AIR CONDITIONER INSTALLATION MANUAL

Wall Mounted Type PART No. 9320456023-02

Contents
1. SAFETY PRECAUTIONS .................................................................. 1
2. ABOUT THIS PRODUCT................................................................... 3
3. GENERAL SPECIFICATION ............................................................. 4
4. ELECTRICAL REQUIREMENT ......................................................... 4
5. SELECTING THE MOUNTING POSITION ....................................... 4
6. INSTALLATION WORK ..................................................................... 4
7. ELECTRICAL WIRING ..................................................................... 7
8. FINISHING ........................................................................................ 8
9. FRONT PANEL REMOVAL AND INSTALLATION ............................. 8
10. TEST RUN ......................................................................................... 8

R32 11. REMOTE CONTROLLER INSTALLATION........................................ 9

12. OPTIONAL KIT INSTALLATION ....................................................... 9

R32.
13. INSTALLATION WORK ..................................................................... 9
14. SELECTING THE REMOTE CONTROLLER CUSTOM CODE ...... 10
15. FUNCTION SETTING...................................................................... 10
For authorized service personnel only. 16. CUSTOMER GUIDANCE ................................................................ 12
17. ERROR CODES .............................................................................. 12
1. SAFETY PRECAUTIONS
CAUTION
• Be sure to read this Manual thoroughly before installation.
• The warnings and precautions indicated in this Manual contain important information • When moving or relocating the air conditioner, consult experienced service technicians
pertaining to your safety. Be sure to observe them. for disconnection and reinstallation of the unit.
• Hand this Manual, together with the Operating Manual, to the customer. Request the • Do not place any other electrical products or household belongings under indoor unit
customer to keep them on hand for future use, such as for relocating or repairing the or outdoor unit. Condensation dripping from the unit might get them wet, and may
unit.
cause damage or malfunction of your property.
Indicates a potentially or imminently hazardous situation • Be careful not to scratch the air conditioner when handling it.
WARNING which, if not avoided, could result in death or serious injury. • After installation, explain correct operation to the customer, using the operating manual.

Indicates a potentially hazardous situation that may result in Precautions for using R32 refrigerant
CAUTION minor or moderate injury or damage to property.
The basic installation work procedures are the same as conventional refrigerant (R410A,
R22) models.
WARNING However, pay careful attention to the following points:
• The appliance shall be installed, operated and stored in a room with a floor area larger Since the working pressure is 1.6 times higher than that of refrigerant R22 models,
than 2.06 m2. some of the piping and installation and service tools are special. (See “2.1. Special
• Installation of this product must be done by experienced service technicians or profes- tools for R32 (R410A)”.)
sional installers only in accordance with this manual. Installation by non-professional Especially, when replacing a refrigerant R22 model with a new refrigerant R32 model,
or improper installation of the product might cause serious accidents such as injury,
always replace the conventional piping and flare nuts with the R32 and R410A piping and
water leakage, electric shock, or fire. If the product is installed in disregard of the
instructions in this manual, it will void the manufacturer’s warranty. flare nuts on the outdoor unit side.
• Do not turn on the power until all work has been completed. Turning on the power For R32 and R410A, the same flare nut on the outdoor unit side and pipe can be used.
before the work is completed can cause serious accidents such as an electric shock Models that use refrigerant R32 and R410A have a different charging port thread diam-
or a fire.
eter to prevent erroneous charging with refrigerant R22 and for safety. Therefore, check
• If refrigerant leaks when you are working, ventilate the area. If the leaking refrigerant
is exposed to a direct flame, it may produce a toxic gas. beforehand. [The charging port thread diameter for R32 and R410A is 1/2-20 UNF.]
• Installation must be performed in accordance with regulations, codes, or standards for Be more careful than R22 so that foreign matter (oil, water, etc.) does not enter the
electrical wiring and equipment in each country, region, or the installation place. piping. Also, when storing the piping ,securely seal the opening by pinching, taping, etc.
• Do not use means to accelerate the defrosting process or to clean, other than those
(Handling of R32 is similar to R410A.)
recommended by the manufacturer.
• The appliance shall be stored in a room without continuously operating ignition
sources (for example: open flames, an operating gas appliance or an operating
electric heater. CAUTION
• Do not pierce or burn.
• Be aware that refrigerants may not contain an odour. 1-Installation (Space)
• This appliance is not intended for use by persons (including children) with reduced • That the installation of pipe-work shall be kept to a minimum.
physical, sensory or mental capabilities, or lack of experience and knowledge, unless • That pipe-work shall be protected from physical damage.
they have been given supervision or instruction concerning use of the appliance by a • The appliance shall not be installed in an unventilated space, if that space is smaller
person responsible for their safety. Children should be supervised to ensure that they than 2.06 m2.
do not play with the appliance. • That compliance with national gas regulations shall be observed.
• That mechanical connections shall be accessible for maintenance purposes.
• In cases that require mechanical ventilation, ventilation openings shall be kept clear
CAUTION of obstruction.
• When disposing of the product is used, be based on national regulations, properly
• Read carefully all of safety information written in this manual before you install or use
the air conditioner. processed.
• Install the unit by following local codes and regulations in force at the place of installa-
2-Servicing
tion, and the instructions provided by the manufacturer.
• This unit is part of a set constituting an air conditioner. The unit must not be installed 2-1 Service personnel
alone or be installed with non-authorized device by the manufacturer. • Any person who is involved with working on or breaking into a refrigerant circuit
• Always use a separate power supply line protected by a circuit breaker operating on all should hold a current valid certificate from an industry-accredited assessment
wires with a distance between contact of 3 mm for this unit. authority, which authorises their competence to handle refrigerants safely in accor-
• To protect the persons, earth (ground) the unit correctly, and use the power cable dance with an industry recognised assessment specification.
combined with an Earth Leakage Circuit Breaker (ELCB). • Servicing shall only be performed as recommended by the equipment manufacturer.
• The units are not explosion proof, and therefore should not be installed in explosive Maintenance and repair requiring the assistance of other skilled personnel shall be
atmosphere.
carried out under the supervision of the person competent in the use of flammable
• To avoid getting an electric shock, never touch the electrical components soon after
the power supply has been turned off. After turning off the power, always wait 5 min- refrigerants.
utes or more before you touch the electrical components. • Servicing shall be performed only as recommended by the manufacturer.
• This unit contains no user-serviceable parts. Always consult experienced service
technicians for reparing.

