Scribd
Upload
583 views4 pages

Indian Burner Sequence Controller

Energy Combustion, based in Ahmedabad, manufactures and supplies Indian burner controllers, including oil, gas, and dual fuel burner sequence controllers since 1996. Their controllers feature safety mechanisms, including fuse protection, and are designed for easy operation with clear indicators for various functions. The controllers utilize flame sensing through either ionization probes or ultraviolet cells and include a reset option for lockout situations.

Uploaded by

rajesh kothari
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
583 views4 pages

Indian Burner Sequence Controller

Energy Combustion, based in Ahmedabad, manufactures and supplies Indian burner controllers, including oil, gas, and dual fuel burner sequence controllers since 1996. Their controllers feature safety mechanisms, including fuse protection, and are designed for easy operation with clear indicators for various functions. The controllers utilize flame sensing through either ionization probes or ultraviolet cells and include a reset option for lockout situations.

Uploaded by

rajesh kothari
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

“ENERGY COMBUSTION” Ahmedabad largest manufacturer, suppliers and exporters of

INDIAN BURNER CONTROLLER, We are mfg Burner sequence controllers, temp meter,
flame amplifier, flame relay, ultraviolet cell (UV CELL) etc since 1996.

Our Burner Controller is 100% working instead of IMPORTED Burner Controller.


We have two types of model. One is Panel Mounted and other is Burner Mounted.

We are mfg

• OIL BURNER SEQUENCE CONTROLLER


• GAS BURENR SEQUENCE CONTROLLER
• DUEL FUEL BURNER SEQUENCE CONTROLLER

SUPPLY VOLTAGE: - 230 V AND 110 V

All indication like power on , ignition on , solenoid valve on , flame on available in front
of burner controller, for safety we provide fuse if any problem or component problem
blow the fuse and save controller. All connector made by brass.

Here we show our controller image and technical details.

1. PANEL MOUNTED BURENR SEQUENCE CONTROLLER


2. BURNER MOUNTED CONTROLLER

Two types of controller available, flame sensing via

• FLAME ROD ( IONIZATION PROBE)


• ULTRAVIOLET CELL ( UV CELL)

In all model front design is excellent with all indication are available for which function
start or stop.

For safety purpose fuse link available before power supply.

Burner controller reset option available in front of controller.

Back side of controller wiring terminal equipped with BRASS connector.


WORKING OF CONTROLLER

• Before start of the power Pl check all electrical connection.


• When we start supply power indication light on and Burner Blower motor start.
• Then start Pre-purging time its nearest 5-6 sec, after this start purging time and
start ignition,(Pre-purging and purging time adjustable as per customer
requirement at our workshop.) we set standard time as per imported Burner
Sequence Controller.
• Then start supply of Solenoid valve and release the fuel (GAS / OIL), and establish
flame.
• Then start function of Flame Sensing Devices (Ionization probe / Ultraviolet cell-UV
CELL),flame sensing devices sense flame and give feedback to controller, if signal
is ok then controller stop supply of ignition and burner runs continues.
• Received indication of flame in front of controller, if any problem in flame or flame
sensing device flame indicating light blinking or off then controller goes to lock out
mode and give supply for alarm. At that time controller stop the supply of solenoid
valve.
• For lock out reset button available in front of controller. Once u push the reset
button controller start again, if received again lock out indication Pl off power and
check flame sensing device or flame condition its proven or not.
• First clean Ionization Probe or Ultraviolet cell, if continue face problem of flame
sensing then replace the sensing device. Before replacing pl check flame is
establish or not, if not check Gas Solenoid Valve or Gas / Oil pressure.
• Adjust Gas-Oil / Air pressure.

You might also like