIT
Router#
%SYS-5-CONFIG_I: Configured from console by console

Router#COP
Router#COPy RU
Router#COPy RUnning-config ST
Router#COPy RUnning-config STartup-config
Destination filename [startup-config]?
Building configuration...
[OK]
Router#
00:20:04: %OSPF-5-ADJCHG: Process 1, Nbr 204.27.1.2 on Serial0/0/0 from LOADING to
FULL, Loading Done

Router con0 is now available


Press RETURN to get started.

ROUTEUR 2
Router>EN
Router>ENable
Router#CONF T
Router#CONF Terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#INT S
Router(config)#INT Serial 0/0/0
Router(config-if)#IP ADD
Router(config-if)#IP ADDress 204.27.1.1 255.255.255.0
Router(config-if)#NO SH
Router(config-if)#NO SHutdown

%LINK-5-CHANGED: Interface Serial0/0/0, changed state to down


Router(config-if)#EXIT
Router(config)#INT FA
Router(config)#INT FAstEthernet 0/0
Router(config-if)#
Router(config-if)#IP ADD
Router(config-if)#IP ADDress 195.132.92.1 255.255.255.0
Router(config-if)#NO SH
Router(config-if)#NO SHutdown

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#EXIT
Router(config)#
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up

Router(config)#RO
Router(config)#ROuter OS
Router(config)#ROuter OSpf 1
Router(config-router)#NET
Router(config-router)#NETwork 204.27.1.0 0.0.0.255 AR
Router(config-router)#NETwork 204.27.1.0 0.0.0.255 ARea 0
Router(config-router)#NET
Router(config-router)#NETwork 195.132.92.0 0.0.0.255 AR
Router(config-router)#NETwork 195.132.92.0 0.0.0.255 ARea 0
Router(config-router)#EXIT
Router(config)#EXIT
Router#
%SYS-5-CONFIG_I: Configured from console by console

Router#COP
Router#COPy RU
Router#COPy RUnning-config ST
Router#COPy RUnning-config STartup-config
Destination filename [startup-config]?
Building configuration...
[OK]
Router#
00:20:04: %OSPF-5-ADJCHG: Process 1, Nbr 204.27.1.2 on Serial0/0/0 from LOADING to
FULL, Loading Done

Router con0 is now available

Press RETURN to get started.

ROUTEUR 3
Router>EN
Router>ENable
Router#CONF
Router#CONFigure T
Router#CONFigure Terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#
Router(config)#INT S
Router(config)#INT Serial 0/0/0
Router(config-if)#IP ADD
Router(config-if)#IP ADDress 193.64.203.2 255.255.255.0
Router(config-if)#NO SH
Router(config-if)#NO SHutdown

Router(config-if)#
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up

Router(config-if)#EXIT
Router(config)#INT F
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up

Router(config)#INT FastEthernet 0/0


Router(config-if)#IP ADD
Router(config-if)#IP ADDress 197.64.203.1 255.255.255.0
Router(config-if)#NO SH
Router(config-if)#NO SHutdown

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#EXIT
Router(config)#INT S
Router(config)#INT Serial 0/0/1
Router(config-if)#IP ADD
Router(config-if)#IP ADDress 200.18.30.1 255.255.255.0
Router(config-if)#NO SH
Router(config-if)#NO SHutdown

%LINK-5-CHANGED: Interface Serial0/0/1, changed state to down


Router(config-if)#EXIT
Router(config)#
%LINK-5-CHANGED: Interface Serial0/0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/1, changed state to up


Router(config)#
Router(config)#RO
Router(config)#ROuter OS
Router(config)#ROuter OSpf 1
Router(config-router)#NET
Router(config-router)#NETwork 193.64.203.0 0.0.0.255 AR
Router(config-router)#NETwork 193.64.203.0 0.0.0.255 ARea 0
Router(config-router)#NET
Router(config-router)#NETwork
00:21:18: %OSPF-5-ADJCHG: Process 1, Nbr 204.27.1.2 on Serial0/0/0 from LOADING to
FULL, LoadiNETwork
% Incomplete command.
Router(config-router)#NET
Router(config-router)#NETwork 200.18.30.0 0.0.0.255 AR
Router(config-router)#NETwork 200.18.30.0 0.0.0.255 ARea 0
Router(config-router)#NET
Router(config-router)#NETwork 197.64.203.0 0.0.0.255 AR
Router(config-router)#NETwork 197.64.203.0 0.0.0.255 ARea 0
Router(config-router)#EXIT
Router(config)#EXIT
Router#
%SYS-5-CONFIG_I: Configured from console by console

Router#CO
Router#COP
Router#COPy RU
Router#COPy RUnning-config ST
Router#COPy RUnning-config STartup-config
Destination filename [startup-config]?
Building configuration...
[OK]
Router#
00:23:23: %OSPF-5-ADJCHG: Process 1, Nbr 200.18.30.2 on Serial0/0/1 from LOADING to
FULL, Loading Done

Router con0 is now available


Press RETURN to get started.

ROUTEUR 4

Router>EN
Router>ENable
Router#CONF T
Router#CONF Terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#INT S
Router(config)#INT Serial 0/0/0
Router(config-if)#IP ADD
Router(config-if)#IP ADDress 200.18.30.2 255.255.255.0
Router(config-if)#NO SH
Router(config-if)#NO SHutdown

Router(config-if)#
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up

Router(config-if)#EXIT
Router(config)#INT
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up

% Incomplete command.
Router(config)#INT F
Router(config)#INT FastEthernet 0/0
Router(config-if)#IP ADD
Router(config-if)#IP ADDress 196.92.10.1 255.255.255.0
Router(config-if)#NO SH
Router(config-if)#NO SHutdown

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#EXIT
Router(config)#RO
Router(config)#ROuter OS
Router(config)#ROuter OSpf 1
Router(config-router)#NET
% Incomplete command.
Router(config-router)#NET
Router(config-router)#NETwork 200.18.30.0 0.0.0.255 AR
Router(config-router)#NETwork 200.18.30.0 0.0.0.255 ARea 0
Router(config-router)#NET
Router(config-router)#NETwork 196.9
00:23:11: %OSPF-5-ADJCHG: Process 1, Nbr 200.18.30.1 on Serial0/0/0 from LOADING to
FULL, NETwo
% Incomplete command.
Router(config-router)#NET
Router(config-router)#NETwork 196.92.10.0 0.0.0.255 AR
Router(config-router)#NETwork 196.92.10.0 0.0.0.255 ARea 0
Router(config-router)#EXIT
Router(config)#EXIT
Router#
%SYS-5-CONFIG_I: Configured from console by console

Router#COP
Router#COPy RU
Router#COPy RUnning-config ST
Router#COPy RUnning-config STartup-config
Destination filename [startup-config]?
Building configuration...
[OK]
Router#ping 200.18.30.1

Type escape sequence to abort.


Sending 5, 100-byte ICMP Echos to 200.18.30.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/5 ms

Router#ping 193.64.203.2

Type escape sequence to abort.


Sending 5, 100-byte ICMP Echos to 193.64.203.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/3 ms

Router#ping 193.64.203.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 193.64.203.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 2/3/10 ms

Router#

Router con0 is now available

Press RETURN to get started.

You might also like