En-1

9320456023-02_IM_EN.indd 1 10/6/2017 4:32:09 PM

 CAUTION CAUTION
2-2 Work 3-Repairs to sealed components
• Prior to beginning work on systems containing flammable refrigerants, safety checks • During repairs to sealed components, all electrical supplies shall be disconnected
are necessary to ensure that the risk of ignition is minimized. For repair to the refrig- from the equipment being worked upon prior to any removal of sealed covers, etc.
erating system, the precautions in 2-2 to 2-8 shall be complied with prior to conduct- • If it is absolutely necessary to have an electrical supply to equipment during servic-
ing work on the system. ing, then a permanently operating form of leak detection shall be located at the most
• Work shall be undertaken under a controlled procedure so as to minimize the risk of critical point to warn of a potentially hazardous situation.
a flammable gas or vapour being present while the work is being performed. • Particular attention shall be paid to the following to ensure that by working on electri-
• All maintenance staff and others working in the local area shall be instructed on the cal components, the casing is not altered in such a way that the level of protection is
nature of work being carried out. affected.
• Work in confined spaces shall be avoided. • This shall include damage to cables, excessive number of connections, terminals not
• The area around the workspace shall be sectioned off. made to original specification, damage to seals, incorrect fitting of glands, etc.
• Ensure that the conditions within the area have been made safe by control of flam- • Ensure that apparatus is mounted securely.
mable material. • Ensure that seals or sealing materials have not degraded such that they no longer
serve the purpose of preventing the ingress of flammable atmospheres.
2-3 Checking for presence of refrigerant • Replacement parts shall be in accordance with the manufacturer’s specifications.
• The area shall be checked with an appropriate refrigerant detector prior to and during
work, to ensure the technician is aware of potentially flammable atmospheres. NOTE: The use of silicon sealant may inhibit the effectiveness of some types of leak
• Ensure that the leak detection equipment being used is suitable for use with flam- detection equipment.
mable refrigerants, i.e. nonsparking, adequately sealed or intrinsically safe. Intrinsically safe components do not have to be isolated prior to working on
them.
2-4 Presence of fire extinguisher
• If any hot work is to be conducted on the refrigeration equipment or any associated 4-Repair to intrinsically safe components
parts, appropriate fire extinguishing equipment shall be available at hand. • Do not apply any permanent inductive or capacitance loads to the circuit without
• Have a dry powder or CO2 fire extinguisher adjacent to the charging area. ensuring that this will not exceed the permissible voltage and current permitted for
the equipment in use.
2-5 No ignition sources • Intrinsically safe components are the only types that can be worked on while live in
• No person carrying out work in relation to a refrigeration system which involves the presence of a flammable atmosphere.
exposing any pipe work that contains or has contained flammable refrigerant shall • The test apparatus shall be at the correct rating.
use any sources of ignition in such a manner that it may lead to the risk of fire or • Replace components only with parts specified by the manufacturer.
explosion. • Other parts may result in the ignition of refrigerant in the atmosphere from a leak.
• All possible ignition sources, including cigarette smoking, should be kept sufficiently
far away from the site of installation, repairing, removing and disposal, during which 5-Cabling
flammable refrigerant can possibly be released to the surrounding space. • Check that cabling will not be subject to wear, corrosion, excessive pressure, vibra-
• Prior to work taking place, the area around the equipment is to be surveyed to make tion, sharp edges or any other adverse environmental effects.
sure that there are no flammable hazards or ignition risks. “No Smoking” signs shall • The check shall also take into account the effects of aging or continual vibration from
be displayed. sources such as compressors or fans.

2-6 Ventilated area 6-Detection of flammable refrigerants

• Ensure that the area is in the open or that it is adequately ventilated before breaking • Under no circumstances shall potential sources of ignition be used in the searching
into the system or conducting any hot work. for or detection of refrigerant leaks.
• A degree of ventilation shall continue during the period that the work is carried out. • A halide torch (or any other detector using a naked flame) shall not be used.
• The ventilation should safely disperse any released refrigerant and preferably expel 7-Leak detection methods
it externally into the atmosphere. • Electronic leak detectors shall be used to detect flammable refrigerants, but the
2-7 Checks to the refrigeration equipment sensitivity may not be adequate, or may need re-calibration. (Detection equipment
• Where electrical components are being changed, they shall be fit for the purpose shall be calibrated in a refrigerant-free area.)
and to the correct specification. • Ensure that the detector is not a potential source of ignition and is suitable for the
• At all times the manufacturer’s maintenance and service guidelines shall be followed. refrigerant used.
• If in doubt consult the manufacturer’s technical department for assistance. • Leak detection equipment shall be set at a percentage of the LFL of the refrigerant
• The following checks shall be applied to installations using flammable refrigerants. and shall be calibrated to the refrigerant employed and the appropriate percentage of
- The charge size is in accordance with the room size within which the refrigerant gas (25 % maximum) is confirmed.
containing parts are installed. • Leak detection fluids are suitable for use with most refrigerants but the use of
- The ventilation machinery and outlets are operating adequately and are not detergents containing chlorine shall be avoided as the chlorine may react with the
obstructed. refrigerant and corrode the copper pipe-work.
- If an indirect refrigerating circuit is being used, the secondary circuit shall be • If a leak is suspected, all naked flames shall be removed/extinguished.
checked for the presence of refrigerant. • If a leakage of refrigerant is found which requires brazing, all of the refrigerant shall
- Marking to the equipment continues to be visible and legible. Markings and signs be recovered from the system, or isolated (by means of shut off valves) in a part of
that are illegible shall be corrected. the system remote from the leak.
- Refrigeration pipe or components are installed in a position where they are unlikely Oxygen free nitrogen (OFN) shall then be purged through the system both before
to be exposed to any substance which may corrode refrigerant containing compo- and during the brazing process.
nents, unless the components are constructed of materials which are inherently 8-Removal and evacuation
resistant to being corroded or are suitably protected against being so corroded. • When breaking into the refrigerant circuit to make repairs – or for any other
2-8 Checks to electrical devices purpose –conventional procedures shall be used.
• Repair and maintenance to electrical components shall include initial safety checks However, it is important that best practice is followed since flammability is a consid-
and component inspection procedures. eration.
• If a fault exists that could compromise safety, then no electrical supply shall be con- The following procedure shall be adhered to:
nected to the circuit until it is satisfactorily dealt with. • remove refrigerant
• If the fault cannot be corrected immediately but it is necessary to continue operation, • purge the circuit with inert gas
an adequate temporary solution shall be used. • evacuate
• This shall be reported to the owner of the equipment so all parties are advised. • purge again with inert gas
• Initial safety checks shall include. • open the circuit by cutting or brazing
- That capacitors are discharged: this shall be done in a safe manner to avoid pos- • The refrigerant charge shall be recovered into the correct recovery cylinders.
sibility of sparking. • The system shall be “flushed” with OFN to render the unit safe.
- That there no live electrical components and wiring are exposed while charging, • This process may need to be repeated several times.
recovering or purging the system. • Compressed air or oxygen shall not be used for this task.
- That there is continuity of earth bonding. • Flushing shall be achieved by breaking the vacuum in the system with OFN and
continuing to fill until the working pressure is achieved, then venting to atmosphere,
and finally pulling down to a vacuum.
• This process shall be repeated until no refrigerant is within the system.
• When the final OFN charge is used, the system shall be vented down to atmospheric
pressure to enable work to take place.
• This operation is absolutely vital if brazing operations on the pipe work are to take
place.
• Ensure that the outlet for the vacuum pump is not close to any ignition sources and
there is ventilation available.

En-2

9320456023-02_IM_EN.indd 2 10/6/2017 4:32:09 PM

 Explanation of symbols displayed on the indoor unit or outdoor unit.
CAUTION
This symbol shows that this appliance uses a flammable
9-Charging procedures refrigerant.
• In addition to conventional charging procedures, the following requirements shall be
WARNING
If the refrigerant is leaked and exposed to an external igni-
followed. tion source, there is a risk of fire.
- Ensure that contamination of different refrigerants does not occur when using
This symbol shows that the operation manual should be
charging equipment. CAUTION read carefully.
Hoses or lines shall be as short as possible to minimize the amount of refrigerant
contained in them. This symbol shows that a service personnel should be
- Cylinders shall be kept upright. CAUTION handling this equipment with reference to the installation
- Ensure that the refrigeration system is earthed prior to charging the system with manual.
refrigerant.
This symbol shows that information is available such as
- Label the system when charging is complete (if not already). CAUTION the operating manual or installation manual.
- Extreme care shall be taken not to overfill the refrigeration system.
• Prior to recharging the system it shall be pressure tested with OFN.
• The system shall be leak tested on completion of charging but prior to commission-
ing. 2. ABOUT THIS PRODUCT
• A follow up leak test shall be carried out prior to leaving the site.

