TDA7268
2 x 2W STEREO AUDIO AMPLIFIER
WIDE OPERATING RANGE FROM 4.5V TO 18V POUT = 2W @ THD 10% 12V/8 INTERNAL FIXED GAIN 32dB NO FEEDBACK CAPACITOR NO BOUCHEROT CELL THERMAL PROTECTION AC SHORT CIRCUIT PROTECTION SVR CAPACITOR FOR BETTER RIPPLE REJECTION LOW TURN-ON/OFF POP VERY FEW EXTERNAL COMPONENTS STAND-BY MODE (IST-BY < 300A) DESCRIPTION The device TDA7268 is a new technology stereo Audio Amplifier in DIP package specially deBLOCK DIAGRAM
POWERDIP (8+8)
ORDERING NUMBER: TDA7268
signed for TV application. Thanks to the fully complementary output configuration the device delivers a rail to rail voltage swing without need of boostrap capacitor.
IN1
bs
let o
Pr e
du o
IN2 5
(s) ct
so Ob + -
te le
1 VS1 2
ro P
uc d
s) t(
OUT1
VS2
+ -
OUT2
SVR
6 S-GND
916 P-GND
D94AU167B
September 2003
1/6
TDA7268
ABSOLUTE MAXIMUM RATINGS
Symbol VS IO Top Tj Tstg Operating Supply Voltage Output Peak Current Operating Temperature Range Junction Temperature Storage Temperature Range Parameter Value 18 1.5 0 to 70 150 -40 to 125 Unit V A C C C
PIN CONNECTION
VS1 OUT1 SVR IN1 IN2 S-GND OUT2 VS2 1 2 3 4 5 6 7 8
D94AU164A
16 15 14 13 12 11 10 9
PGND PGND PGND PGND PGND PGND PGND PGND
THERMAL DATA
Symbol Rth j-amb Rth j-case Parameter
Thermal Resistance Junction to ambient (on PCB) Thermal Resistance Junction to case
Rth with "on Board" Square Heat Sink vs. Copper Area
THERMAL RESISTANCE JUNCTION TO AMBIENT(C/W)
54 52 50 48 46 44 42 40 38 36 34 0 2
bs O
let o
Pr e
du o
(s) ct
so Ob -
te le
Max. Max.
ro P
uc d
s) t(
Value 70 15
Unit C/W C/W
Example of heatsink using PC board copper
D98AU830
10
12
ON BOARD HEAT-SINK AREA (sq.cm)
2/6
TDA7268
ELECTRICAL CHARACTERISTICS (Tamb = 25C; VS = 12V; RL = 8; f = 1KHz; unless otherwise specified.)
Symbol VS IS Isb VO AV AV RIN PO THD SVR Parameter Supply Voltage Range Quiescent Current Stand-By Current Quiescent Output Voltage Voltage Gain Voltage Gain Matching Input Impedance Output Power Distortion Supply Voltage Rejection THD = 10% PO = 1W Vrip. = 150mVrms; Frip. = 1KHz RS = 10k RS = 50 Rg = 10K; BW = 20Hz to 20KHz PO = 1W; ISB < 300A THD = 10%; VS = 9V; RL = 4 50 60 50 1.9 100 2 0.1 50 46 4 60 1 80 1.8 8 0.4 Pin 3 shorted to GND 5.5 31 Test Condition Min. 4.5 40 0.15 6 32 Typ. Max. 18 60 0.3 6.5 33 1.0 Unit V mA mA V dB dB K W % dB dB V
40
en CT Vsb Asb PO
Total Input Noise Voltage Cross Talk Stand-By Enable Voltage Stand-By Attenution Output Power
bs O
let o
Pr e
du o
(s) ct
so Ob -
eP let
od r
uc
s) t(
V W
dB dB
3/6
TDA7268
Fig. 1: Standard Test and Application Circuit
VS1 C4 100F
VS=12V
IN1 R1 10K
C1 0.1F IN1
+ -
OUT1 C5 470F 8
VS2
IN2 R2 10K
C2 0.1F IN2
+ -
OUT2
C6 470F
SVR S1 STAND-BY
C3 47F S-GND
916 P-GND
D94AU168D
Note: Add R1 & R2 on demoboard only for DC tests.
Fig. 2: PCB And Components Layout Of The Application Circuit of Figure 1
bs O
let o
Pr e
du o
(s) ct
so Ob -
te le
ro P
uc d
s) t(
APPLICATION HINTS: For 12V supply and 8 speaker application, its maximum power dissipation is about 2W. Assumming that max ambient temperature is 70C. Required thermal resistance of the device and heat dissipating means must be equal to (150
4/6
- 70)/2 = 40C/W. Junction to pin thermal resistance of the package is about 15C/W. That means external heat sink of about 25C/W is required. Stand-By switches must be able to discharge Csvr current.
TDA7268
mm MIN. a1 B b b1 D E e e3 F I L Z 3.30 1.27 8.80 2.54 17.78 7.10 5.10 0.130 0.050 0.38 0.51 0.85 0.50 0.50 20.0 0.346 0.100 0.700 0.280 0.201 0.015 1.40 TYP. MAX. MIN. 0.020 0.033 0.020 0.020 0.787 0.055 inch TYP. MAX.
DIM.
OUTLINE AND MECHANICAL DATA
Powerdip 16
bs O
let o
Pr e
du o
(s) ct
so Ob -
te le
ro P
uc d
s) t(
5/6
TDA7268
bs O
let o
Pr e
du o
(s) ct
so Ob -
te le
ro P
uc d
s) t(
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners 2003 STMicroelectronics - All rights reserved STMicroelectronics GROUP OF COMPANIES Australia Belgium - Brazil - Canada - China Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States www.st.com
6/6
