SAFETY DATA SHEET

According to EC No 1907/2006 as amended as at the date of this SDS

Shell Morlina S2 BL 10
Version 1.3 Revision Date 01.02.2021 Print Date 02.02.2021

SECTION 1: Identification of the substance/mixture and of the company/undertaking

1.1 Product identifier

Trade name : Shell Morlina S2 BL 10
Product code : 001F8471
UFI : 73P0-U0G5-600K-SJYE

1.2 Relevant identified uses of the substance or mixture and uses advised against
Use of the : Synthetic Industrial Gear Oil
Substance/Mixture
Uses advised against : This product must not be used in applications other than those
listed in Section 1 without first seeking the advice of the
supplier.

1.3 Details of the supplier of the safety data sheet

Manufacturer/Supplier : Société des Pétroles Shell
Tour Pacific
11/13 cours Valmy - La Défense 7
F-92977 PARIS LA DEFENSE
Telephone : (+33) 0969366018
Telefax : (+33) 0969366030
Email Contact for Safety Data : If you have any enquiries about the content of this SDS
Sheet please email [email protected]

1.4 Emergency telephone number

: Shell (en France 24/24h): 0800 33 86 86 (+33 4 82 90 75 50)
ORFILA (INRS): + 33 (0)1 45 42 59 59

SECTION 2: Hazards identification

2.1 Classification of the substance or mixture

Classification (REGULATION (EC) No 1272/2008)
Aspiration hazard, Category 1 H304: May be fatal if swallowed and enters
airways.
2.2 Label elements

Labelling (REGULATION (EC) No 1272/2008)

Hazard pictograms :

Signal word : Danger

1 / 20 800010033376
FR
SAFETY DATA SHEET
According to EC No 1907/2006 as amended as at the date of this SDS
Shell Morlina S2 BL 10
Version 1.3 Revision Date 01.02.2021 Print Date 02.02.2021

Hazard statements : PHYSICAL HAZARDS:

Not classified as a physical hazard
according to CLP criteria.
HEALTH HAZARDS:
H304 May be fatal if swallowed and enters
airways.
ENVIRONMENTAL HAZARDS:
Not classified as environmental hazard
according to CLP criteria.

Precautionary statements : Prevention:

No precautionary phrases.
Response:
P331 Do NOT induce vomiting.
P301 + P310 IF SWALLOWED: Immediately call a
POISON CENTER/ doctor.
Storage:
P405 Store locked up.
Disposal:
P501 Dispose of contents/ container to an
approved waste disposal plant.

Hazardous components which must be listed on the label:

Contains Distillates (Fischer - Tropsch), heavy, C18-50 - branched, cyclic and linear.

Sensitising components :
Contains N-phenyl-1-naphthylamine.
May produce an allergic reaction.

2.3 Other hazards

This mixture does not contain any REACH registered substances that are assessed to be a PBT or a
vPvB.
Prolonged or repeated skin contact without proper cleaning can clog the pores of the skin resulting in
disorders such as oil acne/folliculitis.
Used oil may contain harmful impurities.
Not classified as flammable but will burn.

SECTION 3: Composition/information on ingredients

3.2 Mixtures
Chemical nature : Synthetic base oil and additives.

Hazardous components
Chemical name CAS-No. Classification Concentration
EC-No. (REGULATION (% w/w)
Registration (EC) No
number 1272/2008)

2 / 20 800010033376
FR
SAFETY DATA SHEET
According to EC No 1907/2006 as amended as at the date of this SDS
Shell Morlina S2 BL 10
Version 1.3 Revision Date 01.02.2021 Print Date 02.02.2021

Distillates (Fischer - 848301-69-9 Asp. Tox.1; H304 0 - 90

Tropsch), heavy, C18- 482-220-0
50 – branched, cyclic 01-0000020163-82
and linear
Kerosine Asp. Tox.1; H304 5 - 15
Not Assigned EUH066
926-141-6

N-phenyl-1- 90-30-2 Acute Tox.4; H302 0,1 - 0,9

naphthylamine 201-983-0 Skin Sens.1B;
H317
STOT RE2; H373
Aquatic Acute1;
H400
Aquatic Chronic1;
H410
For explanation of abbreviations see section 16.

SECTION 4: First aid measures

4.1 Description of first aid measures

Protection of first-aiders : When administering first aid, ensure that you are wearing the
appropriate personal protective equipment according to the
incident, injury and surroundings.

If inhaled : No treatment necessary under normal conditions of use.

If symptoms persist, obtain medical advice.