10-Decommissioning
• Before carrying out this procedure, it is essential that the technician is completely
2.1. Special tools for R32 (R410A)
familiar with the equipment and all its details.
• It is recommended good practice that all refrigerants are recovered safely. Tool name Change from R22 to R32 (R410A)
• Prior to the task being carried out, an oil and refrigerant sample shall be taken in
case analysis is required prior to re-use of reclaimed refrigerant. Pressure is high and cannot be measured with a R22
• It is essential that electrical power is available before the task is commenced. gauge. To prevent erroneous mixing of other refrigerants,
a) Become familiar with the equipment and its operation. Gauge manifold the diameter of each port has been changed.
It is recommended to use gauge with seals -0.1 to 5.3 MPa
b) Isolate system electrically.
(-1 to 53 bar) for high pressure.
c) Before attempting the procedure ensure that:
-0.1 to 3.8 MPa (-1 to 38 bar) for low pressure.
• mechanical handling equipment is available, if required, for handling refriger-
ant cylinders; To increase pressure resistance, the hose material and base
Charge hose
• all personal protective equipment is available and being used correctly; size were changed. (R32/R410A)
• the recovery process is supervised at all times by a competent person;
A conventional vacuum pump can be used by installing a
• recovery equipment and cylinders conform to the appropriate standards. Vacuum pump vacuum pump adapter.
d) Pump down refrigerant system, if possible. (Use of a vacuum pump with a series motor is prohibited.)
e) If a vacuum is not possible, make a manifold so that refrigerant can be removed
from various parts of the system. Special gas leakage detector for HFC refrigerant R410A or
Gas leakage detector
f) Make sure that cylinder is situated on the scales before recovery takes place. R32.
g) Start the recovery machine and operate in accordance with manufacturer’s Copper pipes
instructions. It is necessary to use seamless copper pipes and it is desirable that the amount of residual
h) Do not overfill cylinders. (No more than 80 % volume liquid charge). oil is less than 40 mg/10 m. Do not use copper pipes having a collapsed, deformed or
i) Do not exceed the maximum working pressure of the cylinder, even temporarily. discolored portion (especially on the interior surface). Otherwise, the expansion value or
j) When the cylinders have been filled correctly and the process completed, make capillary tube may become blocked with contaminants.
sure that the cylinders and the equipment are removed from site promptly and all As an air conditioner using R32 (R410A) incurs pressure higher than when using R22, it is
isolation valves on the equipment are closed off. necessary to choose adequate materials.
k) Recovered refrigerant shall not be charged into another refrigeration system un-
less it has been cleaned and checked. WARNING
11-Labelling • Do not use the existing (for R22) piping and flare nuts.
• Equipment shall be labelled stating that it has been de-commissioned and emptied If the existing materials are used, the pressure inside the refrigerant cycle will rise and
of refrigerant. cause failure, injury, etc. (Use the special R32/R410A materials.)
• The label shall be dated and signed. • Use (refill or replace with) specified refrigerant (R32) only. Use of unspecified refriger-
• Ensure that there are labels on the equipment stating the equipment contains flam- ant can cause product malfunction, burst, or injury.
mable refrigerant. • Do not mix any gas or impurities except specified refrigerant (R32). Inflow of air or ap-
plication of unspecified material makes the internal pressure of the refrigerant cycle too
12-Recovery
high, and may cause product malfunction, burst of piping, or injury.
• When removing refrigerant from a system, either for servicing or decommissioning, it
is recommended good practice that all refrigerants are removed safely.
• When transferring refrigerant into cylinders, ensure that only appropriate refrigerant
WARNING
recovery cylinders are employed.
• Ensure that the correct number of cylinders for holding the total system charge are • For appropriate working of the air conditioner, install it as written in this manual.
available. • To connect indoor unit and outdoor unit, use air conditioner piping and cables available
• All cylinders to be used are designated for the recovered refrigerant and labelled for through your local distributor. This manual describes proper connections using such
that refrigerant (i.e. special cylinders for the recovery of refrigerant). installation set.
• Cylinders shall be complete with pressure relief valve and associated shut-off valves • Do not turn on the power until all work has been completed.
in good working order.
• Empty recovery cylinders are evacuated and, if possible, cooled before recovery
occurs. CAUTION
• The recovery equipment shall be in good working order with a set of instructions
concerning the equipment that is at hand and shall be suitable for the recovery of This manual describes how to install the indoor unit only. To install the outdoor unit, (it
flammable refrigerants. any), refer to the installation manual included in each product.
• In addition, a set of calibrated weighing scales shall be available and in good working
• Be careful not to scratch the air conditioner when handling it.
order.
• After installation, explain correct operation to the customer, using the operating manual.
• Hoses shall be complete with leak-free disconnect couplings and in good condition.
• Before using the recovery machine, check that it is in satisfactory working order, has
been properly maintained and that any associated electrical components are sealed
to prevent ignition in the event of a refrigerant release.
Consult manufacturer if in doubt.
• The recovered refrigerant shall be returned to the refrigerant supplier in the correct
recovery cylinder, and the relevant Waste Transfer Note arranged.
• Do not mix refrigerants in recovery units and especially not in cylinders.
• If compressors or compressor oils are to be removed, ensure that they have been
evacuated to an acceptable level to make certain that flammable refrigerant does not
remain within the lubricant.
• The evacuation process shall be carried out prior to returning the compressor to the
suppliers.
• Only electric heating to the compressor body shall be employed to accelerate this
process.
• When oil is drained from a system, it shall be carried out safely.

En-3

9320456023-02_IM_EN.indd 3 10/6/2017 4:32:09 PM

 2.2. Accessories 3.2. Additional materials required for installation
A. Refrigeration (armored) tape
The following installation accessories are supplied. Use them as required.
B. Insulated staples or clamps for connecting wire (See your local electrical codes.)
Name and Shape Q’ty Name and Shape Q’ty C. Putty
Operating Manual Cloth tape D. Refrigeration lubricant
E. Clamps or saddles to secure refrigerant piping
1 1

Installation Manual Tapping screw 4. ELECTRICAL REQUIREMENT

(This manual) (large)
The indoor unit is powered from the outdoor unit. Do not power indoor unit from separate
1 5
power source.

WARNING
Wall hook bracket Tapping screw
1 (small) 2 Standard for electrical wiring and equipment differs in each country or region. Before you
start electrical working, confirm related regulations, codes, or standards.
Remote controller Air cleaning filter
Cable Conductor size [mm2] Type Remarks
1 2 3 cable + Earth (Ground),
Connection cable 1.5 - 2.5 Type 60245 IEC 57
1 Ø 240 V
Max. Cable Length: Limit voltage drop to less than 2%. Increase cable gauge if voltage
Battery Filter holders
drop is 2% or more.
2 2

Remote controller holder Seal A

5. SELECTING THE MOUNTING POSITION
Decide the mounting position with the customer as follows:
1 1
5.1. Indoor unit
(1) Install the indoor unit level on a strong wall which is not subject to vibration.
(2) The inlet and outlet ports should not be obstructed : the air should be able to blow all
The following items are necessary to install this air conditioner. (The items are not includ- over the room.
ed with the air conditioner and must be purchased separately.) (3) Install the unit a dedicated electrical branch circuit.
Name Q’ty Name Q’ty (4) Do not install the unit where it will be exposed to direct sunlight.
(5) Install the unit where connection to the outdoor unit is easy.
Connection pipe assembly 1 Wall cap 1
(6) Install the unit where the drain pipe can be easily installed.
Connection cable (4-conductor) 1 Saddle 1 set (7) Take servicing, etc. into consideration and leave the spaces shown in “6.1. Installation
Wall pipe 1 Drain hose 1 dimensions”. Also install the unit where the filter can be removed.
Decorative tape 1 Tapping screws 1 set Correct initial installation location is important because it is difficult to move the unit after it
Vinyl tape 1 Sealant 1 is installed.

