Page 1

Intelligent power device (IPD)

MIP3E3SMY
Silicon MOS integrated circuit

■ Special feature Unit: mm

• Supports worldwide input to further reduce power consumption under light load 10.5 ± 0.5
4.5 ± 0.2

9.5 ± 0.2 1.4 ± 0.1

(Up to 50% reduction compared to MIP2Ex D series) ± 0.2 ± 0.2

8.0 ± 0.2
• Real-time protection is possible with built-in various protection circuit functions 2.8 1.5

• Built-in soft start ± 0.3

6.7
± 0.3 ± 0.2

φ 3.7 ± 0.2 2.8

15.4
■ Usage
• For switching power supply control
1.4 ± 0.1
2.5 ± 0.2
± 0.5

± 0.3 0.8 ± 0.1 0.6 +–0.2

■ Absolute maximum rating
0.1
13.54.2
(9.3)
Solder Dip
2.54 ± 0.3
item symbol Rated unit
5.08 ± 0.5
Drain voltage VD 700 V
Control voltage VC 8 V 1 32

Drain current 1: Control

ID 1.1 A
2: Source
Pointed drain current I DP 1.7 1.7 A 3: Drain
TO-220-A1 Package
Control current IC 0.1 A

Channel temperature T ch 150 °C

Model name display symbol: MIP3E3SMY
storage temperature T stg −55 to +150 °C

■ Block diagram

At startup Constant current for startup

Control Drain

Internal power supply

Light load detection
Timer
For intermittent oscillation control
Intermittent operation circuit

Error amplifier
Overheat protection
circuit S Q

Reboot trigger R Q

Oscillator Gate driver

power
Max. duty MOSFET
clock S Q

R Q

When on
Blanking
Pulse generation circuit

Drain current
For detection
over current
protection
Source

Date of issue: August 2003 SLB00054AJD 1

Page 2
MIP3E3SMY

■ Electrical characteristics T C = 25 ° C ± 3 ° C

item symbol conditions minimum standard maximum unit

Control function

Output frequency f OSC V C = V C (CNT) − 0.2 V, V D = 5 V 90 100 110 kHz

Maximum duty cycle MAXDC V C = V C (CNT) − 0.2 V, V D = 5 V 45.0 47.5 50.0 %%

PWM gain * GPWM V C = V C (CNT) 11 dB

Power supply

Pre-start operating current I C (SB) 1 V C <V C (ON) , V D = 5 V 0.2 0.4 0.7 mA

Current when light load is stopped I C (SB) 2 V C > V C (CNT) , V D = 5 V 0.2 0.5 0.8 mA
Operating current I C (OP) V C = V C (CNT) − 0.2 V, V D = 5 V 0.20 0.55 1.00 mA
Control terminal voltage at startup V C (ON) VD=5V 5.4 6.1 6.7 V
Control terminal voltage when stopped V C (OFF) VD=5V 4.1 4.8 5.4 V
Start / stop hysteresis voltage ∆V C VD=5V 0.8 1.3 1.3 1.8 1.8 V
Control terminal clamp voltage V C (CLP) I C = 1 mA, V D = 5 V 5.7 6.2. 6.7 V
Intermittent operation time ratio T SW / T TIM Four %%
Intermittent operating frequency f TIM 3 Hz
Control terminal charging current I C (CHG) V C = 0 V, V D = 40 V −3.6 −2.5 −1.0 mA

V C = 5 V, V D = 40 V −2.0 −1.0 − 0.4

Control voltage V C (CNT) VD=5V 5.4 5.8 6.3 V

Control voltage hysteresis * ∆V C (CNT) VD=5V Ten mV

Minimum drain voltage V D (MIN) 36 V
Protective function

Overcurrent protection detection I LIMIT 0.9 1.0 1.1 A

Blanking width when on * t on (BLK) 220 300 380 ns
Overcurrent protection delay time * t d (OCL) 50 100 150 ns
Overheat protection temperature * T OTP 130 140 °C

Latch reset voltage * V C reset 2.2 3.3 4.2 V

output

On resistance between drain and source R DS (on) I D = 0.2 A 6.0 6.0 7.5 7.5 Ω

Drain-source breaking current I DSS V DS = 650 V, V C = 6.5 V Ten 250 µA

Drain-source breakdown voltage V DSS I D = 1 mA, V C = 6.5 V 700 V

Rise time tr V C = V C (CNT) − 0.2 V, V D = 5 V 250 ns
Descent time tf V C = V C (CNT) − 0.2 V, V D = 5 V 50 ns
Thermal resistance between channel and case * R th (ch-c) 3.0 °C/W