In case of skin contact : Remove contaminated clothing. Flush exposed area with
water and follow by washing with soap if available.
If persistent irritation occurs, obtain medical attention.

In case of eye contact : Flush eye with copious quantities of water.

Remove contact lenses, if present and easy to do. Continue
rinsing.
If persistent irritation occurs, obtain medical attention.

If swallowed : Call emergency number for your location / facility.

If swallowed, do not induce vomiting: transport to nearest
medical facility for additional treatment. If vomiting occurs
spontaneously, keep head below hips to prevent aspiration.
If any of the following delayed signs and symptoms appear
within the next 6 hours, transport to the nearest medical
facility: fever greater than 101° F (38.3°C), shortness of
breath, chest congestion or continued coughing or wheezing.

4.2 Most important symptoms and effects, both acute and delayed
Symptoms : If material enters lungs, signs and symptoms may include
coughing, choking, wheezing, difficulty in breathing, chest

3 / 20 800010033376
FR
SAFETY DATA SHEET
According to EC No 1907/2006 as amended as at the date of this SDS
Shell Morlina S2 BL 10
Version 1.3 Revision Date 01.02.2021 Print Date 02.02.2021

congestion, shortness of breath, and/or fever.

The onset of respiratory symptoms may be delayed for
several hours after exposure.
Defatting dermatitis signs and symptoms may include a
burning sensation and/or a dried/cracked appearance.
Ingestion may result in nausea, vomiting and/or diarrhoea.

4.3 Indication of any immediate medical attention and special treatment needed
Treatment : Potential for chemical pneumonitis.
Call a doctor or poison control center for guidance.

SECTION 5: Firefighting measures

5.1 Extinguishing media

Suitable extinguishing media : Foam, water spray or fog. Dry chemical powder, carbon
dioxide, sand or earth may be used for small fires only.
Unsuitable extinguishing : Do not use water in a jet.
media
5.2 Special hazards arising from the substance or mixture
Specific hazards during : Hazardous combustion products may include: A complex
firefighting mixture of airborne solid and liquid particulates and gases
(smoke). Carbon monoxide may be evolved if incomplete
combustion occurs. Unidentified organic and inorganic
compounds.
5.3 Advice for firefighters
Special protective equipment : Proper protective equipment including chemical resistant
for firefighters gloves are to be worn; chemical resistant suit is indicated if
large contact with spilled product is expected. Self-Contained
Breathing Apparatus must be worn when approaching a fire in
a confined space. Select fire fighter's clothing approved to
relevant Standards (e.g. Europe: EN469).
Specific extinguishing : Use extinguishing measures that are appropriate to local
methods circumstances and the surrounding environment.

SECTION 6: Accidental release measures

6.1 Personal precautions, protective equipment and emergency procedures

Personal precautions : 6.1.1 For non emergency personnel:
Avoid contact with skin and eyes.
6.1.2 For emergency responders:
Avoid contact with skin and eyes.

4 / 20 800010033376
FR
SAFETY DATA SHEET
According to EC No 1907/2006 as amended as at the date of this SDS
Shell Morlina S2 BL 10
Version 1.3 Revision Date 01.02.2021 Print Date 02.02.2021

6.2 Environmental precautions

Environmental precautions : Use appropriate containment to avoid environmental
contamination. Prevent from spreading or entering drains,
ditches or rivers by using sand, earth, or other appropriate
barriers.

6.3 Methods and materials for containment and cleaning up

Methods for cleaning up : Slippery when spilt. Avoid accidents, clean up immediately.
Prevent from spreading by making a barrier with sand, earth
or other containment material.
Reclaim liquid directly or in an absorbent.
Soak up residue with an absorbent such as clay, sand or other
suitable material and dispose of properly.

6.4 Reference to other sections

For guidance on selection of personal protective equipment see Section 8 of this Safety Data Sheet.,
For guidance on disposal of spilled material see Section 13 of this Safety Data Sheet.

SECTION 7: Handling and storage

General Precautions : Use local exhaust ventilation if there is risk of inhalation of

vapours, mists or aerosols.
Use the information in this data sheet as input to a risk
assessment of local circumstances to help determine
appropriate controls for safe handling, storage and disposal of
this material.

7.1 Precautions for safe handling

Advice on safe handling : Avoid prolonged or repeated contact with skin.
Avoid inhaling vapour and/or mists.
When handling product in drums, safety footwear should be
worn and proper handling equipment should be used.
Properly dispose of any contaminated rags or cleaning
materials in order to prevent fires.

