Scribd
Upload
17 views3 pages

B.E / B.Tech Practical End Semester Examinations, April / May 2019

This document outlines the practical examination details for the Hydraulic Engineering Laboratory course for the fourth semester, including the time duration, maximum marks, and mark allocation for various components. It lists a series of experiments that students can perform, each with a maximum score of 100 marks, covering topics such as flow measurement, pump characteristics, and turbine efficiency. The document serves as a guideline for students to prepare for their practical exams.

Uploaded by

sharesiva81
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
17 views3 pages

B.E / B.Tech Practical End Semester Examinations, April / May 2019

This document outlines the practical examination details for the Hydraulic Engineering Laboratory course for the fourth semester, including the time duration, maximum marks, and mark allocation for various components. It lists a series of experiments that students can perform, each with a maximum score of 100 marks, covering topics such as flow measurement, pump characteristics, and turbine efficiency. The document serves as a guideline for students to prepare for their practical exams.

Uploaded by

sharesiva81
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 3

Page 1 of 3

B.E / B.Tech PRACTICAL END SEMESTER EXAMINATIONS, APRIL / MAY


2019
Fourth Semester

CE8461 - HYDRAULIC ENGINEEIRNG LABORATORY


(Regulations 2017)

Time: 3 Hours Student can Perform Any One Experiment


Max. Marks 100

(MARK ALLOCATION)
AIM / PRINCIPLE / FORMULA /
TABULATION /
APPARATUS CALCULATION VIVA- RECOR
CIRCUIT / PROGRAM / TOTAL
REQUIRED / / GRAPHS & VOCE D
DRAWING
PROCEDURE RESULTS
20 25 35 10 10 100

1) (a) Calibrate the rate of flow through the given pipe by using
Rotameter (50)

(b) Calculate the velocity of flow using the Pitot tube fitted in the pipe.
(50)

2) Determine the coefficient of discharge of a given Orifice meter and


obtain the same through graphical plot.
(100)

3) Determine the coefficient of discharge of a given Venturi meter and


obtain the same through graphical plot.
(100)

4) Determine of the coefficient of discharge of a given Orifice with


constant heads.

(100)

5) Determine the coefficient of discharge of a given Mouthpiece with


constant heads.
(100)
Page 2 of 3

6) Prove the total energy of flow through pipe is constant through various
duct area by Bernoulli’s experiment.
(100)

7) Determine of friction factor or coefficient of friction for given set of


pipes. (Steel and Aluminum)
(100)

8) Determine the friction factor and Chezy’s constant for the given set of
pipe. (Brass and Stainless Steel)
(100)

9) Determination of minor losses or loss coefficients for the given set pipe
fittings like elbow, bend, contraction and expansion. (any Two)
(100)

10) Conduct an experiment and draw the characteristics curves of


centrifugal pump with Variable speed method.
(100)

11) Conduct an experiment and draw the characteristics curves of


centrifugal pump with Constant speed method.
(100)

12) Conduct an experiment and draw the characteristics curves of


reciprocating pump.
(100)

13) Conduct an experiment and draw the characteristics curves of Gear


pump. (100)

14) Conduct an experiment and draw the characteristics curves of


Submersible pump.
(100)
Page 3 of 3

15) Conduct an experiment to determine the maximum efficiency and


draw the characteristics curves of Pelton wheel Turbine using variable
speed. (100)

16) Conduct an experiment and draw the characteristics curves of Francis


Turbine and determine its maximum efficiency.
(100)

17) Determine the maximum efficiency of a Kaplan Turbine and draw its
characteristics curves.
(100)

18) Determine the stability and Meta centric height of a given ship model.
(100)

19) Determine the maximum efficiency of Displacement pump and draw


its characteristics curves.
(100)

You might also like