WARNING
2.3. Optional parts Install the unit where is capable to support the weight of the unit. Secure the unit firmly
so that the unit does not topple or fall.
Refer to each installation manual for the method of installing optional parts.
Parts name Model name Application
CAUTION
Wired Remote Controller * UTY-RVNYN For air conditioner operation
Wired Remote Controller * UTY-RNNYN For air conditioner operation Do not install the unit in the following areas:
Simple Remote Controller * UTY-RSNYN For air conditioner operation • Area with high salt content, such as at the seaside. It will deteriorate metal parts, caus-
External connect kit * UTY-XWZXZ5 For control input/output port ing the parts to fail or the unit to leak water.
Communication kit UTY-TWBXF1 For the installation of optional parts • Area filled with mineral oil or containing a large amount of splashed oil or steam. It will
* Optional communication kit is necessary for the installation. deteriorate plastic parts, causing the parts to fail or the unit to leak water.
• Area where is close to heat sources.
• Area that generates substances that adversely affect the equipment, such as sulfuric
gas, chlorine gas, acid, or alkali. It will cause the copper pipes and brazed joints to cor-
3. GENERAL SPECIFICATION rode, which can cause refrigerant leakage.
• Area that can cause combustible gas to leak, contains suspended carbon fibers or
This INSTALLATION MANUAL briefly outlines where and how to install the air conditioning system. flammable dust, or volatile in flammables such as paint thinner or gasoline.
Please read over the entire set of instructions for the indoor and outdoor units and make sure all • If gas leaks and settles around the unit, it can cause a fire.
accessory parts listed are with the system before beginning. • Area where animals may urinate on the unit or ammonia may be generated.

3.1. Type of copper pipe and insulation material • Do not use for preservation of food, plants, animals, precision equipment, art work, or
other objects. This may cause quality deterioration of those items.
• Install the unit where drainage does not cause any trouble.
CAUTION • Install the indoor unit, outdoor unit, power supply cable, transmission cable, and re-
mote control cable at least 1 m away from a television or radio receivers. The purpose
For appropriate pipe length and height difference, refer to the installation manual for the of this is to prevent TV reception interference or radio noise.
outdoor unit. (Even if they are installed more than 1 m apart, you could still receive noise under
some signal conditions.)
• If children may approach the unit, take preventive measures so that they cannot reach
Gas pipe size (thickness) [mm] Liquid pipe size (thickness) [mm] the unit.
Ø 12.70 (0.8) Ø 6.35 (0.8) • Install the indoor unit on the wall where the height from the floor is more than 1.8 m.

CAUTION
6. INSTALLATION WORK
• Wrap heat insulation around both of the gas pipe and the liquid pipe.
No heat-insulation work or incorrect heat-insulation work may cause water leaks.
• In a reverse cycle model, use heat insulation with heat resistance above 120 °C. WARNING
• If expected humidity of the installation location of refrigerant pipes is higher than 70
During transportation or relocation of the indoor unit, pipes shall be covered with the
%, wrap the heat insulation around the refrigerant pipes.
wall hook bracket for protection. Do not move the appliance by holding the indoor unit
If the expected humidity is between 70 % and 80 %, use heat insulation that has
thickness of 15 mm or more. pipes.
If the expected humidity is higher than 80 %, use heat insulation that has thickness (The stress applied to the pipe joints may cause the flammable gas to leak during
of 20 mm or more. operation.)
• Using of thinner heat insulation than specified above may cause a condensation on
the surface of the insulation. CAUTION
• Use heat insulation with thermal conductivity of 0.045 W/(m•K) or less, at 20 °C.
• Do not hit or push the human sensor. This may lead to damage or malfunction.
• Do not touch the human sensor. Any scratches or dirt may lead to incorrect detection.
• Do not place large objects near the human sensor. Also keep heating units outside the
sensor’s detection area.

En-4

9320456023-02_IM_EN.indd 4 10/6/2017 4:32:10 PM

 Detection range of the human sensor is as follows. (1) Install the wall hook bracket so that it is correctly positioned horizontally and vertically.
Vertical angle 90° (Side view) Horizontal angle 100° (Top view) If the wall hook bracket is titled, water will drip to the floor.
(2) Install the wall hook bracket so that it is strong enough to support the weight of the unit.
• Fasten the wall hook bracket to the wall with 5 or more screws through the holes near
7m the outer edge of the bracket.
7m 90° • Check that there is no rattle at the wall hook bracket.
50° 50° Wall hook bracket

6.1. Installation dimensions

Wall hook
bracket 84 mm
or over 133 mm or over
127 mm or over

Tapping screws
(large, accessories)

CAUTION
1.5 m or over 1.8 m
or over
(Wall cap) Install the wall-hook bracket both horizontally and vertically aligned.
Misaligned installation may cause water leakage.
Remote Remote controller
controller holder The flare connection
Tapping screws
part should be installed
outdoors.
6.5. Forming the drain hose and pipe
(small, accessories)
[Rear piping, Right piping, Bottom piping]
• Install the indoor unit piping in the direction of the wall hole and bind the drain hose
and pipe together with vinyl tape.
• Install the piping so that the drain hose is at the bottom.
• Wrap the pipes of the indoor unit that are visible from the outside with decorative tape.
6.2. Indoor unit piping direction
[For Left rear piping (Drain hose), Left piping (Drain hose)]
The piping can be connected in the 3 directions indicated in the following. Interchange the drain cap and the drain hose.
When the piping is connected to direction (2) or (3) , cut along the piping groove on the
side of the front cover with a hacksaw.
CAUTION
(Rear) • Insert drain hose and drain cap securely. Drain should slope down to avoid water leakage.
• When inserting the drain hose, no other material than water should be applied.
Application of other material than water will cause deterioration of the hose, and may
cause water leakage.
(2) Right • After you remove a drain hose, be sure to attach the drain cap.
outlet (1) Rear outlet
• When you secure the piping and drain hose with tape, arrange the drain hose so that
it is at the bottom of the piping.
(3) Bottom outlet
• For drain hose piping in low temperature environment, you need to apply freeze
protection to prevent a frozen drain hose.
After cooling operation is performed in low temperature environment, (when outdoor
6.3. Cutting the hole in the wall for the connecting piping temperature under 0 °C,) water in the drain hose could be frozen. Frozen drain water
will block the water flow in the hose, and may cause water leakage at the indoor unit.
(1) Cut a 65 mm diameter hole in the wall at the position shown in the following.
(2) Cut the hole so that the outside end is lower (5 to 10 mm) than the inside end. Installing the Drain cap
(3) Always align the center of the wall hole. If misaligned, water leakage will occur. Use a hexagonal wrench 4 mm at opposite side to
(4) Cut the wall pipe to match the wall thickness, stick it into the wall cap, fasten the cap with insert the drain cap, till the drain cap contacts the tip No gap
vinyl tape, and stick the pipe through the hole. of the drain cock.
(5) Cut the hole a little lower so that drain water will flow freely.
Wall hook bracket Center mark
Drain
Hexagonal cock
Drain cap
wrench

Right piping
Fasten with 65 mm dia. hole Bind with vinyl tape
vinyl tape Refrigerant pipes (top)
5 to 10 mm low
Rear piping

Wall pipe* Indoor unit drain hose (bottom)

Bottom piping
Wall cap* (Inside) (Outside)
Wall *Locally purchased
For left outlet piping
(Drain hose), cut off
WARNING the piping outlet cutting
groove with a hacksaw.
Always use the wall pipe. If the wall pipe is not used, the cable that is connected between
the indoor unit and the outdoor unit may touch metal, and cause an electric discharge.