7.2 Conditions for safe storage, including any incompatibilities

Other data : Keep container tightly closed and in a cool, well-ventilated
place. Use properly labeled and closable containers.

Store at ambient temperature.

Refer to section 15 for any additional specific legislation

covering the packaging and storage of this product.

Packaging material : Suitable material: For containers or container linings, use mild
steel or high density polyethylene.
Unsuitable material: PVC.

5 / 20 800010033376
FR
SAFETY DATA SHEET
According to EC No 1907/2006 as amended as at the date of this SDS
Shell Morlina S2 BL 10
Version 1.3 Revision Date 01.02.2021 Print Date 02.02.2021

Container Advice : Polyethylene containers should not be exposed to high

temperatures because of possible risk of distortion.

7.3 Specific end use(s)

Specific use(s) : Not applicable

SECTION 8: Exposure controls/personal protection

8.1 Control parameters

Occupational Exposure Limits

Value type (Form

Components CAS-No. Control parameters Basis
of exposure)
Oil mist, mineral TWA 5 mg/m3 US. ACGIH
Threshold
Limit Values

Biological occupational exposure limits

No biological limit allocated.
Monitoring Methods
Monitoring of the concentration of substances in the breathing zone of workers or in the general
workplace may be required to confirm compliance with an OEL and adequacy of exposure controls.
For some substances biological monitoring may also be appropriate.
Validated exposure measurement methods should be applied by a competent person and samples
analysed by an accredited laboratory.
Examples of sources of recommended exposure measurement methods are given below or contact
the supplier. Further national methods may be available.

National Institute of Occupational Safety and Health (NIOSH), USA: Manual of Analytical Methods
http://www.cdc.gov/niosh/

Occupational Safety and Health Administration (OSHA), USA: Sampling and Analytical Methods
http://www.osha.gov/

Health and Safety Executive (HSE), UK: Methods for the Determination of Hazardous Substances
http://www.hse.gov.uk/

Institut für Arbeitsschutz Deutschen Gesetzlichen Unfallversicherung (IFA) , Germany

http://www.dguv.de/inhalt/index.jsp

L'Institut National de Recherche et de Securité, (INRS), France http://www.inrs.fr/accueil

8.2 Exposure controls

Engineering measuresThe level of protection and types of controls necessary will vary depending
upon potential exposure conditions. Select controls based on a risk assessment of local
circumstances. Appropriate measures include:

6 / 20 800010033376
FR
SAFETY DATA SHEET
According to EC No 1907/2006 as amended as at the date of this SDS
Shell Morlina S2 BL 10
Version 1.3 Revision Date 01.02.2021 Print Date 02.02.2021

Adequate ventilation to control airborne concentrations.

Where material is heated, sprayed or mist formed, there is greater potential for airborne
concentrations to be generated.

General Information:
Define procedures for safe handling and maintenance of controls.
Educate and train workers in the hazards and control measures relevant to normal activities
associated with this product.
Ensure appropriate selection, testing and maintenance of equipment used to control exposure, e.g.
personal protective equipment, local exhaust ventilation.
Drain down system prior to equipment break-in or maintenance.
Retain drain downs in sealed storage pending disposal or subsequent recycle.
Always observe good personal hygiene measures, such as washing hands after handling the material
and before eating, drinking, and/or smoking. Routinely wash work clothing and protective equipment
to remove contaminants. Discard contaminated clothing and footwear that cannot be cleaned.
Practice good housekeeping.
Do not ingest. If swallowed, then seek immediate medical assistance
Personal protective equipment
The provided information is made in consideration of the PPE directive (Council Directive
89/686/EEC) and the CEN European Committee for Standardisation (CEN) standards.

Personal protective equipment (PPE) should meet recommended national standards. Check with
PPE suppliers.

Eye protection : If material is handled such that it could be splashed into eyes,
protective eyewear is recommended.
Approved to EU Standard EN166.

Hand protection

Remarks : Where hand contact with the product may occur the use of
gloves approved to relevant standards (e.g. Europe: EN374,
US: F739) made from the following materials may provide
suitable chemical protection. PVC, neoprene or nitrile rubber
gloves Suitability and durability of a glove is dependent on
usage, e.g. frequency and duration of contact, chemical
resistance of glove material, dexterity. Always seek advice
from glove suppliers. Contaminated gloves should be
replaced. Personal hygiene is a key element of effective hand
care. Gloves must only be worn on clean hands. After using
gloves, hands should be washed and dried thoroughly.
Application of a non-perfumed moisturizer is recommended.

