Ex.
No: DATE:
FULL WAVE RECTIFIER CIRCUIT.
AIM:
To design the single side PCB layout for full wave rectifier circuit with
MULTISIM.
APPARATUS REQUIRED:
1. PC loaded with MULTISIM software.
2. Laser printer.
PROCEDURE:
• Open MULTISIM Software, Click=> File => New => Design.
• Click File => save as in Desk Top and rename the Design1 to your circuit name
then save.
• Go to Component tool bar and select the components then connect as per
given circuit diagram and save it.
• Test the circuit with simulation RUN button.
• Remove Power source and output device with replacement of connector.
• Change Properties of the all component into PCB Mode.
• Go to Transfer icon => Transfer to Ulti board 12.0 then save the file and got
Import net list and click ok.
• Go to OPTIONS icon Select PCB Properties icon and select copper layers Click
properties un tick routing click ok for single side PCB.
• Select all components into Board Outline and make small PCB size with the help
of board Outline.
• Click Auto route icon then click auto router to make PCB Layout.
• Finally print the PCB Layout with help of printer.
1
SIMULATION CIRCUIT:
PCB LAYOUT CIRCUIT:
2
PCB LAYOUT OUTPUT:
3
4
Ex. No: DATE:
BRIDGE RECTIFIER.
AIM:
To design the single sided PCB layout for Bridge rectifier circuit
with MULTISIM.
APPARATUS REQUIRED:
1. PC loaded with MULTISIM software.
2. Laser printer.
PROCEDURE:
• Open MULTISIM Software, Click=> File => New => Design.
• Click File => save as in Desk Top and rename the Design1 to your circuit
name then save.
• Go to Component tool bar and select the components then connect as per given
circuit diagram and save it.
• Test the circuit with simulation RUN button.
• Remove Power source and output device with replacement of connector.
• Change Properties of the all component into PCB Mode.
• Go to Transfer icon => Transfer to Ulti board 12.0 then save the file and got
Import net list and click ok.
• Go to OPTIONS icon Select PCB Properties icon and select copper layers
Click properties un tick routing click ok for single side PCB.
• Select all components into Board Outline and make small PCB size with the help
of board Outline.
• Click Auto route icon then click auto router to make PCB Layout.
• Finally print the PCB Layout with help of printer
5
SIMULATION CIRCUIT:
PCB LAYOUT CIRCUIT:
6
PCB LAYOUT OUTPUT:
7
8
Ex. No: DATE:
COMMON EMITTER AMPLIFIER (CE)
AIM:
To design the single sided PCB layout for Common Emitter Amplifier circuit
with MULTISIM.
APPARATUS REQUIRED:
1. PC loaded with MULTISIM software.
2. Laser printer.
PROCEDURE:
• Open MULTISIM Software, Click=> File => New => Design.
• Click File => save as in Desk Top and rename the Design1 to your circuit name
then save.
• Go to Component tool bar and select the components then connect as per
given circuit diagram and save it.
• Test the circuit with simulation RUN button.
• Remove Power source and output device with replacement of connector.
• Change Properties of the all component into PCB Mode.
• Go to Transfer icon => Transfer to Ulti board 12.0 then save the file and got
Import net list and click ok.
• Go to OPTIONS icon Select PCB Properties icon and select copper layers Click
properties un tick routing click ok for single side PCB.
• Select all components into Board Outline and make small PCB size with the help
of board Outline.
• Click Auto route icon then click auto router to make PCB Layout.
• Finally print the PCB Layout with help of printer
9
SIMULATION CIRCUIT:
PCB LAYOUT CIRCUIT:
R1 R3
100kΩ 1kΩ
R1 R3 C2
100kΩ 1kΩ
J2
C210µF
J1
Q1
C1
10µF J2
J1 HDR1X2
10µF Q1
C1 BC547A
HDR1X3 HDR1X2
10µF
R2 BC547A
HDR1X3
150kΩ R4 C3
R2 470Ω 47µF
150kΩ R4 C3
470Ω 47µF
PCB LAYOUT OUTPUT:
11
12
Ex. No: DATE:
AMPLITUDE MODULATOR CIRCUIT
AIM:
To design the single sided PCB layout for Amplitude Modulator circuit
with MULTISIM.
APPARATUS REQUIRED:
1. PC loaded with MULTISIM software.
2. Laser printer.
PROCEDURE:
• Open MULTISIM Software, Click=> File => New => Design.
• Click File => save as in Desk Top and rename the Design1 to your circuit name
then save.
• Go to Component tool bar and select the components then connect as per
given circuit diagram and save it.
• Test the circuit with simulation RUN button.
• Remove Power source and output device with replacement of connector.