Channel / ambient thermal resistance * R th (ch-a) 70 °C/W

Note) *: Design guarantee items

2 SLB00054AJD

Page 3

Technical information described in this manual and requests and precautions for using semiconductors

(1) When exporting the products and technologies described in this document that fall under the "Foreign Exchange and Foreign Trade Law", or holding them overseas.
When you put it out, you need the permission of the Japanese government.
(2) The technical information described in this manual shows the typical characteristics of the product and examples of applied circuits, and is intellectually understood by us or a third party.
It does not mean a guarantee or grant of license to property rights or other rights.

(3) The Company is not liable for any problems related to the rights owned by a third party due to the above.

(Four) The products described in this document are for standard use-general electronic equipment (office equipment, communication equipment, measuring equipment, home appliances, etc.)
It is intended to be used.
For applications that require special quality and reliability, and whose failure or malfunction may directly threaten human life or harm the human body.
For customers who are considering using it for specific purposes (aviation / space, transportation equipment, combustion equipment, life support equipment, safety equipment, etc.)
If you are considering using the product for purposes other than the standard applications intended by us, please contact our sales office in advance.

(Five) Please note that the products and product specifications described in this manual are subject to change without notice for improvement.
Please give me. Therefore, please request the latest product specifications or specifications in advance for final design, purchase, and use.
Please check it.

(6) When designing, please use within the guaranteed range, especially regarding the maximum rating, operating power supply voltage range, and heat dissipation characteristics.
Please. If the product is used beyond the guaranteed value, we will be liable for any defects in the equipment that occur after that.
not.
In addition, even if the product is used within the guaranteed value, the failure rate and failure mode normally predicted for semiconductor products should be taken into consideration.
Redundant design that prevents the equipment used from causing personal injury, fire accident, social damage, etc. due to the operation of our products, fire spread
Please take system measures such as designing measures and designing to prevent malfunctions.

(7) For products that require moisture-proof packaging, the conditions (storage period, after opening) agreed upon when individual specifications were exchanged.
Please use it while observing the leaving time etc.).

(8) Reproduction or reproduction of part or all of this document without our written consent is strictly prohibited.

Precautions for selling IPD

(1) This product is prohibited from being sold to overseas local companies under the sales contract with Power Integrations (USA).
(2) IPD sold by Matsushita Electric Industrial Co., Ltd. and authorized distributors is only for products manufactured by customers.
Please use it.
Resale, rental and sample shipment of IPD separately from customers is prohibited.
(3) When the sold IPD is provided to the company or other companies in Japan and overseas for consignment production, resale or lending is prevented.
There is an obligation to control the quantity of IPD to stop it.
(4) If there is a suspicion of violation of the above items (1), (2) and (3), IPD shipment will be stopped immediately and the end customer will be contacted.
And I would like to request the document presentation of the distribution route.
(Note) However, MIP5 **, MIP7 ** and MIP805 are not applicable.

Appendix "List of IPD sales support"

Target part number Available area Unsellable area application
MIP13 * MIP17 * MIP2 ***
Japanese domestic companies Western companies
MIP14 * MIP18 * MIP3 *** IPD for power supply
Japanese Asian companies Asian local company
MIP15 * MIP01 ** MIP9 *** IPD for DC / DC
(Investment ratio 50% or more) Other local companies
MIP16 * MIP02 **

MIP10 * MIP814 / 815/816 Japanese domestic companies (Note) Western companies

IPD for power supply
MIP11 * MIP811 / 812 Japanese Asian companies (Note) Asian local companies
IPD for EL drive
MIP803 / 804/806 MIP82 * (Investment ratio 50% or more) (Note) Other local companies

MIP5 **
IPD for lamp / power supply
MIP7 ** No contractual restrictions No contractual restrictions
IPD for EL drive
MIP805

(Note) Regarding the sale of MIP10 *, MIP11 *, MIP803 / 804/805, MIP811 / 812, MIP814 to 816, MIP82 *
It can be handled with the prior approval of Power Integrations.
● For sales, please contact the Sales Headquarters of Matsushita Electric Industrial Co., Ltd./Semiconductor Company.

1-1-30 Shibadaimon, Minato-ku, Tokyo 105-8586 (National Building No. 6) TEL (03) 3459-9270