6.4. Installing the wall hook bracket

Drain cap
Remove the drain cap by pull-
Indoor unit ing at the projection at the end
drain hose of the cap with pliers, etc.

• Remove the wall hook bracket from the indoor unit. (Remove screw).

En-5

9320456023-02_IM_EN.indd 5 10/6/2017 4:32:10 PM

 Removing the drain hose Installing the drain hose Dimension A [mm]
Remove the screw at the left of Vertically insert the drain hose toward the Pipe outside diameter
Flare tool for R32, Dimension B [mm]
drain hose and pull out drain hose. inside, so that the drain fixture (white) can ac- [mm (in.)]
clutch type
curately align with the screw hole around the
6.35 (1/4) 9.1
drain cock.
After inserting and before replacing, please 9.52 (3/8) 13.2
reinstall and fix the removed screws. 12.70 (1/2) 0 to 0.5 16.6
Screw Drain hose Drain cock 15.88 (5/8) 19.7
Screw hole Screw 19.05 (3/4) 24.0

When using conventional flare tools to flare R32 pipes, the dimension A should be approx-
imately 0.5 mm more than indicated in the table (for flaring with R32 flare tools) to achieve
the specified flaring. Use a thickness gauge to measure the dimension A.
Drain fixture Drain hose
Drain fixture Width across Width across flats
flats Pipe outside diameter [mm (in.)]
• Please hold around the joint of the drain hose during work. of Flare nut [mm]
• As the screw is inside, be sure to use screwdrivers treated with magnet. 6.35 (1/4) 17
9.52 (3/8) 22
• After passing the indoor piping and drain hose through the wall hole, hang the indoor unit on 12.70 (1/2) 26
the hooks at the top and bottom of the wall hook bracket.
15.88 (5/8) 29
[Installing the indoor unit] 19.05 (3/4) 36
• Hang the indoor unit from the hooks at the top of the wall hook bracket.
6.6.2. Bending pipes
• Insert the spacer, etc. between the indoor unit and the wall hook bracket and separate
the bottom of the indoor unit from the wall. • The pipes are shaped by your hands. Be careful not to collapse them.
• Bend R70 mm or more with a pipe bender.
Indoor unit • Do not bend the pipes in an angle more than 90°.
• When pipes are repeatedly bend or stretched, the material will harden, making it difficult
to bend or stretch them any more.
(Spacer) • Do not bend or stretch the pipes more than 3 times.

Wall hook bracket CAUTION

To prevent breaking of the pipe, avoid sharp bends.

If the pipe is bent repeatedly at the same place, it will break.

6.6.3. Pipe connection

WARNING
The flare connection shall not be performed indoors.

Indoor unit Wall hook bracket

Top hooks CAUTION
Be sure to Install the pipe against the port on the indoor unit correctly. If the centering
is improper, the flare nut cannot tighten smoothly. If the flare nut is forced to turn, the
threads will be damaged.
Do not remove the flare nut from the indoor unit pipe until immediately before con-
necting the connection pipe.

Bottom hooks Hold the torque wrench at its grip, keeping it in the right angle with the pipe, in order
to tighten the flare nut correctly.
• After hooking the indoor unit to the top hook, hook the fittings of the indoor unit to the 2
bottom hooks while lowering the unit and pushing it against the wall. Tighten the flare nuts with a torque wrench using the specified tightening method.
Otherwise, the flare nuts could break after a prolonged period, causing refrigerant to
leak and generate hazardous gas if the refrigerant comes into contact with a flame.
6.6. Flare connection (Pipe connection)
Connect the piping so that the control box cover can easily be removed for servicing
when necessary.
CAUTION In order to prevent water from leaking into the control box, make sure that the piping
is well insulated.
Tighten the flare nuts with a torque wrench using the specified tightening method.
Otherwise, the flare nuts could break after a prolonged period, causing refrigerant to leak
and generate hazardous gas if the refrigerant comes into contact with a flame. When the flare nut is tightened properly by your hand, hold the body side coupling with a
wrench, then tighten with a torque wrench. (See the table below for the flare nut tightening
6.6.1. Flaring torques.)
Use special pipe cutter and flare tool designed for R410A or R32 pipework.
(1) Cut the connection pipe to the necessary length with a pipe cutter.
(2) Hold the pipe downward so that cuttings will not enter the pipe and remove any burrs. Tighten with 2 wrenches.
(3) Insert the flare nut (always use the flare nut attached to the indoor unit(s) and outdoor unit
or branch box respectively) onto the pipe and perform the flare processing with a flare
Holding wrench
tool. Use the special R410A or R32 flare tool, or the conventional flare tool. Leakage of
refrigerant may result if other flare nuts are used. Flare nut
Torque wrench
(4) Protect the pipes by pinching them or with tape to prevent dust, dirt, or water from
entering the pipes.

Check if [L] is flared uniformly

and is not cracked or scratched. Indoor unit pipe
B Connection pipe
(Body side)

Die
Flare nut [mm (in.)] Tightening torque [N·m (kgf·cm)]
6.35 (1/4) dia. 16 to 18 (160 to 180)
A
9.52 (3/8) dia. 32 to 42 (320 to 420)
L
Pipe 12.70 (1/2) dia. 49 to 61 (490 to 610)
15.88 (5/8) dia. 63 to 75 (630 to 750)
19.05 (3/4) dia. 90 to 110 (900 to 1,100)

En-6

9320456023-02_IM_EN.indd 6 10/6/2017 4:32:11 PM

 7. ELECTRICAL WIRING 7.3. How to connect wiring to the terminals
Caution when wiring cable
CAUTION To strip off the insulation of a lead wire, always use a special tool such as a wire strip-
per. If there is no special tool, carefully strip off the insulation by using a knife or other
Be careful not to generate a spark as follows for using a flammable refrigerant.
utensil.
• Do not remove the fuse while the power is on.
• Do not disconnect the wiring while the power is on. (1) Use ring terminals with insulating sleeves as shown in the figure to connect to the
terminal block.
• It is recommended to position the outlet connection in a high position. Place the
(2) Securely clamp the ring terminals to the wires by using an appropriate tool so that the
cords so that they do not get tangled.
wires do not come loose.
Strip : 10 mm Ring terminal
7.1. Wiring system diagram