For continuous contact we recommend gloves with

breakthrough time of more than 240 minutes with preference
for > 480 minutes where suitable gloves can be identified. For
short-term/splash protection we recommend the same but
recognize that suitable gloves offering this level of protection
may not be available and in this case a lower breakthrough

7 / 20 800010033376
FR
SAFETY DATA SHEET
According to EC No 1907/2006 as amended as at the date of this SDS
Shell Morlina S2 BL 10
Version 1.3 Revision Date 01.02.2021 Print Date 02.02.2021

time maybe acceptable so long as appropriate maintenance

and replacement regimes are followed. Glove thickness is not
a good predictor of glove resistance to a chemical as it is
dependent on the exact composition of the glove material.
Glove thickness should be typically greater than 0.35 mm
depending on the glove make and model.

Skin and body protection : Skin protection is not ordinarily required beyond standard
work clothes.
It is good practice to wear chemical resistant gloves.

Respiratory protection : No respiratory protection is ordinarily required under normal

conditions of use.
In accordance with good industrial hygiene practices,
precautions should be taken to avoid breathing of material.
If engineering controls do not maintain airborne
concentrations to a level which is adequate to protect worker
health, select respiratory protection equipment suitable for the
specific conditions of use and meeting relevant legislation.
Check with respiratory protective equipment suppliers.
Where air-filtering respirators are suitable, select an
appropriate combination of mask and filter.
Select a filter suitable for combined particulate/organic gases
and vapours [Type A/Type P boiling point > 65°C (149°F)]
meeting EN14387 and EN143.

Thermal hazards : Not applicable

Environmental exposure controls

General advice : Local guidelines on emission limits for volatile substances
must be observed for the discharge of exhaust air containing
vapour.
Minimise release to the environment. An environmental
assessment must be made to ensure compliance with local
environmental legislation.
Information on accidental release measures are to be found in
section 6.
Take appropriate measures to fulfil the requirements of
relevant environmental protection legislation. Avoid
contamination of the environment by following advice given in
Section 6. If necessary, prevent undissolved material from
being discharged to waste water. Waste water should be
treated in a municipal or industrial waste water treatment plant
before discharge to surface water.

8 / 20 800010033376
FR
SAFETY DATA SHEET
According to EC No 1907/2006 as amended as at the date of this SDS
Shell Morlina S2 BL 10
Version 1.3 Revision Date 01.02.2021 Print Date 02.02.2021

SECTION 9: Physical and chemical properties

9.1 Information on basic physical and chemical properties

Appearance : liquid

Colour : colourless
Odour Threshold : Data not available
pH : Not applicable
pour point : Method: Unspecified
Not applicable
Melting / freezing point Data not available
Initial boiling point and boiling : > 280 °Cestimated value(s)
range
Flash point : >= 140 °C
Method: ASTM D92 (COC)

Evaporation rate : Data not available

Flammability (solid, gas) : Data not available

Upper explosion limit : Typical 10 %(V)

Lower explosion limit : Typical 1 %(V)

Vapour pressure : < 0,5 Pa (20 °C)

estimated value(s)
Relative vapour density : > 1estimated value(s)
Relative density : Data not available
Density : Method: Unspecified
Data not available
Solubility(ies)
Water solubility : negligible
Solubility in other solvents : Data not available

Partition coefficient: n- : log Pow: > 6(based on information on similar products)

octanol/water
Auto-ignition temperature : >
320 °C
Decomposition temperature : Data not available

Viscosity

9 / 20 800010033376
FR
SAFETY DATA SHEET
According to EC No 1907/2006 as amended as at the date of this SDS
Shell Morlina S2 BL 10
Version 1.3 Revision Date 01.02.2021 Print Date 02.02.2021

Viscosity, dynamic : Data not available

Viscosity, kinematic : 9 - 10 mm2/s (40,0 °C)
Method: ASTM D445

2,7 mm2/s (100 °C)

Method: ASTM D445

Explosive properties : Not classified

Oxidizing properties : Data not available

9.2 Other information

Conductivity : This material is not expected to be a static accumulator.

SECTION 10: Stability and reactivity

10.1 Reactivity
The product does not pose any further reactivity hazards in addition to those listed in the following
sub-paragraph.
10.2 Chemical stability
Stable.
No hazardous reaction is expected when handled and stored according to provisions
10.3 Possibility of hazardous reactions
Hazardous reactions : Reacts with strong oxidising agents.

10.4 Conditions to avoid

Conditions to avoid : Extremes of temperature and direct sunlight.

