PRODUCT SHEET
Communicator
EtherCAT MainDevice
Need to connect your EtherCAT device to another device running
on different industrial networks? The Anybus Communicator has
your back! No special cables, software, or training is required.
The EtherCAT MainDevice from Anybus are designed to ensure
reliable, secure, and high-speed data transfer between EtherCAT
and different industrial Ethernet and Fieldbus networks. Very easy
to install and deploy, the stand-alone gateways enable transparent
data exchange allowing you to both bridge and integrate legacy
equipment into modern high-performance networks.
High performance Cybersecurity
Instant data transfer of up to 1500 bytes Designed to keep you safe from cyberat-
with hardware accelerated endian con- tacks. Secure boot protects you against
version (byte swap) enables you to take malicious software and a security switch
full advantage of high-speed industrial adds physical protection to prevent un-
networks. authorized configuration changes.
Durability User-friendly
Built using carefully selected industrial Fast installation and configuration are
components and verified against indus- guaranteed thanks to an intuitive web
try standards. Proven network confor- user interface, ethernet configuration
mance thanks to the market-leading cable, easy-to-understand documenta-
NP40 network processor. tion, and effective housing design.
Product selection
Article nr Control sys. 1 Device(s)
ABC3113 PROFINET EtherCAT
ABC3107 Ethernet/IP EtherCAT
ABC3128 Modbus TCP EtherCAT
ABC3100 PROFIBUS EtherCAT
ABC3190 Common Eth.* EtherCAT
*Common ethernet: select among EtherNet/IP, Modbus TCP and PROFINET control system
PRODUCT SHEET
Scan for more info
General about our products
Dimensions with connectors (L x W x H) 98 x 27 x 144 mm / 3.85 x 1.06 x 5,67 in
Weight 150 grams, 0.33 lb
IP rating IP20
Housing material PC ABS, UL 94 VO
Mounting DIN rail (35 * 7,5/15)
Operating temperature -25 to 70° C, -13 to 158° F
Configuration Web based via Ethernet configuration port
Industrial network connector(s) 2xRJ45 10/100 Mbit (daisy chaining) / DB9 (PROFIBUS)
Certification CE, UKCA, UL ord loc (E214107), KC, RMC
MTBF > 1 500 000 h, Telcordia Method I Case 3 at 30° C
Power
Input voltage 12 - 30 VDC
Current consumption Typical: 160 mA @ 24V Max: 400 mA @ 12V
Power connector 3-pin plug with screw terminal
Protection Reverse voltage protection and short circuit protection
Network specifications
EtherCAT MainDevice
- Transfer up to 1 500 bytes to EtherCAT SubDevices - 1ms minimum cycle time*
- Transfer up to 1 500 bytes from EtherCAT SubDevices - Gateway latency < 1ms (when in sync)
- Total supported cyclic process data: 3000 bytes - Endian conversion (without affecting latency)
- Up to 24 nodes (SubDevices) - CAN over EtherCAT (COE)
- Configuration by scanning EtherCAT nodes (SubDevices) - Live list published as process data
PROFINET IO Device Modbus TCP Server
- Transfer up to 1 024 bytes from PROFINET
- Transfer up to 1 024 bytes to - Transfer up to 1 500 bytes to Modbus TCP
PROFINET - Transfer up to 1 500 bytes from Modbus TCP
- Total supported cyclic process data: 2048 bytes - Total supported process data: 3 000 bytes
- 1 ms minimum cycle time - 4 connections
- Conformance class B, Real-Time (RT) - Function codes 01-06, 15-16, 23, 43/14
- Network load robustness, Netload Class III
Ethernet/IP Adapter PROFIBUS DP Device (DPV1/DPV0)
- Transfer up to 1 448 bytes to EtherNet/IP - Transfer up to 244 bytes to PROFIBUS
- Transfer up to 1 448 bytes from EtherNet/IP - Transfer up to 244 bytes from PROFIBUS
- Total supported cyclic process data: 2896 bytes - Total supported process data: 488 bytes
- Class 1 and Class 3 connection for process data - Automatic baud rate detection up to 12 Mbit/s
- Device Level Ring (beacon mode) - Sync, Freeze and Watchdog
- Quick Connect class B - I&M Ident numbers 0-31x
* Depending on the application