WARNING Sleeve
(3) Connect specified wires securely, and fasten them so that there is no stress applied
• Before connecting the wires, make sure the power supply is OFF.
on the terminals.
• Every wire must be connected firmly.
(4) Use a screwdriver with an appropriate bit size to tighten the terminal screws. Using of
• No wire should be allowed to touch refrigerant tubing, the compressor, or any mov-
screwdriver with inappropriate bit size will damage the screw heads, and the screws
ing part.
will not be tightened properly.
• Loose wiring may cause the terminal to overheat or result in unit malfunction. A fire
(5) Do not overtighten the terminal screws. Otherwise, the screws may break.
hazard may also exist. Therefore, be sure all wiring is tightly connected.
• Connect wires to the matching numbers of terminals. Screw with special washer
Screw with special washer

INDOOR UNIT OUTDOOR UNIT Ring terminal

Wire
TERMINAL Power line
Ring terminal

Terminal blocks
Wire
Control line Please connect to the
(6) See the table for the terminal screw tightening torques.
specified terminal.
Earth (Ground) line Tightening torque [N·m (kgf·cm)]
M4 screw 1.2 to 1.8 (12 to 18)

7.2. Indoor unit wiring CAUTION

1. Remove the wire cover. (Remove 1 screw.) • Match the terminal block numbers and connection cable colors with those of the
2. Remove the cable clamp. outdoor unit. Incorrect wiring may cause a fire.
3. Ring terminals connect to the connection cable. • Connect the connection cables firmly to the terminal block. Imperfect installation may
4. Connect the ring terminals fully into the terminal block. cause a fire.
• When fixing the connection cable with the cable clamp, always fasten the cable at the
5. Fasten the connection cable with a cable clamp. plastic jacket portion, but not at the insulator portion. If the insulator is chafed, electric
leakage may occur.
• Always connect the earth (ground) wire. Improper earthing (grounding) work can
cause electric shocks.
Cable clamp Wire cover • Do not use the earth (ground) screw for the indoor unit to the outdoor unit unless it is
60 mm

40 mm

specified.
Screw
Screw

Earth (Ground) wire

Cable clamp Wire cover

Screw
Screw

Insert the wire cover tab into the square hole

Connection cable of the indoor unit and fasten with a screw.

En-7

9320456023-02_IM_EN.indd 7 10/6/2017 4:32:11 PM

 8. FINISHING 9.1. Front panel removal
(1) Insulate between pipes. (1) Remove intake grille (Reference the intake grille removal.)
• Insulate suction and discharge pipes separately. (2) Remove 3 caps.
• For rear, right, and bottom piping, overlap the connection pipe heat insulation and (3) Remove wire cover.
indoor unit pipe heat insulation and bind them with vinyl tape so that there is no gap. (4) Remove 7 screws.
(2) Temporarily fasten the connection cable along the connection pipe with vinyl tape. Screws (Wire cover )
(Wrap to about 1/3 the width of the tape from the bottom of the pipe so that water
does not enter.)
(3) Fasten the connection pipe to the outside wall with a saddle, etc. Wire cover
(4) Fill the gap between the outside wall pipe hole and the pipe with sealer so that rain
water and wind cannot blow in.
(5) Fasten the drain hose to the outside wall, etc.
Outside wall cap*
Saddle*
Sealer putty* Screws ( 7 position )
Diffuser
Caps ( 3 position )
NOTE : When replacing the front panel, do not scratch or damage the diffuser.
(5) The front panel is pulled to the front, raising the upper surface, then the front panel is
(Outdoors)
removed.

Pipe Wall *Locally purchased

Overlap the insulation

Connection pipe
Front panel
(heat insulation)
Indoor unit pipe
Bind the pipes together (heat insulation)
Vinyl tape
so that there is no gap.

Pipe
Wrap with cloth tape
9.2. Front panel installation
Cloth tape
Drain hose (1) First, fit the lower part of the front panel, and insert top and bottom hooks. (3 top
sides, 2 center)

Seal A is used when the diameter Top hooks

of gas pipe is Ø12.70 or more. (3 position)
Top holes (3 position)

Butt connection pipe (heat

insulation) against the indoor
unit pipe (heat insulation) and
wrap with seal A so that there
is no gap. Front panel

Indoor unit
Check the following: PROHIBITED
(2) Attach the 7 screws.
(3) Attach the wire cover.
GOOD Drain hose
(4) Attach the 3 caps.
Saddle
(5) Attach the intake grille.
Lifted up Wave End in water
CAUTION
Install the front panel and intake grille securely. If installation is imperfect, the front
panel or intake grille may fall off and cause injury.
9. FRONT PANEL REMOVAL AND INSTALLATION
Intake grille removal Intake grille installation
Open the intake While holding the 10. TEST RUN
grille. While gently grille horizontal, set
pressing the left the left and right
Check items
and right mounting mounting shafts into
a shafts of the intake the pillow blocks at (1) Is operation of each button on the remote control unit normal?
b (2) Does each lamp light normally?
grille outward “a”, the top of the panel
c (3) Do airflow direction louvers operate normally?
remove the intake “c”.
grille in direction of To latch each shaft (4) Is the drain normal?
the arrow “b”. properly, insert the (5) Do not have an abnormal noise and vibration during operation?
shaft until it snaps. • Do not operate the air conditioner in test run for a long time.
Press 4 places on [Operation method]
the intake grille to
• For the operation method, refer to the operating manual.
close it completely.
• The outdoor unit, may not operate, depending on the room temperature. In this case,
keep on pressing the MANUAL AUTO button of the indoor unit for more than 10
seconds. The OPERATION indicator lamp and TIMER indicator lamp will begin to flash
simultaneously during cooling test run.
Then, heating test run will begin in about 3 minutes when HEAT is selected by the
remote controller operation [reverse cycle model only].
(Please follow the operating manual for remote controller operation.)
• To end test operation, press the remote controller START/STOP button.
(When the air conditioner is running by pressing the test run button, the OPERATION
Lamp and TIMER Lamp will simultaneously flash slowly.)

En-8

9320456023-02_IM_EN.indd 8 10/6/2017 4:32:13 PM

 [Using the wired remote controller] (Option)
For the operation method, refer to the operating manual.
13.INSTALLATION WORK
(1) Stop the air conditioner operation.
(2) Press the MODE button and the FAN button simultaneously for 2 seconds or more to 13.1. Accessories (Communication kit)
start the test run. The following installation accessories are supplied. Use them as required.
Name and Shape Q’ty Description
Relay control board For connecting the
wired remote control
unit and external
Test run display connect wire.
1
(3) Press the START/STOP button to stop the test run.

11. REMOTE CONTROLLER INSTALLATION

Cable tie For fixing the wires
from control box.
Check that the indoor unit correctly receives the signal from the remote controller, then
install the remote controller holder. 1

CAUTION
Do not install the remote controller holder in the following conditions: Relay wire For connecting the
• Any places exposed in direct sunlight relay control board and
• Positions affected by the heat from a stove or heater 1
control unit board.