10.5 Incompatible materials

Materials to avoid : Strong oxidising agents.

10.6 Hazardous decomposition products

Hazardous decomposition : No decomposition if stored and applied as directed.
products

SECTION 11: Toxicological information

11.1 Information on toxicological effects

Basis for assessment : Information given is based on data on the components and
the toxicology of similar products.Unless indicated otherwise,

10 / 20 800010033376
FR
SAFETY DATA SHEET
According to EC No 1907/2006 as amended as at the date of this SDS
Shell Morlina S2 BL 10
Version 1.3 Revision Date 01.02.2021 Print Date 02.02.2021

the data presented is representative of the product as a

whole, rather than for individual component(s).
Information on likely routes of : Skin and eye contact are the primary routes of exposure
exposure although exposure may occur following accidental ingestion.

Acute toxicity
Product:
Acute oral toxicity : LD50 rat: > 5.000 mg/kg
Remarks: Low toxicity:
Based on available data, the classification criteria are not met.

Remarks: Aspiration into the lungs may cause chemical

pneumonitis which can be fatal.

Acute inhalation toxicity : Remarks: Based on available data, the classification criteria
are not met.

Acute dermal toxicity : LD50 Rabbit: > 5.000 mg/kg

Remarks: Low toxicity:
Based on available data, the classification criteria are not met.

Skin corrosion/irritation
Product:
Remarks: Slightly irritating to skin., Prolonged or repeated skin contact without proper cleaning
can clog the pores of the skin resulting in disorders such as oil acne/folliculitis., Based on
available data, the classification criteria are not met.

Serious eye damage/eye irritation

Product:
Remarks: Slightly irritating to the eye., Based on available data, the classification criteria are not
met.

Respiratory or skin sensitisation

Product:
Remarks: For respiratory and skin sensitisation:, Not a sensitiser., Based on available data, the
classification criteria are not met.

Components:
N-phenyl-1-naphthylamine:
Remarks: May cause an allergic skin reaction in sensitive individuals.

11 / 20 800010033376
FR
SAFETY DATA SHEET
According to EC No 1907/2006 as amended as at the date of this SDS
Shell Morlina S2 BL 10
Version 1.3 Revision Date 01.02.2021 Print Date 02.02.2021

Germ cell mutagenicity

Product:
: Remarks: Non mutagenic, Based on available data, the
classification criteria are not met.
Carcinogenicity
Product:

Remarks: Not a carcinogen., Based on available data, the classification criteria are not met.

Material GHS/CLP Carcinogenicity Classification

Highly refined mineral oil No carcinogenicity classification.

Reproductive toxicity

Product:
:
Remarks: Not a developmental toxicant., Does not impair
fertility., Based on available data, the classification criteria are
not met.

STOT - single exposure

Product:
Remarks: Based on available data, the classification criteria are not met.

STOT - repeated exposure

Product:
Remarks: Based on available data, the classification criteria are not met.

Aspiration toxicity
Product:
Aspiration into the lungs when swallowed or vomited may cause chemical pneumonitis which
can be fatal.

Further information
Product:
Remarks: Used oils may contain harmful impurities that have accumulated during use. The
concentration of such impurities will depend on use and they may present risks to health and the
environment on disposal., ALL used oil should be handled with caution and skin contact avoided

12 / 20 800010033376
FR
SAFETY DATA SHEET
According to EC No 1907/2006 as amended as at the date of this SDS
Shell Morlina S2 BL 10
Version 1.3 Revision Date 01.02.2021 Print Date 02.02.2021

as far as possible.

Remarks: Slightly irritating to respiratory system.

Remarks: Classifications by other authorities under varying regulatory frameworks may exist.

Summary on evaluation of the CMR properties

Germ cell mutagenicity- : This product does not meet the criteria for classification in
Assessment categories 1A/1B.

Carcinogenicity - : This product does not meet the criteria for classification in
Assessment categories 1A/1B.

Reproductive toxicity - : This product does not meet the criteria for classification in
Assessment categories 1A/1B.

SECTION 12: Ecological information

12.1 Toxicity

Basis for assessment : Ecotoxicological data have not been determined specifically
for this product.
Information given is based on a knowledge of the components
and the ecotoxicology of similar products.
Unless indicated otherwise, the data presented is
representative of the product as a whole, rather than for
individual component(s).(LL/EL/IL50 expressed as the
nominal amount of product required to prepare aqueous test
extract).
Product:
Toxicity to fish (Acute : Remarks: LL/EL/IL50 > 100 mg/l
toxicity) Practically non toxic:
Based on available data, the classification criteria are not met.