• Change Properties of the all component into PCB Mode.
• Go to Transfer icon => Transfer to Ulti board 12.0 then save the file and got
Import net list and click ok.
• Go to OPTIONS icon Select PCB Properties icon and select copper layers Click
properties un tick routing click ok for single side PCB.
• Select all components into Board Outline and make small PCB size with the help
of board Outline.
• Click Auto route icon then click auto router to make PCB Layout.
• Finally print the PCB Layout with help of printer
13
SIMULATION CIRCUIT:
PCB LAYOUT CIRCUIT:
14
PCB LAYOUT OUTPUT:
15
16
Ex. No: DATE:
FREQUENCY MODULATOR CIRCUIT
AIM:
To design the single sided PCB layout for Frequency Modulator circuit with
MULTISIM.
APPARATUS REQUIRED:
1. PC loaded with MULTISIM software.
2. Laser printer.
PROCEDURE:
• Open MULTISIM Software, Click=> File => New => Design.
• Click File => save as in Desk Top and rename the Design1 to your circuit name
then save.
• Go to Component tool bar and select the components then connect as per
given circuit diagram and save it.
• Test the circuit with simulation RUN button.
• Remove Power source and output device with replacement of connector.
• Change Properties of the all component into PCB Mode.
• Go to Transfer icon => Transfer to Ulti board 12.0 then save the file and got
Import net list and click ok.
• Go to OPTIONS icon Select PCB Properties icon and select copper layers Click
properties un tick routing click ok for single side PCB.
• Select all components into Board Outline and make small PCB size with the help
of board Outline.
• Click Auto route icon then click auto router to make PCB Layout.
• Finally print the PCB Layout with help of printer
17
SIMULATION CIRCUIT:
PCB LAYOUT CONNECTION:
18
PCB LAYOUT OUTPUT:
19
20
Ex. No: DATE:
ASTABLE MULTIVIBRATOR USING 555 IC
AIM:
To design the single sided PCB layout for Astable Multi vibrator using 555
IC with MULTISIM.
APPARATUS REQUIRED:
1. PC loaded with MULTISIM software.
2. Laser printer.
PROCEDURE:
• Open MULTISIM Software, Click=> File => New => Design.
• Click File => save as in Desk Top and rename the Design1 to your circuit
name then save.
• Go to Component tool bar and select the components then connect as per given
circuit diagram and save it.
• Test the circuit with simulation RUN button.
• Remove Power source and output device with replacement of connector.
• Change Properties of the all component into PCB Mode.
• Go to Transfer icon => Transfer to Ulti board 12.0 then save the file and got
• Go to OPTIONS icon Select PCB Properties icon and select copper layers
Click properties un tick routing click ok for single side PCB.
• Select all components into Board Outline and make small PCB size with the help
of board Outline.
• Click Auto route icon then click auto router to make PCB Layout.
• Finally print the PCB Layout with help of printer
21
SIMULATION CIRCUIT:
PCB LAYOUT CIRCUIT:
22
PCB LAYOUT OUTPUT:
23
24
Ex. No: DATE:
HALF ADDER USING LOGIC GATES.
AIM:
To design the single sided PCB layout for Half Adder using Logic gates with
MULTISIM.
APPARATUS REQUIRED:
1. PC loaded with MULTISIM software.
2. Laser printer.
PROCEDURE:
• Open MULTISIM Software, Click=> File => New => Design.
• Click File => save as in Desk Top and rename the Design1 to your circuit
name then save.
• Go to Component tool bar and select the components then connect as per given
circuit diagram and save it.
• Test the circuit with simulation RUN button.
• Remove Power source and output device with replacement of connector.
• Change Properties of the all component into PCB Mode.
• Go to Transfer icon => Transfer to Ulti board 12.0 then save the file and got
Import net list and click ok.
• Go to OPTIONS icon Select PCB Properties icon and select copper layers Click
properties un tick routing click ok for single side PCB.
• Select all components into Board Outline and make small PCB size with the help
of board Outline.
• Click Auto route icon then click auto router to make PCB Layout.
• Finally print the PCB Layout with help of printer
25
SIMULATION CIRCUIT:
PCB LAYOUT CONNECTION:
26
PCB LAYOUT OUTPUT:
27
28
Ex. No: DATE:
FULL ADDER USING LOGIC GATES.
AIM:
To design the single sided PCB layout for Full Adder using Logic gates with
MULTISIM.
APPARATUS REQUIRED:
1. PC loaded with MULTISIM software.
2. Laser printer.
PROCEDURE:
• Open MULTISIM Software, Click=> File => New => Design.
• Click File => save as in Desk Top and rename the Design1 to your circuit name
then save.