11.1. Remote controller holder installation Wiring label For displaying the additional
wiring diagram.
1
• Install the remote controller a maximum distance of 7 m from the remote control signal
receiver. After installing the remote controller, check that it operates correctly.
• Install the remote controller holder to a wall, pillar, etc. with the tapping screw.
13.2. Installation work
Remote controller Remote controller
holder fixing mounting
13.2.1. Removing intake grille and front panel
Remote controller (See “9. FRONT PANEL REMOVAL AND INSTALLATION” and “9.1. Front panel removal”)
holder
13.2.2. Removing control cover
(1) Set Screw 1
Tapping
screws Remote
(small, controller
accessories) (2) Down

12.OPTIONAL KIT INSTALLATION Screw 2

This air conditioner can be connected with the following optional kits. Control cover Control box
• Wired remote controller
Remove the screw 1 and 2, then remove the control cover.
• Simple remote controller
• External connect kit
13.2.3. Installing relay control board and relay wire terminal
BEFORE INSTALLING THE WIRED REMOTE CONTROLLER
• When you use wired remote controller, some functions may not be used. Clasp Control unit board

CAUTION
• Before installation, make sure that all power supplies has been disconnected.
Connector (CN2)
• Do not touch the aluminum fins of heat exchanger built-in the indoor or outdoor unit to
avoid personal injury when you install or maintain the unit.
• In the installation or removal, be sure not to have any wires getting caught by parts Relay wire
or getting an extreme tension. Excessive pressure or tension to the wire may cause
malfunction of the air conditioner. Clasps
• Avoid any places exposed in direct sunlight.
• Choose a position that will not be affected by the heat from a stove or heater.
• Before setting up the optional kit, confirm whether the air-conditioner receives the
signal from the remote controller.
Relay control board
• Do not connect the wired remote controller to the terminal for power supply.
• When connecting the wired remote controller with the indoor unit, use the connecting *2. Notice the installing direction
cable that is supplied with wired remote controller or simple remote controller. of the relay control board. (The
Notice *2. elevation of the control box is fit
• Recommended cable length of wired remote controller is 10 m. When you extend the
cable, insulate the connecting part of the cable. Connector (CND01) for the recess of the relay con-
trol board.)
Do not connect power supply with the terminal.
(1) Insert the relay control board toward 2 clasps.
INDOOR UNIT (2) Then set the board with the clasp.
(3) Connect the relay wire terminal to the connector (CND01) on the relay control board.
(4) Connect the relay wire terminal to the connector (CN2) on the control unit board.
PCB
CAUTION
Be careful not to damage the parts on the board.
Otherwise, it will cause malfunction.

TERMINAL

En-9

9320456023-02_IM_EN.indd 9 10/6/2017 4:32:15 PM

 13.2.4. Installing optional kits 14. SELECTING THE REMOTE CONTROLLER CUSTOM CODE
Remote controller cable modification When two or more air conditioners are installed in a room and the remote controller is
operating an air conditioner other than the one you wish to set, change the custom code
(1) Use a tool to cut off the terminal on the end of the remote controller cable, and then
remove the insulation from the cut end of the cable. of the remote controller to operate only the air conditioner you wish to set (4 selections
(2) Connect the remote controller cable and connecting cable. possible).
(Supplied with wired remote controller.) When two or more air conditioners are installed in a room, please contact your retailer to
Important: Be sure to insulate the connection between the cables. set the individual air conditioner custom codes.

Selecting the Remote Controller Custom Code

20 mm

Connector Use the following steps to select the custom code of the remote controller. (Note that the
air conditioner cannot receive a custom code if the air conditioner has not been set for the
White
Red custom code.)
m
m
(1) Press the START/STOP ( ) button until only the clock
30

Remote

m
is displayed on the remote controller display.

5m
controller cable Black
(2) Press the MODE button for at least 5 seconds to display

~4
White

35
the current custom code (initially set to ).
Remote Red

m
Insulated

0m
controller cable connection (3) Press the SET TEMP. ( / ) buttons to change the

16
0~
Black custom code between .
15
Match the code on the display to the air conditioner
custom code.
(4) Press the MODE button again to return to the clock
display. The custom code will be changed.
Installing the wired remote controller terminal (sold separately)
Connect the wired remote controller terminal to the connector (CNC01) on the relay con-
trol board.
Connector : CNC01 Relay wire

• If no buttons are pressed within 30 seconds after the custom code is displayed, the
system returns to the original clock display. In this case, start again from step 1.
• The air conditioner custom code is set to A prior to shipment.

15.FUNCTION SETTING
Perform the “FUNCTION SETTING” according to the installation conditions using the remote
Rib
Wired remote controller cable controller.

Installing the external connect kit terminal (sold separately) CAUTION

Connect the wire of external input/output to the board of external connect kit. • Confirm whether the wiring work for outdoor unit has been finished.
(EXTERNAL INPUT CONNECT TO NO. CNA01
EXTERNAL OUTPUT CONNECT TO NO. CNB01, CNB02 ) • Confirm that the cover for the electrical enclosure on the outdoor unit is in place.

Operation Status Output

• This procedure changes to the function settings used to control the indoor unit according
connector : CNB01 (White connector)
to the installation conditions. Incorrect settings can cause the indoor unit to malfunction.
Error Status Output • After the power is turned on, perform the “FUNCTION SETTING” according to the
connector : CNB02 (Black connector) installation conditions using the remote controller.
Control Input • The settings may be selected between the following two: Function Number or Setting
(Operation/Stop or Forced stop) Value.
connector : CNA01 (White connector)
• Settings will not be changed if invalid numbers or setting values are selected.
• Refer to the installation manual enclosed with the remote control unit when the wired
remote control unit (option) is used.

Entering the Function Setting Mode

While pressing the POWERFUL button and TEMP. ( ) button simultaneously, press the
RESET button to enter the function setting mode.

Selecting the Function Number and Setting Value [Reverse cycle model]
External (1) Press the TEMP. ( / ) buttons to select the func- Function Number
connect kit cable Rib tion number. (Press the 10°C HEAT button to switch
between the left and right digits.)
Fixing the wires
(2) Press the POWERFUL button to proceed to setting
After connecting the terminals, thread the wires through the clasp and rib of the control box as value. (Press the POWERFUL button again to return to
circled in the figure below. the function number selection.)
Then fix the wires onto the control box with the provided cable tie. Setting
(3) Press the TEMP. ( / ) buttons to select the setting Value
value. (Press the 10°C HEAT button to switch between
the left and right digits.)
(4) Press the MODE button once to send the function set-
ting information. Please confirm the beeping sound.
(5) Next, please press START/STOP ( ) button once
to fix the function setting. Please confirm the beeping
sound.
(6) Press the RESET button to cancel the function setting
Relay control board mode.
Cable tie
(7) After completing the FUNCTION SETTING, be sure to
13.2.5. Installing the control cover disconnect the power and reconnect it again.
(1) Attach the control cover.
(2) Attach the 2 screws.

13.2.6. Labelling
Paste the wiring label beside the label for schematic diagram inside the front panel.

13.2.7. Installing the front panel and intake grille

(See “9. FRONT PANEL REMOVAL AND INSTALLATION” and “9.2. Front panel installation”)

En-10

9320456023-02_IM_EN.indd 10 10/6/2017 4:32:18 PM

 Selecting the Function Number and Setting Value [Cool model] Room temperature sensor switching
(1) Press the TEMP. ( / ) buttons to select the func- Function Number (Only for wired remote controller)
tion number. (Press the ECONOMY button to switch When using the Wired remote controller temperature sensor, change the setting to “Both”
between the left and right digits.) (01).
(♦... Factory setting)
(2) Press the POWERFUL button to proceed to setting
value. (Press the POWERFUL button again to return to Function
Setting Description Setting Value
the function number selection.)
Number
Setting
Value ♦ Indoor unit 00
(3) Press the TEMP. ( / ) buttons to select the setting 42
value. (Press the ECONOMY button to switch between Both 01
the left and right digits.)
00: Sensor on the indoor unit is active.
(4) Press the MODE button once to send the function set- 01: Sensors on both indoor unit and wired remote controller are active.
ting information. Please confirm the beeping sound. * Remote controller sensor must be turned on by using the remote controller.
(5) Next, please press START/STOP ( ) button once
to fix the function setting. Please confirm the beeping Remote controller custom code
sound. (Only for wireless remote controller)
(6) Press the RESET button to cancel the function setting The indoor unit custom code can be changed. Select the appropriate custom code.
mode. (♦... Factory setting)
(7) After completing the FUNCTION SETTING, be sure to Function
Setting Description Setting Value
disconnect the power and reconnect it again. Number
♦ A 00
CAUTION
B 01
After disconnecting the power, wait 30 seconds or more before reconnecting it again. 44
The function setting does not become active unless the power is disconnected then C 02
reconnected again.
D 03