Toxicity to crustacean (Acute : Remarks: LL/EL/IL50 > 100 mg/l

toxicity) Practically non toxic:
Based on available data, the classification criteria are not met.

Toxicity to algae/aquatic : Remarks: LL/EL/IL50 > 100 mg/l

plants (Acute toxicity) Practically non toxic:
Based on available data, the classification criteria are not met.

Toxicity to fish (Chronic : Remarks: Data not available

toxicity)
Toxicity to crustacean : Remarks: Data not available
(Chronic toxicity)

13 / 20 800010033376
FR
SAFETY DATA SHEET
According to EC No 1907/2006 as amended as at the date of this SDS
Shell Morlina S2 BL 10
Version 1.3 Revision Date 01.02.2021 Print Date 02.02.2021

Toxicity to microorganisms :
(Acute toxicity) Remarks: Data not available

Components:
N-phenyl-1-naphthylamine :
M-Factor (Short-term (acute) : 1
aquatic hazard)
M-Factor (Long-term : 1
(chronic) aquatic hazard)
12.2 Persistence and degradability
Product:
Biodegradability : Remarks: Not readily biodegradable., Major constituents are
inherently biodegradable, but contains components that may
persist in the environment.

12.3 Bioaccumulative potential

Product:
Bioaccumulation : Remarks: Contains components with the potential to
bioaccumulate.

Partition coefficient: n- : log Pow: > 6Remarks: (based on information on similar

octanol/water products)
12.4 Mobility in soil
Product:
Mobility : Remarks: Liquid under most environmental conditions., If it
enters soil, it will adsorb to soil particles and will not be
mobile.
Remarks: Floats on water.
12.5 Results of PBT and vPvB assessment
Product:
Assessment : This mixture does not contain any REACH registered
substances that are assessed to be a PBT or a vPvB.
12.6 Other adverse effects
Product:
Additional ecological : Does not have ozone depletion potential, photochemical
information ozone creation potential or global warming potential., Product
is a mixture of non-volatile components, which will not be
released to air in any significant quantities under normal
conditions of use.
Poorly soluble mixture., Causes physical fouling of aquatic
organisms.

14 / 20 800010033376
FR
SAFETY DATA SHEET
According to EC No 1907/2006 as amended as at the date of this SDS
Shell Morlina S2 BL 10
Version 1.3 Revision Date 01.02.2021 Print Date 02.02.2021

SECTION 13: Disposal considerations

13.1 Waste treatment methods

Product : Recover or recycle if possible.
It is the responsibility of the waste generator to determine the
toxicity and physical properties of the material generated to
determine the proper waste classification and disposal
methods in compliance with applicable regulations.
Do not dispose into the environment, in drains or in water
courses

Waste product should not be allowed to contaminate soil or

ground water, or be disposed of into the environment.
Waste, spills or used product is dangerous waste.
Waste arising from a spillage or tank cleaning should be
disposed of in accordance with prevailing regulations,
preferably to a recognised collector or contractor. The
competence of the collector or contractor should be
established beforehand.
Do not dispose of tank water bottoms by allowing them to
drain into the ground. This will result in soil and groundwater
contamination.

MARPOL - see International Convention for the Prevention of

Pollution from Ships (MARPOL 73/78) which provides
technical aspects at controlling pollutions from ships.

Contaminated packaging : Dispose in accordance with prevailing regulations, preferably

to a recognized collector or contractor. The competence of
the collector or contractor should be established beforehand.
Disposal should be in accordance with applicable regional,
national, and local laws and regulations.

Local legislation

Waste catalogue :

EU Waste Disposal Code (EWC):

Waste Code :

13 02 06*

Remarks : Disposal should be in accordance with applicable regional,

national, and local laws and regulations.

Classification of waste is always the responsibility of the end

user.