• Go to Component tool bar and select the components then connect as per given
circuit diagram and save it.
• Test the circuit with simulation RUN button.
• Remove Power source and output device with replacement of connector.
• Change Properties of the all component into PCB Mode.
• Go to Transfer icon => Transfer to Ulti board 12.0 then save the file and
got Import net list and click ok.
• Go to OPTIONS icon Select PCB Properties icon and select copper layers Click
properties un tick routing click ok for single side PCB.
• Select all components into Board Outline and make small PCB size with the
help of board Outline.
• Click Auto route icon then click auto router to make PCB Layout.
• Finally print the PCB Layout with help of printer
29
SIMULATION CIRCUIT:
PCB LAYOUT CIRCUIT:
30
PCB LAYOUT OUTPUT:
31
32
Ex. No: DATE:
4 BIT BINARY COUNTER USING D FLIP FLOPS.
AIM:
To design the single sided PCB layout for 4 Bit Binary Counter using D Flip Flops
with MULTISIM.
APPARATUS REQUIRED:
1. PC loaded with MULTISIM software.
2. Laser printer.
PROCEDURE:
• Open MULTISIM Software, Click=> File => New => Design.
• Click File => save as in Desk Top and rename the Design1 to your circuit name
then save.
• Go to Component tool bar and select the components then connect as per given
circuit diagram and save it.
• Test the circuit with simulation RUN button.
• Remove Power source and output device with replacement of connector.
• Change Properties of the all component into PCB Mode.
• Go to Transfer icon => Transfer to Ulti board 12.0 then save the file and
got Import net list and click ok.
• Go to OPTIONS icon Select PCB Properties icon and select copper layers Click
properties un tick routing click ok for single side PCB.
• Select all components into Board Outline and make small PCB size with the
help of board Outline.
• Click Auto route icon then click auto router to make PCB Layout.
• Finally print the PCB Layout with help of printer
33
SIMULATION CIRCUIT:
PCB LAYOUT CIRCUIT:
34
PCB LAYOUT OUTPUT:
35
36
Ex. No: DATE:
4 BIT SHIFT REGISTER (PIPO) USING JK FLIP FLOPS.
AIM:
To design the single sided PCB layout for 4 Bit Shift Register (PIPO) using
JK Flip Flops with MULTISIM.
APPARATUS REQUIRED:
1. PC loaded with MULTISIM software.
2. Laser printer.
PROCEDURE:
• Open MULTISIM Software, Click=> File => New => Design.
• Click File => save as in Desk Top and rename the Design1 to your circuit name
then save.
• Go to Component tool bar and select the components then connect as per given
circuit diagram and save it.
• Test the circuit with simulation RUN button.
• Remove Power source and output device with replacement of connector.
• Change Properties of the all component into PCB Mode.
• Go to Transfer icon => Transfer to Ulti board 12.0 then save the file and
got Import net list and click ok.
• Go to OPTIONS icon Select PCB Properties icon and select copper layers Click
properties un tick routing click ok for single side PCB.
• Select all components into Board Outline and make small PCB size with the
help of board Outline.
• Click Auto route icon then click auto router to make PCB Layout.
• Finally print the PCB Layout with help of printer
37
PCB LAYOUT CIRCUIT:
38
PCB LAYOUT OUTPUT:
39
40
Ex. No: DATE:
POSITIVE VOLTAGE REGULATOR USING 7805 AND 7812 IC.
AIM:
To design the single sided PCB layout for Positive Voltage regulator using
7805 and 7812 IC with MULTISIM.
APPARATUS REQUIRED:
1. PC loaded with MULTISIM software.
2. Laser printer.
PROCEDURE:
• Open MULTISIM Software, Click=> File => New => Design.
• Click File => save as in Desk Top and rename the Design1 to your circuit name
then save.
• Go to Component tool bar and select the components then connect as per given
circuit diagram and save it.
• Test the circuit with simulation RUN button.
• Remove Power source and output device with replacement of connector.
• Change Properties of the all component into PCB Mode.
• Go to Transfer icon => Transfer to Ulti board 12.0 then save the file and
got Import net list and click ok.
• Go to OPTIONS icon Select PCB Properties icon and select copper layers Click
properties un tick routing click ok for single side PCB.
• Select all components into Board Outline and make small PCB size with the
help of board Outline.
• Click Auto route icon then click auto router to make PCB Layout.
• Finally print the PCB Layout with help of printer.
41
SIMULATION CIRCUIT:
PCB LAYOUT CIRCUIT:
42
PCB LAYOUT OUTPUT:
43
44
Ex. No: DATE:
ANALOG MULTIPLIER USING 741 IC.