Filter sign
Select appropriate intervals for displaying the filter sign on the indoor unit according to the
External input control
“Operation/Stop” mode or “Forced stop” mode can be selected.
estimated amount of dust in the air of the room.
(♦... Factory setting)
If the indication is not required, select “No indication” (03).
(♦... Factory setting) Function
Setting Description Setting Value
Number
Function
Setting Description Setting Value ♦ Operation/Stop mode 00
Number
Standard (400 hours) 00 (Setting forbidden) 46 01

Long interval (1,000 hours) 01 Forced stop mode 02

11
Short interval (200 hours) 02
Indoor unit fan control for energy saving for cooling
♦ No indication 03 Enables or disables the power-saving function by controlling the indoor unit fan rotation when
the outdoor unit is stopped during cooling operation.
(♦... Factory setting)
Room temperature control for cooling
Depending on the installed environment, correction of the room temperature sensor may Function
Setting Description Setting Value
Number
be required. Select the appropriate control setting according to the installed environment.
(♦... Factory setting) ♦ Disable 00
49
Function Enable 01
Setting Description Setting Value
Number
♦ Standard 00 00: When the outdoor unit is stopped, the indoor unit fan operates continuously following
the setting on the remote controller.
Slightly lower control 01
01: When the outdoor unit is stopped, the indoor unit fan operates intermittently at a very
30
Lower control 02 low speed.

Higher control 03 Setting record

Record any changes to the settings in the following table.
Setting Description Setting Value
Room temperature control for heating [Reverse cycle model only]
Depending on the installed environment, correction of the room temperature sensor may Filter sign
be required. Select the appropriate control setting according to the installed environment.
Room temperature control for cooling
(♦... Factory setting)
Function Room temperature control for heating
Setting Description Setting Value
Number
Auto restart
♦ Standard 00
Room temperature sensor switching
Lower control 01
31 Remote controller custom code
Slightly higher control 02
External input control
Higher control 03
Indoor unit fan control for energy saving for cooling

Auto restart After completing the FUNCTION SETTING, be sure to disconnect the power and recon-
Enable or disable automatic restart after a power interruption. nect it again.
(♦... Factory setting)
Function
Setting Description Setting Value
Number
♦ Enable 00
40
Disable 01

* Auto restart is an emergency function such as for power outage etc. Do not attempt to
use this function in normal operation. Be sure to operate the unit by remote controller or
external device.

En-11

9320456023-02_IM_EN.indd 11 10/6/2017 4:32:19 PM

 16.CUSTOMER GUIDANCE ●(7) ●(6) ◊
• 2-way valve temp. sensor error
• 3-way valve temp. sensor error
Heat sink temp. sensor error
Explain the following to the customer in accordance with the operating manual:
(1) Starting and stopping method, operation switching, temperature adjustment, timer, airflow
●(7) ●(7) ◊
switching, and other remote control unit operations. • Sub-cool Heat Ex. gas inlet
(2) Air filter removal and cleaning, and how to use the air louvers.
temp. sensor error
(3) Give the operating manual to the customer. ●(8) ●(2) ◊
• Sub-cool Heat Ex. gas outlet
temp. sensor error
17.ERROR CODES ●(8) ●(3) ◊
Liquid pipe temp. sensor error

If you use a wireless remote controller, the lamp on the photo detector unit will output error Current sensor error
codes by way of blinking patterns. If you use a wired remote controller, error codes will ap- ●(8) ●(4) ◊
pear on the remote control display. See the lamp blinking patterns and error codes in the
table. An error display is displayed only during operation. • Discharge pressure sensor error
●(8) ●(6) ◊ • Suction pressure sensor error
Error display Wired • High pressure switch error
OPERATION TIMER ECONOMY remote Trip detection
lamp lamp lamp controller
Description ●(9) ●(4) ◊
(green) (orange) (green) Error code Compressor rotor position
Serial communication error
●(9) ●(5) ◊ detection error
●(1) ●(1) ◊
Outdoor unit fan motor error
Wired remote controller
●(9) ●(7) ◊
●(1) ●(2) ◊ communication error 4-way valve error
Check run unfinished
●(9) ●(9) ◊
●(1) ●(5) ◊
Discharge temp. error
Unit number or Refrigerant circuit
●(10) ●(1) ◊
●(2) ●(1) ◊ address setting error Compressor temp. error
[Simultaneous Multi] ●(10) ●(3) ◊
Indoor unit capacity error High pressure error
●(2) ●(2) ◊ ●(10) ●(4) ◊
Combination error Low pressure error
●(2) ●(3) ◊ ●(10) ●(5) ◊
• Connection unit number error Branch boxes error
(indoor slave unit) ●(13) ●(2) ◊ [Flexible Multi]
[Simultaneous Multi]
●(2) ●(4) ◊ • Connection unit number error
Display mode ● : 0.5s ON / 0.5s OFF
◊ : 0.1s ON / 0.1s OFF
(indoor unit or branch unit)
( ) : Number of flashing
[Flexible Multi]
Primary unit, secondary unit
●(2) ●(7) ◊ set-up error [Simultaneous Multi] [Troubleshooting with the indoor unit display]
Indoor unit PCB model
●(3) ●(2) ◊ information error
Manual auto switch error
●(3) ●(5) ◊
Room temp. sensor error
●(4) ●(1) ◊
Indoor unit Heat Ex. Middle temp.
●(4) ●(2) ◊ sensor error
Indoor unit fan motor error OPERATION indicator (green)
●(5) ●(1) ◊
TIMER indicator (orange)
Drain pump error ECONOMY indicator (green)
●(5) ●(3) ◊
Damper error [Troubleshooting with the Wired Remote Controller Display (Option)]
●(5) ●(7) ◊ If an error occurs, the following display will be shown. (“Er” will appear in the set room
temperature display.)
Intake grille error
●(5) ●(8) ◊
Indoor unit error
●(5) ●(15) ◊
Error code
Outdoor unit main PCB model
●(6) ●(2) ◊ information error or
communication error
Inverter error
●(6) ●(3) ◊
Active filter error, PFC circuit error
●(6) ●(4) ◊
Trip terminal L error
●(6) ●(5) ◊
Display PCB microcomputers
●(6) ●(10) ◊ communication error
Discharge temp. sensor error
●(7) ●(1) ◊
Compressor temp. sensor error
●(7) ●(2) ◊
Outdoor unit Heat Ex. liquid temp.
●(7) ●(3) ◊ sensor error
Outdoor temp. sensor error
●(7) ●(4) ◊
Suction Gas temp. sensor error
●(7) ●(5) ◊

En-12

9320456023-02_IM_EN.indd 12 10/6/2017 4:32:19 PM