15 / 20 800010033376
FR
SAFETY DATA SHEET
According to EC No 1907/2006 as amended as at the date of this SDS
Shell Morlina S2 BL 10
Version 1.3 Revision Date 01.02.2021 Print Date 02.02.2021

SECTION 14: Transport information

14.1 UN number
ADN : Not regulated as a dangerous good
ADR : Not regulated as a dangerous good
RID : Not regulated as a dangerous good
IMDG : Not regulated as a dangerous good
IATA : Not regulated as a dangerous good
14.2 Proper shipping name
ADN : Not regulated as a dangerous good
ADR : Not regulated as a dangerous good
RID : Not regulated as a dangerous good
IMDG : Not regulated as a dangerous good
IATA : Not regulated as a dangerous good
14.3 Transport hazard class
ADN : Not regulated as a dangerous good
ADR : Not regulated as a dangerous good
RID : Not regulated as a dangerous good
IMDG : Not regulated as a dangerous good
IATA : Not regulated as a dangerous good
14.4 Packing group
ADN : Not regulated as a dangerous good
CDNI Inland Water Waste : NST 3411 Mineral Lubricating Oils
Agreement
ADR : Not regulated as a dangerous good
RID : Not regulated as a dangerous good
IMDG : Not regulated as a dangerous good
IATA : Not regulated as a dangerous good
14.5 Environmental hazards
ADN : Not regulated as a dangerous good
ADR : Not regulated as a dangerous good
RID : Not regulated as a dangerous good
IMDG : Not regulated as a dangerous good
14.6 Special precautions for user
Remarks : Special Precautions: Refer to Section 7, Handling & Storage,
for special precautions which a user needs to be aware of or
needs to comply with in connection with transport.

14.7 Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code
Not applicable for product as supplied. MARPOL Annex 1 rules apply for bulk shipments by sea.

SECTION 15: Regulatory information

15.1 Safety, health and environmental regulations/legislation specific for the substance or mixture

16 / 20 800010033376
FR
SAFETY DATA SHEET
According to EC No 1907/2006 as amended as at the date of this SDS
Shell Morlina S2 BL 10
Version 1.3 Revision Date 01.02.2021 Print Date 02.02.2021

REACH - List of substances subject to authorisation : Product is not subject to

(Annex XIV) Authorisation under REACH.

Occupational Illnesses (R- : 36

461-3, France)
Volatile organic compounds : 0%

Other regulations : The following regulatory information is not intended to be

comprehensive and does not exempt the end user of the
product to refer to all official documents to determine its
obligations.

According type of product and quantity stored, check for

applicability of Code of environment: art. R511-9 -
Nomenclature of classified facilities.

Labour code : Exposure forbidden to certain works/products to

- Young people under 16 years old : art. D4153-25
- Young people under 18 years old : art. D4153-26, D4153-27
- Pregnant or breast-feeding women : art. D4152-10, D4152-
11
- Fixed term-contract or temporary staff : art. D4154-1,
D4154-2

Social security code - Article L.461-6, Appendix A, no. 601-15.

Labour code - Intensified medical supervision: Articles
R.4624-18 and R.4624-19, decree 2012-135 of 30.01.2012.

Regulation (EC) No 1907/2006 of the European Parliament

and of the Council of 18 December 2006 concerning the
Registration, Evaluation, Authorisation and Restriction of
Chemicals (REACH), annex XIV.
Regulation (EC) No 1907/2006 of the European Parliament
and of the Council of 18 December 2006 concerning the
Registration, Evaluation, Authorisation and Restriction of
Chemicals (REACH), annex XVII.
Directive 2004/37/EC on the protection of workers from the
risks related to exposure to carcinogens or mutagens at work
and its amendments.
Directive 1994/33/EC on the protection of young people at
work and its amendments.
Council Directive 92/85/EEC on the introduction of measures
to encourage improvements in the safety and health at work of
pregnant workers and workers who have recently given birth
or are breastfeeding and its amendments.

The components of this product are reported in the following inventories:

REACH : Notified with Restrictions.

17 / 20 800010033376
FR
SAFETY DATA SHEET
According to EC No 1907/2006 as amended as at the date of this SDS
Shell Morlina S2 BL 10
Version 1.3 Revision Date 01.02.2021 Print Date 02.02.2021

TSCA : All components listed.

15.2 Chemical safety assessment

No Chemical Safety Assessment has been carried out for this substance/mixture by the supplier.

SECTION 16: Other information

REGULATION (EC) No 1272/2008 Classification procedure:
Aspiration hazard, Category 1, H304 Expert judgement and weight of evidence
determination.

Full text of H-Statements

EUH066 Repeated exposure may cause skin dryness or cracking.
H302 Harmful if swallowed.
H304 May be fatal if swallowed and enters airways.
H317 May cause an allergic skin reaction.
H373 May cause damage to organs through prolonged or repeated exposure
if swallowed.
H400 Very toxic to aquatic life.
H410 Very toxic to aquatic life with long lasting effects.