AIM:
To design the single sided PCB layout for Analog Multiplier using 741 IC
with MULTISIM.
APPARATUS REQUIRED:
1. PC loaded with MULTISIM software.
2. Laser printer.
PROCEDURE:
• Open MULTISIM Software, Click=> File => New => Design.
• Click File => save as in Desk Top and rename the Design1 to your circuit name
then save.
• Go to Component tool bar and select the components then connect as per given
circuit diagram and save it.
• Test the circuit with simulation RUN button.
• Remove Power source and output device with replacement of connector.
• Change Properties of the all component into PCB Mode.
• Go to Transfer icon => Transfer to Ulti board 12.0 then save the file and
got Import net list and click ok.
• Go to OPTIONS icon Select PCB Properties icon and select copper layers Click
properties un tick routing click ok for single side PCB.
• Select all components into Board Outline and make small PCB size with the
help of board Outline.
• Click Auto route icon then click auto router to make PCB Layout.
• Finally print the PCB Layout with help of printer.
45
SIMULATION CIRCUIT:
PCB LAYOUT CIRCUIT:
46
PCB LAYOUT OUTPUT:
47
48
Ex. No: DATE:
FLASHING LEDS USING 555 IC.
AIM:
To design the single sided PCB layout for Flashing LEDs using 555 IC with
MULTISIM.
APPARATUS REQUIRED:
1. PC loaded with MULTISIM software.
2. Laser printer.
PROCEDURE:
• Open MULTISIM Software, Click=> File => New => Design.
• Click File => save as in Desk Top and rename the Design1 to your circuit name
then save.
• Go to Component tool bar and select the components then connect as per given
circuit diagram and save it.
• Test the circuit with simulation RUN button.
• Remove Power source and output device with replacement of connector.
• Change Properties of the all component into PCB Mode.
• Go to Transfer icon => Transfer to Ulti board 12.0 then save the file and
got Import net list and click ok.
• Go to OPTIONS icon Select PCB Properties icon and select copper layers Click
properties un tick routing click ok for single side PCB.
• Select all components into Board Outline and make small PCB size with the
help of board Outline.
• Click Auto route icon then click auto router to make PCB Layout.
• Finally print the PCB Layout with help of printer.
49
SIMULATION CIRCUIT:
PCB LAYOUT CIRCUIT:
50
PCB LAYOUT OUTPUT:
51
52
Ex. No: DATE:
FAN REGULATOR.
AIM:
To design the single side PCB layout for Fan Regulator with MULTISIM
APPARATUS REQUIRED:
1. PC loaded with MULTISIM software.
2. Laser printer.
PROCEDURE:
• Open MULTISIM Software, Click=> File => New => Design.
• Click File => save as in Desk Top and rename the Design1 to your circuit name
then save.
• Go to Component tool bar and select the components then connect as per given
circuit diagram and save it.
• Test the circuit with simulation RUN button.
• Remove Power source and output device with replacement of connector.
• Change Properties of the all component into PCB Mode.
• Go to Transfer icon => Transfer to Ulti board 12.0 then save the file and
got Import net list and click ok.
• Go to OPTIONS icon Select PCB Properties icon and select copper layers Click
properties un tick routing click ok for single side PCB.
• Select all components into Board Outline and make small PCB size with the
help of board Outline.
• Click Auto route icon then click auto router to make PCB Layout.
• Finally print the PCB Layout with help of printer.
53
SIMULATION CIRCUIT:
PCB LAYOUT CIRCUIT:
54
PCB LAYOUT OUTPUT:
55
56
Ex. No: DATE:
LIQUID LEVEL CONTROLLER.
AIM:
To design single side PCB layout for Liquid Level Controller with MULTISIM
APPARATUS REQUIRED:
1. PC loaded with MULTISIM software.
2. Laser printer.
PROCEDURE:
• Open MULTISIM Software, Click=> File => New => Design.
• Click File => save as in Desk Top and rename the Design1 to your circuit name
then save.
• Go to Component tool bar and select the components then connect as per given
circuit diagram and save it.
• Test the circuit with simulation RUN button.
• Remove Power source and output device with replacement of connector.
• Change Properties of the all component into PCB Mode.
• Go to Transfer icon => Transfer to Ulti board 12.0 then save the file and got
• Go to OPTIONS icon Select PCB Properties icon and select copper layers
Click properties un tick routing click ok for single side PCB.
• Select all components into Board Outline and make small PCB size with the help
of board Outline.
• Auto route icon then click auto router to make PCB Layout.
• Finally print the PCB Layout with help of printer
57
SIMULATION CIRCUIT:
PCB LAYOUT CIRCUIT:
58
PCB LAYOUT OUTPUT:
59
60