Full text of other abbreviations

Acute Tox. Acute toxicity
Aquatic Acute Short-term (acute) aquatic hazard
Aquatic Chronic Long-term (chronic) aquatic hazard
Asp. Tox. Aspiration hazard
Skin Sens. Skin sensitisation
STOT RE Specific target organ toxicity - repeated exposure
Abbreviations and Acronyms : The quoted data are from, but not limited to, one or more
sources of information (e.g. toxicological data from Shell
Health Services, material suppliers’ data, CONCAWE, EU
IUCLID date base, EC 1272 regulation, etc).
The standard abbreviations and acronyms used in this
document can be looked up in reference literature (e.g.
scientific dictionaries) and/or websites.

ACGIH = American Conference of Governmental Industrial

Hygienists
ADR = European Agreement concerning the International
Carriage of Dangerous Goods by Road
AICS = Australian Inventory of Chemical Substances
ASTM = American Society for Testing and Materials
BEL = Biological exposure limits
BTEX = Benzene, Toluene, Ethylbenzene, Xylenes
CAS = Chemical Abstracts Service
CEFIC = European Chemical Industry Council
CLP = Classification Packaging and Labelling
COC = Cleveland Open-Cup
DIN = Deutsches Institut fur Normung
DMEL = Derived Minimal Effect Level

18 / 20 800010033376
FR
SAFETY DATA SHEET
According to EC No 1907/2006 as amended as at the date of this SDS
Shell Morlina S2 BL 10
Version 1.3 Revision Date 01.02.2021 Print Date 02.02.2021

DNEL = Derived No Effect Level

DSL = Canada Domestic Substance List
EC = European Commission
EC50 = Effective Concentration fifty
ECETOC = European Center on Ecotoxicology and
Toxicology Of Chemicals
ECHA = European Chemicals Agency
EINECS = The European Inventory of Existing Commercial
Chemical Substances
EL50 = Effective Loading fifty
ENCS = Japanese Existing and New Chemical Substances
Inventory
EWC = European Waste Code
GHS = Globally Harmonised System of Classification and
Labelling of Chemicals
IARC = International Agency for Research on Cancer
IATA = International Air Transport Association
IC50 = Inhibitory Concentration fifty
IL50 = Inhibitory Level fifty
IMDG = International Maritime Dangerous Goods
INV = Chinese Chemicals Inventory
IP346 = Institute of Petroleum test method N° 346 for the
determination of polycyclic aromatics DMSO-extractables
KECI = Korea Existing Chemicals Inventory
LC50 = Lethal Concentration fifty
LD50 = Lethal Dose fifty per cent.
LL/EL/IL = Lethal Loading/Effective Loading/Inhibitory loading
LL50 = Lethal Loading fifty
MARPOL = International Convention for the Prevention of
Pollution From Ships
NOEC/NOEL = No Observed Effect Concentration / No
Observed Effect Level
OE_HPV = Occupational Exposure - High Production Volume
PBT = Persistent, Bioaccumulative and Toxic
PICCS = Philippine Inventory of Chemicals and Chemical
Substances
PNEC = Predicted No Effect Concentration
REACH = Registration Evaluation And Authorisation Of
Chemicals
RID = Regulations Relating to International Carriage of
Dangerous Goods by Rail
SKIN_DES = Skin Designation
STEL = Short term exposure limit
TRA = Targeted Risk Assessment
TSCA = US Toxic Substances Control Act
TWA = Time-Weighted Average
vPvB = very Persistent and very Bioaccumulative

Further information
Training advice :

Provide adequate information, instruction and training for

19 / 20 800010033376
FR
SAFETY DATA SHEET
According to EC No 1907/2006 as amended as at the date of this SDS
Shell Morlina S2 BL 10
Version 1.3 Revision Date 01.02.2021 Print Date 02.02.2021

operators.

Other information : No Exposure Scenario annex is attached to this safety data

sheet. It is a non-classified mixture containing hazardous
substances as detailed in Section 3; relevant information from
Exposure Scenarios for the hazardous substances contained
have been integrated into the core sections 1-16 of this SDS.

A vertical bar (|) in the left margin indicates an amendment

from the previous version.

Sources of key data used to :

compile the Safety Data
Sheet
The quoted data are from, but not limited to, one or more
sources of information (e.g. toxicological data from Shell
Health Services, material suppliers’ data, CONCAWE, EU
IUCLID date base, EC 1272 regulation, etc).

This information is based on our current knowledge and is intended to describe the product for the
purposes of health, safety and environmental requirements only. It should not therefore be
construed as guaranteeing any specific property of the product.

20 / 20 800010033376
FR